Search Documents

By Garrett R. Hyde

Sintered yttria and sintered dysprosia can be used to make single-component thermistors having typical thermistor geometries and operable in the temperature range 500° to 1,200° C. However, at these temperatures, instability of platinum electrodes can contribute a slight aging effect if the thermistor is kept near 1,200° C for long periods. Typical characteristics at 500° C for an yttria disk thermistor 12 mm in diameter and 2 mm thick are a resistance of 12.4 megohms and a temperature coefficient of resistance of -3.8 percent per degree C. Typical characteristics at 500° C for a dysprosia thermistor of the same dimensions are a resistance of 1.84 kohms and a temperature coefficient of resistance of -1.6 percent per degree C.

Jan 1, 1970

By K. K. Kelley, L. B. Pankratz

The heat contents of four silicate minerals -- akermanite , cordierite , gehlenite , and merwinite --were measured from 298 ° to around 1,700 ° K by the dropping method . The results were compiled into tabular and equation forms suitable for thermodynamic calculations . The heat contents of these compounds are nearly additive with respect to their constituent oxides .

Jan 1, 1964

By D. H. Zellers

Since its inception the United States Bureau of Mines has fostered the development of portable mine lamps. Although there is still much to be desired with respect to illumination in coal and metal mines and the replacement of open lights has been slow the Bureau has been given credit for assisting materially in the development and introduction of the safe and efficient portable mine-lighting equipment available today. Much of the work conducted by the electrical section of the Bureau entails approval tests of various types of electrical equipment, including lamps; to be used in atmospheres that may contain methane or coal dust in explosive proportion. If a can lamp meets the requirements-for safety, efficiency, and adequacy, as published in Schedule 6B,4 it is approved and is generally known as a "permissible" lamp. The terms "approved" and '"permissible' often are used interchangeably. The manufacturer must put an approval plate on each approved lamp, showing it has mot the schedule requirements. The approval plate is not a guarantee that the lamp is safe. However, if the lamp, once in service, has not had any parts changed or improperly assembled or if carts that wear out or depreciate have been properly replaced it should still, be safe, efficient, and adequate for the service intended. Virtually all electric cap lamps in service today in the United States and a great many that have been sent to foreign countries bear the approval plate of the United States Bureau of Mines. Although many explosions have been attributed to open lights none has been charged against the permissible cap lamp. Nystagmus, a disease of the eye attributed to working under insufficient illumination, is practically unknown among; American miners, although it is quite prevalent among European miners.

Jan 1, 1935

By M. M. Fine

"INTRODUCTION One of the principal activities of the Bureau of Mines during the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydro-fluoric acid, such as the use of the anhydrous acid as a catalyst in high-octane-gasoline production and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorspar. 2/ In 1943 the consumption of acid-grade fluorspar was advancing at a more rapid rate than production and was only slightly less than production during the latter half of the year.The outlook for the postwar market for fluorspar is encouraging. Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid also are expected to increase under the impetus of war-initiated research. In consideration of these and other factors some authorities predict a new peacetime demand for fluorspar equal to 60 to 75 percent of the war production, 5/ 6/ and others believe that the fluorspar industry will be permanently expanded. 7/"

Dec 1, 1947

By Harry W. Campbell

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied parts of the 19,747-acre Lower John Day (OR-005-006) and 7,538-acre Thirtymile (OR-005-001) Wilderness Study Areas in order to evaluate their identified mineral resources. The study areas are located in Gilliam and Sherman Counties, OR, about 13 mi west of Condon. The area is underlain by the Miocene-age Columbia River Basalt Group. The Thirtymile study area is inferred to have 790,000 yd3 of subeconomic gold resources averaging 93.8 mg/yd3 gold ($1.21 yd3 at a gold price of $400 per oz) in two river bars. The Lower John Day study area has five river bars with gold occurrences totaling 1.0 million yd3 and averaging 13.5 mg/yd3 ($0.17 yd3) gold. A preliminary mining feasibility estimate suggests gold could be profitably mined in the study areas from placer deposits containing at least $3.83 yd3 in gold content. Stone, sand, and gravel occur in the study areas, but more accessible deposits are closer to regional markets. No mines or prospects are in or near the study areas; however, one lode mining claim, now abandoned, was located in the Thirtymile study area. Oil and gas leases cover both study areas.

