Search Documents

By John C. Franklin

A radon survey was made at five different locations in the Twilight mine near Uravan, Colo., to determine chances in radon concentrations in an inactive mine. Data were taken with a continuous monitor set for 1-minute count periods and readings were taken 24 hours a day for 9 days. The 12 readings per station each hour accurately showed how t w radon concentration varied during the day. From the data collected from the intake portal to station 4, the average radon emanation rate was estimated at 18 picocuries per second per square foot (pCi/sec/ft3). A daily cycle in radon concentration was detected that apparently was related to barometric pressure change.

Jan 1, 1976

By Jacqueline A. McClaskey

The U.S. Bureau of Mines (USBM) Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The USBM's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the USBM survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By Jürgen F. Brune, R. Karl Zipf, Kenneth L. Cashdollar

This paper outlines the legal standards and methods for protecting underground coal mines in the United States from explosions of methane gas and coal dust. It will discuss inspection and monitoring of mine atmospheres, dilution of methane through ventilation, methane drainage prior to, during and post-mining, as well as explosion prevention through rock dusting and sealing of mined-out areas. Recent research findings of the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory on the magnitude of pressures obtained during methane explosions from modeling and full-scale explosion tests at the NIOSH Lake Lynn Experimental Mine will be presented. This work is currently being applied to modeling the structural response of explosion-proof mine seals to pressures from gas explosions. Also, new research will be presented on the inertization of float coal dust in mines through the addition of inert stone dust and on the application of the Coal Dust Explosibility Meter (CDEM), a handheld device developed by NIOSH to directly measure the explosibility of a coal dust - limestone dust mixture based on optical reflectivity.

By A. B. Coates

During the last three years the use of ethylene glycol dinitrate4 (E.G.D.) as at low-freeze (L.F.) agent in place of nitropolyglycerin has become common in the manufacture of explosives of the dynamite type. The usual proportion of D. G. D. in the explosive "oil" is 25 per cent; the remainder, 75 per cant, is regular nitroglycerin. These proportions were probably selected as a continuation of the practice of 25 per cent nitropolyglycerin and 75 per cent regular nitroglycerin.

Jan 1, 1929

By J. A. McAllister

In the course of a study of domestic Manganese resources, 2-ton representative samples of ore were taken by Bureau of Mines' engineers from the Payday claim, Weber County, and the Newcomb-claims, Rich County, Utah. The Payday No. 1 deposit is situated 13 miles northeast of Huntsville, Weber County, Utah. The manganese ore is a. replacement deposit in limestone and consists of manganese oxides imbedded 'in clay and also as the cementing agent consolidating small pebbles and pieces of quartz and limestone.

Jan 1, 1949

By J. A. McAllister, H. G. Iverson, K. C. Dean

"INTRODUCTION During the course of the investigation of the occurrence of manganese deposits in the western United States, laboratory studies of concentration were conducted at the Salt Lake City station on a sample of ore from the Lake Valley mines of the Newalpitt Fluorspar Corp. of Deming, N. Mex. The ore was reported to be representative of the type that would be mined for mill feed. The sample tested was found to be amenable to beneficiation by ore-dressing methods for the production of products that, when sintered, assayed over 44 percent Mn.At the beginning of the investigation of manganese-ore beneficiation in December 1940, the only product marketable to Metals Reserve Company was ferrograde manganese grade B, the requirements for which follow: Mn, min., 48 percent; Fe, max., 7 percent; Si02, max., 10 percent; P, max., 0.18 percent; Al203, max., 6 percent; Zn, max., 1 percent, Al2O3,Later the specifications were modified gradually. As of May 15, 1943, manganese products were acceptable if they contained over 35 percent manganese and less than 3 percent zinc and 1 percent phosphorus. Prices were based upon material containing 48 percent manganese, 6.0 percent iron, and 11 percent silica plus alumina. Premiums were paid for manganese content in excess of 48 percent and iron content below 6 percent, penalties being imposed upon products containing less than 43 percent -manganese, or more than 6 percent iron, or more than 11 percent silica plus alumina. The specifications for commercial manganese further required that maximum particle size be 12 inches and that, 75 percent of the product be coarser than 20-mesh. Therefore, fine material such as table and flotation concentrates had to be nodulized or sintered. In addition, oarbcnate manganese ores were not acceptable unless calcined."

