Search Documents

By A. B. Hooker

All state mining laws require that flame safety lamps be used in gassy mines; the laws of some States require that safety lamps be kept for emergencies at every coal mine, whether gassy or nongassy. The use of the flame safety lamp has been widespread because it is the only defice readily available for detecting both the presence of methane and deficiency of oxygen. This paper reports the results of an investigation by the Electrical Section, in cooperation with the Gas Section, of the Pittsburgh Experiment station relative to the behavior of permissible flame Safety lamps in mine atmospheres deficient in oxygen and the effects of methan5/ on the detection of oxygen deficiency.

Jan 1, 1937

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Colombia has been prepared from the best available information in Washington, but is released subject to correction and amplification; if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State. SYNOPSIS OF LAW Minerals in Colombia belong to the owner of the soil unless otherwise provided in the law. The following lands and deposits, however, are described as fiscal property of the State: Class 1. The public lands, mines, and salines which belong to the individual States (now Departments) prier to the adoption of the present constitution (1886).

Jan 1, 1929

By P. Comba

The U.S. Bureau of Mines investigated a hydrochloric (HC1)-calcium fluoride (CaF2) leaching procedure to treat domestic manganese (Mn)-bearing silicate resources. The proposed process is an alternative to high-temperature and energy-intensive extractive techniques. Single-stage leaching with a stoichiometric amount of HCl and a F-Mn mole ratio of 0.2 extracted 96 pct of the Mn when the leach conditions were 50° C, 3 h, and 35 pct solids. Ninety-eight percent of the Mn was extracted during countercurrent leaching at similar conditions. A process flowsheet was developed that incorporated HC1-Cab leaching, excess leach acid utilization, fluoride (F) recycle, and Mn recovery. When the domestic manganese silicate ore was processed, 98 pct of the Mn was extracted, 99 pct of the Cab was reclaimed, and a leach residue was produced that passed the Environmental Protection Agency (EPA) Extraction Procedure (EP) Test for nonhazardous waste.

Jan 1, 2010

By Peter N. Gabby

A mineral survey of 8,300 acres of the 24,980-acre Burnt Creek Wilderness Study Area (ID 45-12), was conducted by the U.S. Bureau of Mines in 1985 at the request of the Bureau of Land Management. The study area is located in Custer County, ID, 90 miles northwest of Idaho Falls. No mines, claims, or prospects are in the study area. The northern half of the study area and adjacent lands to the north, northeast, and east are or were recently under oil and gas lease, Basalt and latite-andesite of the Challis Volcanics predominate in the study area. Several hundred feet east of the study area is a quarry in talus of Mississippian-age limestone that was used for sized 100-pound rock fill in the Old Dry Creek Reservoir dam. Two samples, one taken at the quarry and the other at a limestone outcrop on East Fork Burnt Creek, have CaC03 content in the range of 90 to 95 percent, and is suitable as the limestone component of Portland cement, However, limestone outside the study area could supply foreseeable demand. Lead- silver mineralization has been observed in Paleozoic carbonate rocks elsewhere in the Lost River Range, but these rocks do not occur in the study area.

Jan 1, 1986

By Forrest T. Moyer

OVERALL data for 1963 on injury experience and the levels of employment, worktime, and operating activity of the mineral industries are shown in the statistical tables of this chapter. The general groupings of the industries are presented in greater detail in Volumes I and II of the Minerals Yearbook. A corresponding chapter in Volume I contains additional breakdowns of the data on metal, nonmetal, sand and gravel, slag, and stone mines and quarries together with separate information on the related processing mills and plants including primary nonferrous smelters. The more specific information on the anthracite and bituminous-coal, petroleum and natural gas, peat, and natural asphalt industries is given in the similar chapter of Volume II. Injury and employment data were collected from coal producers on the mandatory basis required by the Federal Coal Mine Safety Act (30 U.S.C., sec. 455). Producers of all other minerals (fuel and nonfuel) voluntarily reported the requested injury and employment data. The figures for 1963 are preliminary except for anthracite, coke, petroleum and natural gas, native asphalt, and slag which are final. Data for earlier years are final. The figures represent full coverage for all industries except the oil and gas industries for which coverage is not complete, particularly with respect to small companies.

