Search Documents

By A. Dale Marcy, Pamela L. Drake

Workers who perform routine welding tasks are potentially exposed to fume that may contain manganese. Manganese may cause respiratory problems and is implicated in causing the occurrence of Parkinson-like symptoms. In this study, a field colorimetric method for extracting and measuring manganese in welding fume was developed. The method uses ultrasonic extraction with an acidic hydrogen peroxide solution to extract welding fume collected on polyvinyl chloride filters. Commercially available pre-packaged reagents are used to produce a colored solution, created by a reaction of manganese(II) with 1-(2-pyridylazo)-2-naphthol. Absorbance measurements are then made using a portable spectrophotometer. The method detection limit and limit of quantification (LOQ) were 5.2 mg filter-1 and 17 mg filter-1, respectively, with a dynamic range up to 400 mg filter-1. When the results are above the LOQ for the colorimetric method, the manganese masses are equivalent to those measured by the International Organization for Standardization Method 15202-2, which employs a strong acid digestion and analysis using inductively coupled plasma-optical emission spectrometry.

By D. S. DeLong, A. Giza, D. G. Fraser, V. A. Robinson, T. B. Whitmoyer, J. E. Sneckenberger

"A cotton dust animal exposure system has been modified to incorporate a microcomputer feedback loop to monitor particle concentrations. The loop's major components are a minature real-time aerosol monitor (miniram) to estimate concentrations and a microcomputer to read the miniram's data and to control a stepper motor that adjusts the amount of dilutant air mixing with respirable cotton dust. Ninety minute trials of this system indicate that the standard deviation of particle concentrations is within 0.68 Mg/m3 of the average concentration, insuring a near constant concentration of respirable dust throughout the exposure.INTRODUCTION Previous workWeyel et al. (1984) have determined that respirable cotton dust can be shaken from bulk cotton samples using acoustical energy. The particle generator designed to utilize this fact operates like a commercially available sonic sifter, but on a much larger scale.While this generator successfully resuspended trapped respirable cotton dust, the generator output concentration decreased exponentially with time. This disadvantage was solved by Frazer et al. (1986) by operating the generator with a sinusoidal voltage near the minimum resonance frequency of the generator. This adjustment enabled the generator to produce respirable cotton dust for six hours or longer.Frazer et al. (1987) utilized the modified acoustical generator to produce a cotton dust animal exposure system. The cotton dust concentrations were estimated by a miniram, a light scattering aerosol Monitor. The system operator used the miniram values to adjust the system's parameters to maintain the desired concentration level.PurposeThe objective of this study was to introduce a computerized feedback loop to the operator controlled cotton dust animal exposure system. The miniram's estimates were analyzed by a microcomputer to determine what adjustments in the flow of dilutant air were necessary to maintain the desired cotton dust concentration. These modifications were intended to improve system performance and ease the system operator's work burden."

Jan 1, 1988

By Edward L. McHugh

Digital camera and computer technologies can be used to monitor mine slopes and provide real-time warning of rock falls. NIOSH researchers assembled a surveillance system using low-cost video cameras and computer software from the security industry to test its effectiveness. The system is designed to signal an alarm when motion is detected and to record images of the scene. Masking can restrict motion detection to specific areas within the camera view; sensitivity is adjustable. The time-stamped images provide a record that can help reconstruct and quantify an event. Video motion detection can augment standard monitoring methods to increase safety in surface mines.

This Bureau of Mines report summarizes the research, development, and evaluation demonstrations conducted by the Bureau of Mines under the Health and Safety Act of 1969 to improve the means of notifying miners underground, who are away from their own phone, that they are being called.

Jan 1, 1977

By G. E. McClelland

During the 1970?s, the Bureau of Mines investigated a particle agglomeration technique for improving the flow of leaching solution through heaps of clayey or crushed, low-grade gold-silver ores, wastes, and tailings. This technology has been adopted on a broad scale by the precious-metals-processing industry. This report presents information on five commercial operations that have benefited from agglomeration technology and that represent a cross section of current heap leaching practice. The technology is cost effective because of decreased leach times and improved precious metal recoveries.

