Search Documents

By Marvin Barnes

The Sacaton mine is a relatively new open¬pit copper mine owned by Asarco, Inc., which has been in production only a few years. The mineral deposits consist of two ore zones; a western, near-surface zone minable by open-pit methods, and a deeper eastern zone which will have to be mined underground, probably by block caving. The copper deposits are related to small quartz monzonite intrusives implaced into Precambrian granites. Both rock types act as hosts for the copper mineralization, which has been secondarily enriched sufficiently to constitute ore. In the western zone the enriched supergene chalcocite has been subjected to postenrichment oxidation processes with partial destruction of the chalcocite blanket. The deeper eastern chalcocite zone has not been as severely affected by later supergene processes. Several mineralogical populations are represented in the total copper deposit. Leached capping overlies the chalcocite enriched zone, and in the western ore body there is a very irregular interface between the leached and enriched zone, which is complicated by oxide copper minerals irregularly distributed. Primary lower-grade chalcopyrite mineralization occurs below the enriched zone. When mining commenced near the top of the enriched zone, considerable difficulty was encountered in correlating the actual grade of ore in place with the estimated grade of the mining blocks. The mineralogical complexity and fairly wide spacing of diamond drilling made reliable grade estimation of individual ore blocks a difficult procedure.

Jan 1, 1979

By O. H. Tuovinen, T. M. Bhatti

Microbiological leaching has been used as an alternative approach to conventional hydrometallurgical methods of uranium extraction. In the microbiological leaching process, iron-oxidizing bacteria oxidize pyritic phases to ferric iron and sulfuric acid, and uranium is solubilized from the ore due to sulfuric acid attack. If uranium in the ore material is in the reduced, tetravalent form (UIV), a red ox reaction is involved whereby uranium is oxidized to the hexavalent form (UvI) upon dissolution. In acid-leaching systems, the primary oxidant is ferric iron, which is reduced to ferrous iron by its chemical reaction with UIV. The ferrous iron thus formed is reoxidized to ferric iron by iron-oxidizing bacteria such as Thiobacillus ferrooxidans and Leptospirillum ferrooxidans. Nutritional requirements and responses to environmental extremes of acidophilic iron-oxidizing bacteria are appraised. The S-entity in Fe-sulfides is oxidized to sulfate by bacteria similar to Thiobacillus ferrooxidans and Thiobacillus thiooxidans. Pyrite and marcasite oxidation is a sulfuric acid forming reaction. Heap, dump and in situ leach techniques are feasible as bacterial leaching systems.

Jan 1, 2000

By J. S. Stachulak

Inco Limited operates nine underground mines on the rim of the Sudbury Basin. These operations are situated near the City of Sudbury, 589 km (365 miles) west of Montreal, and 363 km (225 miles) north of Toronto. The ores are mined primarily for nickel and copper, and the principal minerals are pentlandite, chalcopyrite, and pyrrhotite. Total ore production from underground is in excess of 51,000 tons per day. The total volume of fresh air supplied to the nine mines is six million cubic feet per minute. There are 50 main fans in operation at these mines, powered by electric motors totalling 11,200 kw (15,000 hp). The trend in metal mining during recent years towards mechanization and high-tonnage production methods has greatly increased ventilation requirements. The flow of air must quickly dilute and carry away diesel exhaust fumes, dust created by mining operations, and the fumes of the explosives used in blasting. Mechanical ventilation is required to obtain the necessary volume and control, as natural ventilation pressures alone are, for the most part, inadequate and unreliable. In the event of a mine fire or other needs, close control of ventilation is essential. There are two unique heating systems presently in operation at Inco: Creighton Natural Heat Ex- changer and Stobie Ice Stopes.

Jan 1, 1989

By M. Karmis

Surface subsidence has been recognized as an inevitable consequence of underground coal mining for several centuries. The damage resulting from this phenomenon has been witnessed in rural as well as in urban areas and ranges from simple land settlement to severe structural damage to buildings. Subsidence prevention is not feasible, at least under the existing technological and economic constraints of underground coal mining. Using a rational method of subsidence prediction, it has been demonstrated in many coalfields that subsidence control can be successfully practiced in order to reduce and accommodate subsidence within environmentally acceptable levels. This paper presents the development and testing of a subsidence model, based on the zone area method. This technique is a refined development of the influence functions and it is capable of investigating a mining plan of any shape, thus facilitating both longwall and room-and-pillar mining systems. More specifically, this study can be divided into two major efforts: (a) The development of the zone area model. This formulation was designed to accommodate the analysis of an optimum number of zones, over the area of interest, both accurately and efficiently. (b) The testing of the computer techniques with appropriate field measurements. In order to accomplish this, published as well as unpublished information was collected and analyzed according to a regionalized scheme. This procedure minimized differences in subsidence characteristics between the various coalfields and allowed a regional validation of the predictive capabilities of the model.