Jan 1, 1964

By Alla D. Mah

No experimental heat-of-formation value has been reported in the literature for cerium sesquioxide. The heat of formation of bismuth sesquioxide has not been determined in recent years, and the older value was subject to large uncertainty. Accordingly, the heats of combustion of cerium sesquioxide and bismuth metal were measured by the Federal Bureau of Mines. The heats of formation were: ?H°298.15 = -427.01 ± 0.70 kcal. /mole for cerium sesquioxide and ?H°298.15 = -137.16 ± 0.30 kcal./mole for bismuth sesquioxide. The free energy of formation was estimated for cerium sesquioxide and accurately calculated for bismuth sesquioxide. The data were compared with values in the literature.

Jan 1, 1961

By J. R. Thoenen

During the year 1927 the Bureau of Mines, at the request of a number of quarry operators, undertook to make a study of quarry operating costs in order to determine average costs for certain operating conditions and to suggest a model cost accounting system for quarry operations. A detailed questionnaire was prepared and mailed by the bureau to all quarries on its records as employing ten or more men in 1926.

Jan 1, 1929

By J. A. Cavallaro

The heats of formation of anhydrous barium carbonate (witherite), strontium carbonate (strontianite), and lead carbonate (cerussite) were determined by solution calorimetry. The solution mediums were hydrochloric acid for barium and strontium carbonates and perchloric acid for lead carbonate. The heats of formation at 298.15° K are as follows: BaCO3 -297.5 ± 0.8 kcal/mole; SrCO3 -294.6 ± 0.5 kcal/mole; and PbCO3 -168.0 ± 0.3 kcal/mole.

Jan 1, 1966

By C. J. Johnson, C. J. Bise

"IntroductionCoal extraction by continuous miners (CM) is currently the most common underground method in the US industry and accounts for slightly more than two-thirds of the nation· s deep mining production (National Coal Association, 1987). Even if longwall mining should become more commonplace, it can proceed only af1er ventilation and access entries have been driven by CMs. Since an area of concern continues to be the effects of the dust generated on the health of mineworkers, this paper discusses the relationship between the elemental composition of mining-generated airborne dust sampled from the immediate ventilation return of a CM and laboratory-generated dust derived from channel samples taken from the mines.There are several potential contributions of this type of study to the coal mining industry. First after more fundamental knowledge of the causes of Coal Worker's Pneumoconiosis (CWP) is learned, the laboratory-generated respirable dust could be used to identify a potentially hazardous coal seam. Also, this study could possibly aid in understanding the fundamental causes of CWP by producing mining-simulated samples of coal dust that could be used in epidemiological studies.Further, assuming that there is no difference in the elemental composition of a drill-core sample and a channel sample from the same location a mining company could predict anew mine's respirable dust elemental composition In the immediate ventilation return by using exploratory drill core samples of the roof ,coal, and floor rock to prepare the laboratory dust. Ventilation engineers could then use engineering design and control measures during premine planning to reduce the incidence and severity of CWP by better ventilating the potentially hazardous coal seam. If this proper planning prevented any future changes to the ventilation equipment and mine design, much time and money could be saved.Scope of workTo investigate the variability of the chemical characteristics of respirable dust, airborne dust samples from eight underground coal mines located in the eastern and mid western United States were collected with eight-stage Sierra Model 298 Marple cascade impactors, as well as 25 channel samples of mined material. Each channel sample was removed from the middle of the coal face before mining occurred. Sampling of the mining-generated dust was conducted by Lee ( 1986) by sampling the entire working sections, primarily for characterization purposes, to obtain information on the locational variability of dust characteristics. Research performed for this study used the elemental analyses of the mining-generated dusts he sampled in the immediate ventilation returns of CMs."

Jan 1, 1989

By P. L. Sibrell

Electrorefining of Ti in nonaqueous solvents has been studied by the U.S. Bureau of mines as a method for recycling impure scrap Ti. Electrochemical behavior of Ti species was investigated using cyclic voltammetry. Research results showed that Ti metal can be dissolved in polar solvents such as dimethylformamide or dimethyl sulfoxide. However, deposition of Ti from these solvents was not successful. Several solvent systems were investigated for electrodeposition of Ti but no deposits were obtained. Reduction of Ti4+ complexes to Ti3+ proved to be straightforward, but reduction to lower oxidation states could not be confirmed. In dimethylformamide solutions, cyclic voltammetry results demonstrated the reduction of Ti to an oxidation state of less than three, but no Ti metal was identified. In dimethyl sulfoxide solutions containing LiCl, it was possible to deposit Li metal. After adding Ti salts to the solution, electrolysis quickly passivated the electrode. Deposition of Ti was also investigated in solutions of dimethoxyethane and propylene carbonate but, again, no reduction of Ti to oxidation states of less than three occurred. Therefore, the prospects for a nonaqueous electrorefining system for Ti metal do not appear promising.

