Search Documents

By Chas. G. Maier

The bright annealing of copper is an industrial practice of considerable importance. In connection with this process, equilibrium concentrations of carbon monoxide and dioxide, which may exist in contact with copper and cuprous oxide at elevated temperatures, are of interest. Data obtained at the Pacific Experiment Station of the U. S. Bureau of Mines enable estimates of these equilibrium concentrations to be made in two independent ways. Although the publication of final data on one method can not take place until certain further experimental work is accomplished, repeated requests which the Bureau of Minus has had for data relative to the annealing and deoxidation of copper justify the present preliminary report. This paper deals with the calculation of gas concentrations in the reduction of cuprous oxide, using more scientific data which will be published later, and refers especially to those conditions of temperature and concentration of practical implication, and from which critical limits ensue.

Jan 1, 1929

By C. G. Kirkpatrick

Analysis of the data produced by a wide-band, sensitive, horizontal, biaxial motion sensor has revealed several distinctive patterns before, during, and after a roof fall. The signals prior to the roof fall are similar in spectra, but one thousand times larger in amplitude, than those after the roof fall. Immediately preceding the roof fall, by two to twelve hours, five events occurred which were larger in amplitude and lower in frequency than even the large pre-roof fall background signals. An interpretation of these events is offered.

Jan 1, 1979

By V. E. Edlund

Laboratory batch flotation tests were conducted on copper converter slags to evaluate the relative merits of recovering copper from slow-cooled versus water-quenched slags. Three slags containing 1.6, 5.0, and 6.6 percent copper were used. More than 90 percent of the copper was recovered in a rougher concentrate leaving a 0.2- to 0.3-percent copper tailings when treating slow-cooled slag. Lower recoveries and higher copper tailings ranging from 0.5 to 0.6 percent copper were obtained from quenched slag. Grindability studies were made on the respective heat-treated slags. Quenched slags proved more difficult to grind than slow-cooled slags. Cost studies showed that quenched slags can be treated at slightly lower cost than slow-cooled slags. However, the cost advantage of processing quenched slags is more than offset by the higher copper recoveries obtained from slow-cooled slags.

Jan 1, 1971

By B. A. Rogers

The problem of obtaining enough manganese for use in the manufacture of steel appears likely to recur when international relationships are disturbed and to become serious at any time when the United States is cut off from its customary supply. Some idea of the problems that an e under war conditions may be obtained from a description given by Ellicott3/ in 1918 before the American Iron and Steel Institute. This condition arises because in normal times there is an economic advantage in importing available high-grade foreign ores to the neglect of our own less satisfactory resources. That considerable low-grade manganese ore and a much smaller amount of high-grade material are available in this country is well known from geological surveys 4/ and has been confirmed by Bureau of Mines investigations. Locations of the various deposits are indicated in figure 1. The possibility of greatly expanding domestic production was actually demonstrated from 1913 to 1918, when the annual production of manganese from domestic ores rose from about 4 percent to approximately 35 percent 6/7/ of the total consumption of ferromanganese and spiegeleisen. In idea of how domestic production compares with total consumption in the United States can be obtained 1 from figure 2, taken from the Minerals Yearbook8/ for 1970. Assuming that it is possible to increase production of manganese ores sufficiently to supply all our needs, such a program presumably would require 2 or 3 years, and the cost of production would certainly rice considerably, for some time at least. For

Jan 1, 1941

By James H. Gary

Data regarding the composition and physical properties of Florida land-pebble phosphate-waste slime are presented, and the feasibility of dewatering and beneficiating the slime by several different methods is discussed. Chemical analyses, electron micrographs, and X-ray diffraction data showed that principal constituents of the slime included quartz, attapulgite, and flaorapatite. Viscosity of the slime changed with pH; thixotropic, Newtonian, and rheopectic states were observed as the pH increased. Use of various flocculating agents was not effective in improving thickening properties of the slime. Dewatering tests using pressure filtration showed that temperature influenced the filtration rate more than pressure; the filtration rate at 165° C was tenfold that at room temperature. Selective flotation of the slime, using two different processes, gave promising results. About 25 pct of the phosphate was recovered in a concentrate assaying 31 pct P205, Other tests demonstrated that the slime could be successfully fractionated at 20-microns using a hydrocyclone. In hydrometallurgical tests about 80 pct of the phosphorus and alumina were chemically extracted from the slime using sulfuric acid. Limited bacteriological studies made of the slime showed that several types of microorganisms were present and grew in the material despite the presence of fluorine-bearing minerals.