Jan 1, 1983

By D. B. Taliaferro, David M. Logan

which an operator may obtain detailed information regarding all projects in the State. It is the purpose of this report to present data such as volume of oil produced monthly, volume of water injected monthly, spacing of wells, number of injection wells and oil wells, and other such pertinent information regarding every project in the State whether active or abandoned and whether a success or a failure. It is believed that with these data it is possible to analyze water-flooding operations in this area more completely than has been possible in the past. As the title indicates, the report is essentially a history, and ordinarily no opinion is given as to the cause for the success or failure of individual projects. Increasing the production of oil is exceedingly important at this time, and one method by which it may be done most readily is by providing additional energy for the movement of oil in many of the older fields. In many oil fields the predominant force that drives oil through the porus reservoir rocks to wells is the gas dissolved in or otherwise associated with the oil under pressure. As the pressure in the reservoir declines in consequence of the removal of fluid, gas comes out of solution in the form of minute bubbles; as the pressure is reduced further, the expansion of these bubbles forces part of the oil toward the areas of lowest pressure and into the producing wells. The physical properties of the oil and the gas governing their flow through reservoir rocks to wells differ, and much of the gas slips past the oil leaving large quantities of oil in the reservoir when the pressure has been exhausted. Often the natural productive life of fields is prolonged by reducing the pressure in oil wells below atmospheric with vacuum pumps; but the ad- ditional energy made available in this manner is limited to less than 1 atmos- phere of pressure, and even after the extended application of "vacuum" to a petroleum reservoir large quantities of oil are left unrecovered in the porous rocks and sands.

Nov 1, 1943

By Sean Gallagher

Study Design. A split-plot experimental design was used to evaluate the influence of posture, trunk angle, and rotational velocity on peak torque output and myoelectric activity during maximal trunk extension maneuvers. Objectives. To determine whether the kneeling posture alters extension torque capabilities in isometric and isokinetic exercises as compared with standing. Also, to ascertain whether recruitment of trunk muscles is modified by such a postural change. Summary of Background Data. Factors such as workplace geometry may force workers to adopt awkward or unusual postures in the performance of manual tasks. An understanding of the limitations placed on strength in unconventional working postures is crucial to the proper design of jobs. Methods. Twenty-one healthy male subjects (mean age = 36 years 7 SD) performed 12 trunk extension exertions in standing and kneeling postures. Isometric tests were performed at 22.5°. 45°, and 67.5° of trunk flexion. isokinetic tests were done at three velocities: 30°/sec, 60°/sec, and 90°/sec. Electromyographic data were collected from eight trunk muscles to assess muscle recruitment under each condition. A prior; orthogonal contrasts were specified for analysis of both torque and electromyographic data. Results. The kneeling posture was associated with a 15% decrease in peak torque output when contrasted with standing; however, no concomitant change in trunk muscle activity was evident. Trunk hyperflexion (isometric tests) and increasing rotational velocity (isokinetic tests) were associated with reduced torque in both postures. Trunk muscle activity was primarily affected by changes in trunk angle and velocity of contraction. Conclusions. A reduced extensor capability exists in the kneeling posture, despite equivalent trunk muscle activity. The similar activation patterns in both postures suggest that the strength deficit does not result from alterations in trunk muscle function. Rather, it may be the consequence of a reduced capability to rotate the pelvis in the kneeling posture, due to a disruption of the biornechanical linkage of the leg structures. [Key words: electromyography, isokinetic, isometric, low back pain, posture. strength1 Spine 1997;22:1864-1872

By Dorsey A. Lyon, Robert M. Keeney

This bulletin is one of a series dealing with the application of the electric furnace to the smelting of ores and the manufacture of alloys, and is published by the Bureau of Mines in the endeavor to increase efficiency in metallurgical processes. The bulletin presents, first, a critical discussion of the possibility of smelting copper ores in the electric furnace; second, the results of the experimental work of other investigators on the electric smelting of copper; third, the results of experiments by the authors on the electric smelting of native copper concentrates and sulphide copper ores; and, fourth, a comparison of the electric furnace with the blast furnace and reverberatory furnace for copper smelting. Before considering the electric smelting of copper ores the reader should understand that the electric furnace was not developed as a competitor of the combustion furnace, but for the purpose of doing high-temperature work that can not be done in the combustion furnace, and for the treatment of ores from deposits that are in regions where fuel is scarce and costly but hydroelectric power is comparatively cheap, as in Chile, and in certain parts of Canada, the United States, and Mexico. Furthermore, it is not the object of this report to try to prove that the electric furnace should replace the reverberatory or the blast furnace, as used at present in smelting copper ores, but to show that the electric furnace may be used with advantage in localities where conditions are not favorable to the use of the reverberatory or the blast furnace. For example, otherwise valuable ore deposits may be situated in a district so remote from, or inaccessible by, railway that the cost of get- ting coke for smelting, or of transporting the ore to a smelter, is pro- hibitive. If there is sufficient water power at hand, from which electric power can be developed at a reasonable cost, and this electric power is used for smelting the ore in an electric furnace, with subse- quent bessemerizing, if necessary, the concentrated product may be

