Search Documents

By Michael P. Hardy

The report described improvements and applications of the Hybrid Computer facility. Improvements implemented under U.S.B.M. Contract H0252035 included expansion of the capability to model nonlinear seam behavior, installation of a color video output display monitor, and further development of software capabilities. To demonstrate the capability of the system, firstly, the influence of nonlinear seam behavior response to the occurrence of coal mine bumps was fully investigated and secondly, the effect of improper mining sequence on bump occurrence was demonstrated. In addition, the system was applied to the analysis of a series of practical coal mine problems. Mines in three coal seams were analysed to investigate the parameters which contribute to the occurrence of coal mine bumps.

Jan 1, 1977

The annual reports of the supervising engineer of the seven sections comprising the Mining Division are assembled in the following pages and form the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

By P. G. Guest

Many of the gases and vapors used in anesthesia form explosive mixtures with oxygen or air. Sources of ignition for these mixtures always have existed, in operating and anesthetizing areas. When ether was first introduced, candles and gas-lights and coal stoves caused fires and mild explosions of the vapor-air mixtures. Today the chief causes of ignition are electrical. Fires and explosions are still much too frequent; and, because many of the mixtures are rich in oxygen, the explosions sometimes are very violent. Obvious sources of ignition, such as electric-power sparks and arcs in open motors, switches, and receptacles, as well as exposed incandescent wires and hot plates, usually are recognized by hospital personnel and corrected. A source of ignition that is not so obvious to many is static electricity. Until quite recently the presence of this hazard in a large majority of anesthetizing areas was not even suspected. However, numerous explosions -many of them fatal to patients -have been attributed, with good reason, to sparks from static electricity. In this paper the authors present facts to show the prevalence of static electricity in the average hospital anesthetizing area, and the degree to which this easily developed electrical form of energy constitutes an explosion hazard. An effort is made throughout to explain how static electricity behaves, why it is a hazard, and why certain safety measures are needed and recommended. Following the introduction and a short general discussion of static electricity, which incorporates a glossary of pertinent electrical terms, an account is given of inspections and tests made in a number of hospitals. This account includes many suggestions that should be useful to any person who plans to make similar inspections and tests. However, a comparison of materials and equipment used with those described in the report will reveal, in many cases, the potential dangers and obviate the necessity for tests. The hospital work was supplemented by considerable laboratory research designed to determine the spark energies required to ignite anesthetic-gas mixtures and the exact amount of time involved in developing the usual static charges. The results of this research are reported and the implications examined. The paper concludes with a general discussion of static and related hazards in anesthetizing areas and of the most urgent preventative measures.

Jan 1, 1952

By R. Ward Stahl

This publication is a revision of Report of Investigations 5363 updated to reflect the improvement in fire protection at selected coal mines and contains suggestions on what may be considered good fire protective equipment, suggested methods of organizing the attack on fires at various locations underground, and helpful hints on testing and evaluating firefighting facilities.

Jan 1, 1968

By A. J. Farstad

Characteristics of metal/non metal mines were evaluated to determine the suitability of applying the U.S. Bureau of Mines electromagnetic location system to the problem of locating trapped mines in metal/non metal mines. Statistical distributions of mine depths and overburden conductivities show that the existing USBM EM system is inadequate for most metal/non metal mines. Alternate approaches to trapped miner location in deep mines were identified and subsequent field tests were conducted at six (6) mines to evaluate their feasibility. The approach considered to be the most promising is one which utilizes the existing manpack transmitting system, modified slightly for a dual frequency output, in conjunction with a sophisticated signal processing receiver on the surface. The main advantage of staying with a "through the earth" approach is that the underground equipment can be kept simple, easily maintained, light-weight and inexpensive.