Jan 1, 1987

The method of using large-diameter augers to recover coal was introduced to the mining industry about the end of World War II, and production of bituminous coal with augers has increased steadily to an estimated 7 million tons, or approximately 1.4 percent of the total mined in 1956. Although auger mining has proved to be a reliable and economical method of mining coal, a number of unfortunate fatal accidents have been experienced; consequently the need for these recommended safety standards is indicated for this comparatively new method of coal mining. As mining methods and equipment change from time to time and new hazards are introduced, these standards will be revised; therefore, questions or suggestions from the coal-mining industry will be welcomed and carefully considered.

Jan 1, 1958

By John E. Shelton

The growing interest in beryllium as a structural material, and its in-creased use in recent years for atomic energy application, have led both government and industry to express concern over the inadequacy of the beryllium resources in the United States and the free world. Contemplated and proposed uses for this unique material will surpass the capacity of the domestic beryllium mining industry to supply raw material, which is presently extracted from relatively small deposits by hand sorting. The need for a simple beneficiation process for beryl ores has long been recognized by the Bureau of Mines, but to date no single process has proved satisfactory for treating deposits containing a sufficient tonnage of beryl ore to warrant commercial exploitation. As a part of the Bureau's continuing effort to develop an economical recovery process, this report describes flotation research on samples of beryl-bearing pegmatites from the George Roebling mine in Connecticut, and the Colony mine in New Hampshire. The study resulted in two methods of treatment to which the ores responded reasonably well.

Jan 1, 1961

By S. L. May

The Bureau of Mines has developed several methods for extracting tantalum and columbium (niobium) and the rare-earth compounds from ores and concentrates. A cooperative agreement was made by the Bureau with Porter Bros. Corporation of Idaho to process 200 pounds of its euxenite concentrate by methods that had been developed at the Albany, Oreg., Metallurgy Research Center. The euxenite concentrate was processed to extract and purify the valuable metals by chlorination, solvent extraction, and hydrometallurgical techniques. Chlorination was used to convert the valuable constituents into chlorides and to partly separate them. Solvent extraction techniques were used to separate the tantalum from the columbium. The rare-earth and uranium compounds were purified by hydrometallurgical methods.

Jan 1, 1959

By Joseph A. Conway

This paper is one of a series dealing with the mining and crushing methods and costs of the nonmetallic industries, prepared under the sponsorship of and in cooperation with the U. S. Bureau of Mines,. The quarrying methods described in this paper are those used at the Monocacy trap rock quarry which annually produces from 450,000 to 500,000 tons of crushed stone. This property is located 3 miles east of Birdsboro at Monacacy, Pa., and is one of the three quarries operated by the John T. Dyer Quarry Co. Throughout the paper an effort is made to explain the various methods used and the cost of operation.

Jan 1, 1931

By Kathleen M. PH. D. Kowalski

This paper discusses human judgment and decision-making under stress. The authors review selected recent literature across various disciplines and suggest a definition of stress within the context of decision-making during the management of emergencies. They also discuss fieldwork by the Pittsburgh Research Laboratory, NIOSH, which explores traumatic incident stress, the relationship between previous training and performance under stressful conditions, and human behavior in underground mine fires. The authors assert that stress is one of the factors that decision-makers must contend with in most life-or-death situations. They suggest that a better understanding of individual's judgment and decision-making activities while under stress would yield a better understanding of how people reach the choices they make in emergencies. This enhanced understanding would be of enormous value to emergency managers, researchers, and policymakers.

