Search Documents

By Robert F. Randolph

Research on improving haulage truck safety, started by the U.S. Bureau of Mines, is being continued by its successors. This two-part article reports the orientation of the renewed research efforts, beginning with an update on accident data analysis, the role of multiple causes in these accidents, and the search for practical methods for addressing the most important causes. Fatal haulage accidents most often involve loss of control or collisions caused by a variety of factors. Lost-time injuries most often involve sprains or strains to the back or multiple body areas, which can often be attributed to rough roads and the shocks of loading and unloading. Part II will describe research to reduce these accidents, including improved warning systems, shock isolation for drivers, encouraging seatbelt usage, and general improvements to system and task design.

Jan 1, 1997

By Mark Sheppard

This paper is the third of a series recording the results of tests made at various quarries throughout the United States to determine (1) the relation between the size gradation of feed to, and product from, primary crushers, (2) the particle shape of the crushed. product, (3) the differences in gradation and particle shape produced by different types of primary crushers, and (4) the differences in gradation and particle shape caused by crushing different kinds of stone. Progress reports 1 and 2 dealt with comparisons of different types of crushers crushing the same type of stone. This report deals with relation¬ship between feed and product of two different limestones, as to size distribution and particle shape, when crashed in the same crusher.

Jan 1, 1938

By D. E. Fogelson

In a factorial experiment, blasting caps were detonated in three sizes of shotholes in mortar with three types of stemming--dry sand, wet sand, and hydrostone. Free-surface displacement pulses were recorded with a capacitive-displacement gage at a distance of 15 inches. The effects of decoupling and the type of stemming on the amplitude and the duration of the displacement pulse were determined. Both the amplitude and the duration of the displacement pulse were significantly decreased by increasing the decoupling, but they were little affected by the type of stemming.

Jan 1, 1965

By Fred C. Turin, Jasinder S. Jaspal, Alan G. Mayton, William J. Wiehagen

Dump site injuries occur in all major mineral industries. Working in elevated areas near an edge is a common hazard for operators of off-highway mobile mining equipment. In this Information Circular (IC), serious injuries involving haulage trucks working at dump sites are examined for the period 1988 to 1997. Data were acquired from injury reports gathered by the Mine Safety and Health Administration (MSHA). The IC is organized into three sections. The first presents an overview of the frequency and severity of injuries. The second analyzes injury characteristics using MSHA-defined data fields and author-defined injury classifications. Key findings are discussed in the third section. In summary, 370 serious injuries were identified that involved trucks at dump sites, of which 26 were fatalities. Although haulage truck activities at dump sites resulted in a small proportion of the total number of injuries at surface mines, these injuries were much more likely to result in death or significant amounts of lost time than most other surface mine injuries. These findings support the belief that haulage truck activities at dump sites are worthy of continued study by those interested in improving the health and safety of workers at surface mines.

Jan 3, 2001

By Wilbur I. Duvall

This paper presents arguments which show that a velocity seismograph should be used to measure building and ground vibrations produced by blasting . However , portable velocity seismographs suitable for this type of measurement are not commercially available . The paper describes how a velocity seismograph can be assembled from commercially available velocity gages , amplifiers , and recorders . Also , specifications are given which could be used in the design and manufacture of a portable velocity seismograph suitable for measuring vibrations from blasting .

Jan 1, 1964

By John Furness Park

This paper, which describes the mining methods and practices at the Jarbidge mines of the Elkoro Mines Co., is one of a series of papers being issued by the United States Bureau of Mines on mining methods and costs in various districts throughout the United States. LOCATION AND HISTORY The Elkoro Mines Co.'s property is located at Jarbidge in the northeast corner of the State of Nevada (fig. 1). The camp is 9 miles south of the Idaho line; the nearest railroad point is 70 miles to the northeast at Rogerson, Idaho. A road leading to the south and connecting with Deeth, Nev., is passable during the summer months; the heavy snowfall which generally takes place early in the winter usually closes the road until the first of July.

