Search Documents

By Ted D. Johnson

INTRODUCTION The tailing dam is part of the SOHIO L-Bar Uranium Mine and Mill located about 70.8 kilometers (44 miles) west of Albuquerque in northwestern New Mexico. The dam location is shown on Figure 1. The tailing dam is one of the last upstream method dams permitted in the industry. Design and construction aspects of the project, as well as operation and maintenance considerations, are reviewed herein. Since initial construction, SOHIO Western Mining Company and Woodward-Clyde Consultants have developed several modifications and improvements in the dam's operating and monitoring procedures. This work has been done in coordination with the New Mexico State Engineer's Office and in accordance with recommendations in a report done for the Corps of Engineer's Phase I Dam Inspection Report. Modifications and improvements described should be of particular interest to owners and operators of other tailing dams utilizing the upstream method of deposition. The tailing facility was designed for a 10-year life to provide an ultimate storage capacity of 6 1/2 billion kilograms (7 1/2 million short tons) in an area of about 180 acres. A plan view of the tailing dam is shown on Figure 2. The tailing consists of approximately 75% sand size material and 25% fines (material passing the No. 200 sieve). The tailing dam includes a small earth starter dam with raises of the dam accomplished using tailing deposited by upstream method techniques. The starter dam is a homogeneous embankment about 610 meters (2000 feet) long, a maximum height of 12 meters (40 feet) and 2 1/2:1 (horizontal to vertical) upstream and downstream slopes. The starter dam contains an internal drainage system which includes a near vertical chimney drain connected to horizontal finger drains. A typical section through the maximum height of the starter dam is shown on Figure 3. A small confining dam, approximately 1.6 meters (5 feet) high, is constructed beyond the limits

Jan 1, 1980

By Chas. F. Jackson

INTRODUCTION This paper is one of a series dealing with mining methods and costs, prepared and published under the sponsorship of the US Bureau of Mines (USBM) and made possible through the cooperation of many mining companies in the US and foreign countries. The data presented have been obtained from papers previously published by the Bureau dealing with indi¬vidual mines, from the technical press, and from infor¬mation furnished by the mining companies. DEFINITIONS Top Slicing The term top slicing is commonly applied to that method of mining in which the ore is extracted by a series of timbered slices, beginning at the capping; the slice is caved, bringing down the capping to the floor of the slice; the succeeding lower slices are mined up to the overlying mat or gob, consisting of an accumulation of timber from the upper slices and broken capping, which follows the mining progressively downward (Fig. 1). The term has also come to be applied to the mining of ore bodies only one slice thick, by a series of tim¬bered slices one beside the other. The timbers are blasted out, bringing the capping down to the floor, suc¬ceeding slices being driven alongside those already caved (Fig. 2). In USBM classifications of mining methods, top slic¬ing has been placed under the heading caved stopes. The method differs fundamentally, however, from the cav¬ing methods of mining in which the breaking of the ore itself is accomplished by caving action induced by undercutting. In top slicing the ore is broken by the ordinary methods of drilling and blasting, and only the capping is broken up by caving. Main Levels or Haulage Levels Main or haulage levels are the main extraction levels on which the ore is hauled to the shaft. These levels and the shaft constitute the preliminary development of the mine.

Jan 1, 1982

By Jed H. Mosgrove

One of the most interesting of all the subjects required of persons studying the different facets of coal mining is coal mine gases. Some mine gases have been a real problem since the very beginning of underground mining, and in the early days there was insufficient knowledge to cope with them. The history of mining shows that until about the last 50 years, much work was done primarily by the hand methods which are primitive by today's standards. Miners had to contend with gases without the aid of enclosed lighting, permissible mine machinery, sophisticated testing devices, and high-pressure ventilating fans. In early days the miners were not educated about the different mine gases nor did they have the technical equipment to determine the actual composition of the deadly atmospheres they encountered. They simply applied a descriptive term to each gas or mixture of gases depending on its effect on a person or the surrounding atmosphere. The gases or mixtures of gases were then referred to as "damps," a term which was probably derived from the German word "dampf," meaning vapors or gases. The more common damps encountered were : Blackdamp A condition of the atmosphere in which a miner's light would be extinguished and in which breathing would be difficult, sometimes even resulting in suffocation. An atmosphere deficient in oxygen which could contain a combination of any of the mine gases Firedamp A flammable mixture of methane and air which would either burn or explode when ignited. White Damp A mixture of gases containing carbon monoxide, most often found in mines during fires or after explosions.

