Search Documents

By T. Negeri, A. O. Orumwense

Microwave pretreatment is one of the emerging technologies which have been reported as having potential economic benefits for the processing of amenable ores. The application of microwave pretreatment to the processing of refractory and finely disseminated ores is of great interest as the technology can potentially reduce high comminution costs and improve mineral liberation. Sized ore samples were subjected to microwave irradiation at power levels varying from 1 to 5 kW over exposure times of between 1 and 6minutes in order to determine the influence of heating rate on mineral transformation, ground product size distribution and mineral liberation. The microwave irradiated samples were ground and subsequently floated. A comparison is made with non-microwave treated samples. Flotation grade and recovery show a strong dependence on the microwave absorption characteristics of the mineral components of the ore, in the following decreasing order -sphalerite, galena, and lastly chalcopyrite.

Jan 1, 2003

By D. H. Carlson, J. H. Johnson, C. F. Renders

Research was conducted at a western coal mine on a wide variety of underground mining vehicles to develop testing procedures for portable instrumentation monitoring of tailpipe concentrations of diesel particulate matter (DPM), carbon dioxide (CO2) carbon monoxide (CO) and nitric oxide (NO). DPM was measured using the Emissions Measurement Appa¬ratus (EMA) developed by Michigan Technological University (MTU), and an ECOM-KL five-gas analyzer was used to measure gaseous tailpipe concentrations. Baseline concentrations of the tailpipe pollutants were measured using vehicle systems to load the engine. Concentrations before and after the water scrubber were measured and water scrubber efficiencies were estimated by calculation. Field measurement procedures were established. Heavy-duty vehicles with automatic transmissions were loaded using the torque converter to stall the engine. Consistent engine loading for light-duty vehicles with manual transmissions involved placing the transmission in neutral and adjusting the throttle to maintain a constant engine speed of 2,500 rpm. Tailpipe CO2 concentrations for Caterpillar 3306 and 3304 engines were compared to laboratory CO2 data from Caterpillar and MSHA to help determine if engine settings were correctly adjusted for operation at high altitudes. (Perfect agreement between the mine vehicle tailpipe and laboratory measurements would not be expected because of the differences in the test conditions.) DPM concentrations for light-duty vehicles ranged from about 20 to 160 mg/m3, and one light-duty vehicle averaged near 1,000 mg/m3. DPM concentrations for heavy-duty vehicles ranged from about 55 to 200 mg/m3. Widely ranging DPM concentrations for a particular vehicle type reflect the state of maintenance, fuel rate settings and different engine loading procedures as well as differences between samples collected upstream and downstream of the waterscrubber. The calculated DPM removal efficiencies due to the water scrubber varied considerably between vehicles, ranging from 13% to 51%. Calculations indicate that, under worst-case conditions, very large reductions in DPM may be required to meet the proposed DPM PEL of 0.15 mg/m3, even on vehicles with water scrubbers. In-mine ambient air studies, which are needed to actually measure the impact of the tailpipe concentrations on the work environment and the effect of mine ventilation on the dilution of DPM were not done in this first set of tests.

