Search Documents

By Richard D. Miller

The helium resources base of the United States was estimated by the Bureau of Mines to be 961 Bcf as of January 1, 1983. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas re- serves, 271 Bcf, (2) helium in probable natural gas resources, estimated at 202 Bcf, (3) helium in possible natural gas resources, estimated to be 351 Bcf, and (4) helium in speculative natural gas resources, which makes up the remaining 137 Bcf. These helium resources are further divided into depleting, nondepleting, and stored classifications. The depleting resources are those associated with natural gas fields that are, or will be, produced for the natural gas they contain. All of the helium in potential (probable, possible, and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 789 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, those in shut-in, abandoned, or otherwise nonproducing natural gas fields, are estimated to total 134 Bcf. There is 38 Bcf of helium in storage in the Federal Government- owned Cliffside Gas Field near Amarillo, TX.

Jan 1, 1985

By H. G. Wolfhard

The mode of propagation of explosions through narrow passages is important for understanding flameproofed equipment employed in mines. Narrow channels have been used in this investigation that connected between a small explosion chamber and a large chamber containing fuel-air mixture. The oxygen index of the mixture in the small chamber was determined which caused an explosion in the outer chamber. Preliminary measurements have already been given in Bureau of Mines Report of Investigations 5457 and suggested that) flames do not pass through narrow channels. The hot, burned gases from the explosion in the small chamber, however, are able to ignite the mixture in the large chamber by a process of hot-gas ignition. Systematic measurements are reported in the present paper that cover the influence of channel length and diameter and the properties of the gas mixtures in the large chamber on the transmission of explosions. The influence of such properties as quenching diameter and flame temperature is also discussed. This paper concludes the work on this problem and presents a theory that describes in detail parameters that influence transmission of explosions through narrow channels. INTRODUCTION Flameproofed equipment in mines is usually provided with flanges. A gap between the opposing flanges allows ventilation and release of pressure. The safe gap width has been determined for a number of flange lengths by Smith4/

Jan 1, 1959

By P. C. Van Natter

Numerous mine fires have resulted in high death tolls and considerable finan¬cial loss during the history of coal mining. In most instances the death toll and financial loss were greater because of inadequate fire-fighting facilities. The information in this report is presented in the hope it may serves as a guide in the selection, placement, and care of fire-protection systems in similar coal mines. The adequacy of fire protection varies according to size of operation, employment, and production. When fires occur on the surface or underground, measures must be applied quickly to prevent incipient fires from spreading. The record of coal-mine fires shows that, in many instances, facilities for combating fires were very meager or were absent. It would be virtually impossible to establish and maintain all the necessary facili¬ties that may be needed to extinguish widespread mine fires, but it is believed that the coal industry can ill afford less than the minimum required by other industries where the time element and avenues of escape are much more favorable.

Jan 1, 1958

By Paul B. Harder

Round Mountain Gold (RMG) in central Nevada, reports that over a nine-year period and a million operating hours, its fleet of 150-ton and 190-ton haul trucks has averaged better than 93% availability, with some of the trucks approaching 70,000 operating hours. Repair costs have been far below industry averages. Mine operations manager Pete Kesl credits the high availability and low repair costs to a succession of Product Support Agreements between RMG and Caterpillar dealer Cashman Equipment. He adds that good equipment and a high level of trust and co­operation between all parties to these agreements have been essential to their success at Round Mountain.

Jan 1, 1998

To suppress the natural bacterial action in acid mine drainage (AMD), the major contributor to acid formation. Approach Recycle partially-treated affluent back to the source of AMD within a mine, or to the coal or coal-waste stockpile. This effectively eliminates any further biologically-promoted AMD by inhibiting catalyzed weathering or oxidation by acid-forming bacteria. How it Works AMO-type effluents can be largely reduced by "recycling" the acidic outflow back to the source of AMD within a mine or to the Input side of a waste pile to percolate through the reactive pyrite and bacteria mixture. The bacteria in the cell thrive on the oxidation of ferrous to ferric iron through the electron transfer, Fe2 +[=]Fe3 + + e. Its reaction product [s, therefore, essentially ferric iron. While small quantities of Fe3 + will not interfere with the exponential multiplication of the bacteria