Jan 1, 1981

By Ruckmick J. C.

Elemental sulphur occurrences are widely distributed in two geological environments: -1-Basins containing hydrocarbons and zones of Cenozoic vulcanism. However, very few of these constitute deposits large enough to be of commercial importance. Almost all of the elemental sulphur mined in the world comes from bioepigenetic deposits in petroliferous basins. These deposits occur in two general structural styles: diapiric (salt domes) and stratiform. Examples of diapiric deposits occur in the Gulf Coast basins of Texas, Louisiana, and southern Mexico. Examples of stratiform deposits occur in the Fergana and Amudarya depressions of Central Asia, the Mesopotamian Depression in Iraq, the Cis-Carpathian Trough in Poland and Russia, and the Permian Basin in Texas. Economic bioepigenetic sulphur deposits range in size from approximately 1 million tons of sulphur in the smaller salt dome deposits to more than ZOO million tons of sulphur at the Mishraq stratiform deposit in Iraq. Total world production from bioepigenetic deposits amounts to approximately 16 million tons of sulphur per year, one-half of the world's present annual consumption of elemental sulphur. Most of the balance of the annual consumption is recovered from sour gas and petroleum. All bioepigenetic sulphur deposits share remarkably similar origins and characteristics. They are formed by anaerobic bacterial replacement of gypsum or anhydrite in tilted basins where evaporite beds are underlain by petroleum. Figure 1 illustrates a generalized cross-section of a salt dome sulphur deposit. Figures Z, 3, and 4 are cross-sections of three types of stratiform sulphur deposits. In terms of sulphur genesis, the only significant difference between the salt dome and stratiform deposits is that the positioning of the anhydrites above the petroleum in the salt domes is caused by diapiric rather than sedimentary processes. In the salt domes, the residual anhydrites of the cap-rocks are accumulated by solution and removal of halite by artesian ground waters.

Jan 1, 1978

By Gealy W. Wallwork

The administrative processes of coal mines are becoming increasingly complex. As society evolves into a more complicated structure with greater emphasis on individuality, government regulations reach deeply into every activity in an effort to force individuals into a standardized mold. These contradictory pressures add an extra burden to the administration of a mining operation. Recent years have brought a substantial change in the skills needed by mine supervisors and managers. As a result, a better understanding of the administrative functions is necessary. The mine superintendent has the overall responsibility for the mine; for effective operation he must be sufficiently knowledgeable to oversee all the complex functions that make up the mine. This chapter does not cover all the administrative requirements because of the variation in mine operation and in company policies and organizational structure. It does attempt to identify the administrative functions that would be required at a large mine with a preparation plant. It is assumed that the mine operation is decentralized with very little duplication of functions at the organizational levels above the mine. Thus each function is assumed to be relatively complete at the mine and under the general supervision of the mine superintendent.

Jan 1, 1981

By Louis J. Jansen, D. E. Ranta

Techniques utilized to incorporate geological data in computer modeling and ore reserve estimation have undergone considerable evolution during the past fifteen years. Computer analysis and evaluation of two precious metal deposits are presented as examples of innovative computer techniques developed at Asarco. The first is a gold deposit occurring in a steeply dipping Precambrian greens tone sequence. The second is a manto-like manganiferous silver deposit occurring in a relatively flat sequence of Late-Paleozoic sediments. In both deposits, four sub-horizontal zones of geological influence are evaluated.

Jan 1, 1992

By Carol A. Hill

Native sulfur occurs with barite, celestite, and bioepigenetic calcite in the Culberson, Pokorny , and Leonard Minerals deposits, Delaware basin. The sulfur in these deposits, in "castile" masses, and in deposits of the Fort S tockton district have 6 34s values between +9 and -15. Native sulfur in the caves of the Guadalupe Mountains is somewhat lighter [(634s = -15 to -25)]. Barite in the Culberson, Leonard Minerals, and Comanche Creek sulfur deposits have 63% values of +35 to +73; celestite in the Culberson and Leonard Minerals occurrences have values of +38 and +36, respectively, and 87Sr/86Sr values of 0.707808 and 0.708138, respectively. Barite associated with sulfide, deposits, Guadalupe Mountains, have [634s] values of +41 to +62. Barite at Seven aeart Gap, Apache Mountains, is somewhat less enriched in heavy sulfur [(634s = +14 to +37)].

