Search Documents

By Edmond O’Donovan

Mooranbah North is a new greenfield project in Australia's Bowen Basin that is projected to produce 4 mtpa of hard coking coal from a single longwall. Located in Central Queensland in Australia's northeast, this is one of Australia's main coal producing regions. From the outset, Mooranbah North's approach to equipment selection has differed markedly from that usually taken in the mining industry, and the conveyor industry in particular. Until recently, no performance requirements have been placed on conveyor equipment suppliers. This arose from a practice of purchasing components in an ad-hoc manner from a variety of sources, and the mine then configuring the system. More recently, single source supply has been adopted as a means of obtaining some performance guarantee, usually expressed in terms of system availability. Unfortunately, the term "availability" has a multitude of definitions, particularly in the underground coal sector. A conveyor availability of 98% is a common goal but this rarely means the conveyor must operate 165 hours/week, 52 weeks/year. There are mines that have one maintenance shift for each production shift and claim availability of 100%. What is meant is that no down time is logged to the conveyor during the hours that it is wanted. This "generous" definition of availability would not be tolerated in many industries and nor should it. Unfortunately, a true definition of availability, such as is applied to steam turbines in the power generation industry, is not particularly helpful. Five day/ week operations would immediately face a 28% penalty against 7 day rosters, and there would be no sensible manner in which weekend maintenance could be incorporated into the availability formula. The approach adopted by Mooranbah North was to specify a period of "Failure Free Operation," which would be followed by a maintenance period. This

Jan 1, 1998

By Henry R. Tiedemann, Eugene H. Skinner, George E. Wickham

The need for ground support research in underground excavation has been well identified in recent years by many studies in the subject area (1, 2, 3, 4, 5). A typical conclusion from these reports (1, 2) is that the drill-and-blast (D & B) mining or the mechanical tunnel boring machine (TBM) methods are expected to be continued in use for the needs of tunneling in the immediate future. The Organization for Economic Co-operation and Development (OECD) sponsored in June, 1970 advisory conferences on Hardrock and Soft Ground Tunneling (3,4). These two reports were based on the combined response received from approximately six hundred inquiries from 17 nations in the summer of 1969 and which concerned all aspects of present-day inadequacies of, and the needed improvements in the technology of tunneling. Some specific problem areas in ground support and tunnel linings were: 1) the ability to successfully predict rock loads that must be carried by the support system; and 2) inadequate methods for determining the load-carrying capacity of the various support systems. Therefore, the problem area is clearly defined by these two objectives: 1) To find means of predicting rock loads; and 2) To develop methodology for determining safe, efficient, and economical ground support design practices. Noting these research needs from a great number of sources, the United States Bureau of Mines, Spokane Mining Research Center (SMRC), acting as agent for the Advanced Research Projects Agency (ARPA), undertook contract research effort in these problem areas. Work by Jacobs Associates has studied a methodology for specification of temporary artificial support based on the dependent sequence of mining operations and prediction of various rock conditions in the pre-excavation stage. The major thesis is that rock behavior is the

