Search Documents

By Shane Yanagisawa

The Mineral Creek Diversion Project is at the Asarco Ray Mine Complex, about128 km (80 miles) east of Phoenix, Arizona. The new tunnel will intercept the waters of Mineral Creek about 2,134 m (7,000 ft) upstream from an existing tunnel. The 5.74 m(18.83 ft) hard rock TBM will break into the old tunnel about 2,162 m (7,090 ft) in from the old portal after mining 3,888 m (12,753 ft). The TBM will mine through a series of igneous and metamorphic formations including volcanic tuff, soft volcanic ash, massive diabase, fractured quartzite, and schist. The TBM will hole through into the existing 4.88 m (16 ft) dia. horseshoe tunnel where the TBM will be disassembled and removed from the tunnel.

Jan 1, 2001

By S. Atak, G. Bulut

The xanthate adsorption mechanism on pyrite was investigated with an emphasis on solubility studies. Additionally, adsorption studies, Eh and infrared spectrophotometer measurements were performed. Pyrite floats at pH levels between 3 and 6 using ethyl and amyl xanthates with a maximum at pH 4. The solubility of pyrite in the absence and presence of xanthate was investigated in detail with respect to pH and conditioning time. Experimental results showed that the solubility of pyrite increases from 60 to 120 ppm (10-3 to 2x10-3 mol/ L) in the presence of xanthate at pH 3. Fourier transform infrared (FTIR) spectra of ferric xanthate, dixanthogen and pyrite conditioned with xanthate indicated that dixanthogen is the only species that can be determined on the pyrite surface. Adsorption tests showed that the highest level of xanthate adsorption was in the acidic range; yet higher adsorption densities were detected in neutral solutions compared to alkaline conditions. Electrochemical data suggest that the doubling of the iron concentration is due to the reduction of ferric ion to ferrous by xanthate while xanthate is oxidized to dixanthogen. Dixanthogen formation together with the hydrophobic iron hydroxy-xanthate complex on the surface is proposed to be responsible for pyrite flotation. Key words: Flotation, Pyrite, Adsorption, Xanthate, Dixanthogen

Jan 1, 2003

By Gerrit V. R. Goodman, Fred N. Kissell

The issue of miner safety in case of an underground mine fire has been extensively examined by both government and industry. These efforts have intensified in recent years following a number of fatal fires at underground coal mines. As a result, there is an increasing interest in the reliability of coal mine escapeways during a mine fire. This paper discusses the use of fault tree analysis for evaluating escapeway reliability. A fault tree is developed using standard logic formulations. It is later evaluated using commercially available software. The computer model uses Boolean reduction to obtain the minimal cut sets and minimal path sets of the tree. A brief analysis is also conducted to determine the occurrence probability of the TOP event. This study shows that fault tree analysis is a viable means of analyzing escapeway reliability. The cut and path sets reveal those event sequences leading to fatalities. Such information is useful in safety training and accident prevention. The probability of the TOP event shows the frequency of occurrence for fatalities in an underground mine fire. The usefulness of this value, however, is limited by the accuracy of the data for the initiating events. For mining events, the data is difficult to estimate precisely.

Jan 1, 1989

By C. H. Lee, F. Concha, L. G. Austin, P. T. Luckie

The Concha-Almendra batch-settling treatment for concentrated suspensions of single-diameter spheres has been modified. This modified version is used in the differential equations of simple batch settling of a particle size range of different density materials. The equations have been programmed for a finite difference solution, and a number of test cases have been analyzed. By cutting the settling column at a fixed fractional height, the material below this height can be treated as underflow and the material above as overflow. The predicted partition curves obtained from treating the settling in this way have Sharpness Indices in the range of 0.5 to 0.6, in the absence of dispersion effects. The Sharpness Indices decrease as dispersion increases. When the feed size distributions are of the Rosin-Rammler form, the partition curves (corrected for the bypass fraction) fit the Rosin-Rammler equation with reasonable accuracy. The predicted Sharpness Index of a component of a mixture of two materials of different densities was unchanged from that of the same materials settled alone. However, for the same, feed size distribution and volume fraction of solids in the feed, the heavier material settled faster, and the lighter settled slower, than when settled alone.

