Search Documents

The US economy grew at a rate of 4% in 1994 and the gross domestic product rose to $6.74 trillion. With 261 million people - 605,000 in mining, including petroleum -the United States has l 10 million dwelling units and 200 million licensed motor vehicles. New private housing units authorized in 1994 rose 14% to 1.4 million units. New car production rose 11 % to 6.6 million units, while truck and bus production rose 30% to 5.2 million units. The inflation rate was less than 3% and the prime rate of interest averaged 7.15%. The producer price index (1982 = 100) for fuels and related products and power was down 4% to 78, while metals and metal products rose 5% to 125. Chemicals and allied products rose 3% to 132, and non-metallic mineral products rose 3% to 124. The merchandise trade deficit rose 25% to $166 billion. Disorder in the former Soviet Union led to substantial dumping of mineral materials. With vast mineral resources, the former Soviet Union land area totaled 22.4 million km2 (8.6 million sq miles). In comparison, the North Ameri¬can Free Trade Agreement (NAFTA) area (United States, Canada and Mexico) totals 21.4 million km2 (8.3 million sq miles).

Jan 1, 1995

By Malcolm Reeves

The heavy oil reservoirs of Alberta and Saskatchewan include sequences of unconeolidated silts and fine sands which respond in an unusual manner when subjected to the high temperature and pore-fluid-pressure associated with steam injection and other thermal enhanced recovery techniques. Apparent transient connections are suddenly established between producers and injectore and there is an associated enhancement in oil (and sand) production. These phenomena have been attributed to local fluidization and piping processes which are known to occur in situations where high pore-fluid-pressures prevent the mobilization of intergranular friction. These breakdown processes may be associated with the penetration of tongues of the heated reservoir fluids with suspended sand into the creep sensitive intact reservoir since the viscosity ratios are sufficiently high for viscous fingering instability of the fluid-fluid interface. A program of laboratory tests has been carried out to measure the strength characteristic of saturated oil sands at a variety of temperatures and fluid pressures. These tests suggest, that in common with the coarser Athabasca sands, the Waseca sands have very little cohesive strength and show the characteristic dilational failure response of dense sands. Some special tests, devised to determine the relative ease with which samples can be fluidized, confirm the expected susceptibility of the fine- sand silts. Both piping and fluidization can be readily induced at in-situ reservoir temperatures and pressures. Analysis of stresses around wellbores suggests that fluid-pressure gradients may be sufficient to initiate piping and that backward erosion along streamlines may link producers and injectors. Such pipes may act as well “adits” gathering oil from the heated reservoir and contributing to enhanced production rates. Mechanical breakdown of the reservoir by drilling, injection and production processes provides a consistent possible explanation for the sand-cut response of production wells.

Jan 1, 1986

By B Faulkner, M. Weinecke

In 1997, Sveciala began a program to develop a process to convert waste tires into valuable commodities. A review of numerous approaches revealed shortcomings that were process related or mechanical related, while some of the approaches emphasized he production of low-value products. A market study revealed that a process that could produce a good grade of carbon black would be economically feasible. This paper discusses the laboratory and pilot-plant development and commercial plant design of such a process.

Jan 1, 2002

By Michael G. Li

Prediction of acid rock drainage (ARD) for low-sulphide, low-neutralisation potential (LSLNP) mine wastes is methodologically different from that for normal sulphidic mining wastes. In this paper. LSLNP wastes are conveniently defined as those with S2 < 1% and ABA-NP2 < 20 kg CaCO3 eq/t. The distinctiveness of ARD prediction for LSLNP materials originates from their frequently low oxidation rates and is mainly attributable to two reasons. First, the utilisation efficiency of available carbonate neutralisation potential (CNP2) rapidly deteriorates when the sulphide oxidation rate per unit mass of waste drops below a certain level. Reducing the flushing rate of a waste has the same effect as increasing the oxidation rate. Second, silicate neutralisation becomes increasingly important as oxidation rates diminish, and can no longer be ignored in LSLNP materials as it often is for normal sulphidic mine wastes. In this paper, the effects of oxidation rate, pore gas CO2 partial pressure, and flushing rate on ARD prediction for LSLNP materials are theoretically demonstrated with the help of modelling using the computer program MINTEQA2. A new methodology for ARD prediction for LSLNP materials is presented in terms of a prediction procedure. Finally, a case study is given to validate some of theoretical aspects discussed and to illustrate the use of the newly proposed ARD prediction procedure.

