Search Documents

By Armstrong

This is a world of change and has been from the beginning. There are constant efforts on the part of natural forces to wear down the high spots and fill in the low spots. Wind and water over eons of time tunnel through obstacles and build windways and waterways to make movement of air and water easier and more efficient. It is a natural, never ending, ever changing continuing effort. Man in his struggle to survive, and to progress, has had to adapt the terrain of the earth to fit his needs the best he could. First, he used natural caves to protect him from the elements; then he learned how to build earth and rock-moving tools from antlers, bone, rocks, and sticks and adapted his cave to increase his security and provide better protection from heat and cold and from his predatory enemies. As his numbers increased, so did the necessity of further adapting his environment to accommodate his needs. Water was usually not available when and where needed, especially in the desert areas where civilization developed, and long tunnels were drilled to intercept ground waters and lead them to underground caves carved out of soft limestone. Most of the tunnels of early man were to bring water from where it was to where man needed it. Then, as now, as man increased his chances for physical survival, he turned to the quality of life -- and this reflected in the concern for life after death. This lead to the elaborate shafts and tunnels for the protection and prservation of the more affluent noblemen and pharaohs of the early Egyptian civilization. Man used the underground for the stable temperature and for protection and safety.

Jan 1, 1974

By C. Anastasiadis

The wettability of sandstone was investigated using the technique of dielectric spectroscopy in the frequency interval 1kHz-1MHz. The natural wetness of the material was modified to get two different sets of samples, one with sea-water wetness and the other with crude oil wetness. Measurements showed that the electric responses of water-wet and crude oil-wet samples were markedly different beside the fact that the dielectric response of both groups of samples obeys a general fractional power law. The dispersivity, of the complex permittivity component that expresses the material loss with respect to the electric field was found to be the most suitable parameter to check the wettability of the samples.

Jan 1, 2005

By Randal J. Barnes

Computer based techniques for solving the Ultimate Pit Limit Problem have appeared in mining literature since the early 1960's. The majority of papers pertaining to this subject can be partitioned into one of two categories: discussion of the pros and cons of a particular algorithm, or a case study presenting specific applications of an algorithm. Subsequently, there has a1 so been considerable debate concerning the best techniques between, essentially, two camps: those favoring the moving cones techniques, and those favoring the techniques which yield true optimal pit designs. The purpose of this paper is not to add to this debate, but rather to present a few new ideas (partially a new look at an old idea), which can be easily implemented to noticeably improve any ultimate pit limit approach independent of the particular algorithm used. These ideas fall under the heading of "bounding the optimum" (Barnes and Johnson, 1980).

Jan 1, 1982

By Joel Nonnweiler, Galen Samuelson Nagle

The Sacramento Regional County Sanitation District (SRCSD) has undertaken an interceptor expansion program to meet future wastewater needs associated with projected growth over the next 20 years. The Lower Northwest Interceptor (LNWI) will include over 17 miles (27 kilometers) of pipeline including 14 miles (23 kilometers) of dual force main ranging in size from 54- to 60-inch (137- to 152-centimeter) diameter and 3 miles (5 kilometers) of 120-inch (305-centimeter) diameter gravity pipeline. The estimated capital cost for the program is $331 million, with approximately $236 million in construction cost (as of November 2002). The project includes 4,700 feet (1,433meters) of tunnel including 2 crossings of the Sacramento River and one crossing of the Barge Canal, and 11 other smaller tunnel crossings beneath various creeks, sloughs, highways, and railroads. Preliminary design of the tunnels for the LNWI are discussed in this paper. The overall purpose of the preliminary design was to sufficiently define the project to allow planning level cost and schedule estimates to be performed. There have been changes to the project during final design including pipe sizes and configurations, tunnel and pipeline lengths and anticipated flows. This paper addresses only the preliminary design of the LNWI tunnels. Final design issues and changes made since completion of preliminary design are not addressed in this paper.