Jan 1, 2000

By Francis S. Kendorski

INTRODUCTION Drift design problems in caving operations are a re¬sult of the geologic factors contributing to the overall success of the system, of the engineering factors dictated by economic and technical considerations, and of ore production practices. Combining these factors, a rational underground sup¬port system of rock reinforcement, light steel channel section or welded wire fabric, and shotcrete can be de¬signed based on rock fracturing, rock load, abutment loadings, ground movement, expected repair and desired flexibility. The design concept uses the effect achieved by restraining, reinforcing, and maintaining some of the intrinsic strength of the fractured rock mass composed of interlocked blocks of intact rock and rock fractures. Three different examples of drift support design in hypo¬thetical mines using the caving system are given. Caving is a system of underground mining where ore is extracted by means of gravity after the ore body is allowed to fail by removing support from underneath. The rock mass of the ore body fractures and flows ver¬tically downward to let gravity do as much work as pos¬sible. Caving differs from many other mining systems in that blasting is used only to initiate the rock mass failure by removing the rock supporting the ore but not to break the ore itself. The initial movement of the rock mass dur¬ing failure and the consequent crushing and grinding during the continued movement serve to reduce the ore to particles of a manageable size, with only limited sec¬ondary blasting necessary. The broken ore is extracted from the bottom of the failed rock mass through funnels of some sort pre-excavated in the rock. Ore extraction must continue or the swell of the broken rock will even¬tually fill the cavity and stop further rock mass failure and movement. The excellent general discussion on block caving in the SME Mining Engineering Handbook (Julin and Tobie, 1973) adequately covers the principles and application of this type of underground mining. Many rock mechanics aspects of block caving have been covered by others (McMahon and Kendrick, 1969; Swaisgood, et al., 1972; Mahtab and Dixon, 1975; King, 1946) and will not be reviewed further. Maintaining the stability of production drifts is one of the most troublesome problems plaguing the mine manager in a caving operation. Many factors contrib¬ute to drift support problems, and identifying the causes of instability and producing a reasonable support design are two steps toward achieving stability consistent with the mine plan. This chapter sets forth a technique for the design of support systems for production drifts in caving opera¬tions. The basic support system elements employed are rock reinforcement, welded wire fabric, and shotcrete. Recognized as contributing to the design are the factors of rock load, additional load from mining activity, rock fracture characteristics, repair expected, and flexibility. It must be emphasized that the drift must first be stabilized as for a tunnel, and the additional strengthen¬ing for mining-induced loads cannot contribute to the initial premining stabilization, or the reserve of strength is used up. MINE PLANNING The efficient mine planning engineer not only must satisfy the economic, human, and environmental aspects of his task but must also consider the mechanical con¬sequences of his plan. The problems created for the mine by placing parallel drifts too close, by crossing drifts on different levels with inadequate, if any, separa¬tion, and by installing connections and crossovers in the haulage plan without regard for the effective spans cre¬ated, are only a few of the problems a mine planning engineer can create for himself and the mine. The effect on immediately adjacent mine areas when an area is caved is important to drift design because the removal of vertical support from a rock mass causes the weight of that rock mass to be shifted elsewhere. The adjacent rock mass will carry this load and reach a new equilibrium with the applied stress. The advancing front of stress increase that results from caving (and many other mining systems) is generally called the abutment load and is the increase in stress over the gravity or tec¬tonic stress that already exists, as shown in Fig. 1. In general, the abutment load will be similar in nature to the stress change found around an opening in rock and will be taken as causing an increase in the vertical prin¬cipal stress, due to an approaching caving boundary, so that

Jan 1, 1982

By Armine F. Banfield

Selection of a plant site is becoming increasingly more difficult and important, mainly due to advances in technology, antipollution laws and changing economic, social and community conditions. Discussion falls naturally under three headings: economic considerations, terrain considerations and environmental considerations. Aside from acquisition of surface rights, problems having to do with terrain, or topography, usually can be dealt with by management alone. Economic considerations largely involve decision-making by management plus negotiations with government regulatory agencies acting under set rules. Environmental considerations, such as air and water pollution, townsites, housing, schools, noise abatement, appearance, surface rehabilitation and the like usually are under the control of federal, state or municipal bodies with a large degree of decision-making. Successful solution of environmental problems often requires lengthy negotiations, during which public relations by the mining company play an important part. Existing union regulations or customs may confine decision- making and the establishment of wage rates, working conditions and regulations. These usually require considerable planning and negotiation. Initial production often is delayed by formal negotiations involving environmental considerations. Surface facilities usually can be divided into two broad categories: those for concentrating ores--such as gold, silver, base metals, low-grade iron ore and potash-which should be close to the mine to reduce ore-transportation costs to a minimum, and those where the ore is shipped elsewhere for treatment, such as direct-shipping iron ores, complex high-value ores requiring specialized treatment and ores from which special products are derived for local markets. The long-term aspects of plant-site selection too often are given no or insufficient consideration because of immediate financial limitations. As a result, additional capital expenditures may be required later for relocation of townsites, roads, railroads and plants to provide additional room for extension of open-pit operations, tailings disposal, storage, or danger to foundations through underground subsidence or open-pit mining. In the past, hillside sites for concentrating plants were preferred to take advantage of gravity-feed methods The modern trend, however, is to place as much equipment as possible on approximately the same level. Some costs relating to plant sites are included in this section. They are ranges as of the year 1970, and are offered only as general guides. Such costs will vary widely with geographical location and, of course, are subject to escalation due to increases in wage rates and cost of materials. Items in the bibliography contain more detailed and comprehensive data on specific subjects. Most contain bibliographies of their own.