Jan 1, 2000

By Donald L. King, Frank A. Baczek

Sedimentation-based equipment is used in applications where separation of solids from liquid by gravity settling is desired. If a concentrated solids slurry is desired, the equipment is designed to "thicken"; if a clear liquid is desired the equipment is designed to "clarify." Thickeners normally handle higher solids loading rates than clarifiers, which usually process feed slurries containing low concentrations of suspended solids. Thickeners are therefore designed for heavier-duty requirements, and clarifiers have extra features to ensure more complete suspended solids removal. Major components (Figure 1) that are common to all sedimentation-based equipment are: tank, drive-support structure, drive unit and lifting device, rake structure, feed well, and a means of overflow and underflow withdrawal. Specific features are designed interdependently after the overall separation approach is defined conceptually. This conceptual approach is usually based on past experience or evolves from sedimentation studies conducted on samples of the slurry to be handled. Because many variations and combinations of components are possible, the overall conceptual approach has a number of possible designs that will accomplish the desired results. The final choice is based on practicality, potential for minimizing upsets, and cost.

Jan 1, 1986

By Frank Palkovits

All technologies move through a cycle from infancy to maturity. Thickened tailings have moved into the young adulthood phase of its development. Many mining companies like the idea of reducing their water-taking and water disposal issues. This limits the risks associated with traditional surface water-covered tailings facilities and the reduced dilution possible through underground disposal of thickened or paste tailings. Just as home theater systems advertised as ?plug and play? are rarely quite that straightforward, implementing and improving a thickened-tailings system has its challenges. However, the technology has also developed in recent years so it is more accessible. Some success factors have emerged because of the new technologies. Is thickened tailings the right solution? The first step in success with thickened tailings should be whether it is, in fact, the right solution for a particular mine. And, if so, what type of thickening is best. The answer depends on several factors, including: ? Grain size: The grain size that is optimal for maximizing mill recovery is some-times not suitable for thickening. Other mineralogical factors, such as mica content, may also influence whether the tailings are suitable. ? Water issues: Available water does not always have the purity necessary for the process. Another issue to consider is that if water is in short supply, as is increasingly often the case, thickening may be a way to reduce the need to both take and dispose of water.

Jan 1, 2008

By Adam Levy, Thomas Novak, Sampurna Arya, Joseph Sottile, Kozo Saito

The use of a woven wire-mesh screen as part of a flooded-bed dust-scrubbing system is very popular in the underground coal mining industry. It is used in combination with a demister (mist eliminator) to remove dust from the dust-laden air. A study was conducted to measure the pressure drop across a flooded-bed wire-mesh screen at different airflow rates in onephase (dry) and two-phase (wet) conditions. Two empirical relationships between pressure drop and air velocity were developed for dry and wet conditions, respectively. In both cases, the form of the empirical relationships was found to be similar to relationships given by Sabri Ergun for high velocity non-Darcy single and multi-phase flow through porous media. The experiments were repeated on a reduced-scale model of the wire-mesh screen, and the pressure-velocity relationships obtained from the full-scale prototype experiments were tested. The test results show validation of the full-scale empirical formulas on the small-scale model with an insignificant variation. This paper presents the empirical equations for pressure drop across the wire-mesh screen in dry and wet conditions. Researchers can use these equations as a tool to predict total pressure drops for wire-mesh screens of different scale sizes.