Jan 1, 1979

By W. J. Fene, J. J. Forbes

Through education, investigations, and studies and an expanded coal- mino inspection program the Bureau continued to dischargo the responsibility placed on it by Congress 39 years ago for promoting safety and health in the mineral industries. Although much still remains to be dono, definite progress was made in combating physical and psychological hazards in mines and plants. Accident-prevention cours os for coal-mine supervisory officials and special courses for coal-mine safety committeeman were inaugurated. First- aid, mine rescue, and other safety training was conducted for those engaged in all branches of the mineral industries. Assistance was given in recovery work after mine explosions and fires. Studies to reduce the danger of roof falls, the greatest single cause of fatal mine accidents, resulted in the development and adoption of new coal-mine roof-support techniques. Knowledge of the explosion and health hazards of mine and plant dusts and ways of pre-. venting them were advanced. Electrical equipment was tested for safety of operation in gassy coal mines, and emergency mine communications apparatus was developed and tested. More progress was made in the study of controlling flood waters that threaten life and property in the Pennsylvania anthracite region. More coal-mine inspections were made than in any previous year, and an impressive number of improvements resulted from the Federal inspectors' recommendations, even though many of them went unheeded. A program of con- trolling fires in inactive coal deposits on the public domain and private property was instituted during the year.

Apr 1, 1950

By Thomas Fraser, M. G. Driessen

This report is one of a series written by members of the Solid Fuels Mission to Germany describing wartime developments in the mining , preparation, and utilization of coal . The mission was organized early in 1945 under the auspices of the Technical Industrial Intelligence Committee , which cooperated with a counterpart British Committee . Engineers from other allied countries cooperated in some of the investigations . The Solid Fuels Mission operated under the direction of a steering committee headed by Dr. C. J. Potter , deputy solid fuels administrator . The personnel of the mission consisted of H. F. Yancey , in charge , J. W. Buch , Thomas Fraser , L. L. Newman , and L. D. Schmidt , of the Bureau of Mines ; H. H. Lowry , Director of the Coal Research Laboratory , Carnegie Institute of Technology ; H. J. Rose , vice president and director of research , Bituminous Coal Research, Inc .; and F. H. Reed , chief chemist , Illinois Geological Survey . Over 50 reports were written by the members of the Solid Fuels Mission . These and microfilms of supporting data obtained in the course of the investigations are on file at the Bureau of Mines , Washington , D. C. where they are available for public examination . The Office of the Publication Board in the Department of Commerce is prepared to furnish photolith copies , photostats , or microfilm reproductions of all declassified reports . A Bibliography of Scientific and Industrial Reports is issued weekly by the Department of Commerce , Office of the Publication Board , and is sold by the Superintendent of Documents , Government Printing Office , Washington 25 , D. C. , on a subscription basis . An initial payment of 10 dollars will provide for approximately 9 months , and subscribers will be notified when additional remittance is necessary . All subscriptions will begin with volume 1 , No. 1 , unless ordered otherwise . The Bibliography covers all materials and subjects and gives instructions for obtaining the desired items . The reports of the Solid Fuels Mission relate to the following general subjects : Mining methods in the Ruhr district of Germany , with special reference to mechanical cutting and loading equipment , pneumatic packing , and Diesel mine locomotives ; activities of industrial research laboratories supported by the German coal and coke industry ; coal preparation in western Europe ; low-temperature carbonization processes ; metallurgical coke from weakly coking coals ; low- ash electrode carbon from coal ; new developments in the production of metallurgical coke and the utilization of gas and byproducts ; briquetting brown coal and bituminous coal without the use of binders ; recent engineering developments in gas turbines and steam generators , with special reference to use of coal ; German coal-fired heating and cooking stoves; and the commercial extraction of coal with solvents for production of synthetic liquid fuels or chemical products . Numerous reports on the activities of German synthetic - liquid -fuels plants and the plants for the production of synthesis gas from solid fuels are available in the same office as the Solid Fuels Reports . It is planned to publish in this series of Information Circulars the more important reports or combinations of reports prepared by the members of the Solid Fuels Mission . A similar series on synthetic - fuel activities is being prepared .

Nov 1, 1946

By Robert A. Elgin

The Leadville mining-district (fig. 1) covers approximately 8 square miles adjacent to Leadville, the county seat of Lake County, Colo. It is famous for its large production of rich ores containing zinc, lead, copper, gold, and silver. Some manganiferous ores also have been produced.