Jan 1, 1973

By Jerry Solomon

The subjects to be examined in my portion of the session entitled "Technology of Aluminum.. Recovery" will be twofold. 1. Economics of the basic aluminum economy--supply-demand-price. 2. Specifications of aluminum products produced from municipal waste--from the secondary aluminum standpoint. It is the object of this speech to first impress everyone with the excellent long-run markets for the aluminum products from municipal waste and then to acquaint everyone with the rather liberal scrap specifications that the recycling industry can tolerate. The most important statement that can be made about the recycling of aluminum is that it is now and will be an economic necessity. This is true far many reasons; one which hit the headlines recently was Interior Secretary Rogers Morton's statement "Third-world nations could use mineral wealth not to achieve political ends but to jack up economic positions. The result could be sky-rocketing prices and dwindling supplies on world markets." There is no reason why the group of countries that supplies most of our bauxite can't get together the way oil-producing countries got together on the price of oil. (Jamaica and Surinam, are original sources of two-thirds of the aluminum used in the United States.) The worry is not so much that we will end up without the basic raw material but rather that the price might be so high that we could not afford it. So much for the blackmail reason for recycling aluminum; the supply and demand picture in both the primary and recycling sectors of the aluminum economy is far more meaningful.

Jan 1, 1974

By Steve L. Bessinger, Luis B. Giraldo, Joram Shenhar, James D. Pile

This paper discusses the Helical Drag Bit (HDB) and its rock drilling applications with an emphasis on use in mining operations. The HDB is a drilling tool that employs cutting members arranged in a pattern to form a helical groove or thread within a borehole. This pattern of cutters can be used for several purposes including roof bolting in mining, interpretation of the lithology of the strata being drilled and low energy consumption drilling. Laboratory and field experiments have consistently shown increase of roof bolt-anchoring capacities in weak rock of more than 100% using the short encapsulation pull test method when boreholes are conditioned using the HDB. In 2004 a series of tests conducted in mines with weak roofs demonstrated the benefits of HDB technology for roof bolting applications in mining. HDB technology offers opportunities for new and beneficial approaches to interpret the geology of roof strata. During conventional drilling, traditional approaches to determine rock properties require simultaneous measurement of several parameters such as thrust, rotational velocity, torque and penetration rate. The unique geometry of the HDB possesses a characteristic that allows determination of the mechanical properties of the rock being drilled by measuring torque as a single drilling parameter. This capability greatly simplifies the process of determining rock properties and provides reliable results. Additionally, HDB technology has been demonstrated to offer significant advantages for rock drilling. A substantial portion of the rock is removed by the fracturing of the internal thread created in the rock bore by the tool taking advantage of the weakness of the rock in tension. Because the rock chips obtained in this process are relatively large, savings in energy are realized when compared to traditional drilling technologies.