Jan 1, 1982

By Steven J. Schatzel

Gas drainage through surface bore-holes has been the conventional means of methane control for U.S. longwall gobs. However, these vertical boreholes are becoming so costly, and the surface rights so difficult to obtain, that the Bureau of Mines is developing underground gob gas drainage as an alternate means of methane control for U.S. longwalls. Holes are drilled into the roof over the panel and on retreating longwalls, towards the working face from a location inby the face. As the longwall retreats, an increasing portion of the hole intercepts the fracture system over the caved gob. A surface exhauster maintains a vacuum on a pipeline parelleling the panel and draws the methane mixture out of the mine. Auxiliary systems of gob gas drain-age during longwall mining will be essential for an increasing number of coal mines. Deep and gassy mines often find ventilation insufficient for adequate dilution of methane in bleeder entries. Although this cross-measure method of degasification has been used successfully in Europe, some of the European techniques cannot be directly applied to U.S. mines. This is the first study of its kind in this country.

Jan 1, 1982

By Russell C. Frith, David C. Oyler, Dolinar Dennis R., Christopher Mark

Unusual circumstances may require that a longwall retreat into or through a previously driven room. The operation can be completed successfully, but there have been a number of spectacular failures. To help determine what factors contribute to such failures, a comprehensive international database of 131 case histories has been compiled. The cases include six failures where major rock falls occurred in front of the shields, and seven even more serious failures involving major overburden weighting. The case studies suggest two types of room failure mechanism. The first is a roof fall type failure caused by loading of the immediate roof at the face as the fender or remnant longwall panel narrows. The second is an overburden weighting type failure caused by the inability of the roof to bridge the recovery room and face area, and affecting rockwell above the immediate roof. The data indicate that the roof fall type of failure is less likely when intensive roof reinforcement (bolts, cables and trusses) is employed together with higher-capacity shields. The overburden weighting failures, in contrast, occurred when the roof was weak and little standing support was used. Weighting failures were not greatly affected by the density of roof reinforcement. In one of the overburden weighting cases, in a Pittsburgh coal bed mine, stress cell, convergence, bolt load and extensometer data have been used to analyze the failure in detail. Key words: coal mining, ground control, longwall, recovery room.

By L. B. Pankratz

Low-temperature heat capacities, high-temperature enthalpy increments, and the enthalpy of formation at 298° K were determined calorimetrically for vanadium subnitride (VN0.465). The low-temperature investigation gave S°298.15 = 6.379 ±0.005 cal/deg mole, and a combustion calorimeter investiga¬tion provided ?Hf°298.15 = -31.80 ±0.60 kcal/mole. The two quantities were combined with the high-temperature data to give standard values of enthalpies of formation and free energies of formation above 298° K. These and related thermodynamic functions were tabulated to 1,800° K. Similar data are included in the range of 298° to 1,600° K for the mononitride, VN.

Jan 1, 1971

From the National institute for Occupational Safety and Health Disasters take many forms and demand quick response from emergency workers. They may include natural disasters such as earthquakes or hurricanes, or they may involve manmade disasters such as technological failures or terrorist attacks. As a member of an emergency response team, you and your team members are at risk of experiencing what psychologists refer to as a traumatic incident—an incident that may Involve exposure to catastrophic events, severely injured children or adults, dead bodies or body parts, or the loss of colleagues, for instance. Traumatic incidents can produce unusually strong emotional reactions that may interfere with your ability to function at the scene or later: You may experience any of the physical, cognitive, emotional, or behavioral symptoms listed below in Table 1. Some people experience emotional aftershocks weeks or months after they have passed through a traumatic event. Others may experience these reactions while still at the scene, where they must stay clearly focused on constantly changing hazards to maintain their own safety and to rescue injured victims.