Jan 1, 1982

By G. Pan

A geostatistical approach is proposed for the design of infill drilling programs. The method consists of the following four major steps: developing geological favorability models, delineating mineralization and ore envelopes, classifying resource potentials, and designing infill drilling patterns. Geological modeling develops the permissible geological zones in which infill drilling is designed. Modeling mineralization and ore envelopes establishes criteria on the potential blocks to be drilled. The blocks that are included within the ore envelopes are considered in the infill drilling. The following four types of resource potentials are used in this analysis: measured, indicated, possible and barren. Blocks in the indicated category are the top targets to be confirmed in infill drilling. Blocks of possible resources may be considered exploration targets. The algorithms involved in the analysis include indicator favorability analysis, indicator kriging and ordinary kriging. A case study on a gold deposit of the Carlin type is presented to demonstrate the methodology. The deposit was originally delineated by a sparse drilling program with about 230ft of average spacing. The infill drilling design, based on the new method, suggests a significant reduction on the number of holes from a regular-grid infill drilling pattern.

Jan 1, 1996

By A. F. Alsobrook

Specialty silica materials, as defined in this chapter, are rocks that consist predominantly of silica (SiO2) and are produced as chunks, round pebbles, and sawed or trimmed blocks and other shapes for nonconstruction applications. The rock types include quartzite, sandstone, novaculite, flint, chert, and vein quartz. Other terms used commercially include jasper, silex, lascas, and rock crystal. In its publication, Minerals Yearbook, the US Bureau of Mines (USBM) reports the production and consumption of some specialty silica materials under several headings. Quartzite, sandstone, and novaculite used in abrasive applications are addressed by the USBM under Abrasive Materials. Lascas, a type of vein quartz used in growing synthetic quartz crystals and in fusing applications, is discussed under Quartz Crystal. Silica gravel used in manufacturing silicon metal and ferrosilicon, as metallurgical fluxstone, and as a filtration medium is covered under Industrial Sand and Gravel. Information on

Jan 1, 1994

By III Feeley

The U.S. Department of Energy is supporting the engineering development of three advanced physical coal cleaning technologies--selective agglomeration, advanced flotation, and advanced cycloning--capable of significantly reducing the pyritic-sulfur content of U. S. coals. The objective of this activity is to provide the coal production and electric-utility industries with a cost-effective option for addressing the SO2 emission reductions required by the 1990 Clean Air Act Amendments. A secondary objective is to evaluate the potential of advanced coal cleaning for removing trace elements that are precursors to the formation of hazardous air pollutants. This paper will summarize the status of the three advanced physical coal cleaning engineering development projects.

Jan 1, 1993

By G. Lodewijks

Today most belt conveyors used for the transportation of bulk solid materials are driven in a centralized way with all drives in one location. The dynamics of these systems has been studied since the early seventies of the previous century and are well understood. Compared to the more conventional belt conveyor system with a centralized drive station positioned at the head and/or tail of the system, a decentralized driven layout with drive stations distributed along the whole length of the belt offers a number of advantages. However, to make a decentralized driven configuration a good alternative to a centralized driven, the system designer will have to balance these benefits with the increased complexity. The full potential of a decentralized driven system can only be realized if the right balance is found between the locally applied drive force and the motion resistances occurring along the system. From previous research it was found that in a multiple driven belt conveyor system the most dominant belt behavior occurs in the belt section between the tensioning device and the first drive station. In this paper different possibilities are analyzed to improve this dominant belt response and optimize the starting behavior. This can be accomplished by changing the predescribed start up profile, starting the drive stations in sequence rather then all at the same time and altering the locations of the drive stations.