Jan 1, 1992

By R. K. Zipf

Recent scientific studies by researchers at the National Institute for Occupational Safety and Health (NIOSH) and the U.S. Army Corps of Engineers (USACE) presented the worst-case explosion pressures that can develop if a methane-air mixture of a certain composition and dimension accumulates and ignites within a sealed area of a mine. The Mine Safety and Health Administration (MSHA) issued its final rule on sealing of abandoned areas which considers potential explosion pressures and the risk of achieving the necessary conditions. The new MSHA seals regulation has increased the pressure design criteria an order of magnitude beyond the old standard of 140 kPa (20 psi) to 800 kPa (120 psi). However, there still are major knowledge gaps pertaining to seals and sealed areas including: (1) the composition of the sealed area atmosphere and how it changes in time and space, (2) explosion pressures that might actually develop within sealed areas, (3) engineering procedures to follow when designing seals and seal installations, and (4) guidelines to manage the atmosphere within sealed areas with monitoring or inertization. NIOSH has initiated a seals research program with collaborators from Safety in Mines Testing and Research Station (SIMTARS) in Australia, West Virginia University (WVU), the Naval Research Laboratory (NRL), and USACE. Highlights of progress so far include: (1) construction of a gas explosion tube at Lake Lynn Laboratory for studying large methane-air explosions, (2) computer simulation of the fluid dynamics of high pressure methane-air explosions, (3) development of seal analysis methods considering construction materials, reinforcement and the seal foundation, and (4) development and testing of innovative seal designs that utilize inexpensive, readily-available rock rubble to resist high explosion pressures. NIOSH researchers aim to provide sound engineering guidelines to better address the new MSHA seal regulations. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By M. R. Nelson

Continuing experience in the Black Hills, South Dakota, indicates the persistence of several natural contaminants in mine waste effluents under circumneutral pH conditions. Selenium and arsenic are the most problematic environmental contaminants observed in these effluents. The contaminants are present in ore and waste rock as naturally occurring trace elements, and under the physico chemical conditions of the mine waste repositories are mobilized by oxidation and desorption reactions into infiltrating water. Characteristics of the mine wastes, waste repository construction, and Black Hills climatic conditions, indicate these natural contaminants may persist well into the future causing long-term mine closure liabilities, a difficult challenge to both mine operators and regulators.

Jan 1, 2003

By Peter T. Luckie, Felicia F. Peng

INTRODUCTION The maximum recovery of cleaned coal at the required quality is of major concern to plant operators. However, the quantity and quality of products of coal cleaning, predicted by theoretical calculation based on washability studies and determined in the operation of actual commercial cleaning plants, will be different for each coal. Therefore, during the last half century, coal preparation engineers have repeatedly sought methods for evaluating the technical and economical efficiency of separating coal in coal cleaning equipment and for predicting the quantity and quality of cleaned coal produced, as well as profit- ability for the entire plant. Many formulas have been proposed by investigators to evaluate the efficiency of various coal cleaning operations. Performance criteria in use today are capable of defining all of the important aspects of a given concentrating operation; however, each criterion has certain restrictions or limitations. It is important, therefore, to understand how such formulas can be used and the problems involved in their construction. Technical Measures of Equipment/Plant Performance Conventional measures for evaluating the performance of a preparation plant are generally the same as those used to evaluate equipment performance. Measures involving separation efficiencies are influenced by the following three broadly encompassing primary factors: (1) density composition of the feed coal, (2) design characteristics of the cleaning unit, and (3) relative density of the separation. Since separation efficiencies are dependent on factors involving the nature of the coal, they are termed dependent criteria and represent a very broad technical indicator of an individual process or plant performance. Performance measures known as independent criteria are influenced mainly by quantitative errors inherent in the design and operation of the processing equipment. Economic Measures of Plant Performance True assessment of coal cleaning methods require reference to economic measures such as profitability. During the years in which technical efficiency criteria for characterizing plant performance were being improved, coal preparation engineers were also seeking appropriate economic criteria to assess plant performance. Technical and economic effectiveness of plant performance are important parameters for coal preparation flowsheet design. The relationship of the technical and economic parameters can be formulated in an economic model and mathematical model with the aid of computers. The computerized models