Jan 1, 2003

By D. W. Fohlen, B. A. Filas

The International Finance Corporation (IFC), the private investment arm of the World Bank Group (WBG), requires all IFC-financed projects to comply with its environmental and social policies and guidelines. IFC's review process involves an environmental and social assessment and the implementation of an Environmental Action Plan (EAP) that will set forth the necessary actions to bring the operation into compliance. This paper provides an overview of the environmental and social policies and guidelines that apply to mining projects and examines how WBG/IFC policies and guidelines are applied to mining projects in developing countries. In addition, it includes a review of the increased emphasis IFC is giving to social issues over the past several years based on the existing WBG policies. IFC’s process for the environmental and social review of proposed investments is briefly discussed. The paper focuses on how IFC emphasis has shifted from the traditional environmental and impact mitigation analyses of a few years ago to the integrated social and environmental awareness, action (EAP), and implementation programs (social plans) required today. Today, IFC's focus is to promote sustainable development by investing in projects that directly benefit local communities and the environment. Examples of these changes will be highlighted by a review of recent investments located in West Africa. The goalposts have not moved, but the rules of the game have become tougher.

Jan 1, 2001

By S. K. Mishra, S. B. Kanungo, D. Biswal

Jigging of the -2.8 +0.7-mm size fraction of a friable, low-grade manganese ore sample from Andhra Pradesh increased the Mn content of a concentrate by 7% to 8%, with an average recovery of 57%. The jig concentrate was mixed with the unjigged -0.7-mm size fraction and ground to -150 µm. The sample was then subjected to wet high-intensity magnetic separation (WHIMS). The magnetic fraction thus obtained showed an increase in Mn content of 6%, but with an overall recovery of only 50%. The results of hydrocyclone classification of -150- µm ground ore indicated that the method is not capable of upgrading the manganese content, as both ferromanganese oxides and aluminosilicate gangue minerals constitute the fine size fraction. However, when the nonmagnetic fraction obtained from the WHIMS of -150- µm ore is subjected to hydrocyclone classification and the underflow obtained is subjected to WHIMS again, an overall recovery of about 50% to 52% is obtained with at least a 7% to 8% increase in the Mn content of the product. The phosphorus content in the product is not reduced by either of the two combinations of methods. The complex association of phosphorus with all the major phases in the ore has been clearly demonstrated from the linear correlation between the distribution ratios of major constituent phases and phosphorus.

Jan 1, 2000

By F. Michael Wahl

With the exception of reports on commercial deposits of kaolin, fuller's earth, and other specialty type clays, there is little published information on the extent, properties, and potential uses of the clay resources of Florida. Recent studies by the Florida Bureau of Geology in cooperation with the University of Florida and the U.S. Bureau of Mines have proven the existence of two extensive Miocene clay deposits, one in peninsular Pinellas County and the other in southeastern Charlotte County. Drilling and subsequent testing of the clays from these deposits indicate their potential for economic development. Both deposits consist of montmorillonite type clays, have an average thickness of 25 to 35 feet, and are overlain by unconsolidated Pleistocene sediments. Preliminary firing tests indicate that the clays from Pinellas County are a potential raw material for lightweight aggregate production. The clay has good bloating characteristics across an acceptable temperature range with a resultant aggregate density of less than 1.00 specific gravity. The clays from Charlotte County have poorer natural bloating characteristics but might well be used after treatment or with additives. The economic potential and locations of both deposits emphasize the need for locating similar clay resources in the state that might have economic potential so that land use planning and subsequent urbanization will not prohibit their development.

Jan 1, 1972

By R. A. Jankowski, R. Gong, R. Bhaskar

The control of respirable coal dust in continuous mining sections involves careful analyses of the generation and transport of the dust, including airflow pattern analyses. Potential dust control devices must be evaluated based on their effect on both local dust transport and potential dust exposure of face personnel. The development of larger and more productive continuous miners increases the need for research on dust control and improvement of visibility in the face area. Two studies relating to underboom dust control are discussed. The first study involved the valuation of potential underboom dust control techniques to reduce operator exposure to dust and determining the relationship between the positioning of exhaust ventilation and the exposure of face personnel as a function of face and operating variables. The study involved full-scale laboratory experiments using a state- of-the-art data acquisition system. The second study related to the use of foam under a continuous miner boom and its effect on silica concentration and respirable dust. The foam study was performed in a coal mine. The laboratory studies involved the fabrication of a full-scale test facility and development of a computer based data acquisition system. This was followed by baseline data collection, smoke trace tests, detailed performance testing of various underboom dust control measures and data analyses. The underground foam test involved the design and installation of the foam generation and delivery system, testing, and data evaluation. The results of the studies are summarized in this paper.