Jan 1, 1963

By Carl Belser

In 1925 the Park Utah Consolidated Mines Co., after several years of experimental work, installed a system for signalling from cages which has been operating efficiently and with low upkeep costs for the post 19 years. The system was adopted for a large western metal mine but was later abandoned be arse of the constantly shifting shaft alinement. Recently the system has been studied and probably will be put into service at two other large mines. One of the principal reasons wry the system has not boon adopted more widely has been the lack of adequate details both as to the desirability of having such a system and as to its construction and operation. Previous signaling, systems contained undesirable features, such as charged bare wires extending the full length of the shaft. Under the direction of O. N. Friendly, then general superintendent of the Judge Mining & Smelting Co., the present system, entailing the use of a samll current at low voltage, was gradually developed. Many of the refinements in the system wore contributed by Leonard Wilson, consulting electrical engineer, Salt Lake City, Utah.

Jan 1, 1945

By E. G. King

Strontium sulfide and barium sulfide occur as intermediates in commercial treatments of the impure natural sulfates to produce pure strontium and barium chemicals. Thermodynamic considerations involving these sulfides have been hampered by lack of basic data, such as the entropies at 298.15°K. This paper reports the results of heat capacity measurements of strontium sulfide and barium sulfide in the temperature range 50°-298°K. The entropies at 298.15°K. were derived from the heat capacity values. Free energies of formation at 298.15°k. were computed from the entropies and literature values of the heats of formation. Strontium sulfide and barium sulfide are thermo-dynamically less stable than calcium sulfide, but more stable than magnesium sulfide.

Jan 1, 1960

By A. L. Engel

This investigation was undertaken to assess the feasibility of processing an extensive deposit of iron ore near Palisades, Eureka County, Nev., previously penalized for high phosphorus content. The experiments described indicate a satisfactory accomplishment of objective. Chemical treatment will permit a high-phosphorus iron ore to be used. Leaching with acid solution effectively lowers the phosphorus content with a [gligible] loss of iron. The use of hydrochloric acid is preferred because [ ] does not contaminate the ore and the cost is lower. Minus-1/2-inch ore was satisfactorily leached in 24 hours, minus-1/4-inch ore, in 8 hours, and minus-10-mesh ore, in 3 hours. About 40 pounds of acid per ton of ore was consumed in each instance.

Jan 1, 1959

By Kenneth M. Smith

The kaolin deposits of Aiken County, South Carolina (fig. 1), have been worked continuously since 1852. It has been long known that the deposits contain a high percentage of' alumina and that large reserves exist. These facts led to the early selection of' this area for examination in the search by the Bureau of Mines for high-alumina clays. An exploratory program was started by the Bureau, and drilling was carried on from. June 27, 1942, to October 31, 1942. The kaolin-bearing district occupies an area approximately 25 miles long and 11 miles wide, running northeast, with its center at Aiken, S. C. (fig. 1). Within this district, a triangular area bounded by Horse Creek, Silver Bluff Road, and Hamburg Road was roughly prospected by boring 43 machine and 12 hand holes. As a result of the data obtained, a final smaller area was chosen for more systematic prospecting. This area is bounded by Pine Log, Tewkesbury, Silver Bluff, and Craig Sawmill Roads and covers about 4,000 acres. Mineral exploration agreements covering 11,272 acres were signed by 35 property owners, and 11,956 feet was drilled in 200 holes on these properties.