Feb 1, 1948

By Knox Van Dyke, Vincent Castranova, Lixin Wu, Mark J. Reasor, James M. Antonini

"One of the proposed mechanisms involved in the pathogenesis of silicosis is that inhaled silica dust activates a ""respiratory burst"" in pulmonary phagocytes, such as macrophages and neutrophils. This increase in oxidative metabolism results in enhanced generation of reactive oxygen species which if produced in excess, would overwhelm natural defense mechanisms and cause damage to the lung parenchyma. This damage would then result in scarring, fibrosis, and decreased gas exchange.Weiss and LoBuglio' have listed several oxygen species produced by phagocytes which may be involved in cellular injury. These oxidants include superoxide anion, hydrogen, peroxide, hydroxyl radical, and hypochlorous acid. Superoxide anion (0;) is generated from molecular oxygen by the plasma membrane bound enzyme NADPH oxidase according to the following reaction:Once generated, superoxide anion can form hydrogen peroxide:In the presence of myeloperoxidase and halide, hydrogen peroxide can form hypochlorous acid:Superoxide and hydrogen peroxide can also form highly reactive hydroxyl radicals. Hydroxyl radicals can be generated slowly by the Haber-Weiss reaction:In addition. hydroxyl radical production can be catalyzed via the Fenton reaction:Hydroxyl radicals can also be generated from the reaction of superoxide and hypochlorous acid as follows:Recent investigations suggest that, in addition to the reactive oxygen species discussed above, nitric oxide may be a potential mediator of silica-induced toxicity.2-4 Nitric oxide (NO') can be generated by the cytosolic enzyme nitric oxide synthase according to the following reaction:NO synthase exists in two forms. i.e.. a constitutive. Ca2+-calmodulin-dependent form and an inducible. Ca2+-calmodulin-independent form. In pulmonary phagocytes. the activity of the constitutive form of NO synthase is low. However. NO synthase can be induced in macrophages and neutrophils by a variety of stimulants such as lipopolysaccharide. interferon y. chemotactic peptide, platelet activating factor, or leukotriene B4.3.5Once generated. nitric oxide can combine with superoxide anion to form peroxynitrite as follows:Peroxynitrite is a potent oxidizing agent. In addition, peroxynitrite can form peroxynitrous acid. which in turn can produce hydroxyl radical and nitrogen dioxide (all of which exhibit strong oxidizing potential) by the following reactions:Oxygen metabolites have been shown to cause lung damage in vivo.6 Such damage includes edema. leakiness of the alveolar endothelial/epithelial barriers, and airway constriction.7 Superoxide and hydrogen peroxide have been associated with membrane damage and cell lysis.8 These oxidants have also been associated with alteration of cytoskeletal structures at cell-cell junctions and elevation of transepithelial conductance in cultured monolayers.9 Macrophages or neutrophils can be stimulated by bacteria or phorbol myristate acetate to produce sufficient oxidant levels to lyse lymphoma cells.10 This cell killing is inhibited by catalase but is unaffected by superoxide dismutase. hydroxyl radical scavengers. or azide. i.e., an inhibitor of peroxidase. This implicates hydrogen peroxide as the active oxidant. Similarly. Weiss et al.11 have reported that hydrogen peroxide is critical in the death of cultured endothelial cells due to neutrophil activation. In addition. hydroxyl radicals generated by monocytes have been associated with cell injury.12 Lastly. peroxynitrite has been shown to oxidize sulfhydryl groups and to inactivate proteinase inhibitor making the lung more susceptible to damage caused by phagocytotic enzymes.' Therefore. a strong case can be made that activated pulmonary macrophages and neutrophils are capable of causing oxidant injury. This chapter presents in vitro and in vivo data indicating that silica is associated with the production of reactive oxygen species from these pulmonary phagocytes."