Jan 1, 1949

By Daniel S. Witkowsky

The Pollution Prevention Act of 1990 provides few specifics to assist the non-fuel mining and mineral processing industries of the United States in achieving pollution prevention (P2) compliance. The U.S. Bureau of Mines (USBM) recognizes the absence of specific information to reduce pollution impacts from mining and mineral processing of hardrock and industrial minerals. Therefore, the USBM has prepared this publication to help reduce or eliminate environmental pollution and to assure the viability of these segments of the domestic mining industry. This report includes worksheets designed to help operators of mining and milling facilities to establish a P2 program. The report can also be used by citizen and environmental groups, State and local governments, and academia to gain an understanding of P2 as it relates to mining and mineral processing.

Jan 1, 1995

By Robert D. Perry

This report describes methods of reclaiming abandoned or inactive tailings ponds and dams. The investigated sites were selected tailings deposits adjacent to metal mines in the southwestern United States and the Pacific Northwest. The basic data developed for each site consisted of the following: a review of existing literature; a site visit that included sampling of the tailings and surrounding materials; laboratory and engineering studies; and development of reclamation plans. Laboratory tests determined the gold and silver content of each tailings deposit and the chemistry of the tailings and surrounding materials. Reclamation plans that include approximate costs were developed for five tailings deposit sites. These ranged in size from 52,000 to 103,000,000 tons. Our conclusions on the remining potential of each site are based on the tailings assay and other technical data. This study concludes that remining as a reclamation tool is feasible at certain sites. Included in this report is a remining program as part of the overall reclamation plan for two sites. Our preliminary results indicate that remining as a reclamation tool is feasible for only one of them.

Jan 1, 1981

By Felix du Breuil

Contract H0177044 included three objectives; (1) consolidate, maintain, and distribute information on STE approved lighting systems; (2) develop and present one-day seminars on underground mine lighting; (3) determine direct labor and hardware costs associated with the installation of mine illumination systems. All objectives were completed with results as follows: Task I - A file containing 1350 Statements of Test and Evaluation (STE) for all types of underground equipment was developed and publicized throughout the coal fields, A total of 40 requests for STE information was received and processed. Task II and III - A series of 50 seminars was scheduled and presented to 942 attendees throughout the coal fields. The seminars were well received and attendees indicated the information presented would be helpful in bringing their equipment into compliance. Holding a series of seminars in the coal fields, instead of a few in population centers, was favored by attendees. Task IV - Installation cost data obtained on 415 lighting systems indicate that the factors which most affect installation costs are higher hardware cost for DC powered systems and slightly higher manpower requirements for systems installed underground. Based on these data, the total cost to industry of retrofitting existing underground equipment could range up to $50 million.

Jan 1, 1979

By William G. Hedling

The operation of electric face equipment in underground coal mines has proven to be extremely hazardous to mining personnel, including equipment operators and others working in the vicinity of active equipment. Recent industrial engineering studies* of accidents and fatalities indicate that a major contributor to this hazardous situation is noncompliance with modern principles of human engineering, particularly lack of standardization of control configurations. Control configurations differ not only among different machine types, but also among the same machine types produced by different manufacturers. This lack of standardization can produce a high incidence of error in the operation of electric face equipment, thus creating a potential source of accidents. Other examples of non-compliance with human engineering principles are the widespread use of identical black, round control knobs (regardless of the function being performed), and the inappropriate location, spacing, and labeling of controls. Any or all of these factors may place the operator in a "negative transfer" situation, which means that control manipulations appropriate for one type of machine are different from (or even the reverse of) the control movements required to produce the same effect on other machine types. This situation increases the accident potential to the operator, as well as to others in the vicinity. Accident potential is further increased by circumstances which do not allow for large error tolerance-specifically, emergency procedures. Reports of accident statistics cite operator inexperience as a primary cause of most accidents involving underground electric face equipment. Several factors contribute to operator inexperience, including: 1. High personnel turnover 2. Employee absenteeism 3. Current union practice of bidding for jobs.