Jan 1, 1997

By James R. Arnold

Gold Fields Mining Corporation started processing ore from it's Chimney Creek operation in northern Nevada in November, 1987. Since that time production has averaged about 200,000 ounces per year from the milling and dump leaching circuits combined. The events that led up to commissioning of the plant started in January of 1985 when the Gold Fields exploration team drilled their first hole in an area now known as Discovery Hill. The major orebody was located later in the year in what is currently the major focus of activity, the North Pit. Subsequent drilling since plant startup has found another 14 million tons of ore two miles south of the original orebody. This South Pit orebody is currently being stripped and metallurgical testing is underway. Engineering Engineering on the Chimney Creek plant started in earnest in May, 1986. Davy McKee Corporation from San Ramon, California, did both the engineering and the construction management. Before engineering began the entire senior staff of the Plant Department was hired and assigned to the project. Senior staff included the Plant Superintendent, Plant General Foreman, Maintenance General Foreman and Chief Metallurgist. Gold Fields does not employ an internal central engineering staff to design their plants. We feel that the people who design the plant should be the ones who will be required to run it once it has been commissioned. This philosophy affords a continuous accountability from start of design through commissioning and operations. All four of the senior staff spent the most critical phase of the engineering stage at Davy McKee, so the plant is truly a reflection of all four disciplines. In bringing on the Maintenance General Foreman from the start, there was a focus placed on ease of maintaining the plant. Another philosophy that was adopted from the start was that the plant be easy to work in and maintain for both operators and maintenance personnel. Numerous design criteria were given to Davy McKee to ensure this. For example, we required that every piece of equipment could be reached easily with a crane or fork lift. All conveyors were required to have walkways on both sides for ease of maintenance and a minimum of 30 inches of clearance under them for ease of cleanup. Visibility for operators was considered very important and the control rooms and general plant layout were designed with this in mind. A list of about 100 general rules were given to Davy McKee during the early layout meetings and these were held as the general design criteria throughout engineering and construction. While engineering was progressing in San Ramon, California, dump leach test work was being done at the site. Three 6 foot diameter fiberglass columns were constructed and filled to a 20 foot height with low grade ore. Leaching characteristics were determined and the dump leach design was based on information collected from these columns. Construction The major contractors on the project were The Industrial Company for the bulk of the piping and structural, EMKO on the electrical/ instrumentation and Hunewill for most of the earth work and leach pad construction. All plant operating and maintenance personnel were employed eight weeks before startup for intensive training. Instructors were Gold Fields personnel, including foremen, and Davy McKee engineers. On occasion, selected suppliers representatives were brought in to discuss major pieces of equipment. Project completion was targeted for January, 1988 at a projected cost of 78.9 million dollars. Actual startup was about 1 1/2 months ahead of schedule and slightly under budget. Full design capacity was achieved the first full month of operation. Crushing Run of mine ore is delivered to the crusher and dumped into a 90 ton hopper which is topped with a 30" X 30" opening stationary grizzly. Ore is fed to a 50" X 60" Telsmith jaw crusher with a 5' wide apron feeder. The closed size setting of the

Jan 1, 1989

By M. D. Dennis

Precious metal mineralization at Mt. Hamilton" Nevada is associated with a poly-metallic, garnet-pyroxene skarn system developed in middle to upper Cambrian calcareous shales, limestones and dolomites. The skarn is developed around the Cretaceous Seligman and Monte cristo calc-alkaline stocks. Gold is associated with intense retrograde alteration. Later epithermal quartz veins containing gold, silver, base-metal sulfides, and sulfosalts cross-cut skarn alteration. Westmont Mining Inc. is currently developing two mineralized zones containing a geologic resource of approximately 7.7 M.T., which averages 0.05 OPT gold and 0.5 OPT silver. The project will have an estimated mine life of seven years, with a planned annual production rate of 35,000 ounces of gold and 300,000 ounces of silver.

Jan 1, 1989

By T. Brasier, K. Oakes, S. Crabtree, B. Lusk

Destructive wave interference has been studied in theory for many years. In application however, limited information can be found. Recently, circumstances have enabled a multidisciplinary team to utilize electronic detonators and seismograph analysis to create destructive wave interference in an underground production blasting application. Springfield Underground, located in Springfield, MO, in conjunction with Orica, ETI, White Industrial Seismology, and the University of Missouri – Rolla has shown the ability to use destructive wave interference in underground blasting to reduce ground vibrations directly above. In order to develop additional reserves a reduction in vibration levels was necessary for tunneling under the Springfield Municipal Water Supply. The paper discusses the process by which the reduction in vibration was achieved in practice, as well as a technical explanation of the effects of destructive wave interference and sacrificial holes.

