Search Documents

By P. E. L. Balestra, A. O. Filmer

The kinetics of the reactions involved in the non-oxidative dissolution of nickel concentrate in hydrochloric acid were studied by electrochemical and powder-leaching methods. It was found that the rate of non-oxidative dissolution increases with a cathodic shift in the mixed potential, which can be achieved by an increase in the nickel-to-sulphur stoichiometric ratio at the reaction surface. An unactivated concentrate with a sulphur content of 36 per cent exhibited a mixed potential of +O,3V (SCE) and could not be leached satisfactorily in 3 M hydrochloric acid at 60°c. When activated material (18 per cent sulphur) was leached, it had a mixed potential of -O,3V, and high iron and nickel extraction rates. Results reported by other workers on the non-oxidative dissolution of sulphides are explained in terms of the mixed potentials at which dissolution occurs.

Jan 1, 1981

By I. B. Fernandes, M. A. Reuter, A. Abadias Llamas

Metallurgical simulation and evaluation of the resource efficiency of whole production processes are of key importance for impact assessment, in terms of environment and resources. Exergy is a measure of resource consumption, taking into account energy, raw materials, water, and chemicals; which allows for the evaluation of different technologies to find the most resource efficient and environmentally friendly process. This paper compares the sustainability for production of rare earth magnets from primary and secondary resources through an exergetic evaluation of the production process, in addition to traditional life cycle assessment (LCA). The methodology makes use of simulation tools for tracking material flow and resources used, based on thermodynamic laws, from ore exploitation to magnet production and recycling. It highlights areas with the greatest potential for improvements in terms of resource consumption and environmental impact generation, having a thermodynamic-validated flowsheet for primary and secondary production of NdFeB magnets, present in several low-carbon technologies, such as wind turbines, electric vehicles, and cooling systems. It demonstrates the minimum exergy destruction for magnet production, through an irreversibility breakdown chart, showing where irreversible material and energy losses occur. Results show that CO2-equivalent emissions for producing NdFeB permanent magnets from primary resources could be twice as high when compared to magnets produced from recycling technologies. The theoretical maximum exergetic efficiency for primary production is 57.61%, whereas for permanent magnets produced from secondary resources, the exergetic efficiency reaches up to 82.89%. Two magnet recycling technologies were evaluated, i.e. in acidic medium and via hydrogen decrepitation, and it was observed that their exergetic efficiency and environmental impact performed better than production from primary resources. Keywords: Resource efficiency, exergy analysis, permanent magnet recycling, process simulation, system design

Jan 1, 2020

By Z-B. Cheng, X-J. Liu

"Intensive mining of shallow coal seams tends to result in severe subsidence of the ground surface. Surface subsidence is a complex dynamic spatiotemporal process that constantly changes as mining advances. With Liangshuijing coal mine as a case study, 3DEC numerical software was used to simulate the development of the moving subsidence field from open-off cut to full subsidence on the working face. The results demonstrate that the formation of a subsidence field is directly related to the coal seam depth H and the extent of the mine workings. Taking the advance distance of the working face as the unit of scale, the process of surface subsidence can be divided into four stages: micro-change (H/ p), the development of surface subsidence (2H/ p), the formation of a movement subsidence field (3H/ p), and dynamic balance (4H/ p). The changing movement of a subsidence field can be fully described by the characteristics of surface subsidence value, curve slope, and the inflection position. The results provide important technical support for predicting surface subsidence and the temporal–spatial evolution features of mining subsidence. IntroductionChina’s coal output was about 3.52 Gt in 2017 (China National Coal Association, 2018), making it the largest coal producer in the world, accounting for almost half of total world coal production. Coal production and distribution play a vital role in the energy industry of China. However, entire overlying strata, from coal seam to surface, are disturbed as a result of long-term, high-intensity and large-scale mining, causing surface subsidence. This results in groundwater loss, surface desertification, vegetation loss, and mud-rock flows. These issues have become topics of common concern throughout society. According to related research results (Liu 2008), the area of surface subsidence caused by coal mining in China has reached about 600 000 ha, some 0.2 ha (and up to 0.42 ha) of surface subsidence for every 10 000 t of coal produced. Surface subsidence disasters not only damage buildings, water conservancy, transportation infrastructure, and farmland, but also cause adverse effects on individual and community lifestyles, environmental hygiene, and economic development. Deterioration of the ecological environment in mining areas has a long history and is very harmful (Lu, 2015)."