Jan 1, 1974

By Mackenzie Burnett

This program was initiated by USBM to quantify the respirable dust problem caused by the use .of roadheaders in underground metal/nonmetal mines with special emphasis on this problem in uranium mines. The contract called for the development of methods or equipment to alleviate the respirable dust and to implement the solution in a mine. Attempts to quantify the dust problem were made in the following way: survey of MSHA records, survey of state mine enforcement agencies, survey of mine records, dust measurements taken at two mines using roadheaders. The results of this study are not conclusive due to very limited and sometimes less than useful data; however, the study does indicate that a serious dust problem could and may exist. If and when roadheader use becomes more popular, it is almost certain that development of dust control procedures and equipment will be necessary. This contract was concluded without developing this equipment since only one roadheader is currently in use in an American uranium mine and the mine prefers not to participate in the program at this time. This report discusses the available data concerning respirable dust problems and presents a solution which can potentially help to solve the problem. The solution requires the use of blowing ventilation, on-board dust extraction at the source, and filtration, as well as continued use of water sprays. The on-site tuning of such a system is necessary to demonstrate the degree of improvement possible.

Jan 1, 1981

Research 83 highlights significant studies conducted during the past fiscal year at Bureau facilities and offices. Readers who want more information about the projects and studies summarized here can contact the researchers whose names and locations appear with each summary, General information on Bureau of Mines programs is available from the Office of Technical Information, 2401 E Street, NW., Washington, DC 20241. A listing of principal officials, a location map of field facilities, and a selected bibliography of publications and patents issued on Bureau developments during the past 3 years are provided.

Jan 1, 1983

By E. P. Carman

This report is the 20th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations; it is the second4/ to be issued on a calendar-year basis. Previous reports related largely to publications by Bureau authors during the reporting period. This one discusses the publications issued during 1955 and in addition describes briefly the work in progress during the year. Further details on the published work may be found by referring to the publications cited in the footnotes. The Bureau continues to direct its research and technologic work on coal toward safer and more efficient mining, improved preparation, and more effective utilization, with the ultimate twin goals of promoting conservation and insuring that coal will make its maximum contribution to the Nation's industrial capacity. Significant advances toward these goals were made in 1955.

Jan 1, 1957

By T. E. Swigart, C. E. Beecher

The Federal Government, as the largest lessor of oil and gas lands in the United States, is vitally interested in the conservation of those resources. This manual has been prepared at the direction of the Secretary of the Interior to call the attention of lessees of public oil and gas lands to the most common oil and gas field wastes and the best methods of preventing them; to outline the policies of the Interior Department on field operations; and to give information as to how the "Operating Regulations" of the department will be interpreted by the Bureau of Mines. The oil industry has progressed steadily. Present operating methods are much more efficient-and less wasteful-than those of a few years ago; moreover, the art of producing oil and gas is continually advancing. Public interest requires that improved methods, which will result in obtaining the greatest possible amounts of oil and gas from the natural deposits, shall be developed and used. Part I of this manual points out types of oil and gas wastes and suggests, in detail or by reference, the most practical and effective methods in current practice for stopping these wastes. Throughout Part I the department's operating policy is given, with interpretations of the "Operating Regulations" for enforcing every practical measure of conservation. Part II comprises the revised "Operating Regula-tions" which supersede all previous regulations and will govern future operations on public lands; it will be found in the pocket in the back cover of this bulletin.