Jan 1, 1949

By J. Hudy

An investigation has been made to determine the applicability of the Cendrex3 X-ray instrument for the measurement of the ash content of washed bituminous coal products. The results obtained for selected products from six preparation plants in the Appalachian region and one preparation plant in the mid-western region are described. Emphasis of the study was placed on low-ash bituminous coal products suitable for utility or metallurgical markets. There was good agreement between the results obtained by conventional ash determination methods and by ash determination using the Cendrex for all products tested.

Jan 1, 1968

By L. C. IlsLey

A list of permissible mine equipment, tested and approved p or to July 1, 1934, was published in Bureau of Mines Information Circular 6813/. The present list4/ includes virtually all the electric air compressors, coal drills, mining machines, loading machines, conveyors, mine pumps, room hoists, mine telephones, rock-dusting machines, switches, electric cap lamps, flame safety lanes, electric hand and trip lamps, electric flood lamps, methane detectors, blasting units, storage-battery locomotives, tandem locomotives, mower trucks, and concrete mixers tested and approved by the Bureau to January 1, 1937. The system under which these devices were tested permits the manufacturer, after his equipment has passed certain tests prescribed by the United States Bureau of Mines, to mark his equipment with a seal showing that it has been approved by the Bureau. These tests are designed to insure that equipments have the minimum requirements for safety in use. The only object of the bureau in making such tests and publishing lists of permissible equipment is to help decrease the hazards of mining.

Jan 1, 1937

By Michael P. Moore, Christopher J. Rise

"Over the past twenty years, there have been numerous studies which have attempted to correlate the prevalence of Coal Workers' Pneumoconiosis (CWP) with different characteristics of the coal seam. Some investigators have tried to find a relationship, or the lack of a relationship, between the rank of coal seams and the incidence of CWP. Others have attempted to show that there is a positive correlation between the mean mass of respirable dust in the mine atmosphere and the prevalence of CWP. Still others have tried to determine the influence of the quartz content of respirable dust on the incidence of CWP. Unfortunately, many of these different investigations have conflicting conclusions.One area of research with conflicting conclusions deals with the relationship between the rank of the coal and the incidence of CWP. For example, an inves¬tigation conducted in Pennsylvania and West Virginia coal mines concluded that the prevalence of CWP increases with an increase in coal rank (1). A study in Great Britain also observed a close relationship between the rank of coal and the prevalence of CWP (2). However, another study involving 312 Appalachian coal miners concluded that the association between coal rank and CWP might be fortuitous and that other factors may be more important (3). In addition, an investigation involving 2,600 miners during a period of twenty years in Great Britain established that there is only a weak correlation between the prevalence of CWP and the rank of the coal (4). Consequently, it appears that there is still uncertainty as to whether or not the rank of the coal seam has an influence on the development of CWP.Another area of investigation concerns the relationship between the mean mass of respirable dust present in the mine atmosphere and the prevalence of CWP. A study involving 4,122 miners over a period of ten years in Great Britain noted a high correlation between the mean mass of respirable dust and the incidence of CWP (5). Another investigation involving 3,154 British face workers con¬cluded that the overall mass of respirable dust is the factor most closely related to the ten-year attack rate of CWP (6). However, a study conducted in thirty-one mines in the United States concluded that it is doubtful that the quantity of respirable dust alone is responsible for the difference in the prevalence of CWP (7). Even though there are conflicting conclusions, there are many more investigators who confirm, rather than deny, the relationship between the mean mass of respirable dust and the development of CWP.The third subject of investigation is the role of quartz in the incidence of CWP. For example, two studies in Great Britain concluded that the quartz content in coal mine dust has no relationship to the prevalence of CWP (8,9). But a study involving 312 Appalachian coal miners revealed that the level of exposure to free silica plays an important role in the development of CWP (10). Once again, the conclusions reached by different researchers are conflicting.Probably the most important factor in the discrepancy among the studies is the variability among different coal mines. A mine operating in an inherently ""dusty"" seam may have a low concentration of respirable dust while a mine operating in a less dusty seam may have a high concentration of respirable dust. This discrepancy is a result of variables such as the effectiveness of ventilation or the efficiency of the water sprays. Consequently, it is very difficult to compare the dustiness of different coal seams by in-mine measurements of the respirable dust concentration. A laboratory test would more accurately characterize a coal seam according to its respirable dust production."