Feb 1, 2019

By C. Bergmann, V. Ross

The concept of underground ore processing, in which valuable ore and waste are separated at a coarse particle size to improve the economics of operations and minimise the environmental impact, seems attractive from a sustainability perspective. Perceived benefits of such an operation include energy and cost savings due to a reduced hoisting load, a reduced footprint of surface operations, and using material for backfill that has not been contaminated by process chemicals. Progress in the South African mining industry in this area has however been below expectation, and opportunities for underground processing in deep, narrow reef operations were therefore explored by an Excel-based simulation with sensor-based sorting (SBS) as concentration technology. Various PGM mining scenarios incorporating factors such as the mining rate, depth of operation, and effects of dilution and particle size on the metallurgical efficiency, were compared. Whilst these initial results can be regarded as indicative only, they have shown that the economics of such an operation are driven by selective mining at significantly higher rates than achievable with conventional methods. Also, the cost of preparing, conveying and placing rock backfill will need to be lower than that of hoisting waste and depositing it on a surface dump. Another aspect to be addressed is whether ore sorting machines would be able to operate under harsh conditions underground and what provision would need to be made to ensure their efficient operation. Further investigations should focus on refining costs, incorporating environmental considerations in the modelling of economics and sustainability, and compare greenfields with brownfield scenarios. Keywords: Ore sorting, hoisting, backfill, mining rate, economics simulation

Jan 1, 2020

[Council for 1994/95 President J.A. Cruise President Elect D.A.J. Ross-Watt Vice Presidents Senior P.D.K. Robinson Junior Dr N.A. Barcza Immediate Past President Dr H. Scott-Russell Honorary Treasurer D.A.J. Ross-Watt Members of Council J.P.W. Bennie Dr L.A. Cramer Prof. R.J. Dippenaar J.R. Dixon A.A.B. Douglas F.M.G. Egerton Prof. R.H. Eric B.R. Fleetwood Dr M.A. Ford Dr R.V.R. Handfield-Jones P.J. Knottenbelt R.P. Mohring K.C. Owen M.H. Rogers K.A. van Gessel P.M.T. White]

Jan 1, 1995

By M. Asghari, R. Amiri, A. Haratian, M. Noue Parast, S. Haji

Today the roller screen has a wide range of applications in the steel-making industry. It is used for screening of green pellets before using the kiln. Since the appropriate size of a green pellet is -16+9 mm, there are different gaps between rollers that make green pellets classified in three categories: -9 mm (undersize), -16+9 mm (onsize) and +16mm (oversize). The efficiency of a roller screen is specified according to the weight percent of undersize in onsize as a fine material, and weight percent of onsize in oversize (loss). This efficiency is influenced by different operational parameters such as roller diameter, roller speed, and roller gap, material type of rollers and inclination of roller screen. This study investigates the effect of different material types of rollers in efficiency of Ardakan roller screens, located in the Yazd province of Iran. The rollers of the existing roller screens in this pelletising plant are made of polyurethane which according to this investigation, has a maximum lifetime of about six months. Operating the polyurethane rollers beyond its lifetime generates serious problems such as high wear of rollers, and consequently, material buildup on the roller surface which then significantly decreases the roller screen efficiency. So, after examining different roller materials, stainless steel 304 with higher surface roughness to help pellets move properly on the roller screen surface was selected as a solution to this problem. The new roller screen was constructed by Fakoor Meghnatis Spadana (FMS) and replaced the previous one. In this way, the maximum capacity of the roller screen was increased about 17% and the roller screen efficiency was increased about 15%. Keywords: Roller screen, green pellets, efficiency, onsize, operational parameters