Jan 1, 1991

By Bernard F. Anderson

INTRODUCTION In this chapter, the term "down-the-hole drill" (DTH drill) is used as a generic name that encompasses the various trade names and other references such as "downhole drill," "in-the-hole drill," etc. This chapter is limited to a description of DTH drills used in stoping large underground ore bodies. DTH drills differ from conventional drills by virtue of the placement of the drill in the drill string. The DTH drill follows immediately behind the bit into the hole, rather than remaining on the feed as with ordinary drifters. Thus, no energy is dissipated through the steel or couplings, and the penetration rate is nearly constant, regardless of the depth of the hole. Since the drill must operate on compressed air and tolerates only small amounts of water, cuttings are flushed either by air with water-mist injection or by standard mine air with a dust collector at the collar. HISTORICAL DEVELOPMENT Mine managers have long known the economies enjoyed by quarry and open-pit operators in producing large quantities of ore. The savings are due primarily to the availability of massive equipment, capable of drilling large blastholes to reduce the amount of drilling, increase the fragmentation, reduce secondary blasting, and im¬prove the flow of the product. In an attempt to reduce underground mining costs, various methods are used for long-hole drilling, includ¬ing standard pneumatic percussion drifters and diamond drills. These systems have their shortcomings; percus¬sion drills are limited to small hole sizes and they ex¬perience excessive deviation and significant loss of energy with increased depth. The diamond drills provide deeper and straighter holes, but only at high cost. Both systems suffer from high noise levels, low penetration rates, and poor explosives distribution, among other problems. When the mining companies approached the drill manufacturers for a compact and portable large-hole jumbo for underground use, they specified not more than 1 % deviation on 60 m (200 ft) of vertical hole and a penetration rate of 15 m/h (50 fph). On Dec. 23, 1960, a test unit was placed in service in Montana and met the performance criteria. Though lacking the so¬phisticated features available today, the economies of surface blasting were brought underground. Unfortunately, the first system did not gain immedi¬ate acceptance in the industry. Among the factors con¬tributing to its demise were resistance to change, the need to alter development methods for the ore bodies, and a lack of flexibility in moving the rig from setup to setup and from level to level. In 1972, the mining industry again challenged the drill manufacturers to provide a workable jumbo that would combine compactness, ease of maintenance, relia¬bility, and efficiency, all on a self-propelled chassis. The manufacturers responded by providing improved jumbos, which have been accepted with enthusiasm throughout the mining industry. Today's DTH jumbos are capable of drilling from 100 to 200 mm (4 to 8 in.) diam holes that can be reamed to even larger diameters. The holes can be drilled to depths of 150 m (500 ft), depending upon ground conditions and the capability of the jumbo to retrieve the steel and drill. Fig. 1 illustrates a typical DTH jumbo. APPLICATIONS The uses to which DTH drill jumbos have been put are quite numerous, with new uses being found regularly. For convenience, these uses may be classified as primary blastholes and nonblasting holes. Primary Blastholes The original purpose for the development of the DTH jumbo was for drilling primary blastholes that could be mined by open-stope methods. Prior to the advent of the DTH jumbo, extensive development was required before production drilling could begin. Sub¬levels were required to allow access for column-and-arm stopers or ring/fan jumbos, to the extent necessary based on the effective penetration of the chosen machine. With the DTH jumbo, the mine engineer is able to reduce preproduction time and development costs. How¬ever, the most significant saving results from an im¬proved cost per ton of broken ore in the production phase. To utilize a DTH system, only a top heading and drawpoints are necessary. The top heading can be the width of the ore body with a 3.7-m (12-ft) back. A drop-raise pattern is drilled and shot to begin the stoping operation, providing a free face for subsequent blasting. A typical layout is illustrated in Fig. 2. The advantages of this system include: 1) Drilling and blasting are independent operations, and blasting can be performed at a rate congruous with the mine's ton-per-day capacity. 2) The development layout is simplified. 3) Good explosive distribution is achieved, provid¬ing more uniform fragmentation. 4) Environmental conditions for operators are im¬proved, including improved safety with all work directed downward (not overhead), lower noise levels, little fog, and a reduced dust count. 5) Improved production per manshift. 6) Simplified and easier operator work cycles. 7) Reduced cost per ton of product. 8) Fewer holes lost due to ground shifts. Nonblasting Holes With the introduction of the compact DTH jumbos, other practical uses became apparent, including the drilling of: 1) Holes for sand fill, from level to level and from level to stope. 2) Drain and dewatering holes. 3) Power and communications cable holes.