Jan 1, 2008

By Ronny J. Sadri

Under contract to the Department of Energy, Fluor Mining & Metals, Inc. and Bonner & Moore Associates developed a group of computer models that can be used to simulate single seam dragline operations. These models have been subsequently modified by Fluor for use in multi-seam dragline mining situations. The single seam model analyzes the digging, spoiling, and walking patterns of draglines to identify possible parameter changes to increase productivity. Parameters such as key-cutting, panel width, digout length, and bench height, etc., are analyzed in this process. The models were tested using data from four operating mines. Field demonstrations were performed to correlate computer optimization results with field data. Productivity was greatly enhanced at one mine site by a change in some of the operating parameters. The multi-seam study has as its objective the development of a broad- based mine planning tool which would be used to identify and quantify the different procedures employed in multi-seam dragline mines to increase their productivity. The major problem identified in multi-seam mining is the sequencing of the different stripping and mining operations. The multi-seam model has the same capabilities as the single seam model. In addition, it models up to four seams with three partings per seam. It allows the operation of several draglines at different levels, and analyzes the effect of ramps, rehandling, and ancillary mining equipment.

Jan 1, 1982

By T. R. von Ow

The method of powering mills such as AG, SAG and Ball has a long and technically interesting history. It can be said that almost every decade in the last half century had its own trend. The trends were dominated by the market demand, the advanced process development and requirement of the mechanical and the electrical technology but mostly by the price of the applied technology. The increasing size of the ring geared mills in the last years requires more awareness on the drive train solution. Special attention must be paid to the mechanics and the requirements of the power grid. Operational challenges such as soft starting and controlled operation as well as the protection of the equipment have gained importance. Frequency converter drive solutions dedicated to single or dual pinion ring-geared mills offer significant advantages over conventional drives due to their application specific features and controls. Solutions with low speed motors as well as high speed motors cover all possible configurations available for ring geared mills.

Jan 1, 2010

By Bernard J. Scheiner, R. J. Wesely, Cy E. Jordan, A. D. Zunkel, Gary M. Wilemon

The U.S. Bureau of Mines has investigated leaching of off-grade western United States phosphate deposits using sulfuric acid (H2SO4) in the presence of methanol. A combination of ore grinding followed by sulfuric acid in methanol leaching extracted over 80 pct of the phosphate. This leaching technique significantly limited the dissolution of iron, aluminum, and magnesium impurities and produced a phosphoric acid that was well within the desired limits for these impurities. The dissolution rate of phosphate rock in the sulfuric acid methanol system was significantly slower than the conventional aqueous sulfuric acid dissolution. Initially dissolution of the phosphate particle was controlled by the amount of surface area available to the sulfuric acid reactant. After about an hour of leaching, phosphate dissolution was slowed almost to a stop, limited by the rate of ion diffusion through the calcium sulfate barrier layer surrounding the unreacted phosphate particle. Consequently, the ore was ground below 38-pm to increase the particle surface area available and improve the overall dissolution kinetics and extraction. In addition, the sulfuric acid was slowly metered into the reactor to prevent any excess heat from the mixing of acid with the methanol from simulating the formation of methyl sulfates. The formation of methyl sulfate ultimately lowered the overall phosphate extraction by exhausting the supply of available sulfate ions for the dissolution reaction. Subsequent evaporation of the methanol from the product acid decomposed the methyl sulfates leaving undesirable sulfate ions in the product acid. Slow acid addition to the reactor provided high phosphate extraction and limited the amount of sulfate in the final product acid.

Jan 1, 1993

A general form of pore pressure in a saturated porous medium, which is subject to external forces it has the pressurization of a borehole in hydraulic fracturing, is derived. The pore pressure consists of two parts: the preexisting initial pore pressure and the pressure induced by fluid flow due to the pressure difference caused by pressurizing the borehole The initial pore pressure associates with the effective stresses in the stress, fields of crustal stresses and a thick hollow cylinder subjected to internal and external pressures. The pure pressure weaned by fluid flow is implied in Biot's (1941) constitutive equation for three-dimensional consolidation and proved to be the exact effective pore pressure (Nur and Byerlee, 1971). Using this general form of pore pressure, a general poroelastic model for hydraulic-fracturing breakdown (fracture-initiation) pressure was derived. This model was validated by laboratory experimental results on Indiana limestone. Three sets of tests were conducted under the conditions of preexisting pore pressures of 6, 21 and 28 MPa, respectively. The equal horizontal (confining) pressures applied in the tests ranged from 6 to 60 MPa. Hainison and Fairhurst's (1967) model appear to be applicable to rocks having microcracks or flows. Experimental results of fracture reopening pressures on Indiana limestone supported this assertion. The test results also demonstrated that, when the pressure difference between the confining and the initial pore pressure grows larger than 14 to 21 MPa, the breakdown pressures agree well with the general poroelastic model developed in this paper. This indicates that the developed model will be superior when hydrofacturing stress measurements are conducted at great depth.