Jan 1, 1931

By J. Bootle

Marrow vein deposits will continue to be an important source of valuable minerals. Productivity per manshift is not keeping pace with operating costs. Increased mechanization of stoping operations must be obtained to create greater productivity at a reduced cost per ton. This application of mechanization may be to either present methods or to newly developed concepts. The total mine unit operations will be effected by increased productivity. Two approaches to increasing the mechanization of narrow vein stoping were studied with the intention of increasing stope productivity and decreasing stoping costs. A method of bringing efficient rubber-tired equipment into narrow cut and fill stopes was designed. It proposes to provide stope access by way of a ramp constructed on the stope fill. Impact breaking equipment was studied and specific applications proposed.

Jan 1, 1977

By W. T. Abel

Laboratory tests were conducted with a closed, recycling system to evaluate the effectiveness of solid-in-gas suspensions as heat transport mediums. Micronized graphite in helium or nitrogen was circulated by a centrifugal compressor to determine the feasibility of the method and heat transfer capabilities of the mediums. Suspensions were circulated without plugging or eroding the compressor or piping. At low flowrates and light (0.1 to 0.2 volume-percent) graphite loadings, slightly less power was required to transport a given amount of heat with suspensions than with helium alone. Graphite deposition on the heat exchange surfaces of the cooler decreased the heat transfer effectiveness at higher solids concentration. Efforts to eliminate deposition are described.

Jan 1, 1963

By Travis Q. Lyday

Australia was one of the world's principal producers of minerals and metals, and its minerals industry was a leading catalyst in promoting growth of the country. Australia was the world's largest producer of alumina, bauxite, diamond, ilmenite, monazite, opal, rutile, sapphire, and zircon. It was the premier exporter of alumina, coal, ilmenite, refined lead, monazite, rutile, and zircon, and was the second leading exporter of iron ore, after Brazil. Ranking behind China, the United States, the U.S.S.R., the German Democratic Republic, Poland, and the Federal Re-public of Germany, Australia was the seventh largest producer of coal (all grades) in the world. Australia was the fourth largest gold producer in 1988, after the Republic of South Africa, the Soviet Union, and the United States. It was the second largest producer of zinc, the third largest producer of nickel, the fourth largest producer of uranium, and the seventh largest producer of copper. 2 The country's mineral wealth was so extraordinary that it was virtually self-sufficient in most mineral commodities. Endowed with abundant resources of coal, natural gas, liquefied petroleum gas, and uranium, Australia was one of the few market economy countries that was a net exporter of mineral fuels. About 90% of Australia's consumption of crude oil was supplied by domestic production; this was expected to decline significantly about 1990, unless significant new oilfields were discovered.

Jan 1, 1990

By A. G. Starliper

The report covers studies by the Bureau of Mines on the removal of metallic values in two waste products from the Longhorn tin smelter at Texas City, Tex. One product was a slag that contained tin, tungsten, iron, tantalum, and columbium. The other product was a spent acid solution that contained tin, tungsten, iron, lead, copper, zinc, and silver and that came from presmelting treatment of impure tin concentrates. Molten slag was treated with sulfur or sulfur compounds and with coke, calcium carbide, or gaseous reductants to form tin sulfide that volatilized from the charge and to reduce tungsten along with iron and silicon to form a carbon-bearing metallic layer. The metallic layer was treated by an oxidizing alkali roast and then was water-leached to extract the tungsten. The waste acid was used in other experiments to dissolve an iron-tin- tungsten alloy (hardhead) obtained by direct reduction of the slag. An insoluble fraction containing tungsten, silver, silicon, columbium, and tantalum was removed, and copper was cemented on metallic iron, Tin was recovered by cementation on zinc plates, and lead was precipitated by adding sulfate ion. Iron was precipitated by increasing the pH which left a solution containing principally zinc. Slabs of hardhead were electrolyzed in an electrolyte consisting of waste acid to plate out groups of metals at different pH?s. The time did not permit thorough exploration of this method of treatment.

Jan 1, 1962

By Slavoljub D. Maksimovic

At some coal mines, methane gas is released during raise drilling. At the request of the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, the Bureau of Mines conducted ventilation surveys at different raise drill sites to assess various methods of reducing methane concentration. The resulting data indicate that raise drill shaft cavities are ventilated by air compressors, vacuum pumps, auxiliary blower fans, and free intake air from the surface. The compressors, pumps, and fans operate simultaneously or separately. At the bottom of the shaft cavities, ventilation is controlled by regulators and airlocks. Methane is monitored, measured, and periodically sampled on the surface, at the bottom, and at different levels in the shaft cavities. Maximum concentration of 3.5 percent was measured in one shaft in West Virginia. Air velocity down the raise drill shafts is always very low, Maximum recorded air down the drill stem was 3,000 cfm, which can be increased by adding air compressors. The best way to ventilate shaft cavities is through the simultaneous use of air compressors and vacuum pumps. If the methane concentration cannot be reduced with additional compressors, then the inside diameter of the drill rod should be increased, or larger pilot hole drill bits should be used.