Jan 1, 1991

By Isobel Clark

The problem of the estimation of ore reserves is essentially a simple one to describe. Given a set of sample data, at specified locations within a deposit, how can we estimate the value (or quantity) of ore in unsampled areas. The question may be posed of a whole deposit (global) or it may be more desirable to estimate smaller volumes within the planned mine area, e.g. stopes or blocks (local). Many methods have been evolved to tackle this problem, from hand-contouring of values by the mine geologist to extremely sophisticated geomathematical analysis. The main difficulty with any estimation method in this context is that it is almost impossible to check whether the "predicted" value bears a close relationship with the "actual" value. The only reliable way to decide if an estimation method has "worked" is to test the eventual value of ore against the predicted value. This is, more often than not, impossible - even allowing for the time factor involved. To know the "actual" value of a mined block it has to be sampled intensely, and these values with their positions recorded accurately. Alternatively, blocks may be passed through the concentration process individually and these results recorded. In most producing mines neither of these alternatives are practicable or seen to be-important. Another problem with comparing in-situ (so-called) mineable reserves with production figures is the introduction of many variables into the concentration process -- dilution, wastage, possible stockpiling, mill recoveries and so on.

Jan 1, 1979

By Richard Switalski, Thomas Scotese, James Morrison, Randall Essex

OVERVIEW Like many older metropolitan areas across the U.S., the Greater Cleveland area is served by a combination of separate sanitary sewers and combined sanitary-stormwater sewers. In 1966, a Master Plan was implemented by the Northeast Ohio Regional Sewer District (District) to minimize pollutant overflows into adjoining Lake Erie and its tributary rivers and streams, that would occur during wet weather events. One component of the Master Plan was to reduce the load on combined sewers by constructing new conveyances to intercept separate sanitary flows and convey them to upgraded regional waste water treatment plants for priority treatment. As part of a 15-year program to construct 74 km (46 miles) of new interceptors, the West Leg Interceptor (WLI) Project intercepts flows from four decommissioned waste water treatment plants (WWTPs), and conveys those flows to the new Southwest Interceptor (SWI), which conveys the flows to the Southerly Treatment Plant, a tertiary level treatment facility. The WLI Project was built in sections to permit decommissioning of the WWTPs as each segment of the interceptor system was completed and put into service. Flows from the first of the four WWTPs was converted to the WLI in November, 1992; the final connection was achieved in July 1994. The WLI comprises 9.1 km (5.7 miles) of 21 to 29 m (70 to 95 ft) deep mainline interceptor tunnel, four vortex drop structures, approximately 2 km (1.3 miles) of shallow tunneled connector sewer to the mainline, approximately 2.9 km (1.8 miles) of open cut connector sewers, five construction work shafts (not including one work shaft constructed under SWI Contract 6 at the north end of the WLI), and 15 access shafts.

Jan 1, 1995

By Eugene A. Lang, William R. Archibald

Early in 1972, Rocky Mountain Energy Company approached MARCONAFLO with a unique request for assistance. They controlled a series of scattered ore deposits in a remote section of Wyoming which had become increasingly valuable despite their relatively small size, great depth and low grade. At the time, MARCONAFLO was in the process of developing a tailings reclaim system which was based on the use of submersible capsules. It appeared that this basic concept might be adapted to slurry uranium ores and pump them to the surface through a bored hole. This presentation will review for you the development of this unique and potentially very important application of MARCONAFLO technology. This first slide (SLIDE 1) depicts the total mining concept envisioned by MARCONAFLO and Rocky Mountain Energy Company. A series of six self-contained mining units would be positioned through boreholes into the ore strata. An oscillating MARCONAJET would direct a high pressure jet stream into the orebody and put it into a slurry which would flow back to a slurry pump. The slurry would then be pumped to the surface and to a collection tank from which it would be transferred to processing. Both the MARCONAJET and the slurry pump would be actuated and controlled by means of a hydraulic power console mounted on the trailer behind the service tower. By means of a high pressure water pump also mounted on the trailer, return water from processing would be delivered to the MARCONAJET to slurry the ore. Tailings would be returned to a backfill unit for redepositing in the mined-out cavities. A drill rig would precede the mining, and it was estimated that this configuration would represent an optimum system for most effective equipment utilization.

