Search Documents

By T. Scheldt, M. Lu, A. Myrvang

Abstract: In this paper both continuous and discontinuous modelling are utilised in order to analyze the stability of the Gjøvik Olympic Mountain Hall. The large span cavern (62 m) was built for the 1994 Winter Olympic Games at Lillehammer, and is a unique case study because of the large amount of available input data, through a comprehensive pre-investigation, stress and deformation monitoring program before, during and after the excavation. Phase2, a two-dimensional non-linear finite element program, and the Discontinuous Deformation Analysis (DDA) are used as representative tools for continuous and discontinuous modelling, respectively. The analysis results are compared and discussed taking the reliability of the models, time-consumption and costs into consideration. Some guidelines for the total modelling process, from field measurements to final results, are also presented. Zusammenfassung: In diesem Artikel werden sowohl kontinuierlich als auch diskontinuierlich Modellierung verwendet, um die Stabilität, der in den Berg gebauten Olympiahalle in Gjøvik zu analysieren. Die Olympiahalle wurde 1994 zu den Olympische Spielen in Lillehammer errichtet. Ihr Dach erstreckt sich über eine Breite von zweiundsechzig Meter. Für den Bau wurden umfangreiche Daten durch Voruntersuchungen, und Überwachung von Gebirgsspannungen und Deformationen bevor, während und nach Exkavation eingesammelt. Auf Grund dieser großen Datenmenge stellt die Olympiahalle ein herausragendes Beispiel für den Bau ähnlicher Projekte dar. Für die kontinuierlichen Modellierungen wurde „Phase2“, ein zwei-dimensionales, nicht lineares „endlich Element“ Rechnerprogramm angewandt. Die diskontinuierlichen Modellierungen erstellte man mit Hilfe von der „Diskontinuierliche Deformations Analyse“ (DDA). Die Analysenergebnisse sind mit Rücksicht auf die Zuverlässigkeit der Modelle, Zeitverbrauch und Kosten verglichen und diskutiert worden. Im Artikel werden Richtlinien für den Modellierungsprozess von Dateneinsammlung bis Schlussfolgerung gegeben. Résumé: Dans cet article la modélisation continue et discontinue sont utilisés pour analyser la stabilité de Gjøvik Olympic Mountain Hall. Cette caverne de grande portée (62 m) a été construite pour les Jeux Olympiques d’Hiver de 1994 à Lillehammer, et est une étude de cas unique grâce à la grande quantité de données disponibles, de par un programme de pré-investigation compréhensive, monitorage des contraintes et déformations avant, pendant et après l'excavation. Phase2, un code d’éléments finis non linéaire à deux dimensions, et l’Analyse en Déformations Discontinues (DDA) sont utilisés comme outils représentatifs de la modélisation continue et discontinue, respectivement. Les résultats d'analyses sont comparés et sont discutés, prenant en compte la fiabilité des modèles, la consommation en temps de calcul et les coûts. Quelques indications pour le procédé total de modélisation, des mesures sur place aux résultats finaux, sont aussi présentées.

Jan 1, 2003

By N. D. Fernandes

Labour-intensive narrow reef stoping, as traditionally practised in South African gold and platinum mines, is almost unique in the modern first-world mechanized mining environment. Shortcomings of the system include the ever increasing cost of labour, a cap on achievable productivity and a poor safety record, particularly in the field of rock-related accidents. In the absence of sustainable alternative technologies, the South African mining industry has spent millions of rands improving the present system, focusing on improving workplace safety. This paper details the changes to stope support at Impala Platinum?s Rustenburg operations, and the impact on rock-related safety performance. Keywords Stope panel support, narrow reef stoping, improving workplace safety.

Jan 1, 2011

By P H. Ferreira

The mechanisation of mine development is becoming increasingly important in our South African and Southern African mines with increased emphasis on safe and efficient mining. Raise, blind and shaft boring offer mechanised solutions for excavations such as:- [reef raises stope boxholes and shaft ore passes ventilation passes and shafts chairlifts large vertical hoisting shafts (in excess of 1200 metres in depth) angled hoisting shafts (from small to large diameter bored holes)] These techniques will be discussed with reference to relevant applications and the author?s comparison between conventional drill and blast techniques.