Jan 1, 1981

By C. I. Pierce

The Bureau of Mines used an electrolytic tank model to investigate the response of guard electrodes of different dimensions under different simulated reservoir conditions. Sandstone disks from the Berea and Connellsville Formations were used as resistive beds in the model, and agar gel or water was used as conductive beds. In the experiments, bed thickness, hole diameter, mud resistivity, and bed resistivity were varied. The guard electrode is an excellent tool for determining true bed resistivity in the thin-bedded oil reservoirs of the Appalachian area. Vertical resolution and resistivity values are good when there is little or no invasion. Resistivity values are near true bed resistivity in beds thicker than about six hole diameters when the electrode-to-hole-diameter ratio is close to 1. However, low-resistivity muds cause false peaks to appear on the logs near bed boundaries in thick beds, and for resistive beds having a thickness approximately three to five times the hole diameter, apparent resistivities tend to be excessively high when mud resistivity is low.

Jan 1, 1966

By Martin A. Elliott

"INTRODUCTION During the recent war the Bureau of Mines was requested to obtain in¬formation on the temperature at which ammonium nitrate mixed with certa: contaminants would react rapidly. This information was desired in connection with an investigation of an explosion that had occurred during the evaporation, by air agitation, of volutions containing ammonium nitrate in which compressor oil that might have passed the filters was suspected of being a contaminant.During the course of this work it was found that mixtures of ammonium nitrate and zinc reacted rapidly at comparatively low temperatures: and since zinc could not positively be eliminated as a contaminant in the explosion in question, a series of tests was carried out, not only with mixtures of ammonium nitrate and compressor oil but also ammonium nitrate and zinc with and without oil. A few experiments were made with metals other than zinc.The investigation was not as extensive as might have been desired, owing to limitations -in time. The results are presented at this time in view of their current interest in connection with the Texas City disaster, in which a large quantity of ammonium nitrate detonated in the holds of two ships."

Mar 1, 1948

By R. Havens

During the course of the investigation of possible domestic sources of manganese, engineers of the Bureau of Mines examined and sampled two manganese mineral deposits in northeastern Utah. The Daggett Chief claims are situated in the northern part of Daggett County,5 miles southwest of Manila, Utah, and approximately 57 miles from Green-River, Wyo. Owners of the property are J.E. Harris Of Salt Lake City, Utah, Nels Palleson of Manila, Utah, and J. P. Larson. The manganese occurs in a vein 6 to 8 feet wide in a shale and sandstone formation. Two distinct occurrences Of manganese are present Within the vein, and samples of each were subjected to testing. Lot A, representing .probably the major portion of the Manganese; was composed of nodules and veinlets of manganese oxides in a semicompact; gray, shaly formation. Lot B represented a 15-inch vein of dense iron-manganese ore. .Most of the laboratory work at Salt Lake City, Utah, was done on these two samples; but preliminary testing also was carried out on a small sample, physically similar to lot A, submitted by the owners.

Jan 1, 1949

By W. A. Grosh

In 1951 the Federal Bureau of Mines became interested in the reports of copper-nickel mineralization in northern Minnesota. Several outcrops on the north side of the Duluth gabbro in the Kawishiwi River area were sampled by the Federal Bureau of Mines and George M. Schwartz of the Minnesota Geological Survey. Because these samples showed appreciable amounts of copper and nickel, a 100-pound sample of an un-altered outcrop was obtained for metallurgical testing. Results from this preliminary work were all favorable; therefore, in the fall of 1953 the Bureau of Mines diamond-drilled three holes near the outcrop of the con-tact between the Duluth gabbro and the Algoma granite. A total of 686 feet of NX size hole was drilled, and 100 percent of the core was recovered. Each hole intersected the contact, and the strike and dip for that locality were established. The core was split, and half was used for analyses and further metallurgical tests; the remainder was retained for permanent record in the Bureau of Mines core-storage warehouse.

