Search Documents

By Thomas R. Bur

The order of identification and in same cases the magnitude of the elastic constants of an anisotropic material depends on the orientation of the cartesian coordinate axes with respect to a set of reference coordinate axes within the material; thus confusion will result unless standard orientations are used. In this paper the relationship between the cause (the internal fabric) and the effect (the elastic properties in this case) is discussed for single crystals and for polycrystalline and amorphous materials. While reference axes based on the cause are used in the IRE (Institute of Radio Engineers) standard for piezoelectric crystals) it is shown that a reference coordinate system that would be suitable and practical for all anisotropic polycrystalline and amorphous materials must be based directly on a three-dimensional expression of the effect. The conventions offered are similar to the IRE standards for piezoelectric crystals) but use the elastic coordinates of the wave surface which can be quite readily established experimentally as the reference coordinates.

Jan 1, 1969

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

4. Preliminary Study - Remote Seal Checker 4.1 Introduction Determination of the completeness of each individual seal at the time of its emplacement is essential for an effective remote sealing system. A satisfactory seal checking technique should provide a signal which: (1) indicates percentage completion as the seal is emplaced (2) provides a definite indication of a complete seal (3) indicates the size of the unsealed area if a complete seal is not feasible This information is required to establish the need for additional seal material, the need for additional seals, and the risk likely involved in entering the mine., In many situations it is as important to know the quality of a seal as it is to build an effective one. It is likely that with repeated use the remote sealing technique developed by Foster-Miller Associates will be sufficiently reliable and predictable to preclude the seal checking requirement. It is recommended, however, that each seal be checked during construction to insure its completeness and increase the level of confidence so necessary in reopening the mine. 4.2 Description of General Problem Several characteristics of remote mine seals are important in considering techniques for evaluating the effectiveness of these seals. These include:

Jan 1, 1973

By R. J. Matetic, D. Elsworth

The objective of this U.S. Bureau of Mines hydrologic-subsidence investigation was to evaluate the effects of longwall mining on the local ground water regime through field monitoring and numerical modeling. Field data were obtained from multiple-position borehole extensometers (MPBX's) that were used to measure subsurface displacements. Survey monuments were installed to measure mining-induced surface deformations. Numerous drawdown and recovery tests were performed to characterize hydrologic properties of the overburden strata. Coreholes were drilled above the study area to determine lithologic and strength characteristics of the overburden strata using the rock samples collected. Electronic recorders were installed on all monitoring wells to continuously monitor ground water levels in coordination with mining of the longwall panels. A combined finite element model of the deformation of overlying strata, and it's influence on ground water flow was used to define the change in local and regional water budgets. The predicted effects of the postmining ground water system determined by the model correlated well with field data collected from the field site. Without an infiltration rate added to the model, a static decrease of 3.0 m (10 ft) in water level would occur due to mining of both longwall panels and if an infiltration rate was inputted in the model, no predicted long-term effects would occur to the ground water system.

Jan 1, 1995

By Thomas V. Falkie, R. Venkataramani

1. Summary This investigation is concerned with description of the loading function at the underground coal face, and the identification of varia¬bles - geological, geometric, mechanical, and operational - that affect the loading function. The immediate objective of this work was to provide information for operations-research studies as applied to underground coal mining, and the broad objective was to provide guide¬lines for planning and equipment selection in underground coal mining. The loading function was expressed as -a statistically-developed linear mathematical model. Originally, fifteen independent variables were considered which potentially could have influenced the loading function. These variables were constructed on the basis of measurable or estima¬ble geometric and geological properties at the working face, mechanical characteristics of the mining machine, and certain operational proce¬dures of mining. The original model explained 64.0 percent of the experimental variation. The final condensed model explained 54.1 percent of the experimental variation in terms of only five indepen¬dent variables, namely: 1. Ratio: width of cut/total width of cutter 2. Ratio: height of cut/diameter of cutter 3. Total horsepower of cutter-drive motors 4. Rotation speed (RPM) of cutter 5,. A subjective estimate of machine quality and operator skill Certain limitations were found to exist in the evaluation of the variables. Principle among these limitations was the impossibility of precise measurement of tonnage loaded in certain instances.

Jan 1, 1972

Eliminate the occurrence of false fire detection alarms caused by the operation of diesel-powered vehicles in underground coal mines. Approach Fire detection systems used in underground mines are based on measurements of airborne combustion products such as carbon monoxide or smoke particles. The effectiveness and credibility of these systems can be reduced by the occurrence of false alarms that result from the operation of diesel-powered equipment, which produces the same combustion products. False alarms end up being very costly to the mine operation in terms of downtime and labor needed for verification. To improve upon current fire detection systems used in the presence of internal combustion engine products, the U.S. Bureau of Mines developed a fire detector that can discriminate between the occurrence of real mine fires and the presence of engine smoke.

