Search Documents

By M. J. Ferrante

Low-temperature heat capacities and high-temperature enthalpies were determined calorimetrically for Na2Cr04, A reversible transition was found at 700° K with an isothermal heat of transition of 2,263 cal/mole. High-temperature X-ray diffraction analysis showed that the transition was a crystal change from the low-temperature orthorhombic form to the high-temperature hexagonal form. At 795° K the hexagonal form had the parameters a, = 5.691 and co = 7.478 A. Powder diffraction data for the high-temperature form are given and possible structures discussed. The melting point was determined to be 1,065° K with a heat of fusion of 5,810 cal/mole. Enthalpy and entropy increments from this investigation were combined with other data from the literature to calculate enthalpies of formation, free energies of formation, and equilibrium constants of formation from 298° to 1,400° K. Equations that represent enthalpies above 298° K are given.

Jan 1, 1972

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least-radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By A. W. Kbair, L. D. Gehl

"INTRODUCTION The rock-bit interaction during the cutting process in underground mines has been a matter of great concern to mining operators, researchers and manufacturers, particularly after the passage of strict environmental laws. Coal cutting bears directly on airborne coal dust generation and rock cutting generates frictional sparks which may cause face ignitions, jeopardizing the productivity, safety and economy of the industry. It is imperative to investigate into the factors which have influence on bit we.ar. Hurt and Evans (1981) concluded that the point attack bits have greater ignition potential than the conventional wedge shaped bits, and also worn bits were more responsible for ignition than the new bits. The results of a study (Khair et al., 1992) suggested that after 7% weight loss, the bit should be replaced. The polycrystalline compact diamond (PDC) tipped bits are reported to be cost effective in a study done by USBM (Twin Cities Research Center), and it was stated that the PDC tipped drill bits had 80 to 100 times longer life than the ordinary tungsten carbide (WC) tipped bits.This paper presents the results of the experiments which were conducted utilizing a coal cutting simulator at the laboratory of the Department of Mining Engineering, West Virginia University, USA. The description of the machine and the experimental set-up have been described elsewhere (Khair et al., 1989; Gehi & Khair, 1994), and therefore, will not be discussed here. The rock types which were used in experimen~ are Tennessee sandstone, Berea sandstone and Indiana limestone. The operating parameters include (1) drum speed, (2) water spray pressure and (3) bit type. Besides studying the wear characteristics influenced by the above mentioned variables, the effect of these parameters on the required cutting force, specific energy consumption, acoustic emissions rate and rise in temperature of the bit were also studied. A preliminary study was also done to compare we.ar characteristics of the WC bits with those of the poly-crystalline compact diamond tipped bits."

Dec 1, 1995

By C. H. Herty

[Ferromanganese continues to be in indispensable requirement in steel manufacture. Approximately 470,000 tons of the 80 per cent ferro-alloy was consumed in 1929 and increasing amounts will be required annually by the steel industry unless some satisfactory substitute is found. An average of 14 pounds of metallic manganese is for each ton or steel produced, The principal use of manganese is for deoxidation of the metal in the steel refining processes, although a considerable amount r s also used for the production of special manganese steels. Unfortunately, domestic production of manganese ore is inadequate to meet normal peace-time requirements, not to mention increased abnormal war-time demands.]

Jan 1, 1930

By Steven J. Page

Accurate measurement of workplace respirable dust concentration is an essential step in eliminating lung disease in any occupational setting. In the United States (U.S.) coal mining industry, this measurement process has relied upon a personal sampler that includes a 10 mm Dorr-Oliver (DO) nylon cyclone operated at a flow rate of 2.0 L min-1 to collect a respirable dust sample. Dust concentrations measured with this sampler are multiplied by 1.38, which was empirically derived, to convert them to measurements approximating the United Kingdom British Medical Research Council (BMRC) definition of respirable dust upon which the health effects of coal mine dust are based. The International Organization for Standardization (ISO) subsequently refined the respirable dust definition and the U.S. National Institute for Occupational Safety and Health (NIOSH) 1995 Criteria for a Recommended Standard presented a conversion multiplier of 0.857 to apply to the 2.0 L min-' DO (in addition to thel.38 multiplier) to obtain equivalent ISO concentrations, as approximated by the 1.7 L min-1 DO. However, the conversion multiplier 0.857 was derived indirectly from a limited size distribution data set rather than a direct comparison of the DO samplers. The present analysis focuses on providing a more accurate conversion multiplier derived from direct comparisons of the 2.0 L min-1 (with 1.38 BMRC equivalency multiplier) and 1.7 L min-1 DO cyclones. A weighted linear regression analysis of this database suggests that a more accurate estimate of the conversion multiplier is 0.815.