Jan 1, 1982

By Ian P. G. Hutchison

12.1 INTRODUCTION This chapter deals with the tools required to design leach operations to minimize spillage from leach pads and ponds and erosion damage during flood events or prolonged wet periods. It outlines methods used to design for prolonged dry periods when water shortage can be a problem. Seasonal operational aspects such as winter shutdown and coping with spring snowmelt periods are also discussed. General criteria useful when designing pregnant and barren solution ponds are also outlined. The aim of these notes is to provide designers and operators with a simp1ified approach to developing design parameters which make effective surface water management easy to achieve without resorting to extensive or elaborate analyses. Section 12.2 briefly outlines the types of problems associated with wet climates and floods, as well as dry periods. Determination of flood design parameters is discussed in Section 12.3. Circuit water balance and pond sizing are outlined in Section 12.4. Pond design considerations are included in Section 12.5. Worked examples are included in Section 12.6. 12.2 RAINFALL/RUNOFF PROCESSES There are two types of rainfall-runoff processes that are important when designing heap leach facilities. The first of- these is the short-term, intense rainfall or snowmelt events that occur over a period of a few minutes or hours, causing flooding that can lead to erosion damage and overtopping of ponds and containment dikes. Specific problems that can manifest themselves during these events include: • Washout of access roads; • Damage to containment dikes; • Flood water contamination of circuit water; • Damage to process water ponds by perimeter erosion or overtopping and erosion; • Loss of process circuit fluid due to breaks in containment dikes or process water ponds; and • Erosion of leach pile and consequent sediment contamination of process fluid. Other types of rainfall -runoff processes that could cause problems are the long-term-(generally months-long) wet or dry periods. Extended wet periods

Jan 1, 1988

By Babcock. C. O.

This report presents equations derived from experimental testing to convert borehole pressure cell data from vertical and horizontal cells to the biaxial ground stress changes. While hydraulic pressure cells in boreholes have been in extensive use since 1957, methods of data reduction have been slow to develop. The methods of Sellers (1970) and Bauer et al. (1985), respectively, indicate a linear relationship between cell pressure change and the rock stress change. Lu presented a theory for creep behavior (Babcock et al., 1982). In the present work, in laboratory testing, the logarithm of the cell pressure was related to the stress change in seven elastic materials for a range of Young's moduli of 3.45 to 85.5 GPa (0.5 to 12.4 x 106 psi). The gage response depends upon the setting pressure of the gage, the gage pressure at any time, the rock properties, and the cross-sensitivity of the gage to transverse loading. The setting pressure of the cell should be proportional to the Young's modulus of the rock, the absolute stress can be determined by overcoring in strong rock, and the in situ Poisson's ratio can be estimated in some cases from the cell responses.

Jan 1, 1986

By Frederick K. A1lgaier

The Bureau of Mines' Denver Research Center initiated a subsidence research program in 1978. The short ten goals of the program were to determine practical methods and equipment for measuring subsidence and demonstrate these methods by monitoring subsidence at several mines having mining, geologic and topographic variables typical of those encountered in the western United States. Data from the monitoring program would be supplied to cooperating mining companies and used by the Bureau to accomplish the long term objective of developing and validating subsidence prediction techniques applicable to mines in the West. Subsidence monitoring is being conducted at five mines in Colorado and Utah with substantially different mine plans, mining methods, depths of cover, and topography. The monitoring procedures used at each site are similar and include designing the monitoring network layout, installing the subsidence monuments, initial and periodic surveying of the monuments, and processing the survey data. The network layout, surveying methods, and types of monuments vary according to the conditions at the individual sites and the type of data being collected.

Jan 1, 1982

By Gennaro Gerald Marino

In this paper the main subsidence- ground-structure interactions and an overview of the response of surface structures to subsidence ground movements are presented. The purpose of the paper is to augment our understanding for more effective application of available data as well as to highlight the essential site conditions in building response. The data presented general1 y applies to houses to structures up to 2-3 stories high and no more than several hundred feet in length. Superstructures of these buildings are supported by exterior (wood-frame or masonry) bearing walls with the interior floor loads carried by essentially one row of interior columns. This paper is not directed towards the response of tall buildings, steel-framed structures, or building types commonly associated with schools, churches, libraries, etc.

Jan 1, 1986

By J. J. Peshel

As per the current conceptual design presented by the Department of Energy, the exploratory shaft facility (ESF) becomes a part of the repository if the Yucca Mountain site is found suitable for repository development. Therefore, the design of the ESF should be compatible with the performance requirements for the repository. The construction methods selected should limit to the extent practical, the degree and the extent of damage to the surrounding rock mass. The ESF construction and operation should be compatible with the site data gathering activities, such as geological, thermomechanical, hydrological and geochemical testing.