Jan 1, 1989

By Mark Larson, Doug Tesarik, Joe Shoemaker, Brad Seymour

In cooperation with Cyprus Twentymile Coal Co., researchers from the National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory, conducted a study at the Foidel Creek Mine, an underground coal mine near Oak Creek, CO, to evaluate the stability of underground working conditions as a longwall advanced through a series of backfilled cross-panel entries. Instruments installed in the cross-panel entry pillars, backfill, longwall panel, and adjacent headgate entry were continuously monitored by a computerized data acquisition system as the longwall approached and advanced through the backfilled section of the panel. Data collected from these instruments were analyzed to determine the magnitude and direction of the secondary principal stress changes ahead of the longwall face, deformation and closure of the headgate entry, and stability of the cross-panel entry pillars and backfill. A three-dimensional, boundary element model was calibrated to accurately predict mining-induced stress changes and the distance they occurred ahead of the longwall face. As the longwall advanced through the backfilled entries, most of the mining-induced load was supported by the cross-panel entry pillars. The backfill provided stability for the roof and floor of the in-panel entries and also confined the entry pillars significantly improving their load-carrying capacity. Comprehensive information derived from backfill material property tests, instrument data, underground observations, and numeric modeling results document the safety and stability of the 8-Right mine through and should provide beneficial case study information for other longwall backfilling applications in the future.

By Gregory J. Chekan

As part of the initial investigation and validation of a new boundary-element formulation for stress modeling in coal mines, the underground stresses and displacements at two multiple-seam coal mines with unique stress problems were modeled and predicted. The new program, LAMODEL, calculates stresses and displacements at the seam level and at requested locations in the overburden or at the surface. Both linear elastic and nonlinear seam materials can be used, and surface effects, multiple seams, and multiple mining steps can be simulated. In order to most efficiently use LAMODEL for accurate stress prediction, the program is first calibrated to the site-specific geomechanics based on previously observed stress conditions at the mine. For this calibration process, a previously mined area is "stress mapped" by quantifying the observed pillar and strata behavior using a numerical rating system. Then, the site-specific mechanical properties in the model are adjusted to provide the best correlation between the predicted stresses and the observed underground stress rating. Once calibrated, the model is then used to predict future stress problems ahead of mining. At the two case study mines, the calibrated models showed good correlation with the observed stresses and also accurately predicted upcoming high stress areas for preventive action by the mines.

Jan 5, 1999

By John Owens, Wayne Howie, Hamid Maleki

After an analysis of the hazards of room-and-pillar retreat mining systems, it became apparent that safety could be significantly improved by considerations of (1) human factors, (2) remotely controlled mobile roof supports (MRS=s), (3) mine layout designs, and (4) ground monitoring systems. Initial studies of the effectiveness of MRS=s focused on their interaction with mine strata and evaluations of suitable measurements for detecting roof stability problems during pillar extraction. These studies indicated that overall stress distributions and strata movement were most influenced by the stiffness of coal-measure rocks and the design of mining layouts. Thus, to improve worker safety, mine layouts should be carefully designed and a pillar extraction method chosen for specific geologic and stress conditions. Pillar failure was often associated with an increase in pressure on the hydraulic gauges of the MRS, and roof failure was often preceded by rapid changes in the rate of roof-floor convergence. These studies led to development of a monitoring system that displays loading rate on an MRS in real time. A major MRS manufacturer cooperated in installing and testing the system on an MRS. New field studies focus on evaluating the performance of the system, measuring roof-floor convergence, and optimizing the safety of MRS operations through proper mine layout design.

By R. V. Ramani, V. T. Burgos, J. A. McClay

Cost Systems Cost systems are organized methods of collecting, allocating, and accumulating resource utility expressed in terms of money. There are two major spheres of cost accumulation: financial accounting and cost accounting. Financial accounting deals primarily with historical costs and provides a means of measuring and recording cost events which have al¬ready taken place. While there are no legal requirements to control the methods of recording and reporting cost data in the United States, the procedures in use are guided by professional organizations such as the American Institute of Certified Public Accountants. The final pro¬ducts of financial accounting practices are the income statement and balance sheet which describe the financial status of the organization under study. Cost or managerial accounting is an expansion of financial ac¬counting procedures, providing more detailed cost breakdowns on present operations with one objective being the projection of present costs into the future. The projection process tends to limit the accuracy of the information; however, to management and project justification per¬sonnel, data on future operations tends to be of greater value. The basic principle behind cost accounting is the cost cycle. As products are developed from raw materials, the value of the work-in¬process increases due to the cost input of the various fabricating ele¬ments. Thus, from the basic input elements of facilities, labor, and raw materials, costs are added to each unit of production as a function of the work performed on that unit.