Jan 1, 1993

By W. DR. Fritz

Technical progress depends on strategic objectives and a concept showing how to benefit from the effects of novel techniques in an innovation process and how to implement them creatively in harmony with manpower capabilities. With the invention of prime movers, it was initially power engineering which dominated the development of industrial history before it was replaced by production techniques resulting from the more widespread use of machines. With the advances in the field of data processing and with the introduction of novel communication techniques, it is information technology- which today is having an ever increasing impact on technological progress. The main objectives of information technology in this context are a positive influence on the ?time? factor as well as the provision of tools to handle the complexity governing many operational processes through a concentration of information for the decision-making process. The German hardcoal industry became aware of the chances inherent in these new technological possibilities for the optimization of operational sequences and of decision-making and planning processes as a potential for success at an early stage and it has worked out a purposeful concept for their implementation.

Jan 1, 1992

By V. T. McLemore

Rare earth elements (REE) are becoming more important in our society. REE deposits are found throughout NM. Some REE past production (1950s), as bastnaesite, came from the Gallinas Mountains district, Lincoln County, NM. Several companies and the U.S. Bureau of Mines (USBM) have conducted exploration programs to identify REE potential. Four types of deposits are found in the district: epithermal REE-F veins, Cu-REE-F veins, REE-F breccia pipe and iron skarn deposits; all are associated with Tertiary peraluminous, alkaline to alkalic-calcic volcanic rocks. District zonation is defined by base metals (REE-F-Cu veins) that form center of the district, surrounded by REE-F veins. The magmatic-hydrothermal breccia pipe deposits form a belt partially surrounding the veins. Iron skarns formed at the top and edge of the trachyte intrusion and are likely the earliest stage of mineralization. In 1991-1992, USBM calculated an inferred resource of 0.487 million metric tons with a grade of 2.95% total REE. With the projected increase in demand of REE, areas such as the Gallinas Mountains district in New Mexico are being re-examined for additional REE potential.

Jan 1, 2011

By Neil B. Prenn

Drill-hole contamination has been a problem for many years. Contamination of rotary drilling has been well documented. More recently contamination in wet reverse circulation drilling has been noted by Echo Bay and others at the 1991 AIME annual meeting. Mine Development Associates (MDA) has worked on a number of projects at which contamination of drill-hole samples has occurred. Properties are commonly acquired with drilling accomplished by other companies and at times the only records of the drilling program are the drill-hole logs and assays themselves. Identification of contaminated zones is sometimes difficult to determine. Most geologists and engineers in the industry are aware of the magnitude of the problem, as contamination is a relatively common problem with wet reverse circulation drilling. MDA has developed a computer program to help determine if contamination has occurred when using reverse circulation drilling, based on cumulative distribution curves and by a process we call decay analysis. Most deposits are not homogeneous throughout the deposit, but exhibit a characteristic drop-off or decay of assay values around higher-grade drill-hole intercepts. Using graphs of this characteristic decay and cumulative frequency distribution, we can use the program to help determine contamination in several ways. This paper will discuss the use of decay analysis at three gold deposits where contamination is known to have occurred. In one of the deposits decay analysis was used, successfully to determine if contamination had occurred, while in the other two the decay analysis was used to verify our decay analysis procedure.

Jan 1, 1992

By B. R. Reddy, P. V. R. Bhaskara Sarma

A process for the separation and recovery of cobalt and nickel was optimized for a sulfate leach solution of Indian Ocean sea nodules containing 80 g/m3 cobalt and 730 g/m3 nickel using the sodium salt of Cyanex 272 as the extractant. Extraction of both cobalt and nickel increased with an increase in equilibrium pH and extractant concentration. The extracted species with respect to cobalt appears to be CoA2.3HA. More than 99.6% extraction of cobalt was achieved using 0.04M solvent in a three-stage counter current simulation at the A:O phase ratio of 3:2. The co-extraction of nickel was about 0.6% only. Two-stage countercurrent stripping of cobalt from the loaded organic at an A:O ratio of 1: 7 resulted in a pregnant electrolyte enriched by 0.8 kg/m3, thus enabling a ten times overall enrichment of cobalt. From the cobalt free raffinate, nickel extraction was carried out using 0.25M solvent in two countercurrent stages, and the extraction showed a 99.8% recovery. Stripping of nickel from the loaded solvent was carried out at an equal phase ratio with the advance electrolyte of pH 1.75 in two countercurrent stages. The nickel stripping efficiency was found to be 98.8%. The present studies indicated that complete recovery of cobalt and nickel was possible using nine counter-current stages.