Jan 1, 2020

By N. Naude, L. S. Leal Filho, M. P. Tshazi

In this paper, the authors performed experiments in the Denver and Leeds laboratory flotation devices at the University of Pretoria at various particle sizes to evaluate the performance of the devices. Quartz was used in a single mineral system at discrete sizes fractions, -25 μm, +25- 45 μm, +45-75 μm, and +75-106 μm. Hydrodynamic analysis, based on dimensionless power and Reynolds numbers, indicated that the Leeds cell required higher power input to achieve comparable flow conditions. Specifically, the Leeds cell exhibited an average power number of 1.03, whereas the Denver cell averaged 0.77 within the same impeller speed range of 1000 rpm–1500 rpm. For comparative flotation performance, impeller speeds were calibrated, resulting in operating speeds of 1200 rpm for the Denver cell and 1400 rpm for the Leeds cell. The cells performed similarly at two coarser-sized fractions. However, some deviations were observed in the finer particle size range. The -25 μm (fine) fraction initially achieved a recovery of only 15%. An additional reagent dosage was required to enhance the recovery of this fraction significantly. These findings highlighted the influence of particle size on flotation recovery. For all experiments, the Denver laboratory flotation cell outperformed (defined by higher recovery) the Leeds device, while still operating at a lower impeller speed. This advantage can be attributed to its impeller-stator design and air dispersion features, effectively overcoming slurry resistance and resulting in superior flotation performance compared to the Leeds cell.

May 27, 2025

By G. C. Lindeque

"A downward trend in tyre life on haul trucks at an open pit iron ore mine prompted an investigation into the current tyre management strategy in order to improve tyre life. ‘Best practice’ was compared to the current tyre management strategy at the mine to determine aspects that could be improved. Aspects that showed significant room for improvement included employee tyre awareness, tyre pressure maintenance, and road conditions. For each of these aspects a plausible alternative was suggested.A new tyre management strategy was formulated as a step-by-step guide on how to implement the proposed changes. Each step introduces new initiatives but at the same time builds on the previous step’s success. A sensitivity analyses was performed to determine the impact of the proposed changes, with the variables being the reduction in the percentage of premature tyre failure, and the reduction of the site wear rate.The ‘most likely’ scenario showed an increase in tyre life of 41% for the Komatsu 730 trucks and 105% for the CAT 777 trucks if the entire tyre management model is implemented. This would result in a possible annual saving related to tyre usage of R9.2 million. OverviewThe study focused on the tyre life on the main haul fleet at an open pit iron ore mine. The haul fleet consisted of 17 Komatsu 730 (180 t) haul trucks and 12 CAT 777 (90 t) haul trucks.The haulage operation consists entirely of tyre-based haul trucks. Five per cent of the total mining budget is related to tyre costs. Since 2012 there has been a steady decrease in tyre life as measured in operating hours (Figure 1) due to the high percentage of tyres that fail prematurely. In 2014 a total of 41% of all tyres failed prematurely and 61% were classified as ‘worn out’."

Jan 1, 2016

By A. J. Vietti

"Drought conditions and the possible lack of sufficient raw water supply are a constant reminder to the Southern African diamond miner of the need to minimize raw (new) water input while maintaining or expanding mine throughput.Since water input volume is directly related to water output (loss) volume, mainly to the tailings, it is obviously beneficial to dewater the tailings as much as possible. However, this may not always be as easily achieved as first thought. Owing to the unique mineralogy of each kimberlite deposit and the unique chemical profile of each raw water source, dewatering of the slurry is not a standard process that can be applied equally across the entire diamond industry.This paper presents a first-step strategy that kimberlite diamond mine operators should consider and apply to meet and exceed their watersaving targets. Introduction A common metric for measuring water use efficiency in a metallurgical plant is the amount of raw water used per ton of head feed treated (m3/t). The metric includes all water recycled from the dewatering process and from the tailings storage facility (TSF), and the only inputs are tons of ROM ore and cubic metres of raw water make-up to replace water lost to evaporation, seepage, and lock-up at the TSF (Figure 1).The volume of new raw water available to the process is not unlimited and a maximum monthly allowance is typically set during the mine permitting process. Consequently, if the volume of water lost exceeds the volume of new water available or alternatively, in times of drought where the allowable volume is unavailable, the plant has no other option but to reduce throughput.However, if the plant operator is able reduce the volume of water lost to the TSF, the plant will have additional capacity to either increase tonnage throughput or sustain nameplate capacity during periods of severe drought. The obvious conclusion, therefore, is to reduce the volume of water lost to the tailings by improving the efficiency of the dewatering process (typically gravity thickening) simply by increasing the density of the tailings being discharged. In practice, however, the unique mineralogy of each kimberlite deposit and the chemical profile of the raw water source used imply that at some mine sites, solid/liquid separation (or settling) of tailings slurries at the dewatering process is more easily achieved than at others. In these cases, simple practical steps such as firstly improving the flocculant reagent make-up and dosing control, and secondly focusing on thickener discharge control, are the only requirements for enhancing water recovery at the dewatering circuit. At other mine sites however, solid/liquid separation of the tailings may not be achieved at all, in which case efforts to increase water recovery by improving reagent dosage and thickener control would be fruitless unless the colloidal properties of the thickener feed slurry are modified."

