Search Documents

[ ]

Jan 1, 2011

Improve the effectiveness of face ventilation systems in coal mines by minimizing leakage around line and check curtains. Approach In-mine surveys were conducted to determine current curtain construction techniques, their effectiveness and associated costs. In addition, performance characteristics of extensible curtains were evaluated. A total of 77 conventional curtains in 10 mines was examined for 12 important characteristics. Extensible curtains were erected in a full-scale model and examined for operational difficulties, effects of leakage, and air pressure. Survey Results The underground mine study identified four categories of face brattice construction ranging from simple to complex: 1. Simple suspension of the curtain from roof bolts with the bottom edge lying on floor. 2. Spadding of the curtain to the roof on about 12-inch centers and stabilization of the bottom edge with wood or rock. 3. Use of vertical props and spads with a base board for support on the bottom. 4. Use of vertical props with caps and bottom boards plus horizontal brattice support boards.

Jan 1, 1984

By T. T. Campbell

This report describes the development of new electroplating baths from which tin-nickel alloy plate was deposited. Although tin-nickel plate can be deposited from an aqueous ammonium bifluoride bath, the corrosive nature of this bath has served as a deterrent to its use. The Bureau of Mines felt that more general acceptance of this new alloy plate would follow if neutral or alkaline baths could be developed. Promising results were obtained from electrolytes containing both tin and nickel chlorides dissolved in triethanolamine-hydrochloric acid or in ethylene glycol hydrochloric acid baths. Current efficiencies close to 100 percent were obtained with these baths. Research revealed that tin-nickel plate could be produced from organic solvents or from mixed aqueous-organic electrolytes. The composition of the alloy deposit - 65 percent tin and 35 percent nickel - was found to exhibit the same single-phase structure that is obtained from the commercially accepted fluoride-type bath.

Jan 1, 1959

By D. Cummins

This Information Circular presents a brief history of the lead-acid battery and describes ways to prevent serious injury from battery explosions when servicing and charging lead-acid batteries, particularly in the surface mining industry. The Mining Safety and Health Administration (MSHA), U.S. Consumer Product Safety Commission, battery manufacturers, and the mining industry have all contributed information as well as recommendations for injury-free handling for this report.

Jan 1, 1980

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal nonfuel mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines. Because of inadequacies in the statistics available, some series deviate from the foregoing definition. For gold, silver, copper, lead, zinc, and tin, the quantities are recorded on a mine basis (as the recoverable content of ore sold or treated). However, the values assigned to these quantities are based on the average selling price of refined metal, not the mine value. Mercury is measured as recovered metal and valued at the average New York price for the metal.

Jan 1, 1981

By Wesley A. Grosh

The Sutherland copper prospect is situated in Floyd County, Va. The immediate area was prospected around 1850, and one of the adits possibly dates from that time. Little or no ore has been mined from the deposit. The deposit is a mineralized sulfide zone occurring in mica schist and consisting mostly of pyrrhotite with minor amount of copper. A magnetometer survey of the deposit by the American Metal Co. in 1939 showed an anomaly that was thought to indicate a zone: of secondary enrichment. The Bureau of Mines diamond-drilled 14 holes, totaling 913 feet, and opened an adit during February and March 1943. No appreciable copper values or indications of secondary enrichment were found.

Jan 1, 1948

By D. E. Ingersoll

This report describes the preparation characteristics of anthracite from the Mammoth and Holmes veins in Schuylkill County, Pa., as determined by the Federal Bureau of Mines laboratory separations at specific gravities of 1.50 to 1.90. The Holmes vein anthracite contains approximately 13 percent ash, and the Mammoth vein contains about 9 percent as fed to the breaker. Crushing Broken, Egg, and Stove sizes from each vein produces Pea-size anthracite of lower ash content than that contained in Buckwheat No.1 size and smaller. The Buck-wheat No.5 size has the highest ash content of all the sizes examined. Potential recovery from a mixture of the two veins as received at the breaker, separated at 1.90 specific gravity, is approximately 64 percent of the feed at 11.0 percent ash. The same materials separated at 1.80 specific gravity yield about 61 percent with an ash content of 10.1 percent. All rejects are from the Holmes vein, because the entire Mammoth material is less than 10.0 percent ash.