Jan 1, 2005

By L. Alan Weakly

The Powder River Basin of northeastern Wyoming and southcentral Montana contains the largest strip minable reserve of compliance coal (0.27 kg or 0.6 or less Ibs of sulfur per million Btu) in the United States. In mining parlance, it is the mother lode. Wyoming's portion of the Basin is called the Southern Powder River Basin (SPRB). It has been the nation's top coal producer for the past nine years. And based on 1997 production statistics and estimated strippable compliance coal reserves, Wyoming should remain the nation's top producer for the next 51 plus years. In August 1994, ME featured 10 articles that covered all aspects of coal production in the SPRB. In this issue, five authors update the 1994 articles and provide a pre- diction of what the Basin will look like at the turn of the century. In addition to this article, the titles and authors of the other five articles include: ? "Geology of Wyoming's Powder River Basin coal field," by Gary B. Glass and Robert M. Lyman. ? "Coal quality challenges in the Powder River Basin," by Sharon Roness, Richard A. Turpin and Robert A. Young. ? "Markets for Southern Powder River Basin coal," by , Patti J. Best and Patrick W. Wright. ? "Evolution of mining equipment in the Powder River Basin," by Kenneth R. Miller and James L. Long. ? "Hauling coal into the 21st century," by Dave Willis and Will Cunningham.

Jan 1, 1998

By J. A. Herbst

Introduction The ability to evaluate the improvement resulting from the implementation of an automatic control system is essential to the Justification of its cost. This evaluation may occur after anew control system has been commissioned. In other cases an existing plant which is operated manually may be automated only In part in order to determine In ether the met of it should be. Finally. in some instances dynamic isolation my be used prior to installation of the control system to determine the strategy to be used or to evaluate the improvements In process performance expected from automatic control. This paper describes the development of a methodology for making these evaluations. In order to obtain an accurate assessment of Improvements In a short time, statistical methods can be employed. Mineral processing plant, are subjected to many types of both random and deterministic disturbances of various duration. The statistical method, available for process control at analysis are designed to counter the obscuring effects that random disturbances have on such as evaluation. The basis for evaluation and comparison is some freely chosen measures of process performance termed the performance index or objective function. The experimental data used to calculate the performance index should, if possible, be collected by alternately running a circuit Or plant with the two or more type, or control being tested ("serial testing”) or more preferably, by running two circuits with the two type, of control side by side ("parallel testing") . The performance index is a random variable so that when comparing two types of control, statistical hypothesis testing must be used. By testing s hypothesis statistically one accept, or reject, a (null) hypothesis [ ] concerning the mean or variance of one or more performance indices. For example, a hypothesis Ho might be that the mean of a performance index with stabilizing control is larger than with manual control. Defining a Performance Index The performance index, denoted by [ ] , is a measure by which alternative strategies or situations my be cam peered on either s technical or an economic basis (see Table 1). Technical measures are concerned with the effects of control on process variables or outputs or on the deviations of controlled variable, from their setpoints. For commotion circuit, important technical measures of performance are throughput, product fineness and the consumption of liners, media and electrical energy. For flotation circuits important technical .satires are recovery, grade and reagent consumption. Economic measure such a, cost and profit n usually determined from a combination of technical measures and are usually the final factor upon which a decision may be made, although a control system my achieve higher values of technical measure , the control effort expended my be of such magnitude that the economic measures, such as cost, are poor. Running Comparisons Comparison, between automatic and manual control are normally done with data obtained before and after control system Installation, unless ore characteristics remain the same during the period of data collection the results will be biased. By running the test circuit with the control system alternately turned on and curled off until all possible ore type, have been run through the circuit, unbiased result, can be obtained. This mode of testing is termed “serial testing.” An alternative and potentially more powerful and quicker made of testing is "parallel testing" in which two circuits, one with the type of control being tested and one without, arm run aide by side. In this type of testing both circuits process the same ore so that valid results occur sooner than with aerial testing. The data may be averaged before testing or the differences in the performance indices may first be calculated before averaging. However, the two circuits must be nearly identical in their mechanical characteristics otherwise differences other than the degree of control will bias the results. It mechanical differences exist than it my be necessary to adjust one or the circuits prior to testing. Sometimes it is possible to correct far mechanical differences based on Inherent efficiency calculations made with a model. Hypothesis Testing Once the data is collected, hypothesis fencing can be carried out to determine if the automatic control system has resulted in a statistically significant improvement. One can construct a histogram of the distribution or performance indices with am without control such as Figure 1, or the

Jan 1, 1991

By Im C. J.

