Search Documents

By L. A. Morley

Volume III of the final report examines the indication versus interruption procedures used on motion-drive power equipment, with emphasis on surface excavators. The report begins with a review of the electromechanical acid conversion used with the Ward-Leonard control system. Protection criteria for the drive-system components are then discussed. Fault sources and fault calculations for both the ac supply source and dc power loop are introduced to assist in discussing indication and interruption procedures. The subject is then expanded to examine the dynamic process of the machine and determine the effects of fault current and position of the machine to allow for an orderly shutdown. With this analysis, possible indication an interruption procedures are given for the four-quadrant duty cycle of excavators. The report concludes by introducing other mining operations that utilize similar motion-drive systems and also static (solid-state) drives and recommends further research in these areas, as well as a more detailed examination of the dynamic fault analysis for excavators.

Jan 1, 1982

By T. A. Sullivan

High-purity vanadium metal was prepared by electrorefining commercial vanadium in a molten sodium bromide, potassium bromide, and vanadium dibromide electrolyte. Variables investigated were operating temperature, current densities, electrolyte composition, and condition of the anode. The purity of the refined metal was in the range of 99.95 percent vana-dium. Iron and oxygen in the 50- to 250-ppm range were the only major impurities. Metal with hardness numbers of 50 to 60 in the Rockwell F scale was prepared from feed material with a Rockwell B hardness of 90. The arc-melted metal was highly ductile and could be cold-worked into sheet or foil.

Jan 1, 1965

By S. R. B. Cooke, J. Bruce Clemmer, F. P. Diener

"The limestone deposit utilized by one of the plants of the Universal Atlas Cement Co. is covered in part by a stratum of cherty limestone. If this overlying deposit could be utilized by removing the excess of chert economically, quarry costs could be reduced and the amount of rock economically available would be increased greatly. On account of the distribution of flint and limestone, a product fairly free of flint can be obtained until the quarry face is about 50 or 55 feet high. As the face is worked farther back into the hill, the comparatively clean stone is overlain with a constantly increasing amount of high-flint limestone. If this flint remained with the limestone, there would be a prohititively high silica ratio in the finished cement; if the flinty layer were removed as overburden a very large tonnage would be handled and much good stone lost. Consequently it was felt that means should be devised for separating the flint from the limestone after it reaches the plant.The investigation was undertaken by the Mississippi Valley Experiment Station of the United States Bureau of Mines in cooperation with the Universal Atlas Cement Co. and the Missouri School of Mines and Metallurgy, Rolla, Mo.CONSIDERATION OF PROCESSESMany schemes for the separation of Minerals are based on differences in the specific gravities of the minerals to be separated. In this case the flint has a specific gravity of approximately 2.62 while the limestone averages about 2.70. This differential is not large enough to permit separation by any method based on specific gravity. Furthermore, all the limestone particles in any given sample are not alike; usually about 10 percent of them have a specific gravity the same as, or lower than, the flint."

Mar 1, 1935

By J. G. Donaldson

Binary alloys of molybdenum and tungsten were prepared by the Bureau of Mines in laboratory-scale experiments by hydrogen reduction of their vaporized hexafluorides. Near-optimum deposition parameters were determined, and the nature of the deposited alloys was investigated. Dense, homogeneous alloys were codeposited between 650° and 750° C with a reduction efficiency of more than 75 percent. The alloy composition was uniform when the hydrogen ratio in the gas feed mixture did not exceed 3 times the stoichiometric requirement. Regulating the proportions of the metal hexafluorides in the gas feed provided a large degree of control over the composition of the deposit. Hardness of the deposits varied directly with the proportion of excess hydro,,,, in the gas feed and with the weight-percent of tungsten in the alloy. Hardness was not affected by deposition temperature over the range 650° to 750° C for specimens of similar composition. Extreme brittleness and unsuitable physical shapes of the alloys prevented tensile strength measurements.