Feb 1, 2019

Dr J. P. Hugo, Pr. Eng., after obtaining a B.Sc. (Eng.) in Metallurgical Engineering at the University of the Witwatersrand in 1948, gained about 9 months' practical experience in a British steelworks, followed by post-graduate studies at Sheffield University, leading to a Ph.D. (Metallurgy) in 1953. Mr G. Y. Nisbet, Pr. Eng., holds a B.sc. (Min.) from the University of the Witwatersrand (1948) and a P.M.D. from Harvard University, U.S.A. (1966). On graduating, he was awarded the Chamber of Mines' Gold Medal. Professor D. G. Krige, holds a D.Sc. (Eng.) from the University of the Witwatersrand (1963) and a D.Ing. (H.C.) from the University of Pretoria (1981). Dr P. T. Wedepohl holds a B.Sc. (Hons.) from the University of the Witwatersrand (1953) and a Ph.D. from the University of Reading, England (1958).

Jan 1, 1984

By D. A. Holtum

On Tuesday, 10th November, 1987, The South African Institute of Mining and Metallurgy held a colloquium attended by some 120 delegates on 'On-Stream Analysis' at Mintek, Randburg. Mr John Moore, Consulting Metallurgist of Anglo American Corporation of South Africa Ltd, introduced Mr Gene Fivaz, the President- Elect of the SAIMM, who read an address by Mr B.C. Alberts, the current President. Mr Alberts was unable to attend the Colloquium owing to urgent business overseas. Opening The opening address emphasized the important role of minerals in the South African economy. In particular, it was noted that 20 per cent of the work force were employed in the minerals industry or associated industries. In recent years, production costs had risen as a result of inflation, and sanctions had had some effect on the exportation of minerals. Thus, there was continuing pressure on the industry to improve recoveries and increase efficiency.

Jan 1, 1988

By J. M. Stewart

Although the incidence of heat stroke in South African gold mines is small, work continues on its reduction. This paper proposes limits of heat stress that are applicable to South African underground conditions, with the warning that they should not be extrapolated to other situations without careful consideration having first been given to their limitations. These limits of heat stress take physical and physiological considerations into account, and they correspond to there being a 10-6 risk of an essentially nude man developing a rectal temperature in excess of 40°C. It is recommended that further work should be undertaken on the development of equations for the calculation of the heat transfer from clothed men, the derivation of equations that quantify the physiological conductance and sweat rate response of humans, and on establishing the frequency distributions that describe variations in rectal temperature response between individuals in different types of environment.

Jan 1, 1981

By J. A. Kinnaird, B. J. Youlton, K. L. Youlton

Methods for treating and processing refractory gold ores are well established. However, what is less well understood is how the formation of the gold-bearing deposits affects gold processing and extraction. In order to evaluate the effect of ore genesis on gold extraction a number of South African gold deposits were studied. These included complex Pilgrim’s Rest samples as well as refractory Fairview, Barbrook, and Consolidated Murchison samples. We found the refractory nature of gold ores is controlled by a limited number of well-understood mineralogical factors. Solid solution gold is linked to low temperature and pressure conditions in fine-grained sedimentary lithologies, while reactive pyrrhotite can form from hydrothermal fluids associated with mafic magmatic rocks. These formational controls can be used to identify and avoid complex deposits at a desktop study phase, or address and reduce complications further along the pipeline using early mineralogical studies.