Jan 1, 2005

By D. F. Malan

Considerable practical knowledge and effective use of empirical evidence is required in the design of tunnel support systems. In many instances, it is unclear how individual support elements interact with fractured rock and which elements of the support system are critical in controlling and containing the movement of material proximate to the excavation. The present paper outlines a displacement discontinuity approach that allows the coupling of surface constraints, in the form of liner or mesh material, to an explicit representation of time-dependent rock discontinuity creep movements. The method is illustrated for a simple square-shaped tunnel profile in which the fracture zone is mobilized by an imposed stress field. A crucial aspect of the model is the computational treatment of the coupling between the liner material and there presentation of the fractured rock mass. This allows the response of the liner material to be assessed quantitatively in terms of the possible reduction of movement in the rock mass. The importance of installing the liner timeously after the excavation is formed is illustrated in a specific example. A number of computational difficulties in simulating liner-rock interaction mechanisms are identified.

Jan 1, 2008

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental Sampling Error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centered on the sampling constant K and the exponent, alpha (a), of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis (DSA) method and the heterogeneity test (HT) method purport to provide such a constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine and Lily mine. Two of these mines (Mponengand Kloof) are typical Witwatersrand-type gold mines, while the third is an Archaean-type, shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appears to be too small and does not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis, are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2009

By R. Thomas

A Honeywell TDC 2000 central process control system was installed at Rössing in 1984. The system controls the metallurgical operations from crushing to the finished product of uranium oxide and manufacture of sulphuric acid. The operation was previously controlled from nine separate local control rooms. The paper briefly reviews the design and commissioning of the control system on an operating plant and discusses the impact on manpower organisation and training needs. Development of the process control system during its first two years of operation is reviewed and a summary is given of the current status of computer control at Rössing. The impact of the new system on overall plant operation and performance efficiency is also briefly described. In conclusion, future developments of computer control and overall optimisation of metallurgical operations are reviewed.

Jan 1, 1987

By Z. Ruetz

Portable X-ray fluorescence (pXRF) analysis has been widely adopted in the geochemical and environmental field as a cost-saving alternative to standard analyses. This paper outlines the efficacy of a method for indirectly quantifying organic copper content in solvent extraction circuits via stripping of the chelated metal with concentrated sulfuric acid in a single contact and subsequent pXRF aqueous analysis. pXRF analysis is common within the mining industry but presents unique challenges with liquid analysis, the most prevalent of which are briefly discussed. This method was developed specifically for mining operations with regional constraints and limited resources. Providing an in-field alternative to flame atomic absorption spectrophotometry and inductively coupled plasma optical emission spectroscopy, this entirely mobile XRF analysis method produces consistent and accurate results within minutes and at a fraction of the cost.

Jan 1, 2023

By Matthew D. Viergutz

MECS? HRS technology has reliably recovered intermediate pressure steam from sulphuric acid plants for more than 20 years. This steam can either generate electricity or replace steam produced by an existing fuel-fired boiler. As worldwide greenhouse gas emissions continue to rise, industries are looking for novel and cost effective solutions to reduce pollution, particularly carbon dioxide, from their plants. Waste heat recovery technologies such as HRS offer new and existing plants the opportunity to maximize energy efficiency while reducing their reliance on energy supply from external sources. This paper offers a unique look at energy recovery in sulphuric acid plants and how recent innovations in MECS? Heat Recovery System technology make HRS more financially viable ? and more green - than ever.

Jan 1, 2009

By Matthew D. Viergutz

MECS? HRS technology has reliably recovered intermediate pressure steam from sulphuric acid plants for more than 20 years. This steam can either generate electricity or replace steam produced by an existing fuel-fired boiler. As worldwide greenhouse gas emissions continue to rise, industries are looking for novel and cost effective solutions to reduce pollution, particularly carbon dioxide, from their plants. Waste heat recovery technologies such as HRS offer new and existing plants the opportunity to maximize energy efficiency while reducing their reliance on energy supply from external sources. This paper offers a unique look at energy recovery in sulphuric acid plants and how recent innovations in MECS? Heat Recovery System technology make HRS more financially viable ? and more green - than ever.