The addition of coal preparation plants changed the coal industry during the past. Now it is time co once again improve the quality and types of coal products coming from future coal preparation plants to meet the changing needs of our society. Clean Coal Technology, along with federal support provided, is forcing our industry to provide cleaner coal products for industrial applications. Liquid fuels from coal is just one of many new products from a coal preparation plant that has a ready market in the transportation sector. UCC Research Corporation is developing these new liquid coal products and this paper will describe the progress and the new slate of coal products to be provided from future preparation plants.

Jan 1, 1989

A Mineração da Trindade (Samitri) is a major Brazilian iron ore producer. Founded in 1939, privately owned Samitri operates six mines with a total production capacity of 14.5 Mt/a (16 million stpy). The mines are located in southeastern Brazil in the state of Minas Gerais. They are operating in the iron ore quadrangle, Brazil's primary iron ore-producing region. In addition to iron ore production, Samitri has the capability to produce 350 kt/a (386,000 stpy) of ferruginous manganese ore from two mines, also located in the iron ore quadrangle. Historically, about 70% of Samitri's production of lump ore, sinter feed and pellet feed is exported. Destinations include Belgium, Luxembourg, France, Germany, Trinidad and Tobago, China, Turkey and the United States. Alegria Mine In September 1989, Samitri started a new processing plant to treat itabirite, a low-grade iron ore. The goal of the plant was to produce sinter feed (coarse fraction) and pellet feed (fine fraction). Primary separation of sinter feed from pellet feed was accomplished with conventional vibrating screens making a 0.4-mm (40-mesh) cut. The screen oversize was stockpiled as sinter feed. The undersize was deslimed with hydrocyclones and upgraded by conventional froth flotation. Resulting pellet feed grades ranged from 3% to 3.5% Si02. A change in pellet feed requirements by Samarco Mineração SA, a Samitri subsidiary, called for Si02 levels below 1 % and increased production levels. Moreover, market demands called for a change in sinter feed size distributions. Unfortunately, lower pellet feed Si02 levels could not be achieved with the existing process. This was because of the presence of 35% +0.15 mm (+100 mesh) in flotation feed. Flowsheet development. Laboratory and pilot-plant studies conducted at Samitri's research facility found that to achieve lower Si02 levels, the +0.15 mm (+100 mesh) in flotation feed must be kept below 5% to 10%.

Jan 1, 1997

By R. David Williams

Old mine workings are found throughout the Western United Sates on lands administered by the U.S. Bureau of Land Management (BLM), U.S. Forest Service (USFS) and private lands. Some of these mine workings date back to the late 1800s. There may be as many as 100,000 sites on lands administered by the U.S. Forest Service and Bureau of Land Management. The Bureau of Land Management has worked with the State of Montana and other agencies to identify and prioritize these sites on BLM administered lands. Following completion of the AML inventory work, the Bureau began an aggressive program to clean up priority sites. This presentation will highlight completed work as well as work in progress on several sites.

Jan 1, 2000

By C. A. Garcia

The solvent extraction of gold cyanide from alkaline cyanide solutions with monosubstituted guanidines, bis disubstituted guanidines and a tetrasubstituted guanidine was investigated. The guanidine functional group is protonated in alkaline solution and the guanidinium cation is stabilized so that the aurocyanide anion can be extracted even at -pH 12 if an appropriate carrier is used. Typical aprotic carriers including both aliphatic and aromatic solvents limit gold extraction by guanidines to pH 10; whereas the presence of an alcohol extends gold extraction to pH 12. UV spectroscopy suggests that the alcohol facilitates protonation of the guanidines, stabilizes the guanidinium cation, and facilitates gold extraction at high pH.