Jun 1, 2021

By A. Rödfalk, P. Bloemer, J. P. Nilsson, N. Brogden

"Reliable and accurate metal transfer information during silicon tapping from an EAF is invaluable for decision-making and process optimization, while obtaining such information safely is a necessity.Elkem Thamshavn Norway, a producer of metallurgical-grade silicon, identified inherent safety problems with gauging fill levels in ladles using dip bars while molten metal was continuously pouring from a rotating EAF. Operator safety was a paramount concern, and an alternative automatic method of controlling the tapped fill level needed to be found.It was also considered that further benefits could be achieved such as monitoring the tapping flow from the EAF in order to identify any clogging, as well as the potential to use the live feed from such a system to assist decision-making regarding work around the taphole area.Agellis Group AB, Sweden, a company with over 30 years of experience in gauging molten metal levels in the metals industry, was able to design a solution for Elkem Thamshavn that would provide the required real-time process data while enhancing operator safety.This paper shows how the Agellis AB EMLI-L system was successfully installed at Elkem Thamshavn’s EAF continuous tapping area, how ladle fill levels were constantly monitored, and how full ladles were replaced by empty ones without the need for operators to be in the tapping area to take level readings. The results were used to compare the accuracy and reliability of Elkem Thamshavn’s current measuring methods with that of the EMLI-L system. The paper also covers how problems such as how to connect, run, and protect cables in and around the EAF tapping area, as well as connector and cabling survivability during the three day refractory pre-bake period, were solved. Finally, the paper discusses the potential production improvements, maintenance requirements, and data integration attainable through the installation of the system, as well as the major safety improvements that have been achieved."

Jan 1, 2014

By P. Gonzalez

Minera La Parreña, S.A. de C.V., Milpillas operation is an underground mine designed to process 8 352 tons of ore per day for the recovery of copper through crushing, heap leaching, solvent extraction and electrowinning facilities. In order to optimize copper recovery during leaching, the ore is crushed to 13 mm and subjected to primary sampling every 15 minutes for metallurgical accounting. At the same particle size, primary sample goes to secondary sampling and then, the secondary sample is crushed to 2 mm before tertiary sampling. The tertiary sample is sent to laboratory where a final sample is obtained and pulverized to 106 microns for copper assay. This paper shows a review of sampling strategy focused on minimizing or eliminating sampling errors and an experiment designed to determine copper head grade profile as well as the best sampling frequency.

Jan 1, 2009

By S. Budavari, F. M. C. C. Vieira

For several decades, the deep, gold-bearing reefs of the Witwatersrand basin have been mined predominantly according to layouts characterised by longwalls with strike pillars to provide regional support. During the past few years, a new generation of mining layouts has been introduced. These layouts are based on the concept of grid-type, scattered mining with dip pillars for regional support. As the extraction of the gold reefs extends to depths below 3500 m, the hazards associated with mining at these ultra-depths are expected to increase to unacceptable levels. Therefore, the question arises as to, which of the currently applied mining layouts is most acceptable for the economic and safe extraction of an ultra-deep orebody. The purpose of this paper is to describe a research investigation carried out to evaluate the degree of acceptability, from the rock engineering view point, of four currently used mining layouts for application at a depth-range of between 3500 and 5000 m. Pendant plusieurs décades, les filons d’or profonds du bassin du Witwatersrand ont été exploités d’une manière prédominante selon des dispositions caractérisées par des longues tailles avec des piliers directionnels pour donner un support local. Les dernières années ont vu la naissance d’une nouvelle génération de dispositions de mine. Ces dispositions sont basées sur le concept d’extraction type grille, éparpillée, avec des piliers au pendage pour le support local. Comme l’extraction des filons d’or va à des profondeurs en dessous de 3500m, il faut s’attendre à ce que les risques associés à l’exploitation à ces profondeurs extrêmes atteignent des niveaux inacceptables. Par conséquent, la question se pose de savoir laquelle des dispositions de mine couramment utilisées est la plus acceptable pour l’extraction rentable et sans danger d’un gisement ultra profond. Le but de l’étude présente est de décrire les recherches exécutées pour évaluer le degré d’acceptabilité, du point de vue d’ingénierie de roche, de quatre dispositions de mine couramment utilisées pour application à un rayon de profondeur entre 3500 et 5000m. Die tiefen, goldträchtigen Riffs des Witwatersrandbeckens wurden über einige Jahrzehnte hindurch vorwiegend nach jenen Layouts abgebaut, die von Langfrontstreben mit Schlagpfeilern charakterisiert waren, um regionale Unterstützung zu gewährleisten. Während der letzten Jahre wurde eine neue Generation von Grubenlayouts eingeführt. Diese Layouts basieren auf dem Konzept der Rasterfeld-Art, gestreuter Bergbau mit Neigungspfeilern für regionale Unterstützung. Es kann erwartet werden, daß auf Grund der Tatsache, daß sich die Extraktion der Goldriffs auf Tiefen unterhalb 3500 m verlagert, die Gefahren, die mit dem Bergbau an diesen Ultratiefen verbunden sind, sich auf ein nicht annehmbares Niveau erhöhen. Folglich erhebt sich die Frage, welche der gegenwärtig angewendete Abbaulayouts für die ökonomische und sichere Extraktion eines ultra-tiefen Erzkörpers am annehmbarsten ist. Zweck dieser Arbeit ist es, eine durchgeführte Untersuchung zu beschreiben, die vom Gesichtspunkt der Gesteinstechnik gesehen, vier gegenwärtig angewandte Abbaulayouts für den Einsatz in einem Tiefenbereich zwischen 3.500 und 5.000 m evaluiert.

