Search Documents

By K. Kar, A. Sreeoath, M. Gautam

"This paper presents results of an experimental investigation of the sampling efficiency of a blunt cylindrical sampler oriented with respect to the oncoming flow. The number of particles sampled by the cylindrical blunt sampler and an isokinetic sampler is measured using the TSI Aerodynamic Particle Sizer. A technique is described to conven the ratio of the particles sampled into the sampling efficiency. The experimental data thus obtained is then compared with the impaction model of Vincent and Mark (1982) with the empirical constant determined from our experiment.. The comparison shows excellent agreement for 0° and 90° orientation.1.0 IntroductionCylindrical dust samplers are widely used in practice to determine the concentration of the airborne particulate matter. The sampler is simply a means to collect particles from the ambient, whose concentration is subsequently measured by some size selective techniques. Gravimetric and optical techniques are the two most commonly used methods to measure the particle sizes. While impactors are used in gravimetric analysis, Aerodynamic Particle Sizer, Aerosizer. Electron microscope, Coulter Counter etc. use the optical method to measure the particle sizes. The Aerodynamic Particle Sizer (APS) and the Aerosizer are the new generation devices which employ the time of flight of particles within intersecting laser beams to determine the particle size.The introduction of the sampler in the free stream disturbs the flow pattern due to two distinct actions of the sampler on the fluid stream: one of them results due to the conformity of the flow to the geometry of the circular cylinder and the second one is caused by the flow into the suction orifice. If the sampler performance is determined by the number of particles entering into the sampler inlet relative to the number of particles present in the free stream, then the particle trajectory outside the sampler and into the inlet is the deterministic factor for the sampling efficiency. The particle trajectory inside the sampler is not important in this case."

Nov 1, 1995

The object of this program was to extend the capabilities of visual paging systems both in size and function. The system developed uses the mine pager phone line for communication, monitoring, and remote control. A central station, using a minicomputer, transmits signals by phase inversion modulation of a 16,384 Hz carrier to as many as 999 remote units. The remote unit addressed returns An echo to indicate that it is functioning and, in the case of monitor units, to convey the monitor data. Magnetically latched display dis[c]s, which can be seen from both sides when posted, are used for visual paging. Lists of the addresses of posted pages, unanswered pages, and non-echoing units are prepared by the central station computer. The system was designed to be intrinsically safe and should operate for three months on a 12-volt lantern battery.

Jan 1, 1980

By R. E. Lindstrom

Electrooxidation techniques were investigated on a bench scale by the Bureau of Mines to determine the applicability of the process for extracting molybdenum and rhenium from low-grade molybdenite concentrates. Parameters affecting the extraction, such as pulp density, power consumption, reagent requirements for pH control, and electrolytic cell configuration, were studied. Molybdenum and rhenium extractions of 98 to 99 percent were achieved from several concentrates containing 4.76 to 28.6 percent molybdenum and 180 ppm to 1,000 ppm rhenium. Optimum results were obtained by maintaining pH values between 5.5 and 7.0 during electrolysis and allowing the final pH to rise to about 8.2. Reagent consumption was 4 to 6 pounds of sodium carbonate per pound of molybdenum extracted. The power consumption declined from a range of 12 to 25 kilowatt hours per pound of molybdenum extracted with immersion electrodes to 9.7 kilowatt hours with a bipolar flow-through cell; however, molybdenum extraction was independent of cell configuration.

Jan 1, 1973

By R. S. Warfield

Following World War II, the rapid increase in both military and civilian activity in the area served by the Alaska Railroad stimulated interest in the availability of local sources of nonmetallic minerals that might be used for building materials. Except for abundant sand and gravel and some pumice, the construction industry of the area depended entirely on high-cost imports for building materials of mineral origin. Because continued rapid growth was anticipated, development and use of local sources of such materials was advocated by both military and civil authorities to reduce the high costs of con¬struction and bolster the unstable economy of the area. The U.S. Department of the Interior began a program On included examining the numerous deposits of nonmetallic minerals accessible to the Alaska Railroad to determine their possible use as raw materials for the construction industry. Preliminary field investigations were made by the Geological Survey. The more promising deposits were subsequently examined and sampled by Bureau of Mines engineers, and the samples were subjected to the laboratory tests necessary to indicate the chemical and physical characteristics of the raw materials or their products. Such field and laboratory investigations were conducted on clay, shale, argillite, limestone, gypsum, and pumice taken from various parts of the area. In initial phasees of the work, done irate 1948 through 1952, many of the deposits examined were suitable for proctoring building materials. Results of the work completed during that period have been published in a Bureau of Mines report3 giving general information and detailed data on more than 35 deposits that were investigated.