Jan 1, 1993

By C. Meyer, J. J. Eidel

Major gaps in understanding hydro- thermal systems remain after a century of studying fossil ore deposits and active geothermal areas. The periodically rejuvenated concept of "stacking" ore deposit types has never been verified by a continuous sample. Basal and marginal regions of both “fossil" and "active" hydrothermal systems normally lie beyond the limits of economic exploration, remaining inadequately exposed. Incomplete scientific under- standing of he vertical transitions clearly limits the efficacy of exploration programs for hydrothermal ores of all types. The Continental Scientific Drilling Committee's (CSDC) Panel on Mineral Resources has defined dedicated research objectives and add-on experiments to industry or government drill holes of opportunity.

Jan 1, 1988

By C. O. Brawner, A. Bellamy, D. S. Cavers

Pit slope designs at Nickel Plate Mine have used relatively steep interim and final wall slopes of 60 degrees overall. The rock is unusually strong and tough with most discontinuity sets being steeply dipping. An integrated program of monitoring and drainage has been used. Stopes of large extent which are generally unsupported occur on the property. For the most part, no deterioration of the stability of the stopes has occurred over the last 30 or more years. Mining methods through these areas have used a combination of fill s placed via VCR drop raises and crater blasting of the backs. One of the major challenges in mining through the stope areas is to maintain slope stability conditions and to reduce dilution of the higher value ore zones occurring immediately around the stope areas. The paper discusses geology, slope stability and mining methods at Nickel Plate Mine.

Jan 1, 1988

By Daniel H. Stevenson

Safety and health are fundamental values at Barrick Goldstrike. An effective safety and health program protects employees, controls costs and increases productivity. Barrick Goldstrike believes that all occupational injuries and illnesses can be prevented and that safety must be the responsibility of every employee on the property. Safety and health must be thoroughly integrated with the company's efforts to maximize production at the lowest reasonable cost. The goals of safety and production are not mutually exclusive. They must work together to achieve safe production. Barrick Goldstrike began to mine the Betze deposit in 1987. From 1987 to 1992, Barrick employed a traditional safety system using safety specialists on each crew. These specialists were responsible for ensuring that the work areas were safe and that employees were properly protected and trained in safe work procedures. As the work force increased, it became apparent that this system was not the most effective method of ensuring safe production. In 1992, Barrick Goldstrike implemented a loss control program. It was modeled after the International Loss Control Institutes's (ILCI) International Mine Safety Rating System. This program was based on the philosophy that safety is a management responsibility. It can be managed in the same manner that production and cost issues are managed. Under the loss control system, safety needs are identified and evaluated. Programs with performance standards are developed and implemented and the activities and results are regularly monitored. Between 1992 and 1996, Barrick Goldstrike worked at developing and improving its safety management systems. These efforts had a positive return. The incident rates began to decline as these improved systems were implemented. Studies were undertaken in early 1996 to evaluate the effectiveness of the safety and loss control programs in reducing accidents. The studies showed a strong correlation between the implementation of the loss control programs and the resulting reduction in all accidents. Studies in the process division revealed that Barrick had experienced reductions in personal injury accidents from the projected number that could have been expected had no changes been instituted. These reductions ranged from 39% in 1993 to 59% in 1995. These reductions from the projected rates held true for all types of accidents; personal injury, property damage and Mine Safety and Health Administration (MSHA) reportable.