By W. P. Haynes

The Bureau of Mines has been studying a modified steam-iron process using coal-derived producer gas for making either hydrogen plus carbon monoxide or methane. To provide a guide for this experimental study, compositions of equilibrium product gases for the reaction of steam plus carbon dioxide with iron were calculated and are discussed in this report. The calculations, which are described in this report, are based on thermodynamic data in the literature and cover temperatures from 800° to 1,300° K., pressures from 1 to 30 atmospheres, and hydrogen-to-carbon atomic ratios in the gas of 4 to 12. The equilibrium gas compositions are discussed in regard to making hydro-gen, carbon monoxide, and methane in the oxidation step of the modified steam-iron process. From the viewpoint of thermodynamics alone, assuming the reactions reach equilibrium, the discussion considers the effects of temperature, pressure, and composition of feed gas upon the composition of the product gas, the degree of oxidation of the iron, and the possible deposition of carbon. The results indicated the following: (1) Nearly all the carbon can be converted to methane at low temperatures (800° to 900° K.) and high pressures (over 20 atmospheres); (2) to obtain high yields of synthesis gas, high temperatures are required. For example, at 30 atmospheres, a temperature over 1,200° K. is required to convert 60 percent of the steam plus carbon dioxide to hydrogen plus carbon monoxide. Lower temperatures may be used at lower pressures) (3) oxidation of the iron increases with increasing pressure and decreases with increasing temperature; and (4) process conditions favoring carbon deposition were found within the range of variables studied, but it is thermodynamically possible to operate the oxidation process with steam and carbon dioxide outside this range of carbon deposition.

Jan 1, 1961

By James E. Hill

In the course of exploratory drilling during World War II by the Bureau of Mines under the Strategic and Critical Minerals investigations Program, a problem arose as to the ultimate disposal of the drill core resulting from that program. The difficulties experienced in obtaining factual information to evaluate mineral deposits examined (during that program) influenced the Bureau in a decision to catalog and store the drill cores for future reference. Initially, the drill cores were stored at the nearest Bureau of Mines station that had space available for the purpose. Recently the Bureau stations at Minneapolis, Minn., and Denver, Colo., were designated as the locations of permanent drill-core storage facilities. Drill cores that are retained from Bureau of Mines mineral-exploration projects are stored at these two locations and are given preference in selecting cores for storage. Drill cores are accepted also for storage from other Government agencies, State agencies, private companies, or individuals on the basis of available facilities and consistent with the significance of the core in relation to Bureau of Mines objectives and national interest. Selection and acceptance of such drill core are determined by the Bureau of Mines. The drill cores stored at the two locations are available for inspection by any person having a legitimate interest in the mineral deposits represented by the cores. Approximately 1,850,000 feet of drill core can be stared in the facilities now available to the Bureau of Mines. Approximately 475,000 feet of drill care is stored or scheduled for storage at Minneapolis, Minn., and 240,000 feet of core stored or scheduled for storage at Denver, Colo. A list of drill core now in storage at the Bureau of Mines core-storage facilities at Denver and Minneapolis is included as appendix A.

Jan 1, 1957

By David C. Byrne

From an engineering perspective an ideal industrial noise control solution focuses directly on the actual source of the poise. Eliminating the noise-generating mechanism altogether obviates the need for other noise contra l treatments or hearing protection devices. However, in cases where attenuating the source is not feasible engineering controls must be oriented toward blocking the path that the sound waves travel toward employees. Acoustical enclosures are commonly used as sound path treatments to contain the noise from a machine: alternatively a control room/booth or equipment operator's cab may be used to isolate the worker from the noise. Anyone who has successfully used acoustical enclosures knows that the design procurement, and installation process is deceptively simple. Alt too often First-time efforts fait to account for many of the constraints that can render the enclosure essentially useless. Things that cannot be overlooked include: providing convenient worker access (physical and visual): allowing for proper machine operation/product flow; and supplying fresh air or preventing undue heat or contaminate build-up inside the enclosure. All of these factors must be given careful consideration, otherwise the enclosure will not perform adequately.

By J. D. Dixon

The Bureau of Mines investigated the principles of support-rock interaction, based on structural matrix methods which permit mathematical formulation of the problem and computer solution. The principles are given under two main sections: the first discusses the idealization of the tunnel support structural system for matrix analysis; the latter discusses the analysis procedures necessary for carrying out the solution. A general frame matrix computer program and a medium-size computer should be sufficient for carrying out the procedures involved. The example problem consists of a circular tunnel support which is subjected to a uniformly distributed vertical load, Three wall thickness-radius ratios are studied in combination with four support-rock modulus ratios. This problem illustrates the main procedures of the support-rock interaction analysis involved, and examination of the results reveals the influence of the relative rigidities of the support and the rock.