Jan 1, 1960

By G. F. Kuncir

The funding tables included in this report were defined in support of an evaluation of the Advancing Oil Sale Mining Technology Program undertaken by The Aerospace Corporation. Because of the sensitive nature of the fiscal planning information, the tables have been separated from the main analysis report and given a limited distribution.

Jan 1, 1977

Engineering controls for overburden drilling include dry dust collection systems, wet dust suppression systems, and enclosed cabs [Zimmer and Lueck 1986; Volkwein et al. 1979]. Proper maintenance of the dust suppression system is critically important for drills using dry dust suppression methods. Failure to rigorously maintain these systems will result in inadequate dust control. Acute silicosis has been reported in miners operating equipment that relies on dry dust suppression [NOSH 1992].

Jan 1, 1997

By Marvin L. Whisman

A radiotracer technique developed by the Bureau of Mines extends to the parts-per-billion range the sensitivity for determining contributors of deposits formed in stored and thermally stressed jet fuels. The method depends upon measuring radioactivity associated with thermally induced deposits from fuels containing one labeled compound. The technique was applied to 88 test blends, representing 12 fuels and nine carbon-l4 labeled fuel constituents or fuel additives, or both. Data from results of these tests are included in this report. With this radiotracer technique, the contribution of fuel components and additives to thermally induced deposits in a variety of fuel environments was estimated before and after storage.

Jan 1, 1969

By W. W. Weller

This report provides low-temperature heat-capacity data and entropies at 298.15° K. for magnesium metavanadate (MgV206) and magnesium pyrovanadate (Mg2V207). The work completes low-temperature measurements planned for alkaline-earth vanadates; an earlier report dealt with calcium vanadates.4 No similar data for these compounds have been published previously. Free energy of formation values at 298.15° K. were derived by combination of the present entropy values with heat of formation data. MATERIALS The materials used in the measurements were portions of the samples described in a previous Bureau of Mines publication by King, Koehler and Adami.5 Methods of preparation, chemical analyses, and X-ray examinations are covered in this paper. The indicated purity of the samples was 99.9 pct.

Jan 1, 1962

Measure the leakage through individual crosscut stoppings quickly and economically so that the worst ones can be identified and repaired. (Typically 60 to 80% of the air supplied to a mine short circuits before reaching a working face.) Approach Most of the leakage through a permanent stop-ping is channeled through two windows in a temporary stopping, and air velocities through the windows are measured; leakage is determined from a formula. How It Works A temporary stopping made of plastic brattice is erected in the same cross cut as the permanent stopping, either upstream or downstream. The brattice is fastened to the roof, bottom, and ribs of the entry with spads. Normal leakage of brattice was allowed for in deriving formula, and does not effect results. For best accuracy the brattice and the stopping should be separated by a distance of one hydraulic diameter.

Jan 1, 1979

By B. E. Blair

Accelerometers of various types, velocity gages, and a displacement meter are shown to give reliable date when measuring seismic pulses generated in rock by the detonation of explosive charges. Displacement and velocity records are differentiated and shown to compare with velocity and acceleration records. Velocity and acceleration records are integrated and shown to compare with displacement and velocity records, respectively. The experimental data are shown to satisfy the scaling laws developed by dimensional analysis. Propagation laws are developed for peak amplitudes of the first pulse of displacement, velocity, and acceleration. These propagation laws are shown to be independent of the gage used to obtain the data. As a result, the usefulness of the various gage types can be extended. For example, accelerometers, because of their high frequency and amplitude limits, can be employed near the shot to measure acceleration and/or velocity (by integration), Velocity gages, because of their higher sensitivity, can be employed at relatively larger distances from the shot to measure velocity and displacement or acceleration (by integration or differentiation).