Jan 1, 2003

Darwin Conference, 1984. Parkville (Australia), The Australasian Institute of Mining and Metallurgy, 1984. $AI5,00 (surface mail). Reviewer: H.A. Simonsen The theme of the Darwin Conference was 'The Mineral Potential of Northern Australia and Changing Concepts of Development', and the fifty papers that were presented commemorate the 'coming of age' of the Northern Territory of Australia. Rockbursts and seismicity in mines, edited by N.c. Gay and E.H. Wainwright. Johannesburg, The South African Institute of Mining and Metallurgy, Symposium Series no. 6, 1984.363 pp. R75,OOexcl. GST, £50, OS$65. Reviewer: E. T. Brown Black sands, by lan Morley. St Lucia (Australia), University of Queensland Press, 1981. Reviewer: P.W.J. van Rensburg Gravity concentration technology, by R.O. Burt assisted by Chris Mills. London, Elsevier Science Publishers, 1984. Volume 5 in the series Developments in Mineral Processing. Reviewer: D.A. Viljoen

Jan 1, 1985

The following diagrams should replace the Figs. 4, 5, and 6 that appeared on pages 412 and 413 of the October 1986 issue. These relate to the paper entitled' A new method for the rapid float-sink analysis of coal fines' by J-P. Franzidis and M.C. Harris Womanpower In 1981 the Publicity Committee of the Federation of Societies of Professional Engineers (FSPE) decided that one way in which the engineering manpower pool could be increased would be by the introduction of womanpower to the profession. Since then, Std 9 and 10 girls have been invited to attend the engineering winterschools held annually at the various universities under the auspices of SAFUES. Coal-mining wastes The 2nd International Symposium on the Reclamation, Treatment and Utilization of Coal Mining Wastes will be held in Nottingham (England) from 7th to 11th September, 1987.

Jan 1, 1986

The Annual General Meeting of The South African Institute of Mining and Metallurgy was held in Kelvin House on Wednesday, 18th August, 1982. Mr G. Y. Nisbet (President) was in the chair and declared the meeting open at 16h05. Obituaries President: It is my sad duty to announce the deaths of the following members of the Institute: Honorary Life Fellow J. A. Taylor ; Life Fellows J. Watt and J. J. Cairns ; Fellows J. H. Mortimer, R. R. M. Cousens, H. Clark, S. W. Hill, Dr A. Whillier, and Dr C. M. van H. van Staden; Members F. W. McElroy, V. J. Irsigler, B. J. R. Botha, and E. J. Jackson; and Associate B. V. Robertson. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, please rise and ob¬serve a few minutes of silence.

Jan 1, 1982

By Y. Zhan1, T. Moodley, M. A. H. Zahid

Mining operations are under growing pressure to improve safety and efficiency while dealing with aging infrastructure, complex processes, and workforce constraints. Although many sites are equipped with surveillance cameras and control systems, critical events often go unmonitored or under-analysed due to the lack of intelligent interpretation tools. Cameras typically act as passive recorders, requiring manual review by control room operators; a process that is labour-intensive, error-prone, and reactive. Vision AI is emerging as a transformative solution, combining computer vision and artificial intelligence to deliver real-time, actionable insights. This technology has evolved along two key phases: traditional object detection, and more recently, multimodal large language model integration. This paper presents solution architectures, deployment results, and key insights from real-world implementations across underground operations, open-pit truck-shovel operations, and smelter operations, demonstrating how Vision AI is reshaping mining operations to become safer, more efficient, and more intelligent.

Mar 6, 2026