Jan 1, 1966

By Harry Freund, Kenneth H. Hammill, Francis C. Bissonnette

"Gallic acid is a sensitive, stable, colorimetric reagent for the determination of tantalum in the range of 2 to 40 µ g.Ta/ml. The method consists of the fusion of tantalum oxide with potassium pyrosulfate and solution of the cooled melt in saturated ammonium oxalate, followed by development of a yellow complex with an ethanolic solution of gallic acid. The tantalum-gallic acid complex absorbs over a broad region in the blue and near ultraviolet. Adverse effects due to interfering ions and solution conditions, such as oxalate concentration and pH, can be minimized by a suitable choice of wave length.by a suitable choice of wave length.A new and sensitive colorimetric method is provided that has been used successfully at the Northwest Electrodevelopment Laboratory of the Federal Bureau of Mines for determining minor amounts of tantalum.INTRODUCTIONThe development of corrosion-resistant alloys at the Northwest Electrodevelopment Laboratory prompted a review of the analytical chemistry of columbium (niobium) and tantahnn. Not only are these elements difficult to determine in small amounts, but tantalum especially lacks both sensitive and characteristic color reactions. Various phenolic compounds have been suggested as colorimetric reagents for tantalum, Quentin and Wagner (10, p. 24B) 1/ recommend the use of tannin. The use of pyrogallol was suggested originally by Krivoshlykov (6, pp. 59-60), whose method recently has been subject to a number of modifications (3, pp. 249-254; 5, pp. 1340-1344; 1, pp. 1803-18oi; 4, pp. 345-350). The yellow coloration produced by pyrocatechol in an oxalate solution containing tantalum may also be used to estimate tantalum ( 11, pp, ll-1-4-148) . The use of hydrogen peroxide has been recommended also (7, pp. 164-165; 9, pp. 926-931).Aside from a lack of specificity and sensitivity, the major failing of phenolic reagents is their susceptibility to air oxidation. The oxidation products are highly colored and absorb in the same spectral region as the tantalum complex. Holding reductants are not completely satisfactory in minimizing this effect. Increasing the acidity, while retarding the oxidation, has an adverse effect on the tantalum sensitivity."

Sep 1, 1956

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents, and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and periodically publishes health and safety statistics. This report includes data for 1963 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following headings: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1966

By T. M. Nasiatka

This report sterns from a study undertaken by the Federal Bureau of Mines to determine the possibility of reducing filter-cake moisture by applying radiant heat. Suitable laboratory equipment was set up to study the effect of heat, heating time, proximity of the heater to the filter cake, cake thickness, and other variables related to the final filter-cake moisture. A minus-48-mesh coal slurry and application of heat for 60 seconds resulted in filter-cake moistures 5.6 to 13.2 percentage points lower than could be accomplished by filtration alone at 24 inches of Hg for 1-1/4-and 1 1/2-inch cake thickness, respectively. The moisture reduction can be attributed to the combined effect of lower fluid viscosity and evaporation.

Jan 1, 1959

By P. L. Woolf

An investigation was conducted to evaluate the use of a formcoke as the total fuel in the Bureau of Mines experimental blast furnace. The formcoke performed very satisfactorily, and comparisons made with a metallurgical coke showed that the performance with the formcoke was somewhat superior under the experimental conditions used.

Jan 1, 1966

By J. M. Stuve

Calorimetric data for the dissolution of scandium sesquioxide and scandium trichloride in 4.360 molal hydrochloric acid were used to evaluate the standard heat of formation of ScCl3(c). The heat of reaction for Sc(c) + 1.5Cl2(g) = ScCl3(c) at 298.15° K was computed as -225,440 ±340 cal/mole.

Jan 1, 1965

By S. J. Page, W. R. Reed, J. A. Organiscak

NIOSH continues to conduct respirable dust control research for surface mine blasthole drilling operations. Research areas have included testing variables (shroud leakage area, drill deck cross-sectional area, shroud height, collector-to-bailing airflow ratio, etc.) that have the most impact on respirable dust control, development of a dust collector inlet hood, development of a dust collector dump point shroud, and testing of a small diameter water separating sub. This paper summarizes the results of the aforementioned research that has been completed. Additionally, past dust control research for drilling operations of both underground and surface mines completed by the U.S. Bureau of Mines, created in 1910 and incorporated into NIOSH in 1997, is reviewed.