Jan 1, 1988

By John C. Machisak

Employment and related injury experience of the coking industry in the United States for 1957 contained in this publication is summarized under three general sections: (A) General injury experience: Tables 1 to 9: Current and comparable statistics on operating data, number, frequency, and degree of severity of injuries and major accident agencies involved in the cause of Injuries. Data are presented for the industry as a whole, for each type of oven, and for the States in which coke was produced.

Jan 1, 1959

By Albert J. Forney

Extensive studies have been made of the various effluents found in the Synthane coal-to-gas process. Analyses have been made of the waters, gases, and trace elements present in some of the streams. Results of analyses show the water effluents are the area where extensive research is needed.

Jan 1, 1974

By C. Gary Reiness

A safety glass eyepiece which had been repeatedly exposed to mine environment over a number of years was studied to determine some of its optical properties. In the regions from 385 to 400 mµ and from 625 to 760 mµ, the transmittance was less than the 89 percent required by the American Standard Safety Code for Head, Eye, and Respiratory Protection. From 200 to 320 mµ the relative transmittance of two parts of the eyepiece was found to vary widely, having a maximum of 38 percent difference at 315 mµ. Irradiation of the glass by ultraviolet light caused enhanced absorption in the range from 200 to 1,200 mµ. There was a time-dependent increase of 1016 color centers per cubic centimeter throughout this range after 36.5 hours of irradiation. The rate-of-growth curve for the optical density, at 243.5 mµ and 23° C, was resolved into linear and saturable components, indicating zero order and first order

Jan 1, 1968

By R. V. Ramani, C. B. Manula, A. Owili-Eger

PART 1 THE INPUT AND OUTPUT DATA AND THE MINE SCHEMATIC SHOWING THE FLOWS FROM COMPUTER SOLUTIONS FOR APPLICATION I

Jan 1, 1975

By M. S. Seehra, R. S. Pandurangi

"The interaction of amorphous silica particles with several hydrogen bonding agents (H2O,, C2H,OH, C,H,NO) was investigated by monitoring the changes in the bulk and surface IR vibrational modes of silica using photoacoustic spectroscopy, It is argued that the intensity of the silanol band at 3747 cm-1 provides (an inverse) quantitative measure of the interaction of surface groups, along with the shift in the broad hydroxyl band, the interaction following the order C,H,NO > C2H2OH > H2O.The use of IR spectroscopy to study the adsorption on solid surfaces is well documented in the literature,"" For example, hydroxylation of a clean silica surface results in the formation of the free silanol group Si-OH, with a sharp IR band near 3747 cm-1. Further hydroxylation produces a broad band near 3500 cm-1, which is believed to result from various hydrogen-bonded silanol bands leading to a multilayered surface structure of few nm.3-6 Earlier studies had indicated a relationship between the surface silanol band and various chemical activities of silica such as cytotoxicity,7-9 catalysis,10-12 and others.13 Recent studies from our group14-in which the intensity of the silanol band and cytotoxicity of silica, heat-treated at various temperatures up to 1095°C, were investigated-have provided a strong correlation between cytotoxicity and intensity of the silanol band.Coating of silica by PVPNO (polyvinyl-2-pyridine N-oxide with the empirical formula C7H8N0), a strong hydrogen bonding agent, is known to reduce the cytotoxicity of silica, presumably by chemically blocking the silanol groups from phospholipids.15 This interaction of the hydrogen bonding agents with the silica can be studied by IR spectroscopy, and Knozinger16 and Rouxlet and Semples17 have used transmission IR spectroscopy to study the effect of various chemicals on the surface IR modes of silica. However, one of the major disadvantages of transmission IR spectroscopy is that the sample preparation (grinding and mixing with KBr and pelletizing) usually distorts the surface modes (see, e.g., Ref. 14) and there is always a doubt about the effect of the sample preparation on the measured properties, In recent years, photoacoustic (PA) spectroscopy has become the technique of choice for studying the IR spectra of samples in their natural state, since no sample preparation is necessary.18,19 Moreover, according to a recent paper,20 the relative intensity of the surface modes in PA spectroscopy of silica particles is much higher than that in transmission FT-IR spectroscopy. Consequently PA spectroscopy is ideal for studying the surface chemistry, In this work, we have used PA spectroscopy to investigate the interaction of three hydrogen bonding agents (C7H8NO, C2H5OH, and H20) with the silica surface by monitoring changes in the surface IR modes, Our results show that the surface IR modes get perturbed to a larger extent than the bulk IR modes in interaction with the hydrogen bonding agents, Moreover, whereas in the earlier studies, the shift of the broad silanol band near 3500 cm-1 was used as a measure of the interaction with hydrogen bonding agents,16,17 here we show that the relative decrease in the intensity of the sharp silanol band near 3747 cm-1 also serves as a quantitative parameter for the relative surface coverage and surface modification, Details of this work are given below,The Cab-O-Sil samples of silica used here were obtained from the Cabot Corporation of Tuscola, IL, In our earlier studies,14,20 we have shown these particles to be amorphous and about 0.05 am in size, For coverage of these particles with H20 and C2H50H, the following procedure was employed. About 5 mg of silica was mixed with 50 mL of the liquid (H2O or C2H5OH) and refluxed for one hour, The remaining liquid was allowed to evap¬orate to dryness and 1 mg of the treated sample was used to collect the PA spectra. In the case of PVPNO, the amount that binds to Cab-O-Sil is taken from the data on quar"