Jan 1, 2006

By J. Reyher, R. Bratton, G. Luttrell, B. Li

"Flotation is regarded as the best available method of upgrading minerals and coal fines. However, its efficiency deteriorates rapidly with decreasing particle size. Further, ultrafine concentrates are difficult to be dewatered economically, forcing companies to discard part of the ultrafine materials to impoundments. To overcome these problems, a new method of separating and simultaneously dewatering ultrafine particles has been developed. Following extensive laboratory-scale test work, the process, known as hydrophobic-hydrophilic separation (HHS), has been tested successfully in continuous operations at proof-of-concept (POC)- and pilot-scale tests. The results show that the HHS process is capable of producing high quality clean coal with high recoveries and low moistures. INTRODUCTION Coal preparation plants are designed with up to four parallel processing circuits for treating coarse (> 12 mm), intermediate (12x1 mm) small (1x0.15 mm), and fine (<0.15 mm) particles. The plus 0.15 mm fractions can be effectively cleaned efficiently with gravity separation methods (Wills, 2006). At present, the only commercially viable option for cleaning the finest fraction is froth flotation (Yoon et al., 1999). In flotation, air is dispersed in the form of small air bubbles in a tank in which coal fines are suspended. The small air bubbles selectively collect the hydrophobic coal particles and float to the surface, forming a froth phase which overflows into a launder. As is well known, ultrafine coal particles of less than 30-50 µm are difficult to be collected by the air bubbles, resulting in low recoveries. Furthermore, fine particle flotation suffers from low carrying capacities and poor selectivity due to entrainment problems. (Bethell et al., 2005; Luttrell et al., 2014). In addition, the froth products containing ultrafine coal are difficult to dewater. Mechanical dewatering in general becomes inefficient with decreasing particle size due to small cake porosity and high surface area, resulting in high moistures (Hucko et al., 1988). The cost often becomes prohibitive with particles of smaller than ~45 µm (Bethell et al., 2005). Moreover, the high-moisture products are difficult to handle and incur high shipping costs and lower thermal efficiencies (Honaker et al., 2013)"

Jan 1, 2016

By J. Ainsworth, W. Trudel, L. Schutz, C. L. Bolin

Newmont mine geologists have added substantial economic value developing over 1,150 tonnes into quality surface and underground gold reserves since 1986. However, the recent 5-year gold price slump from $387 to $262 per ounce has shifted mine geologists focus to optimizing open pit profitability and developing high-grade, high cash flow and low capital development underground reserves. More than $65 million projected revenue has been added to the Gold Quarry south layback following multi-departmental model reconciliation investigations. Kriged mine polygon construction, controlled blast heave and high-quality geologic advice in selective mining will have multi-million dollar beneficial impacts.

Jan 1, 2002

By D. A. Karvonen

Although the economy in the Province of Saskatchewan has historically been agriculturally oriented, a major new source of wealth has been realized through natural resources such as petroleum and natural gas, coal and uranium and since the 1960&apos;s - potash. Potash or potassium chloride, in the form in which it is presently produced in Saskatchewan is used primarily as fertilizer, a source of potassium, one of three essential elements required for healthy plant growth with about 5 percent of production sold to the chemical industry for use in such products as soap and liquid detergent, glass and ceramics, textiles and some pharmaceuticals. Saskatchewan is estimated to have approximately 40 percent of known world potash reserves and its ten active mines account for some 25% of annual world production. The development of this resource was recognized to be important to the development of Saskathcewan. In an effort to guarantee a fair and lasting economic benefit to the Province of Saskatchewan the Potash Corporation of Saskatchewan (PCS) was created on February 4, 1975 through an Order-in-Council under the Crown Corporation&apos;s Act and later on April 1, 1976, the Potash Corporation Act provided for its continuation. PCS was given the mandate to acquire ownership of a significant portion of the potash mining capacity in Saskatchewan and to establish an organization capable of operating the facilities, marketing the product and conducting all of the other activities necessary for a successful corporation competing in the world potash industry.

Jan 1, 1983

By Jr. Mason

Eminent Domain is the power of the government or municipality to take property for public use without the consent or acceptance of the owner. Typically the agency taking the property will make an offer on the property, hoping that the owner will immediately accept and allow work to begin. If a mutual resolution regarding the property value cannot be reached, however, the municipality will condemn the premises and institute a condemnation action in a court of law, which is when the problems begin. The power of the government to take the subject property is limited by the Federal and State constitutional duty to pay "just compensation" for the property.