Jan 1, 1962

By Edmund S. Leaver

The Precious Metals Section is concerned primarily with ore-testing problems associated with precious metals and with the analysis and concentration of a large number of the strategic-mineral samples that have been included in the research program of the Bureau of Mines. During the fiscal year 1938-39, 30 projects were completed. The requests for this service are based upon the desire f the sponsor to obtain the best or most satisfactory method for maximum recovery of the minerals. In many instances it is a question of improving present milling practice, with due regard to utilization of present equipment. In others, the probable tonnage available maybe the deciding factor in the choice of a particular recovery method. Under all circumstances the results of tests axe prepared with the thought of aiding a competent metallurgist, familiar with local conditions, to formulate a practical flow sheet or to assist the mill operator to correct known losses. A microscopic examination for identification of the mineral constituents and their association in each ore is always a big help, in planning the tests and may indicate the reason for former troubles or assist with best procedure.

Jan 1, 1940

By Edmund S. Leaver

The Precious Metals Section is concerned primarily with ore-testing problems associated with precious metals and with the analysis and concentration of a large number of the strategic-mineral samples that have been included in the research program of the Bureau of Mines. During the fiscal year 1938-39, 30 projects were completed. The requests for this service are based upon the desire of the sponsor to obtain the best or most satisfactory method for maximum recovery of the minerals. In many instances it is a question of improving present milling practice, with due regard to utilization of present equipment. In others, the probable tonnage available maybe the deciding factor in the choice of a particular recovery method. Under all circumstances the results of tests axe prepared with the thought of aiding a competent metallurgist, familiar with local conditions, to formulate a practical flow sheet or to assist the mill operator to correct known losses. A microscopic examination for identification of the mineral constituents and their association in each ore is always a big help, in planning the tests and may indicate the reason for former troubles or assist with best procedure.

Jan 1, 1940

By Richard O. Kneisley

An empirical method, based on U. S. Bureau of Mines field studies in several Western U.S. coal mines, is presented for sizing gate road yield pillars. Discriminant analysis was used to generate functions separating successful from unsuccessful case studies. These functions relate the pillar width-height and extraction ratios and a pillar development factor to the Coal Mine Roof Rating System (CMRR), and are assumed to establish three criteria that other entry systems, under similar conditions, must satisfy. A program, Pillar Sizer, from user-provided inputs, generates a range of pillar sizes that meets the proposed criteria. Although the analysis is based on a sample consisting primarily of two-entry systems, the derived expressions generate pillar sizes closely agreeing with observed, two-entry and three-entry in situ pillars. It is concluded that the proposed approach should assist mine operators estimate entry system yield pillar dimensions.

Jan 1, 2010

By Stephen Gerard Sawyer

A Fortran IV computer program entitled WAVE, which employs an explicit finite difference scheme for solving the one-dimensional wave equation for a time-dependent inelastic rock has been developed. The viscoelastic properties of the rock are represented in terms of a generalized Voigt model. The theory on which the computer program is based is rederived and a short description of the program is given. The computer program input instructions, a listing of the computer program, and example problems with required input and subsequent printed output are presented in appendixes. In the example problems) calculated results are free of spurious oscillations which occur in certain other methods of numerical calculation) notably the extended Ritz method.

Jan 1, 1972

By J. P. Powell

This report provides information on the techniques and results obtained on representative waterflooding projects in Cowley County, Kans. Records show that waterflooding was begun as early as 1935, but not until 1948 was the method expanded. The greater depths to the oil-producing formations in this area compared to those in eastern Kansas undoubtedly delayed the widespread use of secondary-recovery methods. This report presents a discussion of four waterflooding projects in Cowley County, Kans. The locations of these projects are shown in figure 1. The projects have been in operation from 1 to 7 years and have produced more than 1 million barrels of additional oil by injecting 11.5 million barrels of water. The projects are designed to take advantage of elevation and height of the separator tank to collect by gravity flow the produced brine at the respective treating or storage tanks. The closed-type water system is used on three of the projects and an open-type water conditioning system on the fourth. On one of the projects, which was drilled along a narrow shoestring formation, alternate well, were converted to input wells. However, most of the input wells for flooding converted producing wells.

Jan 1, 1958

By W. T. Benson

The Bureau of Mines has examined selected deposits of titanium minerals throughout the United States. The titaniferous magnetite deposits in the western San Gabriel Mountains, Los Angeles County, Calif., were among those selected for study, and in 1956-58 field work was conducted to determine the extent and character of the titaniferous magnetite deposits occurring in the area. This report describes this work and summarizes earlier work in the area by the Bureau and others. The titaniferous magnetite occurs disseminated as seams and lenticular pods in an anorthosite belt 4 to 6 miles wide that trends about. N. 80° W., extending from sec. 13, T. 3 N., R. 12 W., to the west boundary of R. 14 W., at which point the titaniferous magnetite-bearing rocks disappear beneath the sediments in the Santa Clara River Valley.