Jan 1, 1997

By Victor F. Hollister

Porphyry copper deposits can be categorized into three models for purposes of prospect evaluation: Breccia-pipe, modified Lowell and Guilbert, and diorite models. The modified Lowell and Guilbert model is normally associated with a quartz-bearing intrusive and a potassic, phyllic, argillic, and propylitic alteration sequence. Variations can occur in the alteration zones of this model that range from orthoclase-rich (Kalamazoo, Silver Bell, and Mineral Park) to ortho- clase-deficient (Petaquilla and Bougainville) potassic zones. The unifying features of the model are the presence of a phyllic zone and a quartz-bearing intrusion. The breccia-pipe model (Toquepala) is characterized by structure and alteration related to or controlled by breccia. Where tourmaline occurs in the breccia, the identity of the model is usually clear. However, if tourmaline is not commonly developed in the breccia (La Caridad), the deposit can be misidentified as to model. Porphyry copper deposits associated with quartz-deficient intrusives, whether these are calc-alkalic diorites or alkalic plutons, are characterized by alteration suites distinct from those of the modified Lowell and Guilbert model. These have been generalized as diorite model porphyry deposits. Because alteration and mineralogical development in diorite model deposits is distinct from that of the modified Lowell and Guilbert, ore guides and exploration tactics differ for the two models. The reprint that follows describing the three prospecting models summarizes their features. It is to be emphasized that these are models used in exploration for specific deposit types and are not genetic, tectonic, or geographic models. Porphyry copper deposits can be metamorphosed. Gibralter is an example of a Lowell and Guilbert model deposit that has undergone regional metamorphism.

Jan 1, 1991

By Roderick G. Eggert, John E. Tilton

During much of the 1970s and 1980s, world metal consumption grew more slowly than during the 19505 and 1960s. The slowdown contributed to surplus capacity and low real prices because actual consumption was consistently less than expected as new mining and mineral processing capacity came on stream. Over the last year or so, however, world metal consumption has picked up noticeably, raising the question, Has metal demand returned to the long-run growth rates more typical of the 1950s and 1960s than of the 1970s and 1980s? This paper examines this possibility and, more generally, assesses the factors that will shape demand for the major metals over the longer term. TRENDS IN METAL CONSUMPTION The extent to which metal consumption has recaptured the brisk growth rates typical of the 1950s, 1960s, and early 1970s is shown in Figure 1. This figure traces the consumption of crude steel, primary aluminum, refined copper, refined lead, and refined zinc between 1960 and 1987 for the western world, consisting of the OECD countries (including the United States), and the developing countries. Consumption increased in 1987 for all five metals, and preliminary data for the first six months of 1988 suggest even more substantial increases, at least for the United States (U.S. Bureau of Mines, 1988). However, Figure 1 also shows that the recent increases in consumption are not untypical of similar surges during earlier periods of economic expansion and thus may reflect only cyclical or temporary factors. In short, the available data are unable to provide a clear indication of whether recent increases in metal consumption reflect the beginning of a new era of faster growth or simply a cyclical and temporary upturn associated with the expansionary phase of the business cycle. Consequently, to pursue this issue, we are forced to examine the underlying forces that will shape metal demand trends over the next decade. The approach we have taken involves two steps. The first examines the prospects for overall economic growth. The expectation is, the faster the economy expands, the faster the production of metal-containing goods grows.2