Jan 1, 2009

By L. von Ketelhodt

During the period October 2003 to June 2004, a containerized optical sorting pilot plant was operated at Kloof Gold Mine on a waste rock dump. In this paper, we describe the test work and its results leading to the decision to operate this pilot plant. This paper presents the operational data and financial figures achieved during this project, in particular, for the month of June 2004 when the plant was run at full capacity on three shifts, 24 hour operation. These results are also extrapolated and presented to show the profitability of such an operation at today?s gold price levels and cost structure.

Jan 1, 2009

By K. Arnold

AngloGold Ashanti has been proactive in the field of energy management for many years. AngloGold Ashanti is a signatory to South Africa?s National Energy Accord of 2005 calling for a15% reduction in energy consumption by 2015 for the mining sector. This target also supported our internal targets that were already set. AngloGold Ashanti?s seven South African mines consume on average 440 MW. Due to the dynamics of gold mines, and the large numbers of relatively small energy efficiency initiatives and awareness campaigns made measurement and verification of energy efficiency very difficult at a macro level since some initiatives could get lost in the fluctuating load profile. This paper will discuss the methodology and process followed to quantify the impacts of the combined energy efficiency initiatives at macro level. It will quantify the energy efficiency impacts in megawatt-hours (MWh), financial, and equivalent carbon emissions (CO2e) reduction with reference to our baseline year, 2004, for the Vaal River and West Wits mine clusters.

Jan 1, 2009

A project was funded by the Australian coal industry to investigate the mechanisms that might lead to sample bias when using cross-belt cutters, in order to help coal industry personnel to make better decisions about the purchase, maintenance and operation. It concentrated on DEM modelling of skew cutters. These are set at an angle to the belt with the intention of minimizing disturbance to the non-sampled material. Two bias mechanisms are likely to cause bias for cross-belt cutters. Waves of material are bulldozed off the belt by the upstream side of the body of square cutters and material is thrown by the leading edges of cutter blades for all types of cross-belt cutters. These mechanisms cause some parts of the load of material on a belt to be over-represented. The effects of these mechanisms cannot be made to be negligible, so cross-belt samplers cannot be trusted to produce unbiased samples, especially for segregated streams of material. However, it is possible to give a bound on the maximum likely bias. The grades of two portions of the stream can be estimated by stopping the belt and shovelling off 1/3 of the cross-section of the load on the belt into a container, concentrating on the final side of the belt and the top of the load. The remaining material should be put into another container and the difference in grade determined. The maximum likely bias is typically about 10% of this difference. For a cross-belt cutter, having an extraction ratio near to 100% is not a reliable indication that the cutter has little or no bias. Some bias mechanisms affecting cross-belt sample cutters make sample mass too high and some make it too low, so an extraction ratio near 100% can occur if two bias mechanisms are both active. Keywords: sampling, DEM simulation, sample bias, accuracy, precision

Jan 1, 2009

Production caving started for Lift 2 at Northparkes in August 2004. In a period of less than 3 months, more than 10 000 seismic events were recorded. Events up to local magnitude +2.9 were induced near the mine during caving, with event rates of up to 500 per day. This paper documents the seismicity related to cave initiation and cave propagation during the initial production of Lift 2. The seismogenic zone of events initially moved at a rate of about 0.5 metres per day, accelerating to 2 to 3 metres per day after a few months of cave production. Seismic data analysis infers that the crown pillar between Lift 1 and Lift 2 was destressed over a vertical height of about 100 metres. As the seismogenic zone approached the crown pillar, a macroseismic episode occurred, with more than 20 events of at least local magnitude +1 occurring in a two-week period. Based on the seismicity recorded for Lift 2 at Northparkes Mines, a caving mechanics model is proposed. Comments and suggestions are made for seismic data analysis and design of seismic monitoring systems in block caving mines.

Jan 1, 2008

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution, the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallization and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. Furthermore, the autoclave circuit invariably is a high capital cost component of the plant and an area that is carefully scrutinized when debottlenecking and capacity increases are being considered. This paper identifies a unique proven way of increasing the capacity of existing or new exothermic pressure oxidative leach autoclave circuits by as much as two or three times.