Jan 1, 2008

By Ann G. Kim

Hydrocarbon gases, primarily methane but also the Ca through Cs paraffins, the Ca and C3 olefins and possibly the C4 and Cs olefins, are byproducts of coal formation. Although it is generally believed that coal formation occurred at temperatures below 200° C, most experimental work on gas formation from coal has been performed at temperatures between 200° and 1,000°C. The objective of this Bureau of Mines experiment was to determine if observable changes in the gases from coal could be produced at temperatures below 200° C in relatively short periods of time. The experiment involved heating coal samples from six coalbeds at constant temperatures and analyzing evolved gases. The composition of the gases at three temperatures was compared. At 35° C, over 99 pet of the gas is methane; at 125° and 150°, methane constitutes approximately half of the hydrocarbon gas. Isobutane and pentane are the predominant higher hydrocarbons at temperatures between 100° and 150° C.

Jan 1, 1974

A spectrographic procedure applicable to the semiquantitative determination of 29 elements in tungsten is presented. The method is designed to give estimates of impurity concentrations up to 500 p.p.m. Limits of detectability range from 0.3 p.p.m. for the more sensitive elements to 100 p.p.m. for the less sensitive ones. Tungsten metal samples varying in particle size from minus 300-to 30-mesh are excited in the presence of 5 percent germanium with a direct current arc. Germanium acts to stabilize the arc, minimizes the volatilization of tungsten, and serves as an efficient carrier to sweep impurities from the tungsten into the excitation zone. Curves are presented that show the volatilization behavior of germanium, tungsten, and impurities in tungsten at different concentration levels. Data obtained were used as guides in establishing the method of analysis. In the absence of established reliable analytical procedures for determining many impurities in tungsten in the parts per million concentration range, the spectrographic method described here should prove to be helpful in evaluating high-purity tungsten.

Jan 1, 1961

By R. E. Tremoureux

This paper describing the methods and costs of quarrying limestone at Sloan, Nev., is one of a series of similar papers being prepared for and published by the Bureau of Mines on this industry in the United States. These papers are designed to disseminate information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods Employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The quarrying operations at Sloan are interesting not only from a technical viewpoint and because of the magnitude of the deposit, but also because the quarry is located in a desert region far removed from the centers of population where lime is used. The quarry and plant are in Clark County, Nev., 20 miles west of Las Vegas, which is the nearest town to the site of the Boulder Canyon Dam. Sloan is on the main line of the Union Pacific Railroad connecting Salt Lke City and Los Angeles. The latter city is 280 miles from Sloan and it is the shipping, point for all supplies.

Jan 1, 1932

By V. M. Benson

A simplified, routine method for determining lithium in lithium-bearing rock is presented. The sample is decomposed by repeated treatments with nitric, hydrofluoric, and perchloric acids. Since this procedure does not appreciably dissolve beryl, interference by beryllium (the principal interfering cation) is minimized for most samples. The salts are brought into solution with water and enough citric acid-ammonium citrate buffer is added to make the final volumetric dilution 0.20 M with respect to citrate. The addition of citrate greatly reduces anion interference in the hydrogen-oxygen flame, slightly increases the intensity of the lithium 671 millimicron emission line, and reduces the effect of most of the interfering cations to the extent that analytical separations are not necessary. The accuracy of results of single determinations of lithium in a pegmatite containing spodumene, lithium-bearing mica, and beryl are approximately equal to that obtained by other flame methods, INTRODUCTION This investigation was undertaken in Bureau of Mines laboratories to develop a reliable, rapid, routine analytical method for determining lithium in lithium-bearing minerals. The requirements of the procedure were that the method should be applicable to the analysis of a variety of lithium-bearing ores and test products, and the results would be reasonably accurate for materials containing 0.05 to 8 percent Li20.

Jan 1, 1961

By F. S. Crawford

Interesting data on electric blasting and sinking of the Montreal No. 5 shaft of the Montreal Mining Co., Montreal, Wis., were obtained during the sinking of the last 877 feet of this shaft. Several unusual features and safety practices are also to be found in the Montreal mine. The Montreal shaft was sunk 2,156 feet from August 16, 1921, to May 1, 1924, and 877 feet from October, 1927, to June, 1928. The first section of the shaft was supported with steel sets spaced 5 feet on centers; and instead of lagging the walls were covered with three-eighths of an inch of gunite where Greenstone was encountered, and where quartz-slate was found (from the surface to the 12th level) the walls were lagged with tamarack lath treated with carbolineum, a preservative.