Jan 1, 1976

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillar mining (panel width) is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to prefailure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25% to 40% higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Prefailure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to design improvements, as mines become deeper.

Jan 1, 2003

By C. P. Siess, S. L. Paul, E. H. Gaylord

Several types of tunnel supports are being investigated experimentally and analytically at the University of Illinois at Urbana-Champaign under the sponsorship of the Federal Railroad Administration, Department of Transportation. The results of work on two types will be discussed here. These are steel sets and continuous, monolithic steel-fiber-reinforced concrete liners. The latter is a model of a short length of liner that might result from a continuous slip-forming operation in a tunnel excavated with a boring machine. Tests have been performed on both types of support and analyses are being developed which will greatly broaden the scope of the test program. The objective of these studies is to improve the understanding of basic behavior of these supports, and to develop techniques for their analysis. The analyses will then be used to perform parameter studies that will lead to more rational procedures for structural design. The tests provide a check on the accuracy of the analysis and demonstrate the overall behavior and modes of failure. Another part of the project is concerned with the interaction of support and medium, and thus prediction of loads for the supports. These studies are presented in greater detail in a recent report (1). A brief outline of results obtained to date are presented in this paper. STUDIES OF STEEL SETS Description of Set Tests The sets tested were of the horseshoe type with a 5-ft radius arch section and 7-ft straight legs. They had bolted joints at the crown

Jan 1, 1974

By N. A. Frazier

The technology for using limestone or lime to scrub SO2 from power-plant flue gas has significant implications to the limestone industry. A brief status report on these processes will be made, possible process requirements on the limestone properties will be reviewed, and projections on the buildup of demand with respect to time will be reviewed. Disposal problems inherent with the use of these throwaway processes will also be summarized. Given a viable technology, relations among (1) distance of power plants from low- and high-sulfur coal and limestone deposits, (2) modes of handling and transporting immense tonnages of bulk material-coal and/or limestone, and (3) regional air-quality standards are some of the factors which will ultimately determine the demand for limestone. A discussion of these factors will be presented, with the intent of identifying geographic regions where significant increases in production can reasonably be expected.

Jan 1, 1974

By L. Vandamme, J. H. Curran

A fully three-dimensional hydraulic fracture propagation model, based on the Displacement Discontinuity Technique, is briefly described. Using this model, it is shown that the geometry of a propagating fracture is dependent on several factors, among which the fluid pressure distribution within the fracture plays an important role. The containment of hydraulic fractures is found to be dependent on stress and toughness barriers in the formation. Containment is also observed to be more effective with a decrease of the viscosity, pressure or flow rate of the injected fluid. The three-dimensional layout of the fracture is shown to have a definite influence on the width and pressure distributions within the fracture. The examples considered indicate the need for fully three-dimensional models, as complements to the commonly used two-dimensional and pseudo-three-dimensional models.

Jan 1, 1986

By Donald W. Gentry

Mine valuation is a multifaceted, interdisciplinary process by which the economic viability of an old, existing, or new mining property or venture is determined. The problems associated with arriving at a representative and accurate value for a mining property are complex and numerous, and the procedures utilized in determining these values vary from simple, back-of-envelope calculations to sophisticated mathematical manipulations requiring computer modeling and analysis. Regardless of the complexity or the degree of sophistication associated with any particular project, the evaluation process must ultimately provide management with two basic types of information. First, the evaluation process should indicate whether or not the mining project is economically viable after careful consideration of all engineering, environmental, geologic, and other variables pertaining to the project. Second, the evaluation process should provide management in- formation on the relative attractiveness of the project when compared to other alternatives. In some cases, it may be extremely difficult to supply this information for a project directly. Nonetheless, the evaluation process should and must present all information necessary in a format which can be incorporated into the decision-making process as expeditiously as possible.