Jan 1, 1975

To rapidly limit and interrupt high dc fault currents with minimal arcing in the mine atmosphere. Approach Design a dc switching sys-tem which uses a pressurized, liquid metal-filled, change-of-state device combined with a conventional interrupter and commutating switch. Direct Current Interruption Switching and interruption of large direct currents imposes severe loads on fuses, contactors, and circuit breakers in mine power systems. This problem is much more pronounced with de than with ac because of the lack of a natural current zero in dc. Dc interruption is characterized by persistent arcing that can foul contact tips and con-tribute to interrupter failures. To reduce maintenance and prolong the service life of these units, a commercially viable dc switching system has been developed by the Bureau of Mines through a research contract with the University of Pittsburgh. This system rapidly limits and interrupts high fault currents when used in combination with conventional interrupters.

Jan 1, 1983

By Peter Kovalchikb, Gregory Colec, Syd Peng, R. J. Matetic, Jeffrey Petersond

Mine Safety and Health Administration (MSHA) data indicates that the roof bolting machine is third among all equipment and second among equipment in underground coal mining whose operators exceed the MSHA-PEL (Mine Safety and Health Administration-Permissible Exposure Limit). In response to this, the National Institute for Occupational Safety and Health (NIOSH) has conducted a study to reduce overexposures of noise to operators of roof bolting machines. An important segment of the research is to determine, characterize and measure sound power levels radiated by a roof bolting machine during different drilling configurations. The determined sound power levels generated during the drilling cycle are of major interest because the levels represent the overall sound power generated by the machine. These sound power levels, determined from laboratory tests, can be used to accurately assess the effectiveness of proposed controls for reducing noise exposure to roof bolting machine operators. By using the sound power level results obtained from the laboratory and a commercially available acoustical modeling package, a method for predicting sound pressure levels to roof bolting machine operators for differing drilling types and parameters could be determined. This paper provides a method for predicting sound pressure levels at the operator’s position of a roof bolting machine in an underground coal mine using sound power levels determined in the laboratory. To determine validity, underground coal mine data was also collected to compare predicted and measured sound pressure levels. The results of the predicted sound pressure level data were the same as the underground measured results. This research will provide the mining industry with a valid method for predicting a roof bolting machine operator’s noise dosage underground given any type of drilling configuration or drilling method utilized from laboratory testing.

By W. E. Lamont

The Bureau of Mines conducted flotation tests on a mixture of barite waste materials from Nevada in which essentially all of the barite values were finer than 20 micrometers. Flotation variables investigated in these tests were the effects of (1) sodium silicate as a pulp dispersant, (2) sodium hydroxide as a pH modifier, (3) increased amounts of sodium cetyl sulfate, (4) conditioning time and (5) solids content during conditioning. The optimum flotation conditions were achieved by adding 2.5 pounds of sodium silicate and 10 pounds of sodium cetyl sulfate per ton of feed and conditioning the pulp for 20 minutes at a 35-percent solids content. Using these conditions, a concentrate was produced that contained 94.7 percent BaS04, with an attendant recovery of 90.9 percent of the barite in the feed. In addition to the flotation tests, a selective barite flocculation process was developed to treat extremely fine barite. A barite concentrate containing 96.5 percent BaS04 with an attendant recovery of 82.1 percent of the barite was produced by selective flocculation. A process patent application has been filed based on this process.

Jan 1, 1982

By A. L. Engel

This report describes laboratory-scale experimental treatment of six base-metal ore samples taken by engineers of the Bureau of Mines, Region II, while investigating ore deposits in California and Nevada. The information is of interest in developing the mining districts represented or when similar ores from other sources are being studied. Simple treatment methods were employed as far as possible. More complex treatments also were tried when necessary. The possibilities and limitations of the methods applied to the several ores are shown by the data herein reported.

Jan 1, 1960

At the present time many coal preparation plants handle coal-clay wastes in one of two methods. In one method, the waste is processed in a thickener, followed by further dewatering through filtration, and subsequent blending with coarse waste refuse from the preparation plant. The resulting mixture is then disposed by stacking it in available storage locations. The coal-clay waste is often reslurried by rain or water from other sources, causing a potentially unsafe situation such as mud flows. The other method often used requires thickening and impoundment of the thickened slurry behind earthen dams which poses safety risks if structural failure of the dams occurs. To overcome these two problems, a flocculation method was developed which produces a stable agglomerated material resistant to reslurrying. How It Works The new method involves treating coal-clay waste with lime to raise the pH and flocculating the slurry with a nontoxic polymer of polyethylene oxide. The resulting floes are dewatered on a static screen and agglomerated. For extremely fine waste, further dewatering of the material is accomplished on a rotary trammel screen. The dewatered material may be ponded or mixed with coarse waste from the preparation plant to produce a stable mixture that can be stacked.