Jan 1, 1954

By William P. Diamond

A 3-inch pilot hole was directionally drilled to intercept the Freeport coalbed horizon horizontally at Mather, Pa., as part of a Bureau of Mines degasification project. The original concept was to continue the horizontal drilling into the coalbed, after the initial intercept, with a total of three horizontal holes eventually being completed. However, the erratic thickness (0.0 to 4.3 feet) of the Freeport coalbed at Mather was not sufficient to support the horizontal drilling degasification technique, and the site was abandoned after six attempts to locate adequate continuous coal thicknesses. The drilling of coreholes in the immediate vicinity of proposed well paths to evaluate coal thickness is essential prior to future slant hole operations. Although mechanical failures of the new directional drilling equipment, mud pump and rig breakdowns, directional control problems, and exploratory horizontal drilling in the Freeport horizon more than doubled the anticipated cost of the pilot hole, continuing improvements in directional drilling equipment and techniques should significantly reduce the time and costs of future drilling operations.

Jan 1, 1977

To develop an explosive charge that will effectively break rock in underground mines and that can be safely fired without the use of blast-holes or the need for stemming. Approach The Bureau of Mines developed a non-incendive, cylindrically-shaped explosive charge that will not ignite gassy or dusty atmospheres, even methane-laden air. How It Works Firing unconfined explosive charges in underground mines is prohibited by law since detonation in gassy or dusty atmospheres is extremely dangerous. However, there are advantages in using unconfined charges from both a safety and a production standpoint. Explosives can effectively break up large boulders, rocks and slabs when leveling roof falls and can dislodge overhangs which miners would other-wise have to dislodge manually, exposing themselves to

Jan 1, 1983

By A. T. Iannacchione

Designing coal pillars to provide resistance against overburden and gob loads has long been an aim of rock mechanics engineers. This requirement has become more imperative as greater overburdens are encountered and when mining in stiff coal-bearing strata. Current design procedures rely on theories of coal pillar behavior that take into consideration a common hypothesis. This hypothesis states that the elastic core is surrounded by an inelastic yield zone. The distribution of stress at low-to-moderate pillar loads has been effectively defined by this hypothesis. However, it suffers greatly when applied to large width-to-height (w/h >lo) coal pillars under considerable overburden (>500 m) . In these situations, the hypothesis says the elastic core can achieve unrealistic stress states giving the pillars extremely high calculated strength. A growing body of field studies has shown this is not the case. It has become clear that same other mechanism must be involved. It is the purpose of this paper to discuss the importance of an interface slip mechanism between the coal- bed and the surrounding strata in controlling the extent and pattern of stresses and deformations in a coal pillar.

The U.S. Department of Labor?s Mine Safety and Health Administration (MSHA),through its winter alert program, warns U.S. mine operators and miners at underground coal mines of workplace hazards that can arise when the weather turns colder. MSHA records indicate that, historically, most explosions in underground coal mines occur during winter months. ?The changes in weather can increase the risk of fatal accidents,? says David G. Dye, Acting Assistant Secretary of Labor for Mine Safety and Health. ?Each miner and mine operator must take individual responsibility to eliminate the kinds of hazards that can cause fatal accidents in the workplace. Safety is not the other guy?s job?safety begins with you.? In fact, MSHA?s slogan for this year?s campaign is ?Winter Alert Starts Now and Safety Begins with YOU.? This message reminds miners and mine operators of the risks of colder weather and educates them about helping to reduce risks and hazards. ?Safety requires the joint effort of both management and labor,? Dye says. ?Everyone at the mine site must see safety as an individual value and act to ensure a safe working environment.?

Jan 1, 2006

By I. L. Nichols

Laboratory characterization studies have investigated the processing variability of carbonaceous uranium-bearing materials found in-sandstone deposits. This work was conducted by the Federal Bureau of Mines in support of its goal to maintain an adequate supply of minerals to meet national economic and strategic needs. Conventional processing produces only partial uranium recovery from these ore materials. Ore samples from New Mexico, Texas, and Wyoming were examined, and each responded differently. Using direct acid leaching techniques, some of the ores required acid additions of only 50 pounds per ton, while others required 300 pounds per ton of material. Maximum extractions ranged from 83 to 94 percent in the six ores tested. Roasting those ores prior to leaching improved extraction of the uranium to the 90 to 99 percent range. An oxidative autoclave treatment used with five of these ores resulted in extraction of 78 to 97 percent of the uranium. The experimental studies also showed that some carbonaceous materials can be concentrated by froth flotation. The flotation tailings were amenable to acid leaching, and up to 98 percent of the uranium was extracted from this type of material.