Jan 1, 1991

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

4.1 INTRODUCTION There have been numerous methods developed for predicting the final subsidence and final displacement profiles (Voight and Pariseau, 1970; Brauner, 1973a; Kratzsch, 1983). But for discus- sion purposes, they can be classified into six categories: theoretical, profile function, influence function, graphical, physical, and numerical modeling. The theoretical method employs mainly continuum mechanics theories and attempts to explain the mechanisms that lead to sur- face subsidence. Many models using nearly all kinds of material behavior have been developed. These include elastic (Salmon, 1963; Berry, 1964), plastic (Pariseau, 1968), viscoelastic (Iman, 1965), and elastoplastic (Dahl, 1969). The Profile Function Method is essentially a method of curve-fitting against the measured subsidence profiles in a particular mine or region. There are more than 20 profile functions developed empirically for nearly all major coalfields in the world. These include, to name just a few representative ones: Hungary (Martos, 1958), Japan (Hiramatsu and Oka, 1968), Russia (Avershin, 1947), United Kingdom (Wardell, 1965), and USA (Peng and Chen, 1981; Karmis et al., 1984). The NCB's graphical method in the subsidence Engineers' Handbook (1975) also belongs to the profile function method. The influence function method was first proposed by Bals (1931/1932). It was further developed in various periods and stages by Knothe (1957), Liu and Liao (1965), Brauner (1973a) and Marr (1975). This method is now widely used in various parts of the world. The physical models include sand (Litwiniszyn, 1959; Pariseau and Dahl, 1968) and gelatin (King and Whetton, 1958; Khair et al., 1986). They are used mainly to study the parameters that control subsidence behavior. The most popular numerical method is the finite element technique. It can simulate nearly every conceivable material behavior, inhomogeneity, bedding planes, anisotropy, and various boundary conditions. This versatility is absolutely necessary considering the ever-changing geologic and mining conditions encountered. In the following sections, only those methods that have been applied to US coalfields will be discussed. Furthermore, the methods for prediction of several key parameters such as maximum subsidence, maximum possible subsidence, and maximum displacement are discussed first, because they are the key parameters to be used in the profile function, influence function, and graphical methods.

Jan 1, 1992

By Harry R. Asche, Manfred K. Lechner

The Cross City Tunnel comprises 2km of a new underground traffic route in Sydney, Australia. The route is very complex, involving some six separate tunnels and three underground Y-junctions. For almost 200m the six tunnels run parallel at different level sunder William Street, Sydney. Almost all of the route runs adjacent to the City Business District of Sydney and adjacent to or below many major buildings and services. The planning and design of this project is described. The geometric arrangement is achieved with a strong dependence on 3D road design packages. Road alignment constraints include land acquisition and proximity to existing tunnels and basements as well as maintaining separation from the other tunnels in the scheme. Geotechnical and hydrogeological studies are described. Findings discussed include the high horizontal stress field in the Sydney area and investigation of incised palaeochannels on the route. Methods of design for the tunnels and Y-junctions are described, as well as methods of settlement prediction for the buildings and services. The latter includes the settlement assessment for more than 200 buildings, many in excess of 20 storeys, as well as services including all of the city railway lines in Sydney.

Jan 1, 2003

By Marco D. Boscardin

During subsidence, the ground surface may settle, change slope, change curvature, go into tension, and/or go into compression. In response to these ground movements, buildings and buried utilities in the subsidence area may settle, tilt, bend, distort, and sustain extension, compression and/or torsion. In order to develop measures to protect existing structures and utilities, or to design new structures and utilities to withstand potential movements in areas of subsidence, it is necessary to understand the interaction between the ground and the building or buried the utility. This paper reviews subsidence-induced ground movements, how these ground movements are transmitted to and accommodated by buildings and buried pipelines, and how these structures may alter ground movements relative to free field subsidence-induced ground movements.

Jan 1, 1986

By K. J. Sollman

As a class, silicate minerals have likely found the broadest, if not largest volume, use in combination with polymeric binders of all industrial minerals. Among the silicates, calcium metasilicate, wollastonite, enjoys a front runner position in a near universal sense. It is a viable and desirable part of composites ranging from thin films to large moldings; from a common filler/extender for paint for your garage to a reinforcement for the exterior surfaces of a luxury vehicle affordable to very few. This article is focused upon the variations in particle morphology and the surface characteristics which, by way of commercial examples and discussion of active research programs, make this environmentally benign mineral so unique.

Jan 1, 1993