Jan 1, 1915

By K. L. Rubow

"Diesel exhaust and mineral dust concentrations have been measured for aerosols generated in the laboratory and as found in five underground coal mines- 3 utiliting diesel-powered hallage equipment and two electric-powered equipment. Two source apportionment techniques have been applied to differentiate between the mineral dust and diesel exhaust aerosol concentrations. The first technique, using a microbrifke uniform deposit impactor CMOUDI) for size selective sampling, is based on modeling aerosol size and the premise that the diesel exhaust portion of .the aerosol is predom1nately submicrometer and the mineral dust portion is mostly greater that one micrometer in size. The second technique, Chemical Mass Balance CCMB) modeling, was used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results. ,The MOUDI size distribution data were modeled to obtain parameters describing the fine and course fractions of the sampled aerosol and to estimate the contributions to each mode from both mineral ·dust and diesel exhaust aerosol sources. The results showed the size distribution of the mixed aerosols exhibited two definite modes with the minimum between the modes occurring at 0.8 um. For the diesel equipped mines, this analysts yielded an average value for the fraction of the fine aerosol attributable to mineral dust of 1 pct. Less than 5 pct of the coal mine diesel aerosol was found in the coarse size fraction. CMB analysis confirms the original premise for using aerosol size to separate diesel exhaust and mineral dust aerosol during sampling."

Jan 1, 1988

By M. Terry Hoch, George J. Karabin, James M. Kramer

This paper introduces the fracture mechanics approach—a unique way to predict the stability of a coal mine panel. The technique uses analytic equations to calculate the stress, strain, and yield characteristics of coal support systems. It uses fracture mechanics to model almost every type of mine support structure. Another feature is a method that incorporates field-tested knowledge into the analytical analysis. For example, this technique can model the yield characteristics of a coal seam by combining empirical pillar strength equations into the analytic analysis. It may be possible to simulate multiple-seam mining by incorporating subsidence methods into the analysis. The method is simple and quick, which makes it attractive for stress analysis software. It should be more accessible to those in the mining industry who do not have expertise in rock mechanics or numerical modeling. Although the purpose of this research is for modeling coal mines, it should be adaptable to any mine in a tabular deposit.

Jan 1, 1999

To improve mining safety and efficiency by providing a practical way of detecting faults and channel sands that disturb coal seams. Approach A seismic system using a shallow blasthole has been developed and tested. How It Works A small shock is caused in a shallow hole, sending seismic waves through the ground. These waves are reflected from the top of the coal seam, acid are detected by a line of geophones on the earth's surface. Dampening of the seismic signals by channel sands and other discontinuities in the seam is detected and recorded. See Figure 1. The seismic shock wave can be produced by exploding small charges, dropping a weight, firing a gas gun, or actuating a vibrator. Depending on the soil cover, the shock is usually generated in shallow vertical holes about 10 feet deep. Hole depth depends on the soil mantle thickness because it is preferable that the seismic shock originate below that layer.

Jan 1, 1976

By S. McGinn, G. Schnakenberg, D. Petrie, A. Bugarski, M. Grenier

As part of the Diesel Emissions Evaluation Program (DEEP) consortium, Noranda Inc. has undertaken a field project to evaluate the overall performance of the latest diesel particulate filter technology (DPF) at its Brunswick Mine in Bathurst, New Brunswick. Performance of the filtration systems is evaluated with respect to their ability to reduce tailpipe emissions and concentrations of diesel particulate matter (DPM) and noxious gases in mine air, efficiency of filter regeneration process, maintenance requirements, reliability, and acceptance. Four different particulate filter systems deployed on heavy production vehicles are subjected to an 18-month field evaluation. Over the evaluation period the vehicles will have accumulated approximately 4000 operating hours in production. This paper presents the results of testing conducted mid way through the 18-month field trials. The 400- meter section of the mine drift at 525-5 sub level, hereinafter referred to as the "isolated zone" was isolated between intake and exhaust fan systems and sealed with bulkheads against leakage. The isolated zone was ventilated at the rate required per CSA Standards and issued by CANMET for the engines tested. Four vehicles, two load-haul-dumps (LHDs) and two trucks, retrofitted with particulate filter systems were tested along with a new identical model LHD and truck equipped with exhaust systems consisting of a catalytic converter (DOC) and muffler. The test vehicles were operated individually inside the isolated zone for approximately 4 hours over simulated production duty cycles. Measurements of ambient concentrations of particulate matter, tailpipe emissions, and engine parameters were performed for each of the tested vehicles. The DPM samples for carbon were collected at the most up- stream end of the isolated zone, at the vehicle next to the operator, and at the most downstream or exhaust end of the isolated zone. The DPM samples were analyzed for total (organic and elemental) carbon using NIOSH Analytical Method 5040. Ambient concentrations of particulate matter at the exhaust end of the zone were also measured using Scanning Mobility Particle Sizer (SMPS), and real time PAH monitor (PAS 2000). Efficiency of the filters was also evaluated on a basis of tailpipe measurements performed using raw exhaust instruments the NanoMet and the UGAS. In addition, relevant engine parameters were obtained using Detroit Diesel Diagnostic Link (DDDL) and from exhaust backpressure and temperature measurements. Results from the tests proved conclusively that diesel particulate filters can significantly reduce the concentrations of air- borne DPM, but not without careful monitoring of both ambient and tailpipe emissions and not without careful attention with respect to maintaining the integrity of the DPF systems.