Jan 1, 1989

By Paul C. Miclea

With the growing urban population and the concern for traffic congestion and pollution (emissions control), public transportation is becoming more and more attractive to both city dwellers and managers. To gain access to the central area of the city, the sub- way remains the most viable alternative, despite its higher cost when compared to above ground or elevated transportation systems. There are relatively few regulations and criteria for subway ventilation, particularly when compared with mine ventilation. The main document that provides guidance and general recommendations for subway ventilation and environmental control is the Sub- way Environmental Design Handbook, published in 1976 (2nd edition) by the U.S. Department of Transportation, Office of Re- search and Development. Many of the subway systems in existence today have been designed and built with ventilation features adequate for normal train operation, but their design does not consider stringent criteria for such emergency conditions as a train fire in a tunnel. The National Fire Protection Association's Standard for Fixed Guideway Transit Systems known as NFPA 130 as well as the ASHRAE Handbook - HVAC Applications (1995) provide specific design and operation requirements for subway ventilation systems. Some of the existing, old subways are upgrading their ventilation systems to comply with the new regulations. The ability of a particular ventilation system design to provide adequate ventilation during normal and emergency conditions can be evaluated using computer modeling and simulation techniques. A train fire will cause a sudden change in the tunnel ventilation pattern by adding an unsteady and fast-growing source of heat. The hot air and gasses created by a fire will tend to flow uphill, possibly against the normal flow, producing a 'backlayering effect." To prevent this effect from happening, enough ventilation must be provided and the governing criterion to establish the required airflow is called 'Critical Velocity." Several software packages are available for special applications on tunnel and station ventilation as well as to model the spread of smoke and heat in case of a major tunnel fire, using Computational Fluid Dynamics. This paper presents the current issues in subway ventilation, as shared by the public transit community around the world, together with modern alternative design concepts vis-à-vis the more stringent emerging Fire-Life Safety criteria. Examples of recent studies and ventilation systems design are provided.

Jan 1, 1997

By M. Fofana

The use of a laboratory-scale magnetic fluid-based separator for coal separations was examined. A Frantz laboratory magnetic separator was modified by fabricating new pole pieces of the appropriate geometry to provide the proper magnetic field gradients. Two separation chambers, which were constructed out of Plexiglas, were designed to fit between the pole pieces. A commercially available, water-based, ferro-magnetic fluid was used as the separating medium. The separating density was changed by varying the intensity of the electromagnet. Both batch and continuous separations were made using 0.59x0.50 and 0.18x0.15 mm coal. The results are compared to those obtained using organic liquids.

Jan 1, 1996

By Ian H. Clark

A series of numerical experiments were performed in order to elucidate the stress distribution, fracture strength and mineral liberation potential in single specimens of rock during crushing. Fracture strength was shown to reduce under eccentric loading conditions. Similarly, the presence of inclusions, both hard and soft, reduced the fracture strength. The predicted crack paths indicate that mineral liberation is unlikely to be preferential.

Jan 1, 1992

A new fluid bed lime calcining plant is converting high quality limestone into quicklime at the Cape Lime facility in Vredendal, South Africa. The plant was supplied by Metso Minerals. Cape Lime, established in 1946, operates two limestone and dolomite mines in South Africa. The high quality Vredendal limestone deposits are suitable for the production of lime for water treatment and for manufacturing precipitated calcium carbonate.

Jan 1, 2003

By Gerald P. Kelton

Hydrocyclones have emerged as successful classification devices In closed circuit grinding applications However, their use for ultrafine particles separation is a relatively new application For ultrafine particles separation In small diameter (51 mm or smaller) cyclones, the cyclone diameter, feed pulp density or viscosity, pressure drop, and configuration play an important role Most often commercial application of the small diameter cyclones suffers from plugging problems resulting from the presence of fibres, wood chips, paper scraps, etc This paper describes important design features of small cyclones, followed by examples of case studies of commercial application of these cyclones

Jan 1, 1983

By B. Bringhurst, J. J. McClelland

A filter consisting of a synthetic fibrous material has been determined to be a viable alternative to the wire mesh panels currently used in irrigated filter dust collection systems. An extensive laboratory investigation of the material showed that it removed a higher percentage of both respirable coal and quartz dust from the air entering a collector than did the flat and pleated wire mesh panel designs. This improvement in dust collection efficiency reduced the amount of coal and quartz dust discharged from the collector exhaust by approximately 44%. Since continued exposure to excessive levels (>5%) of respirable quartz dust presents a severe health hazard, this alternative filter medium could be of use to those mines required to comply with more stringent dust standards due to quartz.

Jan 1, 1992