Jan 1, 1998

By M. Clair Smith

This report is one of a series describing exploration, development, mining, and processing of mineral deposits in the United States. The reports are prepared and published by the Bureau of Mines in cooperation with various mining companies The purpose of the reports is to promote development and conservation of our natural reserves by disseminating technological information on mining and milling procedures and related practices at operating mines. Simplot Silica Products, Inc., mines and processes a friable silica sandstone. The finished products are sold for use in glass manufacture, foundries, chemicals, and special applications.

Jan 1, 1959

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By W. E. Wallace, P. S. Raghootama, M. S. Seehra, C. A. Hill, M. J. Keane, P. Mike

"Dipalmitoyl glycerophosphorylcholine (lecithin) dispersed in physiologic saline, a model of the primary component of pulmonary surfactant, is adsorbed by respirable quartz and aluminosilicate dusts. Dust cytotoxicity as measured by erythrocyte hemolysis and pulmonary macrophage enzyme release is suppressed by this adsorption. The degree of suppression of hemolytic potential versus specific adsorption of lecithin from dispersion in saline by respirable quartz, kaolin, and alumina dusts are compared with dusts' BET specific surface areas to interpret the prophylactic effect cf lecithin adsorption. Dust hemolytic potential versus media pH are presented. Fourier transform infrared spectroscopy and photoacoustic spectroscopy of lecithin on quartz and of lecithin on kaolin are presented and reviewed with results of studies of the time course of removal of lecithin adsorbed on mineral surfaces by digestion by phospholipase enzyme. Results are discussed in terms of a model of prompt neutralization of respired mineral dusts by pulmonary surfactant, and a gradual re-toxification by digestive processes acting on the adsorbed prophylactic surfactant coating following phagocytosis.Introduction Quarts dust of respirable size is well known to cause fibrotic lung disease, but numerous questions persist in the understanding of the initiation and' progression of this disease. Our approach concentrates on physical and chemical aspects of mineral dusts early-on in their interactions with living organisms, and we have chosen simplified models to investigate that interaction. In the alveolar spaces of the lung, tissue is coated with a surface-active material (pulmonary surfactant), which, sagas other functions, mechanically stabilises the lung from collapse by reducing the surface tension of water in the alveolar sacs.(1) This surfactant is also the material that is first contacted by a mineral particle that is transported to an alveolus and is impacted there. This surfactant material has been studied extensively. The primary components are known to be proteins (about 11% in dog lavage fluid). and phospholipids (about 88%).(2) Fhosphatidyl cholines constitute roughly 80% of the phospholipid fraction; about 70% of the phosphatidyl choline fraction is dipalaitoyl lecithin (DPL).(2) Respirable aluminosilicate particles are capable of adsorbing dipalmitoyl lecithin from dispersion in physiologic saline, a model for a possible initial event occuring upon deposition of a particle in a pulmonary alveolus.(3)"

Jan 1, 1988

Lower workers' dust exposures during bag stacking while ergonomically improving the bag stacking process. Approach Install a new pallet loading dust control system which uses a push-pull ventilation technique along with a hydraulic lift table to control the pallet loading height throughout the entire loading cycle. How It Works A low-volume, high-velocity blower system operating at approximately at 120 cfm blows a stream of air over the top layer of bags on the pallet. The blower system is composed of two 3-inch air jets (approximately 1,200-ft/min velocity) directed toward an exhaust system on the opposite side of the pallet. As these air jets travel across the pallet, they en-train dust generated during bag stacking. The dust laden air is then captured by the exhaust ventilation system which draws approximately 2,500 cfm through an exhaust hood on the opposite side of the pallet.

Jan 1, 1989

By L. C. George

Addition of an acid waste to an alkaline cyanide waste was investigated for five different combinations of electroplating wastes. At the optimum final pH values of the mixtures, metals and cyanides were almost quantita¬tively precipitated. No evolution of hydrogen cyanide was detected by a few additional processing steps, significant amounts of variable metals were recovered for recycling the waste-plus-Waste step is attractive because no reagents are required, metals arc concentrated, and a relatively harmless effluent that meets most water quality Standards for cyanide content is produced.