By A. A. Campoli

Retreat pillar mining concentrates stresses on workings directly outby gob areas, which can result in coal mine bumps. The development of bump-control design criteria by the U.S. Bureau of Mines was furthered by data from a novel bump control mining method at the Olga Mine, McDowell County, WY. The pillar splitting, retreat mining system induced large pillar pressure increases and roof-to-floor con-vergence. Roof-to-floor convergence monitoring proved to be a valuable tool in evaluating the pillar splitting mining method and localized destressing techniques. Maximum strain energy storage in chain pillars appears to have occurred just prior to the first of four split cuts. At that point a 15-ft-wide, highly fractured perimeter confined the core of the 55-by 70-ft pillars, permitting the pillar core to support tremendous pressures. Splitting the chain pillars into two 17.5-by 70-ft wings removed the confinement load, resulting in pillar yield. Thus, the pillar splitting mining method successfully redistributed the weight of the roof away from the pillar line. Shot fire and auger drilling destressing techniques aug-mented the pillar splitting mining method by redistributing the weight of the roof.

Jan 1, 1989

By Hillary W. St. Clair

Reaction rate coefficients were determined from analyses of the effluent gas for the reduction of granular ferrous oxide to metallic iron by passing carbon monoxide through a packed bed of oxide at a controlled rate in the temperature range 1,000° to 1,300° C. Coefficients were determined by the comparison of observed analyses and calculated analyses using a mathematical model that takes into account the nonuniform composition of both the solid oxide and the gas. A method is also given for finding the value of the rate coefficient that best fits the observed data.

Jan 1, 1968

By A. R. Taylor

Using solution calorimetry, the following heats of reaction were determined: (1) NaCN(c) + 1/Cu20(c) + 129H20(l) ? CuCN(c) + NaOH?128.5H2O ?H = -13.44±0.10 kcal/mole, (2) HCN(2) + NaOH?128.5H20 ? NaCN(c) + 129.5H20(l) ? = -2.52±0.02 kcal/mole. From these reactions, the heats of formation for CuCN(c) and HCN(2) were calculated to be 22.7±0.4 kcal/mole and 24.9±0.4 kcal/mole, respectively. Reaction 2 was made to check the consistency of literature values for heats of formation of HCN and NaCN. Adiabatic calorimetric measurements between 10° and 400° K showed the entropy and heat capacity of CuCN(c) to be 21.51±0.06 eu and 14.58±0.04 cal/mole deg, respectively, at 298° K. A broad anomaly in the heat capacity was found in the temperature range 285°-320° K. The heat of transition associated with this anomaly was less than 1 cal/mole, the sensitivity of the measurements.

Jan 1, 1971

[In selecting deposits of exploration projects, tabular deposits or large mineralized masses are favored because they may be explored systematically and because they afford the best opportunity for blocking out reserves in advance of mining, whereas irregular, small pipes and scattered]

Jan 1, 1941

[In selecting deposits for exploration projects, tabular deposits or large mineralized masses are favored because they may be explored systematically and because they afford the best opportunity for blocking out reserves in advance of mining whereas irregular, small pipes and scattered]

Jan 1, 1941

By Robert W. Freedman

Vacutainers are used by the Bureau of Mines and the Mining Enforcement and Safety Administration (MESA) for sampling mine air and products of combustion. Tests were conducted on both 10-ml and 30-ml sizes to study shelf life stability during storage, pretreatment of stoppers, and handling of a wider range of compounds. A chamber was constructed to provide convenient, efficient evacuation of the Vacutainers shortly prior to use. Fixed gases and C1 ?C5 hydrocarbons could be stored for 1 week or more after sampling. Where decreases occurred (C02 and C3-C5 hydrocarbons), they were predictable as a function of storage time. An unexplained phenomenon, slow accumulation of CO in evacuated Vacutainers, occurred after a few weeks of storage. The levels were low and time dependent. Attempts to eliminate this behavior by pretreating the stoppers were unsuccessful.