Jan 1, 2009

By F. S. Beretta

Mineral processing efficiency depends on various factors and among them includes head grade fluctuations feeding the processing plant. Head grades can fluctuate beyond an admissible range, implying in recovery decrease for the mineral of interest. Grades feeding the processing plant depend on the geological domain which is being mined and on the mining schedule. Therefore, it is necessary to keep grade variability controlled. Blending piles are an efficient alternative to reduce grade fluctuations. The main factors influencing blending efficiency are the pile size or its mass and the number of layers used to pile up. Large piles are more efficient to reduce variability, however, there are economical and operational limits associated with them. This study investigates a methodology to analyse the ideal pile size to reach an acceptable variability given the in situ grade fluctuations. Geostatistical simulations provide the means to assess grade variability using an optimized mining schedule. These block grades are used to simulate any given pile throughout the mine`s life. The methodology was illustrated using a case study to control coal ash content at a mine supplying ROM coal to a power plant. Keywords: homogenization, piles, geostatistical simulation.

Jan 1, 2009

Sampling In The Coal Industry Exploration, Mine, Met and Environmental Sampling EMMES 2005 3, 4 November 2005

Jan 1, 2005

By D. Kok

A challenge in mine planning is the optimal allocation of resources to the appropriate workplaces within the shift cycle (labour, equipment type, and other resources) in order to carry out the shift cycle activities, achieve planned production targets, and ultimately maximize production within all infrastructure constraints. Generally, detailed mine planning is done on a monthly basis at a workplace level in order to determine the production targets. The production supervisor, mine overseer, or equivalent production manager must then make the appropriate resource allocation trade-off decisions on a daily basis per shift to try and deliver to the plan and required production target. Due to the complexity and number of permutations of possible resource allocation decisions, it is impossible for a human brain to make the appropriate and optimal allocation decisions that will result in achieving the maximum or target production. These allocation decision permutations must deal with the current status of workplaces (availability, position in the cycle etc.), the status of equipment availability (available, planned maintenance, or breakdown etc.), distance between the workplaces (traveling time of equipment between workplaces, etc.) and equipment type required for that shift cycle activity. All these factors need to be taken into account in resource allocation to plan for the shift, and even during the shift if a major piece of equipment becomes unavailable or a workplace activity is not progressing as planned. This paper is a case study on how an optimization algorithm can be used to create a production planning system for optimization of resource allocation in a mechanized underground platinum operation. A business case for optimal allocation of resources is demonstrated and compared to the current manual planned allocation.

Jan 1, 2012

By Daniel W. Kappes, Pierre F. X. Mousset-Jones

"In this paper a discussion is presented of a program designed to produce a 40-day production forecast for an underground stoping system.The program is intended to be a tool for the operations department in an underground mine, and is designed to utilize data readily available from production reports. Brevity of data input, ability to revise slope conditions easily and the accuracy of starting stope status are stressed. Applicability of the program to a wide variety of sloping methods makes the program potentially useful in a large number of mines.The general functions of the program subroutines, and input and output lists are discussed. An example is also given of a stope in operation for a three-day period, which shows how the program can handle production irregularities as they arise."