Jan 1, 1970

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they arc required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by G. E . Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By Paul M. Tyler

A great variety of substance that differ widely in chemical, mineralogical, and physical properties are loosely linked under the generic term "clay", but for the average man all that matters is whether a given material can be sold or used profitably. So-called "clays" range in texture from true clays and allied minerals that are typically "fat" or sticky to fine sand. Sand and other strictly silicious materials, such as tripoli and diatomite, are not clays in any sense; but many commercial clays are strictly loams, for they are intermediate in texture and always contain a mixture of minerals, though the term "loam" has little commercial usage except in foundry work. Even pure kaolinite, ordinarily considered the typical "clay substance", recently was found to exist as three distinct minerals; and each of these, in turn, exhibits variations in particle size and other physical attributes. Probing with the X-ray and employing other modern tools and techniques, scientists are tracing the patterns of molecules and finding chemical and physical phenomena that seem to disclose the causes for the markedly different behavior of the various aluminum silicates with varying proportions of combined and adsorbed water that are the essential ingredients of commercial clays; but rule-of-thumb definitions and enforced reliance upon empirical tests of actual samples still hold sway. In addition to the hydrated simple silicates of aluminum, almost all clays contain quartz, feldspar, and mica with varying amounts of organic matter and, in addition, other impurities - such as iron, manganese, and titanium oxides - that may discolor them sufficiently to render them unfit for certain important uses. The white clays are generally the purest, but no two clays are really alike, and great care must be exercised to maintain a reasonable uniformity in successive shipments even from the same deposit.

Jan 1, 1938

By F. E. Cash

The Holmes Safety Association , organized and named in honor of the late Dr. Joseph A. Holmes , first director of the United States Bureau of Mines , has for its object the prevention cf accidents , the improvement of health conditions at work, in the home , and in public places , and the promotion of the general welfare of its members . As a means of preventing accidents and advancing health and safety , the Holmes Safety Association disseminates information , gives instructions on subjects related to safety , and promotes first -aid and other forms of protective and accident - prevention training . This organization is intended to work and cooperate in the closest possible way with existing mine or plant safety organizations in conducting educational , social , and recreational activities for the promotion of health , safety , and efficiency .

Jan 1, 1929

By A. L. Murray, P. A. Surgeon

The Spring Canyon Mine Rescue Association is a cooperative association supported jointly by five coal-mining companies located in Spring Canyon, Utah. The properties of mining companies the Carbon Fuel Co, Rains , Utah, the Liberty Coal Co. , Latuda, Utah, the Standard Coal Co. , Standardville , Utan, the Spring Canyon Coal Co. , Storrs , Utah, and the Peerless Coal Co. , Peerless , Utah about a mile apart and normally employ a total of 915 men , 733 underground 182 on the surface . and The Association was organized on July 5, 1921 , and Rudolph Clark, fomerly first - aid miner on U. S. Bureau of Mines Rescue Car 11 , was placed in charge. as manager . A board of directors made up of a representative from each of the cooperating companies (usually the mine superintendent ) is the governing body of the Association and the expenses are prorated on a basis of the production of each of the five mines . The Association maintains eight sets of Gibbs rescue apparatus and a motor truck fitted up as a combined rescue truck and ambulance . Additional apparatus are to be purchased . Standardville is the central camp in the canyon and has been made the headquarters of the Association . The apparatus are now kept and the truck housed in a small station, but plans have been prepared for a large station which will be built this summer . This new station will have a large apparatus room , a test chamber, a suitable room. for training, and a garage on the first floor, while above will be the living quarters of the manager . There is a good road through the canyon and the other camps are all within two and one -half miles of Standardville .

May 1, 1922

By J. J. Forbes

The Coal Mine Inspection Branch of the Health and Safety Division, Bureau of Mines, was established to carry out the provisions in Public Law 49, 77th Congress, H. R. 2082, approved May 7, 1941. The series of major disasters that beset the coal-mining industry in 1940 aroused public interest in mine-safety measures, and the act 18 the direct result of this rekindled interest. Under the provisions of the act, the Secretary of the Interior, acting through the Federal Bureau of Mines, is authorized and empowered to make, or cause to be made, annual or necessary inspections and investigations in coal mines, the products of which regularly enter commerce or the operations of which substantially affect commerce. The principal functions of the Federal coal-mine inspectors are to determine the causes of accidents and occupational diseases in coal mines and then endeavor to eliminate or ameliorate them (1) by revealing, through personal conferences with mine personnel, correspondence, and published reports, the unhealthful and unsafe conditions and practices existing in the mines and (2) by recommending practical means for correcting the conditions observed. The act does not provide any enforcement powers, and therefore compliance with the inspectors' recommendations is not mandatory; it does give Federal coal-mine inspectors the right to enter coal mines for inspection purposes.