Jan 1, 2009

By Jr. Herty

Ferromanganese continues to be an indispensable requirement in steel manufacture. Approximately 470,000 of the 80 per cent ferro-alloy was consumed in 1929 and increasing amounts will be required annually by the steel industry unless some satisfactory substitute is found. An average of 14 pounds of metallic manganese is used for each ton of steel produced, The principal use of manganese is for de-oxidation of the metal in the steel refining processes, although a considerable amount is also used for the production of special manganese steels. Unfortunately, domestic production of manganese ore is inadequate to meet normal peace-time requirements, not to mention increased abnormal war-time demands. The rather large quantities of low-grade manganiferous iron ores which occur in the Coruna Range in Minnesota have for a number of years greatly appealed to those interested in the development of a domestic source of the supply. The North Central Experiment station of the Bureau of Mines has made an elaborate study of the possibilities of the pyrometallurgical treatment of ores from these deposits and much of the valuable information secured by them has already been published.

Jan 1, 1930

By R. E. Meaker

Electrical conductivities and densities of molten fluoride systems were measured as functions of the melt temperature and composition. For any given mixture, the two properties change linearly with temperature. Three alkali metal fluorides were selected as solvents for melts of the type LiF-, NaF-, and KF-MFx, where M is a metal selected from the alkali metal or alkaline earth groups, or from the lanthanide or actinide series of elements, and x = 1-4. Heats of activation for conductance were calculated from the experimental data and varied from 2.3 to 9.2 kcal/mole at 1,000° C. Some relation between position in the phase diagram and the conductivity changes was suggested.

Jan 1, 1971

By Robert Blickensderfer

Equipment and procedure for the continuous roll bonding of metal strips are described. The reels, mill rolls, and furnace were located within a vacuum chamber capable of operation at a residual gas pressure of 1 x 10-4 to 1 x 10-5 torr. Several metals were successfully clad at rolling temperatures of 930° to 1,050° C in lengths up to 120 ft. The bimetals that were clad included stainless steel to carbon steel, molybdenum and nickel to stainless steel and carbon steel, and titanium to carbon steel. Bend tests of bond integrity are described, and microstructures of the interfaces are presented. The amounts of brittle intermetallic phases formed at the interface are minimized by this cladding method.

Jan 1, 1980

By Oliver Bowles

Slate possesses many admirable qualities, not only as a roofing material, but for blackboards, electrical switch boards, and for various structural uses such as stair trends, floor tile, baseboards, and sanitary enclosures. The American slate industry was established manor years ago, and has made remarkable progress, particularly during the past five years. One of the chief drawbacks to more rapid expansion is the high percentage of waste which reaches 75 to 94 per cent of gross production. Much of this waste is duo to rock imperfections over which man has no control, but a careful study of tae industry by the Bureau of Mines over a period of years indicates that an undesirably large percentage of the marketable slate is wasted in the processes of quarrying and manufacture. The initial step in quarrying slate is to separate from the solid ledge masses of a size that ray be conveniently removed from the quarry. This first step entails a greater waste of material than any subsequent process, and, therefore, invites the most earnest effort toward waste reduction. Attention has consequently been directed toward possible improvements in methods of making primary cuts in the quarry floor. A study of European practice with the wire saw, together with theoretical consideration of its advantages, convinced the writer that it possessed sufficient merit to justify its use as a primary slate cutter in American quarries. No practical conclusion in this matter could be reached except by experiment. Therefore, the desirability of obtaining equipment and trying it out under actual conditions of operation was urged upon operators. While no doubt the equipment could be readily manufactured in America, it had already been developed to the point of practical use in Europe; therefore the writer urged the desirability of purchasing one completely equipped wire saw in Europe, and determining through tests whether it gave sufficient promise of success to warrant its manufacture in America.

Jan 1, 1927

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least- radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By R. L. Grant, R. W. Van Dolah, N. E. Hanna

An experimental investigation was conducted to assay the relation between natural gas concentration and ignitibility of the gallery atmosphere . Both the gas concentration representing maximum ignitibility and the relationship between certain properties of the explosives and their incendivity are discussed . The data show that variation in the natural gas content in the gallery can have a highly significant effect on ignitibility of the gallery atmosphere ; maximum ignitibility of the atmosphere by permissible explosives occurs with approximately 8.1 percent natural gas . The study also shows that incendivity of a permissible explosive cannot be determined only by its detonation velocity , oxygen balance , or ballistic mortar strength . However , for similar type explosives , trends observed indicate that their incendivity increases with detonation velocity or bulk strength . Additionally , for underoxidized explosives studied here , the more negative the oxygen balance the less incendive was the explosive within a class defined by salt content .