Jan 1, 1923

By Robert L. Lagace

A prototype adaptive volume control for the loudspeaker output of mine trolley carrier phones was designed, built, and tested in the laboratory and in a mine. This volume control senses, and adapts to, the ambient acoustic noise environment in such a way as to produce a loud sound output under noisy conditions, and a quieter output under quiet conditions, thereby producing an understandable and unstartling volume level under all noise conditions. The design approach, prototype hardware, and test results are described, and the device is shown to be feasible for in-mine operations. The circuit design principles are easily applicable to currently available mina trolley carrier phones. Recommendations for practical improvements are included. An in-mine experiment to assess the practical feasibility and utility of the dedicated wire technique for overcoming poor trolley carrier phone system performance was designed, performed, and evaluated. The technique involves the use of a single, low-loss, properly terminated auxiliary wire, placed in the rail haulageway, which allows signals to naturally couple to and from the trolley wire/rail transmission line, and thereby significantly decrease the overall signal attenuation rate on the trolley wire/rail line. The in-mine dedicated wire experiment, results, and conclusions are described, and the technique is shown to be a valid and practical one for significantly Improving carrier phone system performance in mines. Guidelines for the installation and use of the dedicated wire are provided. Recommendations are made for obtaining further practical information on its performance and utility. A second in-mine experiment to assess the feasibility and utility of the low-impedance (low-Z) line technique for overcoming poor carrier phone signal transmission in mines was designed, performed and evaluated. The low-Z line technique involves the periodic connection of shunt capacitors between the trolley wire and the rail to artificially lower the line characteristic impedance. This causes the low impedance shunt loads encountered across the trolley wire/rail line to be less mismatched to the line, thereby reducing the overall attenuation of carrier phone signals. The results of in-mine experiments performed along unenergized and fully operational sections of trolley wire/rail line are described. The experiments were designed to measure line parameter such as inductance and capacitance per unit length, characteristic impedance, and propagation phase velocity, in addition to signal strength versus distance behavior under normal and low-Z line conditions. The low-Z line technique is shown to be valid, but not as practical as the dedicated wire technique which is recommended as the most favorable for most coal mine applications.

Jan 1, 1979

By A. C. Johnson

The Bureau of Mines explored the Three Kids deposit in 1941 as part of a strategic minerals program. Earlier mining and exploration had established the presence of a substantial tonnage of medium-grade wad ore, and drilling and sampling by the Bureau of Mines, in collaboration with the Federal Geological Survey, indicated an additional tonnage such that development and exploitation became more clearly feasible. Private interests, with Government support, undertook to produce metallurgical-grade manganese. The present paper describes the Bureau of Mines exploration and subsequent development. Manganese in the Three Kids area is found in one of the lower members of the Muddy Creek formation in a bed of fine sandstone and silt, which outcrops around the north edge of the River Mountains and generally dips 20° to 40° away from the hills. There is considerable variation in the thickness and grade of the ore. The ore is light weight, having a density of 1.2 to 2.

Jan 1, 1956

By L. C. IlsLey

Explosives have been fired electrically for several decades. Mountains have been tunneled, deep shafts sunk, extensive coal and metal mine workings excavated and, in times of war, railroads, buildings, bridges, and fortifications have been destroyed by means of electrically fired explosives. Modern engineering depends so much on explosives that their safe and efficient handling and especially their detonation are of prime importance to all those connected with the use of explosive agents. Electric shot-firing is only one method of igniting explosives, but it is rapidly spreading and because of certain inherent safety features should be encouraged. Data collected by the Bureau of Mines indicate that in the United States a large percentage of the blasting in quarries, shafts, and tunnels, and from 15 to 25 per cent of the blasts in mining operations, are set off electrically. The Bureau of Mines is interested in electric shot-firing because of its use in mining, and especially because electric methods, when properly applied, are undoubtedly safer than other methods commonly used.

Jan 1, 1926

By Joseph M. Pugliese

This work was done by the Bureau of Mines to provide quarry operators with an uncomplicated, first-approximation method for designing blast patterns, considering geologic structure, and to show the valid use of the technique by comparing drill and blast pattern dimensions used in the quarry with those determined by the presented method. The author visited 12 limestone and dolomite quarries in Ohio (Adam, Crawford, and Highland Counties), Wisconsin (Milwaukee, Racine, and Waukesha Counties), and Minnesota (Fillmore, Olmsted, and Wabasha Counties); observed the blasting practices; studied the major geologic features; and after discussion with the quarry managers, foremen, and blasters, compared the quarry blasting patterns with those as calculated by the empirical formulas (after R. L. Ash), with geologic structural considerations. When geologic structure such as bedding, jointing, folding, and caves, as well as explosive properties and field performance characteristics are accounted for in a manner suggested by the research, the presented empirical formulas may be used as a good first approximation. The included steps in planning a blast design and generalized blast patterns should be of help to the quarry operator. Design changes are recommended for those quarries where problems are occurring.

Jan 1, 1972