Mar 1, 1992

By T. SPOLAN, G. W. Jones, R. E. Kennedy

Information relative to the explosibility of acetylene at elevated pressures and means of handling acetylene safely under these conditions is of considerable interest at present. American practice limits the pressure at which acetylene may be generated and distributed to poiIits of' use. The pressure in portable acetylene generators is 15 pounds per square inch gage. Tests made by the Bureau of Mines have shown that 15 pounds per square inch gage is too high to prevent explosiofiS of gaseous acetylene in the absence of air; in fact, dry acetylene gai can be exploded at pressures greater than 5.9 pounds per square inch gage. The Bureau has been interested in the explosibility of acetylene for many years because of its continued: use for illumination in many metal mines and its general use in cutting 1illd~--eldifigoperations in the mining maus-try.

Dec 1, 1948

By J. T. McCartney

In an effort to correlate the size of pyrite particles in coal and coal-particle association with the removal of pyrite before burning, the Bureau of Mines conducted a study of 61 coals presently being used for electric power production. The results were obtained by visual microscopic studies of polished briquets of minus l4-mesh samples. Mean pyrite particle sizes ranged from 20 to 400 microns and proportions of pyrite contained in coal particles to an extent greater than 50 percent by volume (estimated) ranged from 20 to 95 percent. These parameters were correlated with reductions in pyrite accomplished by float-sink tests at 1.60 sp gr on 14-mesh, 3/8-inch, and 1-1/2-inch samples. The correlation coefficients between pyrite removal and mean pyrite particle size were 0.89, 0.84, and 0.79, respectively, for these samples. Correlation coefficients between pyrite removal and coal-pyrite association parameter were 0.92, 0090, and 0.85, respectively. It is apparent that extent of pyrite removal can be fairly well predicted from microscopic analysis.

Jan 1, 1969

By H. R. Babitzke

To develop alloys suitable for use at elevated temperatures, columbium and tantalum were combined with tungsten, hafnium, vanadium, zirconium, and titanium, and the resulting alloys were evaluated with respect to fabricability, hardness, Electrical resistivity, strength at elevated temperatures, oxidation resistance, and bend transition. Of the 23 compositions tested, Cb-2OHf-5W-10Ti exhibited superior high-temperature properties. A recrystallized sample of this alloy was fabricable at room temperature, had a strength of 44,000 psi at 1,200° C, and had an oxidation rate of only 7.7 mg/cm2/hr at 1,000° C.

Jan 1, 1966