Jan 1, 1976

By D. B. Gawthrop, A. Taylor, G. St. J. Ferrott

"This paper presents data obtained as part of an investigation of the explosive properties of ammonium nitrate. During the course of the work: it was found desirable to investigate the sensitizing action of nitrostarch in mixtures of ammonium nitrate containing low percentages of this material. Data were derived as to the sensitivity to decomposition by heat and the completeness of detonation and,of detonation of straight ammonium nitrate, as compared with ammonium nitrate-nitrostrarch mixtures containing 1 to 10 per cent of nitrostarch.The ammonium nitrate was a sample of coated material obtained from the salvage of amatol shells. Its analysis was as follows:"

Feb 1, 1930

By N. L. Wimmler

"INRODUCTIONSedimentary deposits of titaniferrous magnetite occur at various localities in the eastern foothills of the Teton Ranse in Deer Lodge County, Mont. The Choteau deposit was examined by a Bureau of Mines engineer in August 1942. An exploration project was recommended.Core drilling exploration was begun in June 1945; it was concluded in August 1945, Seventy-six holes were drilled. This report presents the data obtained by the Bureau of Mines exploration.ACKNOWLEDGMENTIn its program of exploration of mineral, deposits, the Bureau of Mines has as its primary objective, the more effective utilization of our mineral resources to the end that they make the greatest possible contri¬bution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, Chief, conducts preliminary examination, performs the actual exploratory work, and prepares the final, report. The. Metallurgical Branch, R. G. Knickerbocker, Chief, analyzes samples and performs beneficiation tests. Both of these branches are under the supervision of Dr. R. S. Dean, Assistant-Director. The field work was supervised by Earshel W. Newman, engineer in charge of the Helena Field Office. D. B. Hoiekvam was the project engineer; he provided most of the data used in the preparation of this report."

Dec 1, 1946

By R. C. Annear

This report describes open, sublevel, and shrinkage stoping at the Greenwood mine, operated by Inland Steel-Co. The iron ore mine is in Marquette County, Mich., about 6 miles southwest of Ishpeming (fig. 1). The Greenwood is one of three active underground hard-ore mines on the Marquette range, the others being the Cliffs-Shaft and the Champion mines. The operation reflects an achievement in exploiting small, difficult-to-mine hard-ore bodies lying beneath a 200-foot overburden of glacial drift, which is partly water bearing. This report can indicate only briefly the efforts of personnel in overcoming adverse conditions in mining more than 2 million tons of ore, 80 percent of which was in lump form, for open-hearth production of steel. Significant data presented include descriptions of the principal mining methods employed, sublevel and shrinkage stoping; percent aged mining costs for the entire year 1957, covering both direct mining costs and general expenses; and performance records in units of labor, power, and supplies.

Jan 1, 1960

By M. Clair Smith

The Sweetwater, Castro, Trinidad, New London, and Hilltop chromite properties are situated within an area 8 miles long and 1 mile wide between San Luis Obispo city and Morro Creek, San Luis Obiso County, Calif. Development work at this group of mines was a part of a long-range project by the Bureau of Mines to develop strategic mineral reserves in the United States in accordance with the Strategic Minerals Act of 1939. The junior author of this report participated in the preliminary examinations made in 1941 of the chromite deposits that later in the same year were the subject of more intensive investigation under the immediate supervision of the senior author. The ore occurs in lenses and kidneys in masses of dunite contained in large poridetite areas. Production has boon in the form of lump ore and concentrates from disseminated ore. Work by the Bureau of Miner included surveying, mapping, trenching, sampling, and assaying. It is summarized separately in the text under the name of each mine investigated. The report gives a brief history of the district, describer the concentrating plant of the Castro Associates, and gives detailed results on sampling and assays at the various proportion.

Jan 1, 1951