Jan 1, 1971

By Fred N. Kissell

Methane concentration peaks were measured by the Bureau of Mines at coal mine working faces during entry development. The statistical distribution of peaks was found to be normal or log normal depending on how well the methane was being mixed into the ventilation airstream. A normal distribution indicated good mixing, whereas a log-normal distribution indicated that mixing was poor. In addition, the "highest" peaks over selected intervals were found to fit a type I extreme-value distribution, a result similar to that obtained while mining longwall faces.

Jan 1, 1974

By B. S. Covino

The Bureau of Mines, U.S. Department of the Interior, is conducting research to devise substitute corrosion-resistant materials by using ion implantation to form alloyed regions near the surfaces of metals. These alloys were prepared by implanting 25-kev Cr+ and/or Ni+ ions into iron. Their resistance to corrosive attack was evaluated by determining their anodic polarization behavior under potentiodynamic conditions in a solution containing sodium chloride, boric acid, and sodium borate. These electrochemical studies have shown that the general corrosion resistance of ion-implanted alloys was comparable to nominally equivalent bulk alloys. The pitting-corrosion resistance of the ion-implanted alloys was superior to that of iron, although not as good as that of most of the bulk alloys tested.

Jan 1, 1980

By James R. Aggson

The theoretical relationships that are used to calculate in situ rock stress magnitudes and directions from borehole deformation data obtained during overcoring are based on the assumption that the rock is a linearly elastic material. Strictly speaking, this assumption is not valid in any rock. Thus, investigators using overcoring techniques must either accept various degrees of nonlinearity and the associated inaccuracies or use core testing techniques that address the problem and compensate for elastic nonlinearity. Previously developed test procedures for stress-relief overcores partially correct for nonlinearity. This Bureau of Mines paper describes a test procedure that completely corrects for elastic nonlinearity in stress-relief overcores.

Jan 1, 1977

By John F. Papp

The Bureau of Mines has sampled microstructure of low-pressure flat flames by mass spectrometer for normal methane-oxygen-argon and for methane-oxygen-argon-bromotrifluoromethane flames. The physical and chemical phenomena, and the method of analysis of mole fraction data to evaluate net reaction rates are here considered in detail. Included is a computer program listing with output on one flame. Chemical species considered are CH4 , CO, CO2, H, H20, OH, Ar, H2, O2 , O, H2CO, CH3 , CF3Br, HF, HBr, Br, CH3Br, HCO, F2CO, CH2 CF2 , H02.

Jan 1, 1975

By J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 3S0 meters (1150 ft.) and 488 meters (1600 ft.). The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broadband, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or F layers of ionosphere as an upper plane and the earth as a lower plane.

Jan 1, 1974

By John Durkin, Roy J. Greenfield

This report discusses the configuration and system deployment for the postdisaster surface seismic system for detecting and locating trapped miners. It analyzes the results of 15 field tests to define a signal model, background noise levels, and subarray performance. A waveform modeling procedure is described and compared with observed waveforms. The resulting similarity indicates that the major factors affecting the signal amplitude, waveform, and spectral character are understood. A model is presented which gives the signal amplitude as a function of source type, source depth, and horizontal off- set between source and receiver. Using this model a curve is presented which gives the range at which a signal will be detected for different signal and noise levels. Finally, and most important relative to the mission of the sys- tem, the ability of the system to detect signals on one or more subarrays is put into a probabilistic framework. For a strong source it is almost certain that a subarray directly over the source will detect the signal. After signal processing, it is highly likely that signals will he detected on sufficient subarrays to locate the trapped miner. Location errors have been found to be less than 100 ft in the majority of cases. Techniques have been used that can reduce the location errors to this level even when soil layer variation between subarrays is severe.

Jan 1, 1981

By W. T. Abel

The Bureau of Mines tested 48 materials for their ability to absorb H2S from hot simulated producer gas (1,000°-1,500° F). The material found best from the standpoint of absorption capacity, durability, and amenability to regeneration was sintered pellets of 75 percent fly ash-25 percent Fe203. The performance of this absorbent under simulated and actual conditions is described. The effect of absorbent composition, absorbent temperature, steam content of the gas, and tar vapors and dust in producer gas is discussed.

Jan 1, 1974