Jan 1, 2002

By Herbert H. Einstein, Edward C. Tse, David B. Ashley

INTRODUCTION Decision-making in the design and construction of underground facilities must be made under conditions of varying geologic uncertainty, uncertainty which can have a major cost impact if not properly regarded. Of the two approaches for dealing with this variability, preparing for the "worst" anticipated conditions and optimizing design and construction in-situ, preparing for the "worst" conditions is the more if not solely conventionally practiced method in the United States. While the conventional approach is recognized at times to be extremely overconservative, it will remain preferred until a more adaptable method is shown to be economically superior. This paper presents research aimed at providing just such answers as to when and if an adaptable tunnel design and construction approach is more cost effective than a non-adaptable one. To fully understand the characteristics of this choice between adaptable and conventional tunneling alternatives a summary discussion of adaptable methods is presented. An acknowledgement of the importance of geologic and other factor uncertainties in making this decision leads to the adoption of decision analysis as a quantitative methodology for formalizing the problem. Exercising this methodology on three prototypical tunneling scenarios--urban deep, urban shallow, and transmountain--allows an isolation and ranking of the most crucial factors in making the basic approach decision. One scenario, a transmountain highway tunnel, is carried further through a detailed probabilistic analysis to show under what conditions of varying uncertainty adaptable approaches possess economic advantages.

Jan 1, 1979

By E. Bane Kroeger

Plane failure in rock and soil slopes is usually caused by the intersection of a discontinuity plane with a slope face. Normally, these discontinuities are weaker than the surrounding intact rock and provide a surface along which movement can occur. The discontinuities are typically analyzed to determine the stability of a particular slope. One problem that arises when evaluating the stability of a planar feature is that the method for planar analysis is two-dimensional and has difficulty dealing with planes that are oblique to the slope face. Several researchers have stated in the past that planar failures are a special case of wedge failure. Wedge failures occur when two planar discontinuities intersect in an unfavorable manner. Sliding can occur along the intersection of the planes. Wedge failures are very common in rock slopes and can often be problematic. Wedge stability analysis methods are typically three-dimensional and can analyze planar features that are very oblique to the slope face. Wedge failure analysis can also be used to determine the stability of planar features with good success. One advantage to using wedge analysis over plane analysis is that a tension crack can be both non-vertical and oblique to the slope face in the wedge analysis. This allows the engineer to more closely match field conditions. It also negates the need for the engineer to have two separate software packages to analyze a single slope, saving both time and money.

Jan 1, 2002

By W. L. Cornell, F. W. Benn

The U.S. Bureau of Mines investigated froth flotation techniques to remove heavy metals (Pb, Cu, and Zn) from southeast Missouri lead mill tailings. It has been estimated that southeast Missouri contains between 200 and 300 million st of Pb tailings stored above ground. The tailings were classified as two distinct types: (1) pre- 1968 tailings from the Old Lead Belt (some more than 100 years old) and (2) post-1968 tailings from the New Lead Belt. The objectives of the investigation were to reduce the Pb remaining in the tailings to (500 ppm (<0.05% Pb) and to attempt to recover a marketable concentrate to offset a portion of the remediation costs. The remaining dolomite-limestone would then be used as mining backfill or agricultural limestone. Bench- scale froth flotation removed, in percent, 95 Pb, 84 Cu, and 54 Zn, leaving 94% of the original weight containing, in parts per million, 400 Pb, 40 Cu, and 300 Zn from the Old Lead Belt tailings. Separate flotation tests also removed, in percent, 85 Pb, 84 Cu, and 80 Zn, leaving 75% of the original weight containing, in parts per million, 400 Pb, 200 Cu, and 500 Zn from the New Lead Belt tailings . Concentrates recovered from the Old Lead Belt were retreated to produce a final Pb concentrate containing 72% Pb with a cleaner flotation recovery of 79%. Froth flotation proved to be a viable method to remove the heavy metals.

Jan 1, 1992

By T. J. Cox

The Red River is located within the Sangre De Cristo Mountain Range in northern New Mexico. An approximate 12-mile segment of the river from the town of Red River to the village of Questa (Questa) includes several hydrothermal alteration zones. Alteration ?scars? formed as a result of rapid chemical weathering and physical erosion of pyrite-rich hydrothermally altered rocks. Storm water runoff from the scar drainages contributes metal-laden, acidic water to the river and creates a visible plume of discolored water in the river. Acidic runoff reduces the river pH from 7 to the mid 3s for at least 2 hours during large storms and the low pH water continues downstream. Runoff from scar drainages increases some metal concentrations in the river from below chronic ecological criteria to as much as two orders of magnitude greater than acute ecological criteria, and results in acutely toxic conditions for macro-invertebrates. A general improvement in the river?s water quality occurs downstream due to dilution from tributary inflow from non-mineralized watersheds, the natural buffering capacity of the river, and storm water controls at the Chevron Mining Inc. Questa mine.