Jan 1, 1962

By M. S. Seehra, V. S. Babu, L. Farinash

"The diesel particulate matter (DPM), a constituent of the diesel engine exhausts, is known to be a potential carcinogen. 1- 3 Consequently, suitable methods to control/eliminate DPM have ·been under investigation in recent years. The DPM can be controlled by using fibrous ceramic traps. However, clogging of traps by DPM requires the impractical periodic trap replacement. Following the recent work by Garner and Dent,4,5 we are investigating the in situ use of microwaves to regenerate the ceramic traps, thereby eliminating the trap replacement step in this process. The use of microwaves instead of conventional heating for trap regeneration has the advantage of selective heating of the DPM instead of the trap, if the trap absorbs insignificant microwave power relative to the DPM. Also, the oxidation characteristics of the DPM are needed to understand fully this regeneration process.The rate of energy absorption P per unit volume of a sample is given byP = wE"" |Eo|2 • (1 )where w is the angular frequency, |E0|2 is the intensity of the microwave radiation, and E” is the imaginary part of the dielectric constant (E = E’ + iE”) . Thus measurements of E11 for DPM and ceramic trap material are needed to determine their capacities for microwave absorption. In this paper, we report these measurements carried out at · a frequency of 8.7 GHz. Following microwave absorption, the DPM is expected to oxidize. The oxidation characteristics of the DPM have been investigated using Fourier transform infrared (FTIR) spectroscopy of the evolved gases CO2 and CO and using thermogravimetric analysis (TGA). Finally, some information on the structure of carbon in DPM has emerged from the analysis of its x-ray diffraction spectra. Results of these experiments are reported in the following pages."

Dec 1, 1996

By T. H. Miller

This piper is a continuation of a series of yearly review articles started in 1925 by Thomas Varley. The development of flotation has been rapid, and better understanding of the functions o' flotation reagents has resulted in many changes in the kinds and quantities o reagents used. It is the purpose of this report to present the information in such a manner as to be of value to the milling industry as well as to the manufacturer of flotation reagents. These data have been compiled from a. survey of approximately 250 flotation plants of all classes within the United States. Many of these plants made complete reports of their operations, out others were apparently unable to supply this information in sufficient detail to meet the requirements of this investigation. Although it is realized that the data obtained in this survey are not as full as they should be to render the greatest service possible to the milling industry, it is hoped that succeeding articles will include complete information regarding milling; conditions and recoveries. As in the past, every effort has been made to conceal individual plant operations. RESULTS OF INVESTIGATION Table 1 gives the tons of ore treated by gravity and flotation methods and the concentrates produced as reported by 208 plants. The totals of 77,043,535 tons of ore and 4, 596,640 tons of concentrates from this table compare with totals of 78,973,012 tons and 4,683,972 tons respectively (furnished by the Bureau of Mines, Division of Mineral Statistics), indicating that the milling survey is about 98 per cant complete.

Jan 1, 1930

By Fred N. Kissell

A parachute-type stopping intended for changing the course of mine ventilation air during mine emergencies has been designed and tested. Some production uses are also visualized for metal mines. Preliminary tests in the laboratory and underground indicate that the parachute stopping is a workable concept, but further developmental research is required.

Jan 1, 1975

By M. Howard Berliner

In August 1943 the Bureau of Mines completed seven churn-drill holes in an area of old mine workings near Linden, Wis., formerly known as the Argall mine. The work was undertaken as part of a general investigation by the Bureau of the zinc and lead producing area of southwestern Wisconsin at a time when special effort was being made to increase the production of metals necessary for war. The area was selected for investigation on the basis of its favorable geologic structure, past history, and apparent mineralization.

Jan 1, 1948

By J. H. Jacobs

The first authorization, in November 1940, was for a plant of only several hundred pounds capacity at Boulder City, Nev. Improvements in the process and subsequent additions to some sections have enabled the plant to produce more than 2,000 pounds of manganese per day for substantial periods. By the time pilot-plant operations were suspended in June 1945, over 1,500,000 pounds of metal had been produced. The future of electrolytic manganese production obviously depends not only on satisfactory development of methods but on availability of raw material and demonstration of valuable uses. Investigations of manganese-ore deposits in this country, made since 1938 by the Bureau of Mines, have revealed large amounts of ore suitable for making electrolytic manganese. At first the pilot plant was operated on ore from the Three Kids mine near Las Vegas, Nev. After practical features of the process had been worked out, other ores from throughout the United States were tested in the pilot plant. The purpose of this paper is to compare the results obtained on the following ores: Three Kids; Ladd mine, Tracy, Calif.; Chamberlain, S. Dak., nodules; and ore from Metals Reserve stockpiles at Deming, N. Mex.; Cushman, Ark.; and Philipsburg, Mont.