Jan 1, 1951

As part of the Bureau of Mines subactivity in secondary resource recovery and to expand the Nation's mineral base, the Tuscaloosa Research Center made characterization and preliminary beneficiation studies of the waste residues from various coal-conversion processes: from pilot plant tests of the Synthane process for coal gasification, the Synthoil process for coal liquefaction, and the solvent-refined coal (SRC) process for sulfur removal from coal. Those coal conversion processes selected for this study were based on the availability of pilot plant samples. Physical, chemical, and mineralogical examinations of the wastes made to determine the mineral content prior to physical beneficiation tests indicated that in addition to significant quantities of carbon, some trace elements offer potential for concentration.

Jan 1, 1980

"In sum, significant benefits to mine worker health have resulted and should continue to result from the synergistic scientific, engineering, and medical research in respirable dust. As always, an important objective is the rapid dissemination of the results of this research to industry. Video tapes and the Technology News series published by the United States Bureau of Mines (USBM) have been a very effective means of technology transfer. Individual no-cost subscriptions to the Technological News series are available from the Bureau of Mines, Branch of Technology Transfer, 2401 E St., N.W. Washington, DC, 20241.Two respirable dust conferences have been jointly sponsored by the Center, USBM, NIOSH, and MSHA. The proceedings from these conferences are titled:1. Coal Mine Dust Conference held in Morgantown, West Virginia on October 8-10, 1984 and2. Respirable Dust in the Mineral Industries: Health Effects, Characterization and Control held in University Park, Pa. on October 14-16, 1986.Copies of the proceedings from the first conference are available from the National Technical Information Service (NTIS):National Technical Information Service5285 Port Royal RoadSpringfield, VA 22161NTIS # PB86-169380Telephone Number: (703)487-4650Copies of the second conference proceedings, ISBN: 0-936712-76-7 (publication #3010), are available from ACGIH by writing toWilliam D. KelleyExecutive Director, A.C.G.I.H.6500 Glenway Avenue, Building D-FCincinnati, Ohio 45211Telephone Number: (513)661-7881During the period 1984-1987 more than sixty-four (64) papers and publications have been produced by the Center researchers. These publications have appeared in scientific journals and have been presented at national and international symposiums and meetings. A list of these papers, organized by topical headings, has been included in this publication.The generic center maintains a reference center that serves as a clearinghouse for technical information for the generic area and supplies reports on generic center accomplishments."

Nov 1, 1988

By V. R. Spironello

The Bureau of Mines is conducting studies of the slags related to ferrous technology to evaluate acceptable substitutes for the auxiliary flux, mineral fluorspar, in foundry operations. This work is directed toward the Bureau's goal of minimizing the Nation's dependence on scarce and critical minerals Comparative basic practice cupola (18-inch-ID) trials were made to evaluate a waste material called "used potlining," which contains significant levels of fluorine, sodium, and aluminum in various compounds. Used potlining is recovered from alumina reduction cells after its useful life, and was supplied by the Aluminum Co. of America (Alcoa) to the Bureau for evaluation. The material in the lump and pelletized form (with limestone) provided extremely fluid slags based on visual observation during cupola operation. No adverse effects were found on cupola performance, metal and slag chemistry, the environment, or mechanical properties of the castings produced. Fluorine recovery in the slag was equal to, or higher than, that of fluorspar; fluorine losses to the scrubber water and solids were lower. The acidity of the scrubber Hater was somewhat neutralized. No difference was observed in furnace-refractory attack, as determined by the level of magnesia in the slag and visual inspection. The recovery of sodium in the slag, presumably as the oxide, significantly increased slag fluidity, suggesting that less than equivalent fluorine may be required. There was no contamination of the gray iron by the aluminum from the used potlining. Used potlining was completely satisfactory as a substitute for fluorspar in cupola ironmelting.

Jan 1, 1981