Jan 1, 2010

By McHenry Mosier

The diamond-drill method was tried at the site selected for driving a 5- by 6 -foot air shaft at the east end of the Bellefonte mine . This method of sinking consisted , first , of drilling a 5-3/4 -inch-diameter cut hole from the surface , then drilling parallel 1.5 - inch ( EX ) holes around it at appropriate distances for a balanced blasting round . The cut hole was not charged with explosive but served as a relief chamber for the incipient expansion of the ground broken by. blasting the surrounding 1.5 - inch holes . The length of each hole was 236 feet , which was the finished depth of the shaft . The nature of the work in the air shaft was largely experimental , and many difficulties arising from the lack of special equipment and proper technique for precise alinement of the drill holes caused expensive delays before they could be overcome . Drilling the 5-3 /4 - inch hole , which was impeded by frequent core blocks in the core barrel , required 10 shifts . average advance per shift for an EX hole was about 150 feet . The The holes were charged and fired from the surface . The length of the section blasted in one cycle was 10 feet . Blasting progressed from the bottom of the shaft upward . The broken stone dropped into a chute , from which it was drawn into cars on the haulage level . The Bellefonte mine is an underground limestone mine.3/ The primary objective in undertaking the research on shaft sinking by diamond drilling was to perfect a method for driving connections between levels of the mine .

Oct 1, 1948

By P. S. Lewis

Shortage of natural gas is reviving interest in low-Btu fuel gas made by gasifying coal in fixed-bed producers. The Bureau of Mines gasified strongly caking Pittsburgh bed coal over test periods lasting four days in an experimental gas producer located at Morgantown, W. Va, Mechanical stirring throughout the fuel bed was effective for keeping the fuel moving and this stirring made the operation successful; hence, the gas producer was named the stirred-bed producer. Nuclear density gages were applied as control instruments to indicate coal flow and fuel level, and to record the frequency and location of void spaces in the bed, The gas, of nominal 140 to 165 Btu/scf calorific value, could be burned in a boiler for generating steam.

Jan 1, 1972

By G. M. Kintz, E. H. Denny

Although some engineering colleges recognize the importance of instructing young engineers in industrial safety , the different institutions handle this instruction in various ways . It is believed that a recent industrial safety course , conducted at the Colorado School of Mines through the cooperation of this school and the Bureau of Mines , U. S. Department of Commerce , presents some unusual features that are of interest to other schools and to the mining public .

Sep 1, 1930

By Robert S. Sanford

"INTRODUCTION AND SUMMARYThis paper is one of a series recently undertaken by the Mining Branch, Bureau of Mines, College Park, Md., to describe current practice in hauling ore and waste by truck at various mines.Heavy-duty ore trucks are replacing railroads at many large open-cut mines and even at a few underground mines. Recently a few mines have been equipped with trucks for transporting ore to a central point, from which conveyor belts move the ore out of the mine. This paper deals only with truck haulage methods and costs.The requirements for efficient low-cost truck haulage are good trucks designed for heavy loads, adequate truck maintenance, smooth roads, and well-trained truck drivers.A correct balance must be maintained between the primary crusher capacity, the number of shovels loading ore, and the number of trucks hauling ore.The cost of tires is important. Tire companies are manufacturing better tires. Mining companies are prolonging the life of tires by building better roads and maintaining correct tire pressure.The trend is toward heavier equipment. In 1949 it cost $0.0925 a long ton to haul ore and waste with a 15-ton truck and $0.0743 a long ton with a 22-ton truck.When trucks are properly maintained, hauling costs do not increase with the age of the trucks. During 1948 it cost $0.1118 per long ton to haul with the four oldest 15-ton trucks and $0.1130 per long ton to haul with the four newest 15-ton trucks, two of which were purchased in 1945 and two in 1947.The weighted ayerage cost of hauling a long ton of ore to the crusher and waste to the dump has been reduced from $0.1159 in 1948 to $0.087 in 1949."

Oct 1, 1950

By Ronald A. Munson

Samples of the naturally occurring zeolites phillipsite, clinoptilolite, erionite, and chabazite have been surveyed for their gas adsorption, ion exchange, and other characteristics. Chabazite and erionite, which are generally more stable, also have higher methane adsorption capacities than do the other natural zeolites. Both natural erionite and natural chabazite are classified as small-port zeolites on the basis of their inability to adsorb chlorotrifluoromethane. In the range of 8 to 100 mesh, the adsorptive capac-ity of natural zeolites is improved only slightly by a decrease in particle size. The capacity of natural clinoptilolite to adsorb methane is increased by cation replacement by the hydrogen ion and decreased by exchange with calcium ion. Natural phillipsite, which is easily decomposed by heat, adsorbed methane to a limited extent.