Jan 1, 1963

By M. R. Geer

The ever-increasing need to guard against stream pollution has intensified interest in the problems of handling and disposing of flotation tailing. Therefore, the Bureau of Mines investigated the possibility of using crushed washery refuse to adsorb the free water in thickened flotation tailings on a bench scale and then in a pilot plant because the conventional methods of disposing of coal flotation tailings--impounding them or filtering them so they are dry enough to be conveyed to the refuse dump--are sometimes either impractical because of space limitations or costly because of low filter capacity. Most of the refuse samples tested were of similar mineralogical composition and exhibited similar water retention capability. The amount of crushed refuse required to adsorb the water in a particular tailing was influenced greatly by the fineness of the solids in the tailing and hence the percentage of solids to which it could be thickened. The ratio of crushed refuse to tailing solids required to provide a mixture dry enough to be carried on an inclined conveyor belt varied from 2.4 to 6.4. Several chemical agents that were tested were very effective in turning the free water in tailings into a stable gel. Fly ash also was very effective in adsorbing water.

Jan 1, 1968

By K. K. Kershner

The purpose of this investigation was to develop methods on a laboratory scale for recovering tin from metallurgical slime, Tin chlorides were volatilized using mixtures of hydrogen chloride and reducing gases, such as hydrogen, carbon monoxide, hydrogen sulfide, ethane, propane, and butane. Optimum conditions were found to be n mixture of 3:1 of hydrogen and hydrogen chloride at 475° C. Over 95 percent of the tin was volatilized as chlorides. Low temperatures and relatively rapid rates of reaction are distinct advantages of the chloride volatilization process. Research is being continued with various slimes and will be extended to tin ores, where the method offers interesting economic possibilities in comparison with current tin-smelting practice.

Jan 1, 1957

By James P. Bennett

To improve construction materials for emerging chemical and metallurgical technologies, the Bureau of Mines is investigating the acid resistance of ceramic materials. In the study described here, eight commercial ceramic materials comprising two red shale, two fire clay, a silica, a silicon carbide, a carbon, and a high-alumina brick were evaluated. Samples were exposed to 20 wt-pct HC1 at 50° C for 110 days. The test apparatus designed to evaluate the materials is described. Changes in chemical and mineralogical composition, cold crushing strength, volume, and weight, and leach rates of AI, Ca, Fe, K, Mg, Na, Si, and Ti ions were monitored. In general, the statistically significant physical property changes that occurred were small. In many cases, no changes were detected.

Jan 1, 1982

By George W. Hezzelwood

This paper describing the minim, methods at the mine of the Consolidated Cortez Silver Mines, Cortez, Nevada, is one of a series of similar papers being prepared by the Bureau of Mines on mining practices and costs in the various mining districts of the United States. The Cortez district is situated on the southwest slope of Mt. Tenabo of the Cortez Range, near the middle of the boundary line between Eureka and Lander Counties (fig. 1). The camp of Cortez is 36 miles south of Beowawe, the nearest station on the Southern Pacific and Western Pacific Railroads. Mt. Tenabo, which is the highest summit of the south end of the Cortez mange, has an elevation of 9,240 feet; Cortez is about 6,280 feet above sea level. The Consolidated Cortez Silver Mines is the only company operating in the district at the present time and employs about 60 men. The daily production of l25 tons of silver-lead ore is concentrated in the company's mill of 150 tons capacity. The concentrate is hauled to Beowawe by automobile trucks for shipment to a reduction plant in Salt Lake Valley, Utah.

Jan 1, 1930

By W. M. Myers

The U. S. Bureau of Mines conducted an investigation to determine the cause of the deterioration of Portland cement during storage and transportation , and to discover a means of preventing it . All available printed sources of information on this subject have been examined and a bibliography has been compiled . The subject has also been discussed with the leaders in the cement industry ; the present report is the result of their cooperation , and is based principally on information thus obtained . Deterioration of Portland cement during storage over any considerable period of time has long been noted ; closely related to it is deterioration of cement during transportation, which involves not only the time factor of storage but also exposure to varied climatic conditions . Deterioration in both cases is due to hydration of the cement by absorption of moisture from a humid atmosphere , or by exposure to actual rain-fall . After hydration cement possesses no cohesive power ; the degree of deterioration is directly proportional to the degree of hydration . The amount of deterioration of Portland cement during storage has been accurately determined in an investigation by the Structural Materials Research Laboratory , in cooperation with the Portland Cement Association . Cement stored in a shed in cloth sacks retained 80 per cent of its original strength after three months storage ; 71 per cent after six months ; 61 per cent after one year ; and 40 per cent after two years . The deterioration of Portland cement during storage and transportation was noted particularly in France during the World War . Information concerning cement used by the American Expeditionary Forces was furnished by Lt. Col. H. S. Spackman and Major E. C. Eckel , U. S. R. , who had charge of practically all matters concerning cement used by the A. E. F. The cement used by the A. E. F. came from the following sources : 42,000 tons was French , Swiss , and Spanish cements ; 120,000 tons was English cement ; 55,000 tons made in plants operated by the A.E.F .; 500 tons ( Not over) from America . Deterioration was most marked in cement from the first source .