Jan 1, 1979

By Maria I. De Rosa

Table 1 and figure 1 show the number of fires and fire in¬juries that occurred in underground coal mines by state during 1990-1999. Table 1 also shows by state the risk rates, employ¬ees' working hours, lost workdays, and coal production. Over¬all, 87 fires occurred in 12 states. Twenty-seven of those fires caused 34 injuries (the yearly average was 8.7 fires and 3.4 injuries). One fire and one injury involved a contractor. The underground mine fires required 25 mine rescue team interventions and 30 mine/section evacuations followed by 13 mine/section sealing/flooding/CO2/N2, gas injections. The Ewhr value was 1,003 x 106 hr (In = 0.007), the CP value was 4,008 x 106 st (Frr = 0.022), and the LWD value was 208. Virginia had the most fires (15 fires and 7 injuries). Pennsyl¬vania had the most fire injuries (12 fires and 9 injuries), fol¬lowed by Kentucky (12 fires and 6 injuries), and Alabama (12 fires and 4 injuries). Among these states, Alabama had the highest fire risk rate value (Frr = 0.073), whereas Pennsylvania had the highest injury risk rate value (In = 0.016). Table 2, partly illustrated in figure 2, shows by time period the number of fires, fire injuries, risk rates, employees' working hours, lost workdays, and coal production. The number of fires and fire injuries show a decrease followed by an increase during the five time periods (see table 2 and figure 2). This was ac¬companied by a decline in employees' working hours throughout the periods and an overall small decrease in coal production. The In and Frr values follow patterns similar to those shown by the fire and injury values. By comparison, data from Pomroy and Carigiet [1995] show that during 1978-1992 a total of 11 states were involved in 164 underground coal mine fires (yearly average, 10.8) with 43 injuries (yearly average, 2.9) and 27 fatalities (yearly average, 2; however, the 27 deaths occurred during a single fire caused by an overheated air compressor [MSHA 1984]). The CP value was 5,340 x 106 st (yearly average, 356 x 106 st) (Fn = 0.031). Data on employees' working hours and injury risk rates were not available. Tables 3-8 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 3 shows the major variables during 1990-1999. Table 9 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By S. R. Zimmerley, John Gross

"The investigation discussed in this paper was undertaken to obtain fundamental data on crushing and grinding and has been confined, so far, to work on quartz.The results of crushing or grinding have hitherto been judged entirely by the amount of the various-sized particles produced, based. on sieve sizing for particles above 74 microns in size and on microscopic measurement or elutriation for particles below 74 microns - a method which could give only a general idea of what had been accomplished.There was a distinct need of a ""yardstick"" for the measurement of crushed material. It appeared that no advance in the fundamental investigation of crushing and grinding could be made without a reliable method of surface measurement and that such a measurement would have to be based on some property of the surface of the crushed material.A number of attempts based on various surface actions, such as adsorption and heat of wetting, were made to measure surface on quartz particles, but all gave unsatisfactory results. After some preliminary work it was decided that a dissolution method based on Wenzel's law-- ""the reaction velocity between solids and liquids is proportional to the area. of contact""4 -- would be the most feasible.Early use of the dissolution method had been made for surface measurements5, and lately Dr. Geoffrey Martin and his coworkers in England used the dissolution method to determine surface on quartz. They compared the amount of quartz dissolved from a sample in one hour by a hydrofluoric acid solution, with the amountdissolved from a measured quartz cuboid6,After investigating the solvent power of sodium carbonate, sodium hydroxide, and hydrofluoric acid for quartz, hydrofluoric acid was selected as the most suitable solvent, and a dissolution method was developed which gives very reliable results.During the dissolution of quartz in hydrofluoric acid, the reaction velocity changes for two reasons: there is a change in concentration of solution, and a change of surface of the solid. The amount of quartz dissolved in a definite period of time is therefore not a true measure of surface. If, however, the reaction velocity or rate of dissolution for various periods of time be plotted, a curve will be obtained which, if extrapolated to the zero time ordinate, will give the rate of dissolution before any change of surface or any change in the solvent has taken place, and which is a true index of surface. This rate of dissolution, expressed in percentage of the original sample at the zero time ordinate, is designated herein as the ""Initial Rate"" or as simply ""I. R."""

Jul 1, 1928