Jan 1, 1973

By Ivan L. Nichols

Tailings dumps at Mercur, Utah, contain about $7 million worth of gold in 3.5 million tons of mill tailings assaying about 0.07 ounce of gold per ton. Commercial mining and milling at Mercur ceased in 1942. To determine whether improved technology was now available that might permit economic reprocessing of the Mercur dumps, the Bureau of Mines probed for a low-cost method that would be applicable to these tailings. A composite sample prepared for laboratory studies assayed 0.062 ounce gold per ton. About 10 percent of the gold occurred as a water-soluble cyanide. Conventional cyanide leaching dissolved 32 percent of the gold, and hot, strong cyanide solution dissolved 42 percent. Results were not improved by pretreatment with acids, bases, or oxidants. After expensive preroasting, gold recovery by cyanidation was increased to 65 percent. The simple procedures were ineffective, and more effective procedures were too costly for economical processing of Mercur tailings.

Jan 1, 1970

By Paul A. Pierce

In 1984, the Bureau of Mines evaluated an area previously identified as having "probable mineral resource potential" for copper, lead, zinc, gold, or silver within the Elkhorn Wilderness, about 5 miles west of Winston, MT. The purpose of this study was to determine whether the mineralized structures at nearby mines and prospects outside of the Wilderness extend into and contribute to the anomalous zone and, if so, to expand the domestic supply of strategic and critical mineral resources for future needs by identifying and quantifying resources on public lands. Fifty-eight soil samples, 23 rock samples, and 1 stream sediment sample were collected in the Staubach Creek area. Overall sample analyses suggest the anomalous zone in the Staubach Creek drainage is possibly associated with -.mall pyritiferous quartz veins. These veins or veinlets may be part of a system of northeasterly-trending structures prevalent in this art of the Wilderness. However, there is not sufficient evidence to prove that identified resources outside of the Wilderness extend into it in the Staubach Creek drainage, or that economic base- or precious-metal deposits are likely.

Jan 1, 1987

By Marting J. Gavin

The twentieth century has often been spoken of as the age of petroleum, and from many viewpoints it can be justly considered so. Certainly the petroleum industry is one of enormous importance to this country, industrially, financially, and economically. The United States, however, at present producing over 60 per cent of the world's total output of petroleum, is not producing petroleum at a sufficient rate to provide for its own domestic, consumption. For several years this country has been importing increasing quantities of crude and partly refined oils from Mexico, and has been drawing heavily on domestic stocks of petroleum. Production in the United States is increasing, but it is not increasing at the same average rate as domestic consumption, nor is it probable that in the future domestic production will increase sufficiently to satisfy the demands of domestic consumption, but on the contrary, in the opinion of those best qualified to know, the peak in the curve of domestic production of crude petroleum will be reached in a comparatively few years, whereas the consumption of petroleum and its product will increase at a continually growing rate. This country, then, must turn, and as the increasing imports from Mexico indicate, is turning to other sources than the crude petroleum, produced in this country to make up the deficit between domestic production and domestic consumption of petroleum and its products,

Jun 1, 1920

By J. Ribovich

The current Bureau of Mines active list of permissible explosives includes 71 brands. Eleven are gelatinous, 56 are the granular type, and four are water-gel explosives, an entirely new type of ammonium nitrate-based explosive for use in coal mines. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1973

By J. B. Littlefield

This study is one of a number conducted to determine the concentration of dust in the air during the complete cycle of operation in wet drilling information as to various factors connected with drilling in mining operations is considered to be of definite value in the control and prevention of air dustiness, and it is particularly desirable to ascertain What features of present-day wet-drilling operations in mine work contribute to dust disease and to remedy deficiencies when they are found. ACKNOWLEDGMENTS A testing alit through rock strata is being developed by the Mining Division of the United States bureau of Mines at Mount Weather, Va., and the tests discussed in this report were conducted there. This experimental alit in rock, constitutes a typo of laboratory where mine conditions can be closely simulated and where many of the variables likely to occur in an actual mine can be eliminated or at least controlled with reasonable effort, thus affording maximum opportunities to secure fundamental data uncomplicated by extraneous conditions. The authors wish to acknowledge the valuable assistance and cooperation of several members of the Mining Division, particularly C. F. Jackson, chief engineer, McHenry Mosier, associate mining engineer, and G. E. McElroy, supervising engineer, mine ventilation.

Jan 1, 1938