Jun 1, 1922

By C. W. JEFFERS

During the past few years the use of mechanical equipment for the loading and transportation of coal at the working face has rapidly increased . Many mining officials are of the opinion that mechanical methods have tended to reduce the hazards of mining, and a number of statements have been made to this effect . Little actual data upon which to base conclusions in regard to the relative safety of various methods of mining have been made available . While it may be possible that these systems of mechanical mining are inherently less hazardous , obvious dangers should not be disregarded in the belief that the mere act of installing mechanical loading equipment automatically brings about better accident records . The same rules and regulations , modified to meet the new regime must be applied with the same discipline as heretofore . By diligent study and application there is reason to believe that new methods of concentrated mining can be utilized with at least a possibility of increased accident performance . With the idea of preventing accidents by taking available precautions against their occurrence , attention should be directed to the dangers that exist where room and face conveyors are in operation . Due to the cost pressure prevalent in the mining industry at the present time mechanical means are often used in an attempt to decrease cost of production. The management , after having spent considerable sums of money for new equipment , is expected by stockholders and investors to show results by increasing tonnage and reducing operating costs . Consequently the operating officials apply the same pressure to local mine officials to obtain results . The natural reaction of the superintendent and mine foreman is to secure the maximum production from the new method , and unfortunately safety is frequently , if not generally , sacrificed to this end . In many instances , operators of new types of mechanical loaders are difficult to secure and after being obtained are difficult to hold , especially if the new equipment is more or less in the experimental stage . The tendency is to handle the machine operators with " gloved hands " and to permit many unsafe practices which ordinarily would not be allowed, in order to keep from antagonizing them and losing their services . Although these unsafe practices become habitual and even uneconomical , conditions thus established are difficult , sometimes impossible , to change .

Jul 1, 1930

By F. Cherpereel, R. Gabillard, J. P. Dubus

We present an electromagnetic method taken from the well known radiogoniometer that allows us to locate at the surface of the ground the vertical axis of a magnetic antenna transmitter buried at a depth h in the earth. The method and the equipment achieved are called R. E. P. E. (Relevé Electromagnétique de Points Enterrés). They are daily used to accurately survey old quarries by using triangulation instruments at the surface of the earth rather than in galeries where the setting difficulties considerably reduce their accuracy and increase the work length. The results of several surveys allow us to give the optimum working conditions of the instruments and show that, when the transmitter is at a 20 meters depth, its position is known at the surface with an error lower than 1 centimeter. The power transmitter is of about 8 watts and we can find its location with an error smaller than 1 meter when buried at a depth of about 100 meters. This equipment may be successfully used for location of subsurface miners. The space surrounding the transmitter must then be free from ferromagnetic bodies.

Jan 1, 1973

By W. E. Young

This paper describes operations of the Chief Consolidated Mining Co. at the Chief mine in the Tintic district, Juab County, Utah, where the outstanding problem is water control; the unique pumping methods employed are featured in this report. The ore bodies in this district occur as long, narrow shoots along fault fissures, usually in the Bluebell dolomite of Ordovician age. Oxide ores predominate above the 1800 level, which is also the natural water level. Sulfide ores containing lead, zinc, silver, and gold extend below the 1800 level. The mine is developed by vertical shafts and winzes, from which drifts are driven to the ore bodies. In the lower levels of the mine these drifts extend long distances from the shafts or winzes because of the relatively low dip of the ore shoots. The mine has been worked to the 2800 level and the 18-411 winze extends to the 3080 level.

Jan 1, 1958

By Raymond B. Ladoo

The uses of talc are many but are not, in general well known or fully developed within the last decade several companies have realized the possibilities of greatly increased use and have intelligently proceeded to develop some of the fields which seemed most promising. This has had a tendency to lift talc from the obscurity in which it had existed for years, but the work is only started and much remains to be done. Considerably more attention has been paid to the technology and utilization of talc in Germany and Austria than in this country, despite the fact that the United States produces 65 of the world's talc and Germany and Austria combined but 5.4%. In the "Bericht,uber die tatigkeit des verbends der talcum-interessenten in Oesterreich-Ungarn" (Proceedings of the Austro-Hungarian Talc Association), for the years 1912 and 1913, many notes upon new uses appeared, together with suggestions as to further development of old uses. Aside from a few notes on the use of tar in paper, little has been published in the English language upon this subject. By recent action of the Talc and Soapstone Producers Association (U.S.A.) funds for research into the properties and uses of talc have been made Available and it is hoped that markets will be materially broadened a a result of this work.

May 1, 1920