Jan 1, 1997

By Richard R. Klimpel

INTRODUCTION Froth flotation is the most widely used and economic means of concentrating metal sulfide ores such as those containing copper, lead, zinc, nickel, molybdenum, and pyrite. Also recoverable are other metal species that are often associated with sulfide ores such as cobalt, platinum, gold, silver, etc. Froth flotation is a physico-chemical process for separating finely ground minerals from their associated gangue material. The process involves chemical treatment of a finely divided (ground) ore in a water pulp to create conditions favorable for the attachment of certain of the mineral particles to air bubbles. The air bubbles then carry the selected minerals, called valuable, to the surface of the pulp to form a stabilized froth which is removed and recovered. The unattached gangue material remains submerged in the pulp and is either discarded or reprocessed. To obtain the adherence of the desired mineral particles to the air bubbles, at least two specific steps must occur: a hydrophobic (water hating) surface film must be formed on the particles to be floated along with a hydrophillic (water wetting) film on all other particles; and a controlled bubble surface tension interface must be maintained, allowing for high particlelbubble collision frequency and efficient attachment or sticking of the particle to the bubble once collision has taken place. In most flotation applications, the above two steps are controlled by chemical flotation reagents. The collector is a chemical reagent which produces the hydrophobic film on the valuable mineral particle and is the primary driving force that initiates the flotation process. The frother is a chemical reagent which influences the collision frequency and attachment efficiency of hydrophobic particles and air bubbles. Thousands of research papers and books have been published on the chemical theory behind sulfide mineral collectors, e.g., Fuerstenau (1962), Fuerstenau (1976), Fuerstenau, et. al. (1985), King (1982), Leja (1982) and Moudgil and Somasundaran (1987), This article will only address and summarize some of the more practical aspects of collector usage. The industrial scale practice of froth flotation in sulfide mineral concentration has changed little since the 1950's. For example, of the approximately 80,000 metric tons of sulfide mineral collectors used commercially (1980) in the free world, almost 98% were known and manufactured in some form 25 years ago. A very interesting and informative history of collector development has been given by Crozier (1984). In addition, the industrial scale practice of froth flotation applied to sulfide ores has proceeded since the 1920's with often little direct (predictive) scientific explanation due to the extreme complexity of the flotation process. Empirical testing has been a mainstay of industrial flotation reagent development and use. Even today there is often strong disagreement between researchers as to the mechanisms of chemical flotation practices that have been performed successfully at an industrial scale for many years. As a result of the above environment which makes reagent cost/performance analysis difficult for new reagents, there is a strong tendency for the flotation operation to use, and reagent companies to supply, as cheap as possible raw materials and manufactured products that are quite general in application. In the last 20 years or so, there has been increasing technical effort to tailor make reagents for specific applications, but to date such work has had little commercial impact. It is clearly the hope of this author and others that this situation will change in future years as technology improves and pressure for improved flotation performance intensifies. This article is a condensation of collector usage trends quantified as part of a comprehensive industrially oriented applications program on froth flotation organized by Klimpel and coworkers (1979-1987) and as reported in various countries that participated in the program from 1978-1983. No attempt will be made to provide specific.

Jan 1, 1986

By J. Frenzel

The computation of hydrometallurgical equilibria is very difficult because of the many complex species in solution, the precipitates, condensed species, or solids, and the activity coefficient corrections necessary to non-ideal thermodynamics. Our objective was to tryout recently developed genetic algorithms to minimize free energy and solve the equilibrium computation. We selected test problems that were seemingly unsolvable with more traditional algorithms, and we applied genetic algorithms to them. We were pleased to find that genetic algorithms succeeded where other algorithms did not. We concluded that they are an effective tool for hydrometallurgical equilibria.