By Adam Levy, Thomas Novak, Sampurna Arya, Joseph Sottile, Kozo Saito

The use of a woven wire-mesh screen as part of a flooded-bed dust-scrubbing system is very popular in the underground coal mining industry. It is used in combination with a demister (mist eliminator) to remove dust from the dust-laden air. A study was conducted to measure the pressure drop across a flooded-bed wire-mesh screen at different airflow rates in onephase (dry) and two-phase (wet) conditions. Two empirical relationships between pressure drop and air velocity were developed for dry and wet conditions, respectively. In both cases, the form of the empirical relationships was found to be similar to relationships given by Sabri Ergun for high velocity non-Darcy single and multi-phase flow through porous media. The experiments were repeated on a reduced-scale model of the wire-mesh screen, and the pressure-velocity relationships obtained from the full-scale prototype experiments were tested. The test results show validation of the full-scale empirical formulas on the small-scale model with an insignificant variation. This paper presents the empirical equations for pressure drop across the wire-mesh screen in dry and wet conditions. Researchers can use these equations as a tool to predict total pressure drops for wire-mesh screens of different scale sizes.

By R. M. Williams

Introduction Ring roller mills are efficient size reduction machines embodying the following machine functions: 1) Size Reduction: from a feed size of 2 in. to various size products as fine as 400 mesh, or granulation from 2 in. to 6 mesh containing a minimum of fines. 2) Drying: fluid bed drying of wet feed materials. 3) Conveying: negative pressure air system results in dust-free conveying. 4) Beneficiation: liberation and removal of foreign materials from the auxiliary bottom discharge simultaneously while grinding. Operation Operation of the roller mill system, Figs. 78 and 79, is completely automatic. A feeder introduces raw material into the grinding chamber in the base of the roller mill at a rate determined by pressure variations within the roller mill as material is ground and air conveyed away. The feeder will be activated by the reduced static pressure and introduce unground material into the system, thereby maintaining a constant differential pressure. Plows located ahead of each grinding roll direct the material upward and between the grinding rolls and the bull ring where it is ground to size. The grinding rolls are free to swing out centrifugally, which forces them to bear upon and grind the raw material. Being free to pivot axially, the rolls automatically assume the proper position for grinding and need no adjustment to compensate for wear. Rotation of the rolls is by rolling contact. Once ground to size, material is swept out of the mill by the controlled air flow from the centrifugal main mill fan. Air suspended, the ground material passing through the adjustable spinner separator. In the separator, an accurate size classification is made which allows product-size material to be conveyed away from the roller mill while oversize material is returned internally for additional grinding. By varying the speed of the separator drive, more or less cyclonic action is achieved at this location, effectively controlling product size. Product sized material is removed from the airstream by the cyclone collector. Typically, a conveyor or product storage bin will be located to accept the product as it exits from the bottom of the cyclone collector.

Jan 1, 1985

By J. C. Yingling, R. Kumar, J. Sottile

The capability for on-line measurement of the quality characteristics of conveyed coal now enables mine operators to take advantage of the inherent heterogeneity of those streams and split them into wash and no-wash stocks. Relative to processing the entire stream, this reduces the amount of coal that must be washed at the mine and, thereby reducing processing costs, recovery losses and refuse-genera¬tion levels. In this paper, new ap¬proaches for optimal control of the segregation process using time-se¬ries models and empirical distribu¬tions are presented and demon¬strated using field data.