Jan 1, 1955

By J. J. Rutledge, C. A. Herbert

In 1916 the Bureau of Mines, the Illinois Geological Survey, and the University of Illinois, working under a cooperative agreement, began an investigation of the subsidence of the surface above coal- mining operations. Four widely separated places where mining was in progress were selected as observation stations-one in the northern Illinois longwall coal field, one in the central Illinois coal field where the room-and- pillar panel system of mining was being used, and two in the thick coal of southern Illinois where the room-and-pillar panel system of mining was employed. These four points of mining activity gave a rather wide opportunity for observing subsidence when different mining methods were used. The four places selected for investigation of surface subsidence due to coal mining have been designated as follows: 1. A, in the northern Illinois longwall coal field, where the coal company has been operating coal mines for 30 years and where long- wall advancing is the only method of mining. 2. B, in Perry County, where panel room-and-pillar mining of a thick seam of coal is in progress and where mining operations have been carried on about 40 years. 3. C, in Macoupin County, where the coal company has been min- ing coal by the panel room-and-pillar method for about 15 years. 4. D, in Franklin County, where the coal company has been mining coal for 10 years by the panel room-and-pillar method.

Jan 1, 1927

By Wallace W. Roepke

The Bureau of Mines tested new designs of drag bit cutters with sintered diamond inserts instead of standard tungsten carbide tips. The bits were tested for orthogonal cutting forces, primary dust generation, and incendivity, with a standard plumb-bob type conical cutter (600 included tip angle) as the reference. Preliminary wear and impact-failure testing were also done. The results were mixed. Two new designs had forces similar to those of the reference bit, but one new design had about twice the normal force. This same design had almost twice the specific energy during shallow cutting but generated an equal or slightly lower amount of primary dust than did the reference bit. Incendivity was eliminated for two radial designs. One conical design had ignition only after more than 15 impacts, but the other conical design was incendive. Impact failure occurred, but not so quickly as anticipated. Over 7,500 impacts on a sandstone face, with a total cutting distance of more than 1,981.2 m, only scuffed the leading edge of the sintered diamond cutting face but put hairline cracks in the substrate mounting pad. Additional design and testing are needed to develop an optimum cutter, but prospects look good for this material.

Jan 1, 1983

By Will H. Coghill, I. L. Feld, G. D. Coe

"INTRODUCTION During the course of research on the beneficiation of the Big Seam iron ores of Birmingham, Ala., an urgent need was felt for quick iron assays of grab samples for mill control. Since the gangue minerals in these ores - quartz, limestone, and clay - all have about the same specific gravity, the use of a specific-gravity method was anticipated as a means of measuring the iron content. The idea of estimating the composition of a mineral mixture by measuring its specific gravity is by no means new. However, the usual method of carry in out this idea proved unreliable when applied to the Big Seam ores. The usual rapid method of determining specific gravity consists of measuring the volume of a known weight of sample that has been dried at high temperature. The inadequacy of this method led to the development of the rapid, modified, specific-gravity determination described in this paper.This work- was an incidental development resulting from research on beneficiation of iron ores by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and ore producing companies of the Birmingham district."

Jan 1, 1946

By R. N. Roby

In the course of the Bureau of Mines investigations for suitable sources of high-aluminum clay for the production of alumina, the Whiteware clay deposit was examined in August 1942 by G.N. Bennett, mining engineer, Bureau of Mines, Montana District Office. This report presents the factual data obtained by the investigation, which also includes data on trenching and drilling, and the results of some refractory tests and chemical analyses of representative samples of the clay later taken from some of the best trench exposures and from adit dumps.

Jan 1, 1949

By Mark Sheppard

This paper is the third of a series recording the results of tests made at various quarries throughout the United States to determine (1) the relation between the size gradation of feed to, and product from, primary crushers, (2) the particle shape of the crushed product, (3) the differences in gradation and particle shape produce- by different types of primary crushers, and (4) the differences in gradation and particle shape caused by crushing different kinds of stone. Progress reports 1 and 2 dealt with comparisons of different types of crushers crushing the seine tyre of stone. This report deals with relationship between feed and product of two different limestones, as to size distribution and particle shape, when crashed in the same crusher.

Jan 1, 1938