Jan 1, 1929

By W. L. Schmidt

The effect of a water-repellent film in sandstone cores on the effective permeability-saturation relationship was investigated as part of a cooperative research program between the Bureau of Mines and the American Gas Association. The repellent film was formed by the reaction of methyltrichlorosilane3 with the connate water in the core. Other researchers have reported on the use of silicone chemicals to alter the flow characteristics of porous media (1-3, 5-7, 9, 10).4 The previous studies, however, dealt almost entirely with oil-water or oil-gas systems and not with water-gas systems. The primary purpose of this study was to determine the feasibility of using silane to retard the influx of water into natural-gas storage wells and to determine the necessary requirements for achieving this result. The success or failure of silane treatment as a remedial measure depends on its effect on gas-production rate and attendant water production.

Jan 1, 1961

By S. H. Ash

The paramount responsibility of Government is to protect the general welfare. One of the chief functions of the Bureau of Mines is to investigate and publicize methods of increasing safety and efficiency in mining operations. In an industrial civilization, energy resources constitute the foundation of a sound economic structure (14).4/ Coal is only one source of energy, but it provides more than half the energy consumed in the United States.

Jan 1, 1946

By E. P. Youngman

The mining law now in force in Finland is the Imperial Russian Ukase of 1883, promulgated November 12, 1883, by Czar Alexander III, with the sanc- tion and permission of the Finnish Estates. This law repealed prior legisla- tion, as follows: Crdinance of liay 25, 1857, concerning the appropriation of ores and minerals; as wall as the right to remove and utilize them; proclama- tion of January 20, 1868, amending, the ordinance of May 25, 1857; proclama- tion of October 3, 1621, concerning the appropriation of precious metals; and the proclamation of October 30, 1878, concerning prospecting for gold, etc., in Finnish Lapland. A proposal for a new mining lar is still being considered by the Finnish Diet. This new law, if and when promulgated, will differ only slightly from the law of 1683 but will be drafted in more modern language."

Jun 1, 1932

By Sara J. Davenport

Hydrogen sulfite has been listed (1)3/ as a possible hazard in 50 occupations, many of which are in the mineral industries. The effects of its occurrence in the petroleum industry made themselves felt more than two decades ago, resulting in a comprehensive study (2) of the toxic gases from Mexican and other high-sulfur petroleum products. The mining industry, likewise, has had cause to guard against this gas. Enough hydrogen sulfide has been found in coal and some noncoal mines during normal operations to cause severe eye irritation, some serious illness, end even fatalities. It is usually a product of the decomposition of sulfur compounds and may be produced by burning explosives containing sulfur; the gas in harmful qauntities is formed by the use of block blasting powder or by the use of dynamite in blasting sulfide ores. Hydrogen sulfide is readily soluble in water, and enough may be released from water streams in coal and noncoal mining to cause fatal poisoning it is found sometimes in stagnant water underground, particularly where ventilation currents are absent, and great care must be exercised when accumulations of such waters are disturbed, as exposure to comparatively low concentrations of the gas evolved therefrom has caused fatal accidents.

Jan 1, 1945

By E. A. Pelczarski

Initially, the objective of this contract was to develop a PWSCSR that could meet proposed criteria (that were different from 30 CFR 11(Title 30 of the Code of Federal Regulation part II) and that would be less than twice the size and weight of a filter self rescuer. This objective was met. Consequently, the original contract was extended to develop a PWSCSR that would meet existing CFR-30 criteria within the same size and weight constraints. This resulted in the development of a PWSCSR (the SR-100) that received NIOSH/MSHA approval (TC-239). This report presents a historical discussion of the design and development of the SR-100 as developed by CSE Corporation under Bureau of Mines contract number H0368013. The technical parameters and the test results of NIOSH/MSHA 30 CFR 11 certification are also presented.

Jan 1, 1990