Jan 1, 2000

By Nora M. Hutt, Kevin A. Morin

The Sobek humidity cell has been in use with minor modification for more than 30 years to determine bulk primary-mineral reaction rates. As a result, it has become a key tool for predicting the bulk rate of sulphide oxidation, the Carbonate Mole Ratio (CMR) of neutralization-potential (NP) consumption to sulphide oxidation, and the rates of metal leaching. Most humidity cells are operated for less than a year, with the resulting rates extrapolated into the future for years or decades. The validity of these extrapolations was tested by examining longer trends from cells that have operated for three to seven years, as found in the International Kinetic Database (IKD). Additionally, large batches of cells for two minesites in the IKD (45 and 46 cells each) were examined to determine if regular, predictable trends were obtained across ranges of geochemistry at a minesite. The long-term cells show that the rates of sulphide oxidation and acid generation, based on sulphate production, have a 50% chance of stabilizing within one year, with the remainder fluctuating significantly throughout their test periods. Despite the fluctuations, the CMR, which is critical for defining site-specific or rock-unit-specific ABA criteria, remains relatively steady in many cases between 1.0 and 2.0 as expected from principles of aqueous geochemistry. However, if the sulphate-production rate falls below 10-30 mg/kg/wk, the CMR value can increase significantly. At and below these low rates, physical factors like flow rates of surface waters and groundwaters will determine the rate of NP consumption, rather than geochemical factors. Also, if weekly rinse pH falls to acidic values, the CMR will decrease below 1 .O, reflecting the exhaustion of fast- neutralizing minerals. The two batches of multiple cells also confirm these trends across arange of geochemistry. The long-term cells show that copper leaching often stabilizes within a narrow range as long as rinse pH remains relatively constant. Also, there is no strong dependence of leaching on the sulphate rate. However, the rate of copper production often increases sharply if rinse pH falls to acidic values. This suggests the measured copper-production rate in some cases is not a true primary rate, but a lower secondary rate after secondary- mineral precipitation within Sobek cells. As with the long-term cells, the batches of multiple cells show that copper production often increases gradually with decreasing rinse pH, with no clear dependence on sulphate production. However, high rates can also occur at near-neutral pH, so secondary-mineral precipitation of copper is not necessarily common.

Jan 1, 2000

By Leo J. Miller

Sulphur deposits occur within the upper Salado and Rustler gypsum beds. The formation of a sulphur ore deposit requires large quantities of oil and /or gas, which must find a permeable pathway into the gypsum beds. The Permian beds weathered for 90 million years in an arid environment prior to the advent of a more humid climate at the beginning of the Cretaceous Period. The first Cretaceous rivers enlarged the sinkholes and caverns of the Karstified Permian terrain and deposited coarse conglomerates and sands into the subsurface gypsum beds. The resulting network of caverns and sinkholes, filled with permeable sediments, permitted the free flow of hydrocarbons through gypsum. All sinkholes and caverns infilled with Cretaceous sediments that have penetrated beds of gypsum are associated with sulphur deposits. The Castile gypsum lies directly upon the oil bearing Bell Canyon formation. Sinkholes and caverns filled with Cretaceous sediments occur in the lower Castile. Biogenic calcite and sulphur are adjacent to these sediments. However, faults assume the major role in generating the initial permeability, allowing hydrocarbons to penetrate the lower Castile gypsum. The largest faults are associated with biogenic calcite and sulphur for a distance of 250 meters up from the bottom of the Castile gypsum. It is apparent that two dynamic geological processes are generating permeability within the gypsum beds: (1) the Cretaceous sands decending with difficulty into gypsum and (2) the faults creating permeability in the lower Castile but losing energy through soft bed deformation in the overlying gypsum. Both of these sulphur ore controls are mappable, but another large sulphur deposit of the magnitude of the Culberson Sulphur Mine has yet to be discovered. It appears that massive sulphur deposits are associated with the largest scale examples of each system, that is (1) high densities of deep sinkholes and separately

Jan 1, 1992

By Arun Patel, Diane Hirsch, Pamela Moran

The Metropolitan Washington Airports Authority (Authority) has undertaken a tremendous expansion of Washington Dulles International Airport in Fairfax, Virginia, including upgrading passenger transportation between concourses. The first stage of this expansion envisioned a shallow cut-and-cover pedestrian tunnel between the Main Terminal and Concourse B with associated vertical circulation structures. At the beginning of the design contract, the Authority’s consulting team of Earth Tech, formerly Kaiser Engineers, and the Dr. G. Sauer Corporation compared the cost and disruption of constructing the tunnel as a cut-and-cover structure to mining the tunnel using the New Austrian Tunneling Method (NATM). Upon review, the Authority endorsed the latter method.