Jan 1, 1985

By C. P. Fang

"For lower stages of multinozzle micro-orifice impactors, as many as two thousand nozzles are uniformly arranged within a cluster diameter of 1.06 inches. In the impaction region the mass flowrate of the spent air increases along the radius and reaches a maximum at the periphery. This crossflow can significantly deflect the air jets of the outer nozzles, hence the characteristics of impaction changes.Investigators in heat transfer and fluid mechanics have studied the influence of crossflow on jet deflection and found the dimensionless deflection of the jet centerline X/Dn is a function of (S/Dn)(l/m) . only, here X is downstream coordinate measured from the center of the jet orifice, Sis the jet-to-plate distance, Dn is the orifice diameter and m is the jet/crossflow mass flux ratio defined as:"

Jan 1, 1989

By W. C. Smith

The U.S. Bureau of Mines examined previous research on rib stability in an effort to develop a practical approach to understanding, characterizing, and controlling weak rib conditions in underground coal mines. Because success in stabilizing ribs depends on a basic knowledge of how weak ribs behave, the report reviews the mechanics of rib failure and the relationship of coal mine geology and pillar constraint to rib instability. Strategies for choosing an effective method of rib support are considered, and various rib support methods are discussed. Finally, the report documents techniques for monitoring ribs and use of models to assess rib stability; such monitoring and modeling can also help determine the most effective method for roof support.

Jan 1, 1992

By Robert H. Peters, George R. Bockosh, Barbara Fotta

This paper was commissioned by the Japan Technical Cooperation Center for Coal Resources Development. It is to be published in a proceedings following a series of presentations to Japanese coal officials in February 1997. The paper focuses primarily on summarizing the past 20 years of U.S. research on promising techniques for ensuring that underground coal miners work safely. These techniques can be grouped into three major categories: management, workplace design, and training. Each technique is described, and the results of efforts to apply the technique at underground coal mines are summarized. Recent statistics on accidents and productivity in U.S. underground coal mining operations are presented before the overview of research findings is given. Because Japanese coal mines are using the longwall method of coal extraction, separate statistics are given for U.S. longwall versus room-and-pillar coal mining operations.

By Margaret R. Egan

In an underground mine fire, a toxic mixture of combustion product gases and particulate matter is transported by the ventilating system endangering everyone downstream. To determine the magnitude of the problem that these toxic combustion products pose, the U.S. Bureau of Mines is investigating the combustion products of typical materials found in underground mines. The total toxicity of the combustion products depends upon the evolving gas species and particulate matter, the amount of material involved, and the ventilation rate. In a simulated mine environment, the products from smoldering poly- vinyl chloride (PVC) brattice and conveyor belting were analyzed for gas concentrations and smoke characteristics. The primary toxic gases are hydrogen chloride (HC1) and carbon monoxide (CO). Smoldering conveyor belts are more detectable than smoldering PVC brattice cloths. These results, combined with previous analyses, are used to estimate relative toxicities, product levels, and detect-ability of smoldering mine combustibles.

Jan 1, 1992

By Kathleen M. Kowalski-Trakofler

This paper discusses human judgment and decision making under stress. The authors review selected recent literature across various disciplines and suggest a definition of stress within the context of decision making during the management of emergencies. They also discuss fieldwork by the Pittsburgh Research Laboratory, NIOSH, which explores traumatic incident stress, the relationship between previous training and performance under stressful conditions, and human behaviour in underground mine fires. The authors assert that stress is one of the factors that decision makers must contend with in most life-or-death situations. They suggest that a better understanding of individual judgment and decision making activities whilst under stress would yield a better understanding of how people reach the choices they make in emergencies. This enhanced understanding would be of enormous value to emergency managers, researchers and policymakers.

Jan 1, 2003

By W. A. Heitbrink, J. D. Ashley, R. E. Gresh, J. A. Organiscak, A. B. Cecala

Many different types of mobile equipment used in surface coal mining utilize enclosed cabs to protect equipment operators. The overburden removal process is extremely dusty and can cause excessive exposure to respirable dust, especially crystalline silica. After equipment is used for years, many components of the enclosure deteriorate and its effectiveness is greatly reduced. This report discusses a cooperative research study performed on an Ingersoll Rand DM45E surface drill, retrofitted with a new Sigma pressurization and filtration system. Respirable dust concentrations were substantially reduced from 0.64 mg/m3 during pre-testing to 0.05 mg/m3 during post-testing with the new system, representing a 92% reduction in dust levels in the drill cab. This new system appears to be a very well-built and sturdy device, well-suited for the mining industry.