Jan 1, 2011

By Graham Swan, Richard K. Brummer

The paper begins by describing an underhand cut-and-fill mining concept for a 50m thick, generally tabular though irregularly shaped orebody dipping at 30 degrees and occurring at a depth of between 2300 and 2700m in the Sudbury Basin. From this, the broad design requirements of a fill system are stated. Two and three-dimensional numerical models are then described which were built to evaluate the theoretical benefits of different types of fill reinforcement. Included in this evaluation are the effects of span, fill strength, fill tightness, as well as static and dynamic loading types. Results, supported by large-scale physical models, are presented to show the significance of reinforcement on stable, undermined fill performance. Finally the paper describes work which has been done to evaluate the suitability of so-called silicated cemented backfill. This system is, in principal, attractive for deep mining applications since transportation is in the "safe" hydraulic regime, while fill water run-off, segregation and shrinkage effects are potentially eliminated in the stopes. The results from various surface and underground trial pours are reported which substantiate the proposed use of this type of backfill at depth.

Jan 1, 2001

By David M. Mchaina, Allan E. Hall, W. C. H. Kruining, Alan Coode, Stephen Hardcastle

This paper details an investigation into the feasibility of recirculating mine exhaust air in Saskatchewan potash mines. This project was initiated following a previous study at Ruttan Mine, Manitoba, which indicated that recirculation of exhaust air to reduce winter heating costs was feasible. The potash industry was selected for study because the mines use a minimum of blasting in their production methods and the exhaust temperature is significantly higher than that of most metal mines. These factors simplify the monitoring system required and have the potential for greater waste heat recovery. A series of measurements of underground mine pollutants was made at the main exhaust and intake shafts in order to determine the feasibility of introducing controlled recirculation of exhaust air. An experimental recirculation circuit was created by opening two existing doors situated between the return and intake shafts. During this recirculation trial, the air quality parameters at the intake, mixed intake and exhaust measuring stations were monitored. The results obtained from a questionnaire circulated to the regulatory agency and the major potash producers together with results obtained from underground field studies at Central Canada Potash (CCP) Division of Noranda Minerals indicated that controlled recirculation of mine exhaust air has potential application in these mines either to reduce heating costs and/ or to increase the face air quantities. A recirculation system is to be designed in conjunction with CCP and the Saskatchewan Ministry of Labour, Mine Safety Unit to attempt to implement a working recirculation system for CCP.

Jan 1, 1989

By Richard Keith Corbin

Canadian junior mining companies whose gold exploration and exploitation programs take them across the border into the western United States should be prepared to deal with the myriad of title issues involved in acquiring unpatented gold mining claims. The purpose of this paper is to serve as an introductory outline for Canadian junior mining companies to mining laws of the United States, as well as to relevant laws of some of the western gold mining states. Topics will include the five w&apos;s (who, where, what, why and when) of Canadian junior mining companies1 rights and responsibilities in acquiring interests in U.S. gold mining properties by claim staking, lease or purchase. Historic terms of common parlance among U.S. miners, such as "claimjumping" are defined and discussed. Various legal doctrines, such as "pedis possessio" and "good faith" in the location of claims are covered as well. Controversial subjects of contemporary interest are addressed in some detail, such as whether to locate a bulk-mineable disseminated gold deposit with placer claims or lode claims, and whether lodes may be staked over placers. By thus heightening the awareness of Canadian junior mining companies, it is hoped that they can be properly prepared to avoid title disputes, and to win lawsuits when they are unavoidable.

Jan 1, 1988

By B. Jensen, R. Davis, P. Golledge, A. D. S. Gillies, W. Urbanik Urbanik

A current program of research on the explosibility of coal dust/methane mixtures is described. During the study an explosion test chamber based on a novel design has been developed. This 20 litre open chamber uses a rotating drum concept for dust dispersion and infra-red sensors for dust concentration measurement. The chamber design allows different initiators to be tested while varying methane gas and coal dust concentrations. A new approach to the determination of coal dust concentration is included with a description of a dielectric dust probe. The measurement technique is based on the change in dielectric constant as the proportion of coal dust in air between probe capacitor plates increases or decreases. Characterization of coal dust samples is of vital importance. The particle size distribution, coal proximate analysis and elemental analysis were studied. Coal dust was sourced from airborne collected samples, settled dust from mine sources and seam channel samples crushed and sized. Explosibility test results indicate that a very low concentration of coal dust can form an explosible mixture when dispersed in methane concentration of just below five percent. With low temperature initiators, the coal dust lean limit concentration rises rapidly as the methane concentration is reduced. An accurate knowledge of the potential explosion hazards of coal dust and coal dust/methane mixture is necessary to establish safe operating conditions in underground mines. The research results outlined extend knowledge in this area.