Jan 1, 1992

By F. W. Brackebusch

Paste is a high density mixture of water and fine solid particles with a relatively low water content (10-25%) such that the mixture has a consistency as measured by the ASTM slump cone test from slightly greater than zero up to nearly 12 inches (305mm). Particles of different size classes will not segregate or settle when the paste is not being agitated or when it is stationary in a pipeline. Cement may be a component of paste. Larger particles of aggregate can generally be added to a paste without greatly changing the pipeline transport characteristics. A paste may bleed water slightly when it is allowed to be motionless for periods of up to several hours, but the solids do not become so dense that the paste cannot be easily re-fluidized. The dividing line between the definition of a high density slurry and a paste is not sharp. It is a practical matter that must be considered when designing a pipeline transportation system. If the pipeline is very short, there is very little risk of plugging the pipeline with a high density slurry when flow is stopped for short time periods. With longer pipelines the mixture must remain stable without motion for periods as long as several hours to avoid pipeline plugging. The fine particles in a paste mixture can be composed of mine tailings or naturally-occurring clays, silts and fine sands. The mineralogy of the particles thus can have a wide variety from quartz and feldspar to clays, micas and even salts.

Jan 1, 1993

By Dan Xu, Song. Gaofeng, Zhen Wei, Zhihe Wang

"With decades of development and exploitation of coal resources, the first batch of coal-based cities in China are faced with the challenge of economic shrinkage and environment deterioration due to the rapid resource exhaustion and single industrial structure. Nowadays, as a policy instrument for sustainable development, a nationwide circular economy mode has been implemented during the design and planning of new coal mines to address the challenges arising from economic depression, energy shortage and environmental pollution. It should be mentioned that several national coal bases and most of constructing and planning coal mines are located in the underdeveloped areas in the Midwest of China which means that the distance between supply source for energy resources and the demand market is significantly increased. Moreover, the eco-environment vulnerability in these rural areas should be taken into serious consideration. Therefore, after comparison and analysis with several successful coals based and diversified circular industry chains, this paper presents a case study on the circular economy park (CEP) in the northwest of Shanxi Province. Through discussion and evaluation of ‘1+3’ mode in the CEP, this paper aims to enhance the understanding of coal mine sustainable development and shed light on the relationship between resources exploitation and local economic development.1. Introduction Earth's fossil energy resources are crucial to both economic prosperity and human well-being. Taking coal mining and consumption as an example, coal has been widely used to generate electricity since the 1880s, and more than 40% of the electricity globally is provided by coal nowadays. However, as one of the largest worldwide anthropogenic sources of carbon dioxide releases (39% of global CO2 emissions), the extensive excavation and utilization of coal have brought a series of side effects to both natural environment and human health (Wikipedia 2017). As the largest coal producer and consumer in the world, China is leading the list over the past decade (as shown in Figure 1) (BP 2016). The excavation and utilization of coal resources have made a crucial impact and irreplaceable contributions to China’s industrial development and economic prosperity (Long and Zhang 2009). However, most of the air pollution in China are also attributed to the simplified and extensive exploitation of coal resources, e.g., 90% of SO2, 67% of NO, 70% of smoke ashes, and 70% of CO2 in 2016. In recent years, most of North China and the developed coastal areas were wreathed by smog due largely to the oversimplified extensive utilization of coal, suggesting that the development patterns of coal utilization need to be reshaped so that both the biosphere and humanity could thrive equally."

Jan 1, 2017

By Lawrence A. Roe

This paper describes research and development efforts leading to a wet process for the beneficiation of Western talc ores in which the values are primarily present as soft, platy talc mineral. The mineralogy of the ore, as it relates to the logic of utilizing an uncomplicated, attrition-scrubbing sedimentation process is described. Bench-scale laboratory testwork and a pilot-plant test program are described. The pilot-plant program included production of several tons of products. The thickened talc slurries were very difficult to dewater prior to the drying step. Dewatering difficulties were overcome by use of a high-speed centrifuge. The centrifuge cake was dried either by tray, flash or spray drying. The successful use of one high-grade talc product as titanium dioxide extender in paper is discussed. The talc product has extremely low abrasion values, an important characteristic for minerals used in paper manufacture. It is concluded that this wet process for soft talc ores is capable of producing high-purity talc products for paint, paper, cosmetics and other industrial uses re-quiring very pure soft talc.

Jan 1, 1972