By F. W. Woodman

N/A

Feb 1, 1943

By E. D. Regad, W. E. Wallace, V. Vallythan, V. Castranova, P. Hathaway, F. H. Y. Green, M. J. Keane

"Abstract—Inhaled particle contact with pulmonary surfactant in the hypophase lining pulmonary alveoli was modelled in vitro by exposing two respirable sized dusts, kaolin and silica quartz, to lecithin, a major component of pulmonary surfactant, emulsified in physiological saline. Lecithin adsorbs to the dusts upon incubation at 3TC and suppresses their cytotoxicity as measured by pulmonary macrophage and erythrocyte assays, suggesting that pulmonary surfactant provides a defence system against prompt cell membrane lysis by inhaled dusts. Subsequent pulmonary macrophage phagocytosis and lysosomal enzyme digestion of the coated dusts was modelled in vitro by incubation with phospholipase A2 for one hour. With increasing lipase activity, silica haemolytic potential was restored to native silica levels. Kaolin was retoxified to levels far in excess of native kaolin haemolytic potential. Elution, thin layer chromatography and phosphate assay of treated dusts indicate that most lecithin on silica is digested to lysolecithin and desorbed, silica retoxification being due to surface and adherent lysolecithin effects. Most lecithin on kaolin is not digested in the same time; that which is. results in adherent lysolecithin which is responsible for the kaolin retoxification. Digestion with phospholipases A2 and C together produces only weakly retoxified kaolin. Results suggest that surface adsorption properties which control the adherence of prophylactic surfactant distinguish the pathogenic potentials of quartz, kaolin and mixed dust.INTRODUCTIONERYTHROCYTE HAEMOLYSIS and pulmonary macrophage enzyme release assays show quantitatively comparable high cytotoxicities for both silica quartz and kaolin respirable sized dusts (BROWN, et al., 1980; DANIEL and LE BOUFFANT, 1980.) This contrasts with the strong potential for respirable quartz dust to induce pulmonary fibrosis and the much more limited potential of kaolin dust to do the same (MORGAN and SEATON, 1975).In an attempt to understand this anomalous situation, assays were performed on quartz and kaolin dusts incubated with dipalmitoyl lecithin emulsified in physiological saline, to simulate the initial contact of a respired dust with the pulmonary alveolar hypophase. The ability of kaolin dust to adsorb dipalmitoyl lecithin from physiological saline has been quantified (WALLACE, et al., 1975). Such lecithin treatment suppresses the cytotoxicity of both silica and kaolin to background levels (WALLACE, et a1.,1984).Surfactant coated detoxified dusts should then be phagocytised by pulmonary macrophages, incorporated into a macrophage secondary lysosome and exposed to hydrolytic lysosomal enzymes. Among these is phospholipase A2, which hydrolyses diacyl lecithin to lysolecithin. This was modelled by incubating lecithin treated dusts with phospholipase A2 in vitro to determine if the enzyme can digest the dust-adsorbed lecithin, and if the retoxification differs between the two dusts in a manner which might distinguish their pathogenicity."