Dec 1, 1947

By L. F. Willmott

The production operation of a Kerpely gas producer at Louisiana, Mo., is described. This unit, originally designed for airblown operation was modified to permit using oxygen in the blast in place of air. The first runs J for test purposes, were made in June 1950. After this, seven production runs were made and these are the subject of this report. Total gasification time was 245 days. In each run, Nut or Pea coke or mixtures of both at a rate varying from 1,700 to 2,300 pounds per hour was converted with oxygen and saturated steam to produce synthesis gas - primarily carbon monoxide and hydrogen -approximating a predetermined rate of 80,000 to 95,000 cu. ft. per hour and a predetermined hydrogen-carbon monoxide ratio, The requirements per 1,000 std. cu. ft. of (CO + H2) were 21.6 to 30 pounds of coke, 213 to 267 std. cu. ft. of oxygen, and 3L4 to 47.B pounds of steam.

Jan 1, 1955

By E. L. Litchfield

Descriptions are given of the techniques and apparatus used by the Bureau of Mines for determinations of flat plate ignition quenching distance and minimum spark ignition energy. The descriptions include discussions of reaction vessel materials, shapes, and sizes and discussions of electrode configurations. Spherical, hemispherical, or flat plate electrodes are recommended. The preferred metal in electrodes and electrode supports is stainless steel; the flat plate electrodes incorporate flanges of low electrical conductivity which are most frequently formed from glass. Various aspects of the electrical energy supply system are discussed and suitable arrangements of components are indicated. The concept of a thermal relaxation time is introduced as a basis for the choice of a minimum interspark time during the testing of a gas mixture. The following indicate the varied conditions under which these tech were utilized: Mixture pressures between 10 mm Hg and 45 psig, initial temperatures between -78° and +198° C, and gaseous mixtures representing wide ranges of cL.. D reactivity and corrosiveness. Minimum ignition energies were determined which varied from about 10-7 joule to nearly 103 joule.

Jan 1, 1967

By John A. Breslin

Size distributions and concentrations of particulates emitted from diesel engine exhausts were measured with cascade impactors. Samples were taken from the exhaust of two types of engines using three types of fuel and operating under five different engine speed and load conditions. The measured mass median diameters of the diesel particulates were typically about 0.3 um. There was no significant difference in mass median diameter between engines or fuels and only a slight dependence on operating mode. Concentration measurements ranged from 14.2 to 250.9 mg/cu m, and calculated mass outputs, from 64 to 10,000 mg/min. Significant differences in mass output were found between engines, fuels, and especially between different operating modes. The quantity of clean dilution air that would be required to reduce the particulate mass concentration below the 2.0 mg/cu m respirable dust standard for coal mines was greater than the dilution air required to meet the standards for noxious gases for both engines tested.

Jan 1, 1976

Prevention of coal-mine explosions depends largely upon thorough knowledge of the causes that initiate explosions. A review of coal-mine explosions in one geographical area when supplemented by nationwide data of similar nature, should serve as a guide for the adoption of measures for explosion prevention. Explosions in bituminous-coal mines of the United States during the 10 years ended December 31, 1932, ranked third in the causes of fatal accidents and constituted 16.1 percent of all fatal accidents in bituminous mines. Kentucky now ranks fourth in coal output in the coal-producing States of this country; a study of the coal-mine explosions in this state will be of definite interest locally among coal-mining people, as well as to those in the coal-mining industry who are concerned in preventing coal-mine explosions. This circular reviews gas and dust explosions in Kentucky coal mines to show their hazards, to point out the influence of certain factors in causing explosions, and to indicate the effectiveness of preventive measures.

Jan 1, 1934

By Dougherty. E. Y., S. W. Zoldok, John W. Cole

"INTRODUCTION During its wartime program of exploration for minerals essential to the national economy, the Bureau of Mines was instructed to investigate sources of raw materials used in the manufacture of iron and steel. As a part of this investigation, some work was done on the iron deposits on the Neutral and Aztec claims on Buckhorn Mountain Canogan County, Washington, which was designed chiefly to indicate the nature and behavior of the ore deposits below the surface exposures. Diamond drilling was started in June and completed in July 1945. Preliminary laboratory tests on iron, ore from Buckhorn Mountain were completed during the fall and winter of 1945. This report presents the data obtained from the investigation.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final re¬port. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Apr 1, 1947