Jan 1, 2003

By A. L. Mular

Introduction The cost of grinding may be divided into a fixed equipment cost portion and an operating cost portion. The fixed equipment cost is the amount of money required to purchase the grinding mill itself. This amount may be kept separate from the installation cost which, often, is taken as a percentage of the fixed equipment cost. A good average is 43%; therefore a $100,000 ball mill would cost approxi¬mately $143,000 installed. Operating costs are variable and paid per unit time for power, liner replacement, grinding charge replenishment, labor, and mainte¬nance including major parts replacement. Such costs depend on the geographical location and will vary with the cost of labor. Operating costs are difficult to estimate. Most mining companies consider such information proprietary. This section provides a means to obtain an estimate of the equip¬ment cost of a grinding mill with a rated accuracy of±l0%. Compara¬ble methods to determine operating costs are not available. Such costs are presented in table form with suggestions for updating them. Esti¬mating the cost of liners and steel replacement is possible as described in a later section. Capital Costs of Grinding Mills Grinding mill costs have been related,124 by means of equations and corresponding graphs, to the nominal horsepower requirements of mills. All graphs are based on a Marshall and Stevens cost index for Mining and Milling of 300, where a cost index is a ratio used to estimate current prices of equipment from obsolete prices. Where (Cost Index Now) Cost Now = (Cost Then) (Cost Index Then) (I) For example, the cost of an autogenous mill that requires a 3000¬hp motor is estimated as $500,000 (Fig. 95). This was the estimated price when the M&S (Marshall and Stevens, Mining and Milling) cost index had a value of 300. If the index is currently at 400, then the estimated current price of the autogenous mill is: Cost Now = ($500,000) (400) (300) = $667,000 Most professional journals will publish current values of cost indices at least once a month. In subsequent pages, each graph of grinding mill cost vs. mill horsepower has an associated graph of capacity vs. horsepower along with a table that relates mill size to horsepower. The associated graph and the table must be used with caution, since both apply to an average ore under average conditions. Example calculations showing how graphs should be used are shown in the following. It should be stressed that the cost data incorporated herein ex¬cludes the cost of pumps, motors, lines, and classifiers, unless other¬wise stated. Costs are not direct quotes; they are the averages of quotes supplied by manufacturers and analyzed by means of regression analysis. Example 1. Calculate the power required to grind 100 tons of dry solids per hour (in a closed circuit with a classifier) when the

Jan 1, 1985

By Mark E. Smith, Gerald J. Gierszewski

Introduction The purpose of this paper is to present a procedure used by the authors for evaluating and designing soil liner systems. This method is particularly valuable in evaluating various treatment schemes for chemically amended soil liners. A tabulation of laboratory test results on various soil types are presented to quantify the effectiveness of certain treatments. A typical liner design program includes developing and proving soil borrow sources, designing the cross-section of the liner system, developing construction specifications, and providing construction services to ensure the intended product is achieved. Material Source Development The first step in designing a soil liner is to identify and evaluate suitable borrow sources within an economical haulage range. This is best done in a two step approach: a reconnaissance level investigation to identify target areas and a detailed evaluation of those targets. Reconnaissance: The goal of the preliminary investigation is to locate potential borrow sources for liner quality soils. This includes all natural materials which can be compacted, chemically treated, or otherwise amended to yield an installed permeability at or below some target value. This requires utilization of all available data sources: Soil Conservation Service, BLM, aerial photos, USGS geologic maps, and project geologist records. The goal at this stage is to locate shallow deposits of favorable soil types. The Unified Soil Classification System provides an excellent first pass grouping. Clays, clayey sands and silts are the most favorable soil types, although silty sands and occasionally clayey gravels can make excellent liners, and are often amenable to chemical modification. The lowest permeabilities are generally achieved with CH, CL and MH soils. Once preliminary targets have been identified using visual examination, laboratory classification tests should be performed to further refine the selection. Testing at this stage should include gradation, plasticity and hydrometer analyses. Additionally, "preg-rob" testing should be done as early as practical. Preg-rob is a phenomenon where gold or silver ions in solution associate with the clay, or other, minerals. When this occurs, a portion of the gold or silver leached from the ore is actually tied-up by the clay and thus a reduces recovery. Testing for this consists of agitating a small sample of the soil in a solution containing dissolved gold or silver, preferably of similar chemical make-up as the solution which will contact the actual liner. The solution and soil are assayed before and after agitation to determine loss to the clay. A reliable estimate of the hydraulic conductivity, commonly referred to as permeability, can be developed from the D10 value by the use of Hezen&apos;s formula: K = 100 (D1012 This relationship is limited to soils where the finer particles do not move due to the force of flowing water (i.e.: "hydrodynamic stabilitym)(1). Additionally, the effect of platty particles on permeability is not as predictable as the effect of equidimensional particles. D10 is the sieve opening size at which 10% of the material is finer. Plasticity is also important from several standpoints. Constructability is directly related to plasticity. Very plastic clays and non-plastic silts both tend to be difficult soils, while medium plastic clays and clayey sands are generally very desirable. Post construction performance is also related to plasticity (e.g. swelling, shrinkage cracking, frost heave, etc.). Additionally, low plasticity silts and silty sands generally do not respond well to chemical amendment. Source Development: The result of the reconnaissance evaluation should be an estimate of the relative probability of developing a suitable borrow source within an economical haul distance. Of course, "economical distance" depends on the degree of handling and treatment the borrow material requires, as well as the cost of synthetic alternatives. The purpose of the detailed investigation is to prove out quantity and quality of material sources, and determine design parameters such as degree of compaction, mixing, treatment and thickness of liner. The emphasis of the testing program should be permeability and strength. Strength becomes increasingly important as the slope of the liner and the height of the heap increase. Permeability testing should evaluate the effects of compaction, water content, mixing and chemical treatment where appropriate. The effects compaction and water content during compaction have on