Jan 1, 1989

By Jens Classen, Thomas Kurth, Karl G. Holter

High performance sprayed concrete equipment installed on two 9.4 m diameter hard rock TBMs enabled a continuous sprayed concrete lining for the entire contour in both tunnels to be performed concurrently with the advancing TBMs. Innovative layout of the sprayed concrete arrangements comprised ring beam constructions each with two independent spraying robots. Each of the spraying robots were independently connected to sprayed concrete pumps, as well as a high capacity concrete logistics system on the backup. The mix designs focused on long open-time, excellent pumpability and tough requirements on strength development. The achieved output capacities of the sprayed concrete amounts to an average of 15 m3 per hour. Peak capacities of 24 m3 per hour have been realized.

Jan 1, 2003

By Stefan Zanon, Ty Faechner, Clayton V. Deutsch

Secondary data are important in geostatistical simulation of continuous variables. Geophysical data and geological trends are used for modeling porosity and permeability. Multiple mineral grades must often be modeled for mining applications. Sequential Gaussian simulation (SGS) is often used because of its relative simplicity and robustness. The two most common approaches to integrate secondary data in Gaussian simulation are with (1) locally varying mean, or (2) collocated cokriging. A significant problem with both of these techniques is variance inflation, that is, the variance of the resulting simulated values is too high because of an inappropriate decision of stationarity or an artifact of choosing a single secondary data in presence of many. We introduce a self-healing procedure for dynamic correction of this problem. The dynamic correction is different for the locally varying mean approach and for collocated cokriging since there are different reasons why each of these methods causes variance inflation. The reasons for variance inflation are discussed and the self-healing is applied to a number of data sets.

Jan 1, 2002

By Donald J. Olson, Thomas J. Lutzenberger, John Ramage

The North Shore Inline Interceptor, Phase IA tunnel is a 8,550-meter (28,000-ft) interceptor tunnel currently being constructed by Traylor Bros./Frontier-Kemper, Joint Venture, using a 9.8-meter (32-ft - 4-in) diameter Robbins tunnel boring machine (TBM). This tunnel is being driven in Silurian age dolomite approximately 91.5 m (300 ft) below ground surface. Significant water inflows were encountered when the tunnel drive penetrated the thinly-bedded Waubakee Formation. Flow increases approaching 0.75 cu m per min per 30 m of tunnel (200 gpm per 100 ft) have occurred in this formation. After driving approximately 2,285 m (7,500 ft) of tunnel (200 m full face in the Waubakee Formation), total flows exceeded 12 cu m per min (3,200 gpm) with about 5.7 cu m per min (1,500 gpm) entering the tun¬nel from the 200 m (600 ft) of exposed Waubakee Formation. Additional water control measures consisting of increased pumping capacity, increased water treatment capacity, surface grouting ahead of the tunnel, grouting ahead of the tunnel face and panning to improve the working environment for installation of tunnel support, were implemented to deal with the large water inflows. Currently (January 24, 1989), 3,400 m (11,000 ft) of tunnel has been driven, total water inflows are in the range of 11.7 cu m per min (3,100 gpm) with only 6.8 cu m per min (1,800 gpm) inflow from about 1,220 m (4,000 ft) of tunnel driven full face through the Waubakee Formation.

Jan 1, 1989

By J. H. Tylczak, R. Blickensderfer

Impact and abrasion properties of various commercial US grinding halls were evaluated and compared by the Bureau of Mines, US Department of the Interior. Laboratory tests were conducted on balls obtained from eight major US manufacturers. The halls included forged steel, cast steel, and alloyed white cast iron and were subjected to repeated impacts until they broke or until 300,000 impacts were exceeded. Pin abrasion tests also were conducted. The results showed wide differences in impact lives, ranging from a few thousand to over 500,000 impacts. The life of inferior commercial halls was increased five to six times by a laboratory tempering heat treatment. For halls that did not break, the major impact wear mode was spalling and ranged from an average rate of 0.28 to 4.46 mg per impact. The softest halls (steel) had excellent impact resistance but low abrasion resistance. The abrasion resistance of the steel halls generally increased with hardness. The alloyed white cast irons had about twice the abrasion resistance of the steel halls. Users should become aware of the wide variations among commercial halls, and ball manufacturers should be aware that their product can he improved.

Jan 1, 1990