Jan 1, 1988

By Tony Keller, Setsuo Maeda

Hand-Arm Vibration Syndrome (HAVS) was identified as early as 1918 in Bedford, Indiana in the U.S. Since then much research work has been done around the world in the areas of medical, epidemiological, engineering and legal aspects of HAVS. In Japan, much of the pioneering work in this field has been performed by Dr. Setsuo Maeda and his staff at the National Institute of Industrial Health (NIIH) in Kawasaki. Most recently, reports of work done by this group and by Dr. Ren Dong1 of NIOSH in the U.S., as well as many other suppliers and Japanese practitioners were presented at the 13th Japan Group Meeting on Human Response to Vibration held in Osaka2 during August 3-5, 2005. [ ]

Jan 6, 2006

By Stephen D. Cramer

The Bureau of Mines conducted a series of in situ linear polarization measurements in high-temperature, high-pressure hypersaline geothermal brines at the Bureau of Mines Geothermal Test Facility in the Imperial Valley of California. The measurements represented an evaluation of the linear polarization technique for obtaining instantaneous corrosion rates of materials of construction in flowing hypersaline hydrothermal fluids that rapidly form scales on exposed surfaces. A special method was devised for use with the linear polarization technique that resulted in obtaining corrosion rates for 1020 carbon steel, 316 and 430 stainless steel, titanium, various nickel-based alloys, and aluminum 6061 under strong scale-forming conditions. The measurements also provided information on scale-deposition rates in various geothermal environments. Exploratory in situ potentiostatic polarization measurements were made in the flowing brines to qualitatively determine scale-deposition effects on the electrochemical measurements.

Jan 1, 1978

By D. Harrington

In recent years over 100,000 persons have been killed annually in the United. States by accidents; about one-fifth of these have been workers in some of our industries; about one-third have been killed by motor vehicles; about another third have mot death in home accidents, chiefly falls, burns, scalds, explosions, poisons, asphyxiations, suffocations, cuts, scratches, and so forth; and the rest have been killed in public accidents, excluding those caused by vehicles but including accidents on railroads or electric cars, drowning, and deaths by firearms and. other means. Definite statistics on nonfatal accidents are not readily available, but at least 10,000,000 fairly serious accidents probably occur in the United States annually. The latest industrial-accident statistics are obtainable from 1935 National Safety Council publications, in which annual industrial fatalities are divided about as follows (in round numbers): Agriculture, 4,500; trade and service, 4,500; construction, 3,100; transportation and public utilities, 2,900; manufacturing, 2,600; mining, quarrying, petroleum, etc., 1,900.

Jan 1, 1938

By Benjamin W. Haynes

Materials from phosphate rock mining and processing were analyzed for fluorine and uranium content as part of the Bureau of Mines program to more effectively recover resources from mining and mineral processing reject materials. The analysis of both feed and waste materials generated in the beneficiation and acidulation of phosphate rock was performed to obtain information on the disposition and concentration of these elements in phosphate rock processing streams. Fluorine was determined by a distillation-titration method and by ion chromatography. Uranium was determined by the dibenzoylmethane (DBM) method, the reliability being confirmed by roundrobin analysis of samples within Bureau of Mines research centers. National Bureau of Standards (NBS) Standard Reference Material (SRM) 120b-Phosphate Rock was also analyzed for fluorine and uranium to verify procedures and results. Fluorine values ranged from 0.3 wt-pct in gypsum filter cake to 3.7 wt-pct in phosphate rock concentrate. Uranium ranged from less than 5 µg/g in gypsum filter cake to 200 µg/g in a dried clay slime.

Jan 1, 1981

By Joseph A. Sutton

The prospect of utilizing bacteria in mining and metallurgical processes introduces a new and challenging area of investigation. Elements of bacteriology and metallurgy are discussed in connection with possible areas where biological science might be applied in extractive metallurgy. Bacteria may prove important in the selective separation of metals from ores and metallurgical solutions, the production of sulfur from gypsum or pyrites, and the production of sulfuric acid from elemental sulfur. A series of reports concerning the experimental applications of bacteria on minerals and metallic ores will follow this paper. For several years the Bureau of Mines has been investigating the action of bacteria in the oxidation of sulfide minerals and their potential uses in metallurgical processes. Primary attention has been given to the possible utilization of certain strains of autotrophic bacteria that live in industrial leaching solutions or fractures of mineral outcrops. The purpose of this paper is to acquaint the mining and metallurgical engineer with micro-organisms and some of their possible applications in the field of extractive metallurgy.

Jan 1, 1961

By J. N. Van Sant

Lignite mining in North Dakota was begun about 1884 to supply the domestic needs of settlers. Annual production has grown rather slowly but steadily, exceeding 3 million tons in 1950. The western part of the State has lignite reserves, amounting to 351 billion tons, underlying an area of 28,000 square miles. Contour strip mining has almost completely replaced underground mining as the method of production. Lignite is often found under rather shallow and easily removed overburden, and this is the primary reason for the change in mining practice. Current mining operations are conducted where the overburden is 30 to 70 feet thick. Contour strip mining results in high production rates, at present 27 to 56 tons per man-day. These high production rates result in relatively low production costs.

Jan 1, 1959