Jan 1, 2014

By T. M. Russell

"Face mapping is a simple but invaluable means of geological and geotechnical data acquisition whereby intact rock properties, rock mass properties, discontinuity properties, and structural orientation can be assessed. Although traditionally done via direct contact with the mapping face through techniques such as line mapping or window mapping, remote face mapping using various digital techniques has become increasingly popular in recent years. Sishen is a large open pit mining operation requiring a comprehensive geotechnical data-set to evaluate pit wall design and stability with the necessary level of confidence. Geotechnical borehole data, face mapping data, geotechnical laboratory testing data, and implicit structural models provide the main sources of this information. Although a large geotechnical borehole database has always been maintained at the mine, face mapping has in the past been restricted to sporadic and isolated stability assessments. In 2013 the mine acquired a terrestrial laser scanner with the resolution, photographic capabilities, and software required to carry out geotechnical face mapping. A face mapping procedure was set up based on accepted face mapping methods, the data requirements of the mine, and capabilities of the laser scanner system. Mapping data obtained from the scans was integrated into the Acquire geological data management system, a purpose-designed structured query language (SQL) database system used for storing the mine’s geotechnical data. Within the geotechnical design process, having face mapping data available has improved confidence in the properties of the rock mass and structural environment, allowing for better definition of geotechnical design sectors. Overall, the face mapping and geotechnical analysis features of the terrestrial laser scanner in use make it an invaluable geotechnical data capture tool, provided a system is in place to store mapping data in a manner that allows for meaningful rock mass and structural information to be produced. IntroductionFundamental to the geotechnical design process is the acquisition of a reliable and complete geotechnical data-set. Geotechnical data acquisition will typically commence during the early stages of a project and continue well into the operational life of the mine, with the data confidence progressively increasing as the amount of data captured increases. Sishen mine currently bases all open pit geotechnical designs and geotechnical risk assessment on geotechnical borehole data in conjunction with interpreted structural models. Boreholes are logged and the data is captured in an ongoing process. This process forms the initial step in the geotechnical design and risk assessment process whereby the raw data is used to classify the strength properties for each lithology, provide inputs for geotechnical block models, and ultimately provide the inputs for slope design analyses. To date, borehole data has provided the only largescale, organized data-set for input into geotechnical analyses at Sishen. Although borehole data is the best and most comprehensive form of geotechnical data, there are some shortfalls that can be addressed by other data collection methods. These shortfalls are as follows."

Jan 1, 2018

By E. L. J. Kleynhans, J. I. J. Fick, J. P. Beukes, P. G. van Zyl

"Ferrochrome (FeCr) is vital for the production of stainless and high-alloy ferritic steels, since it is the only source of new Cr units. FeCr production is an energy-intensive process. The pelletized chromite prereduction process is most likely the FeCr production process with the lowest specific electricity consumption (SEC), i.e. MWh/t, currently in operation. However, due to increases in costs, efficiency, and environmental pressures, FeCr producers are attempting to lower their overall energy consumption even further. Recently, it was proven that pre-oxidation of chromite ore prior to pelletization and prereduction significantly decreases both the SEC and lumpy carbonaceous reductants required for smelting. This paper presents the first attempt at conceptualizing the technoeconomic feasibility of integrating chromite pre-oxidation into the prereduction process. Financial modelling yielded a net present value (NPV) at a 10% discount rate of approximately R900 million and an internal rate of return (IRR) of approximatelyy 30.5% after tax, suggesting that the implementation of pre-oxidation prior to pellet prereduction may be financially viable. Sensitivity analysis indicated that the parameter with the greatest influence on project NPV and IRR is the level of prereduction. This indicates that the relationship between maintaining the optimum pre-oxidation temperature and the degree of prereduction is critical for maximium process efficiency. IntroductionStainless steel is a crucial alloy in modern society. Virgin chromium (Cr) units used in the manufacturing of stainless steel are obtained from ferrochrome (FeCr) – a relatively crude alloy consisting predominantly of Cr and iron (Fe) (Murthy, Tripathy, and Kumar, 2011; Beukes, van Zyl, and Ras, 2012). FeCr is produced mainly by the carbothermic reduction of chromite ore in submerged arc furnaces (SAFs) and direct current arc furnaces (DCFs) (Neizel et al., 2013; Beukes, Dawson, and van Zyl, 2010; Dwarapudi et al., 2013). The energy required to heat, smelt, and reduce the chromite ore to the metallized state is supplied by electricity (Pan, 2013). FeCr production is an energy-intensive process, with a specific electricity consumption (SEC) varying from 2.4 MWh/t to more than 4.0 MWh/t FeCr produced, depending on the process applied (Pan, 2013; Neizel et al., 2013). Daavittila, Honkaniemi, and Jokinen (2004) stated that the typical operational costs of FeCr smelters can be divided into four categories, i.e. chromite ore (30%), carbonaceous reductant (20%), electricity (30%), and other production costs (20%). This makes electricity consumption the joint largest factor that influences operational costs in FeCr production."

Jan 1, 2017