Jan 1, 1987

By C. Ostrowski, Z. Fajklewicz, K. Jakiel

Results of the application of the micro-gravity method in predicting rock bursts and rock mass deformations are discussed. Research was done in the Daisy black coal mine, Upper Silesia, Poland, during 1979-1980. At that time, microgravity investigations helped increase the safety of coalbed exploitation in progress. During the first stage of exploitation, a mining shock of 107 J energy was predicted in a region where 40 miners worked.

Jan 1, 1987

By Jack Garrity

The Asarco Mission Complex includes two milling operations around a large open-pit copper mine in southern Arizona. The ore body was discovered in 1953 and the complex has been in operation since 1959. The mills provide the concentration operations of crushing, grinding, flotation and filtering processes involved in processing copper ore. Smelting and other downstream processing are accomplished at other Asarco locations. The mine pays a smelting charge to the smelter, which is seen as a service to the concentrators. The higher the concentration of copper to the smelter, the lower the smelting charge is to the mine.

Jan 1, 1995

By S. L. Bolivar

The Prairie Creek intrusion, near Murfreesboro, AR, is the site of the most famous diamond mine in North America. Three major rock types are associated with the intrusion-a hypabyssal peridotite, a volcanic breccia in which the majority of diamonds occur, and tuft. Previous studies, including geological, geophysical, petrological, and whole-rock and mineral chemistry are reviewed. The recent suggestion, by other workers, that this intrusion may be more correctly called a lamproite is examined. This has serious implications for diamond exploration in Arkansas and elsewhere in the US.

Jan 1, 1987

By Yoginder P. Chugh

The Department of Energy is presently sponsoring the development of automated miner-bolter machines in an effort to increase production and productivity in the continuous room-and-pillar mining sections. This study is concerned with the production potential of these machines in three different mine layouts. The Underground Material Handling Simulation (UGMHS) computer model was utilized in the study. The effect of variables such as bolt installation delay, shuttle car capacity, and equipment availability on production are analyzed.

Jan 1, 1979

By R. Q. Honaker

Until recently, the application of the Jameson Cell technology in North America has been restricted to minerals processing. Recently, laboratory, pilot-plant and full-scale testing has been conducted to assess the Jameson Cell&apos;s ability to effectively treat fine coal. Based on the data, carrying-capacity relationships have been developed. In addition to its operational simplicity, the Jameson Cell has the ability to provide a separation efficiency near the theoretical separation performance on the basis of ash rejection while achieving a relatively high throughput capacity Tie results obtained from the various fine coal cleaning applications in North America is presented in this publication.

Jan 1, 1999