Jan 1, 1989

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"Underground refuge alternatives (RAs) require an air source to supply breathable air to the occupants. This requires pressure relief valves (PRVs) to prevent unsafe pressures from building up within the RA. The Mine Safety and Health Administration (MSHA) mandates that PRVs prevent pressure from exceeding 1.25 kPa (0.18 psi or 5 in H2O), or as specified by the manufacturer, above mine atmospheric pressure when a fan or compressor is used for the air supply. Research to date by the National Institute for Occupational Safety and Health (NIOSH) suggests that the design and implementation of PRVs used in RAs has not yet had sufficient performance analysis or technical development. In response to this need, NIOSH tested a variety of PRVs using an instrumented test fixture consisting of data acquisition equipment, a centrifugal blower, ductwork, and various sensors to determine if subject PRVs meet the MSHA requirement. Relief pressures and flow characteristics including opening pressure and flow rate were measured for five different PRVs under a variety of conditions. Subject PRVs included two off-the-shelf modified check valves, two check valves used in MSHA-approved built-in-place (BIP) RAs, and a commercially available valve that was designed for a steel RA and is currently being used in some BIP RAs. The test results showed relief pressures ranging from 0.20 to 1.53 kPa (0.8 to 6.1 in H2O) and flow rates up to 19.3 m3/min (683 SCFM). INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and mine safety standards enforcement [1]. Section 13 of the MINER Act specifically directed NIOSH to provide for research into the effectiveness and viability of refuge alternatives (RAs) for underground coal mines. This mandate culminated in the 2009 adoption of changes to 30 CFR mining health and safety regulations, requiring underground coal mines to provide mine emergency RAs and associated components, to provide a life-sustaining environment for persons trapped underground. Such RAs can be either self-contained mobile units or built-in-place (BIP) facilities. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe breathable atmosphere under positive pressure within the RAs. One specific criterion for maintaining a safe RA atmosphere requires the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (0.18 psi or 5.0 in. H2O), or at a pressure above mine atmospheric pressure in the RA as specified by the manufacturer when the breathable air is supplied by a fan or compressor [2]."

Jan 1, 2017

By A. H. Summers

The La Choya mine is located 55 km south of Sonoyta in northwestern Sonora, Mexico. Mineralization is controlled by a 40 meter thick thrust fault zone which created a permeable host for the metal-bearing hydrothermal solutions. The ore body is mined by open pit using wheel loaders and truck haulage. Gold and silver are recovered from low grade ore by heap leaching followed by carbon adsorption.

Jan 1, 1997

By Steven W. Hunt, Gregory C. Baker, Glen J. Rorison

Microtunneling methods were utilized beneath pile-supported clarifier basins to replace settlement damaged sludge drain lines at the Jones Island Wastewater Treatment Plant in Milwaukee, Wisconsin. To minimize the risk of blockage and expensive recovery of a microtunnel boring machine against pipe piles or construction debris, a Soltau RVS 80 was utilized. This machine allowed the alignment to be initially bored with guided 114-mm diameter rods to ensure proper alignment and lack of obstructions. Casing pipe was then installed by jacking 1-m long, 305-mm diameterclay pipe along the rods and behind an auger head. This case history also discusses how 2.4-m diameter precast concrete pipe was used as a one-pass sinking caisson for workshafts and new cleanout manholes.

Jan 1, 2001

By D. L. Kuck

Water ice pillars far underground mine roof support can be frozen and/or maintained and/or melted on demand. The system to do this consists of a refrigeration brine chiller, brine circulation system and disposable plastic containers. Fusion expansion, resilience to dynamic loads, plastic deformation under stress, and non-contamination of coal or ore are unique properties of ice. Lower labor and material costs are economic advantages of ice far mine structural support. Ice brattices can become ice pillars on retreat. For safety, ice pillars can be placed (by remote control, if necessary) in hazardous sites without human entry.