Jan 1, 1979

By E. A. Metz

It has been approximately four years since the International Agency for Research on Cancer (IARC) reclassified crystalline silica as a "group one" substance. Since then, crystalline silica has been considered a human carcinogen. Silicosis is a preventable disease, and several aggressive campaigns have been developed to increase awareness of silica-dust-related problems in the industrial environment. New analytical techniques are now being developed to determine quantitatively the amount of crystalline silica in materials. Yet, still much is to be learned about the surface properties of silica and the way in which the disease progresses into full-blown silicosis. This paper discusses the interaction of free radicals generated by the mineral particles and lung tissue. It is the cell injury and DNA damage that progresses to fibrogenesis. Freshly fractured surfaces of silica contain free radicals. These free radicals play an important role in the stimulation of the alveolar macrophage and the development of the inflammatory reactions leading to the fibrotic response caused by silica. Engineers, scientists and physicians need to discuss the mineralogy of silica and the technical issues concerning the development of silicosis.

Jan 1, 2000

By R. J. Pugh

The surface chemical sites on several fillers (quartz, feldspar, calcite and granite) were studied by the adsorption of well defined acid and basic probe molecules (benzoic acid, benzyl alcohol, ethyl benzoate, pyridine and benzyl amine) from cyclohexane. The results provided a wide variation of adsorption data, emphasizing the extensive range of site heterogeneity on the filler surfaces. In addition, it was shown that the acidic probes were strongly adsorbed on all of the minerals, thus indicating that the basic surface sites dominate the acidic ones. Also, through FTIR studies with vapor-phase probes adsorbed on orthoclase, it was possible to identify the nature of specific sites and the type of bonding occurring between the filler surface and the probe molecule. These types of surface analytical techniques could give useful information for predicting the adsorption functional groups on dispersants, dyes, thickeners, etc. and could lead to enhanced interfacial bonding between the filler and the matrix.

Jan 1, 1993

By Ning Liu, Xuming Wang, Yongqiang Lu, Jan D. Miller

Bench-scale flotation experiments have been conducted to study the effect of nonionic polyethylene oxide (PEO) polymer surfactants on the flotation of Florida phosphate rock. It has been found that PEOs having a molecular weight from 1,200 to 8,000 are effective. Flotation results demonstrate that the addition of nonionic PEO has a favorable effect on phosphate flotation, especially on the flotation of coarse phosphate feed. At about the same collector level, phosphate recovery can be improved by 10-30% with PEO addition. The surface chemistry of phosphate flotation using the fatty acid/fuel oil/PEO system has also been studied to better understand the phenomena involved. The increase in phosphate recovery with PEO addition has been attributed to improved dispersion of fatty acid, which leads to better froth stability and a more hydrophobic surface state.

Jan 1, 1999

By Kent S. Roessler

The Bureau of Mines is currently investigating the geophysical application of Tomography to monitor leachate during in-situ mining. Determining the location of the leachate is important for both economic and environmental reasons. By analyzing a sequence of tomographic images, we can determine where highly permeable/fractured regions are located and hence, major flow paths. Since BOMTOM (Bureau Of Mines TOMography - Tomographic Reconstruction Program), and BOMCRATR (Bureau Of Mines Curved RAy Tomography - Tomographic Reconstruction Program) are sensitive to user-selected ray path arrival times, we are also investigating the use of neural networks to automate the process of recognizing this feature. This paper presents a technique for detecting fracture zones and their orientations in a region between two boreholes, by using a motion analysis study of a sequence of tomographic images. It also addresses the need for an automated/unbiased method to pick crosshole seismic arrival times using a trained neural network. In exploration geophysics, the picking of first break arrivals represents a pattern recognition task. The neural net paradigm has proved to be a good method of solving this type of task. To pick the first arrival peak of a trace, the network is trained with a set of known (user selected) first arrival peaks by creating a binary image of a set of traces. Once trained, the neural net correctly picked first arrivals of the remaining traces in the set.

Jan 1, 1992