Jan 1, 1988

By C. J. Konya

When blasts are designed, the assumption is made that all blastholes release near ideal energy. In many types of mining operations, some blastholes release very little useful energy. These blastholes will be called malfunctioning blastholes. Recent studies indicate that on many types of blasting applications, 30 percent of blastholes are malfunctioning. This malfunctioning routinely occurs on the operation and is not an unusual occurrence. This paper will discuss the cause of malfunctioning blastholes and methods to minimize the detrimental effect on both safety and costs.

Jan 1, 1988

By Michael Chender

The rapid and continuing expansion of computer and communication capability is giving birth to profound changes in the business environment. Some commentators hold that the basis of the world economy has already shifted from industry to information. Regardless of the overall implications of these changes, it is now clear that every company potentially has both access to and a need for much more information for decision making than was the case a few years ago. The importance of information to the mining industry has been underlined by the rash of unexpected economic and political developments and by the accompanying market volatility that have marked the past decade. It should be abundantly clear to even the smallest mine operator that the price for his output can be instantly affected by unexpected developments halfway across the world. Nevertheless, many mining companies still are much less sophisticated about information than they might be. For many, the historical feeling that information is an unnecessary luxury for a production-oriented business still seems to linger. On the other hand, the overwhelming volume of source material, uncertainty as to its accuracy, and the problems of finding relevant material when needed, presents stumbling blocks to viable systems of information management. Introduction When a company needs certain information, it has two basic alternatives. It can either research and develop the information in-house or pay for someone else to do it. Few mining companies have the in-house capability to assemble information needed for careful planning. On the other hand, companies often engage consultants to find information that is in fact easily accessible. All too often companies give up on procuring needed information because of the frustration of not being able to find it, and of not wanting to pay seemingly exorbitant sums for someone else to produce it. The result is poor planning. This article addresses two aspects of the information problem-finding the right sources and then accessing the particular information desired, especially as it pertains to nonferrous metal exploration and development issues. In the first section, major English-language sources that report on exploration and development (excluding primary sources of geological information, such as technical journals) are discussed.* In the second section, some available techniques for efficiently accessing this information are presented, focusing on the new MINESEARCH database system. Part One: The Information Following the News The most obvious way to follow exploration and mining developments from a distance is through regular mining media. Many active mining districts have local newspapers, usually published in the district&apos;s major towns, that give extensive coverage to miningrelated activities. For instance, to follow activities in Idaho&apos;s Coeur d&apos;Alene silver district, one might subscribe to the Kellogg Wardner News and/or the Wallace Miner. Similarly, one might get the Sacramento Bee for news of current mining developments in north-central California. The American Metal Market, published in New York, is the daily newspaper that covers the metals industry as a whole, both in the US and abroad. Its coverage is weighted towards the refining, manufacturing, and consumption end of the business, but it frequently carries stories on mining activity, company dealings, and market outlooks. For news of major mining companies, the daily Wall Street Journal provides occasional coverage of North American companies, while the Financial Times of London serves as probably the best single source for worldwide company information. International Coverage There are three metals industry weeklies that have broad international coverage and readership. These are Metal Week, Metal Bulletin, and Mining Journal. Each has its strengths. Metals Week, a McGraw-Hill newsletter, focuses primarily on news of the metals markets, concentrating on those developments that are seen to most directly affect the price of nonferrous metals. Metals Week is strongest on North American news. Metal Bulletin, published in London, is particularly strong on

Jan 4, 1983

By Andrew Neale

ERIC GUTIERREZ: With that, we&apos;ll go ahead with the final speaker of the day, Andrew Neale. Andrew has a master&apos;s of science degree in mineral processing from the University of Alberta. He worked at the Falconbridge in Sudbury area, also at Brenda Mines, and then he became part of the Brenda Process Technology group in British Columbia. He joined Freeport in late 1993 in Indonesia, and was involved in process control and automation. He is now the senior manager of metallurgy in New Orleans. He&apos;s responsible for designing Freeport&apos;s new 100,000-ton-per-day expansion concentrator, which is currently being commissioned. Please welcome Andrew. ANDREW NEALE: With the ongoing explosion in digital computing power, there seems to be no limit to what can be modeled, simulated, and controlled in the mineral processing plant. However, at each stage of development of a control system, it is necessary to complete a cost-benefit analysis for justifying the move to a higher level of control. Incremental improvements in plant performance, while often significant, must be weighed against the costs of implementation and long-term maintenance. This presentation will provide examples of what the author believes are misplaced or misguided process control efforts and make a case for the KISS principle as applied to process control.

Jan 1, 1998

By R. J. Sweigard

Fine coal refuse is often pumped, as slurry, into surface impoundments as a means of permanent disposal. As the available volume is filled, the height of the embankments are frequently increased. Many times the additional embankment material is placed upon consolidated fine coal refuse. There has been some concern about the long-term effect of consolidation of this material at or above the liquid limit upon its shear strength. A laboratory investigation was performed using three different types of fine coal slurry taken from Central Appalachian coal preparation plants. The refuse was consolidated in 10-foot plexiglass columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart and triaxial tests were performed on both the consolidated material and unconsolidated material for comparison of their shear strength parameters.

Jan 1, 1997

By Morgan M. Sears

In recent years, one large mine collapse and numerous smaller bump events have resulted in a renewed interest in coal bump research. With numerical modeling, the Energy Release Rate (ERR) calculation quantifies the ?release? of the gravitational potential energy of the rock mass into the environment as mining progresses. This release of energy can occur passively in the form of heat and sound or dynamically in the form of pillar bumps or rock bursts. From the initial application of a calculated energy release rate in the deep hard-rock mines of South Africa, the ERR was found to have a significant correlation with the risk or potential of damaging coal bumps or rock bursts. In this research, an ERR calculation is incorporated into the modern LaModel program to facilitate the analysis for potential coal bumps. Initially the ERR calculations in LaModel are verified using a case study of cut sequences originally modeled using the MULSIM/NL program. Then, the ERR calculations are applied to a bump-prone mine in Southern Appalachia were a number of different pillar recovery cut sequences were used in order to minimize the risk of bumps.

Jan 1, 2009

By M. E. Poad

In 1986, a cooperative effort by the Homestake Mining company, the U.S. Bureau of Mines and the University of Utah was initiated to determine shaft stability while recovering high grade ore in a nearby pillar. Premining finite element simulations indicated the shaft would remain in elastic ground. Six years have elapsed and, despite some initial concern during the first lifts, it appears that the bulk of the original reserve will be safely and profitably recovered. An integrated application of rock mechanics tools from laboratory testing through numerical modelling to mine measurements and observations contributed substantially to the operational success of the project.

Jan 1, 1994

By J. H. Calder, J. C. Hower

Three lithotypes of Phalen coal from Cape Breton County, Nova Scotia, Canada, were subjected to a modified Hardgrove grindability index (HGI) test. The testing scheme differed from conventional (ASTM D-409) Hardgrove testing by, in one case, repeating the test three times prior to removing the -200-mesh fine coal from the Hardgrove mill, and, in a second test, removing fines after each of three successive Hardgrove tests. Only the first stage of the latter testing scheme actually conforms to the standard HGI test. All processed samples were analyzed petrographically by a combined maceral/microlithotype analysis. The increase in the percentage of coal ground to -200 mesh increases through the 60- to 180-mesh fractions for each of the lithotypes for the following two apparent reasons. First, with progressive grinding, more of the oversize material is close to 200 mesh (75 µm), creating a "pool" of particles ready to be ground to -200 mesh, and, second, the removal of fines from the system at each step eases the grinding at the successive step. The fines retained system shows the influence of buffering of further grinding by the particles retained in the grinding mill. The Phalen lithotypes and the series of Central Appalachian coals, evaluated previously by Hower and Wild (1994), differ in that an increase in vitrite and a decrease in trimacerite is observed in successive -200-mesh fractions in two of the Phalen lithotypes. This is the opposite of the trend observed in the slightly lower-rank Central Appalachian coals.

Jan 1, 1998