Search Documents

By H. E. Harris

An extensive experimental program was carried out to determine the variability of respirable dust samplers and to determine whether area dust sampling is feasible in coal mines. For sampler variability, it was found under laboratory conditions, that a single dust measurement could be as much as 0.30 mg/M3 from the true value at the 95% confidence level. Under actual underground mining operations, this difference could be as much as 0.52 mg/M3 in the 0 -5.0 mg/M3 range. The results from dust sampling on 175 production shifts involving over 2,500 on-man and area dust samples showed that area sampling is viable, but the field investigation did not establish necessarily where the best area locations were.

Jan 1, 1976

By R. S. Olsen

The Bureau of Mines is engaged in research to recover aluminum from kaolinitic clay and other nonbauxitic domestic resources. As part of this work, calcined Georgia kaolin was prepared by a process that prevents slime formation and makes the leached residues fast settling and easy to filter. The leaching reaction for calcined kaolinitic clay in a 5 pct stoichiometric excess of boiling 23-to 26-pct HCI was found to be zero order. Rate constants based on the weight-fraction of aluminum in the clay were found to be between 0.095 and 0.15 min-1 depending on feed preparation and leaching parameters. The mathematical relationships between aluminum extraction and time for both batch and continuous, stirred-tank operations were derived and verified experimentally.

Jan 1, 1983

By H. B. Humphrey

[EXPLOSION of gas and dust in coal mines, have caused death t lid injure to mines, and destruction of workings in all countries where coal is mined underground. In the United Stales the first reported explosion wits in Min; explosions have continued to the present. The danger to film ill it mine When an explosion occurs in not always measured by the violence created or by their nevi lies, to the area through which flame and Violence extend. As many, perhaps more, risen have died from gases and lade of oxygen (known as "after-damp") than have been killed by the blast and hart. Me explosions often are caused by it combination of factors, including concentration of methane in air, formation of clouds of dust, and the presence of a flame or spark. These explosion factors have varied with changes ill milting method and practises over the years, but the basis causes have always been the salve. Understanding of the causes and to acceptance of ways to guard against explosions and their effects have been slow to spread from investigates to officials and Own to bosses and miners. To a considerable extent there hats lawn a belief that explosions were a joining risk but might hr, put oil hut could not be presented. Such belief is based on the human failure to maintain and observe necessary precautions. These failures, caused by inertia to change, carelessness, or reliance on continuance, of past explosion-free years, are being reduced in number and effect by education of miners and supervisors and acceptance of higher prevention standards.]

Jan 1, 1959

By Joan Weinberg

Real gross national product (GNP) grew at a seasonally adjusted annual rate of 2.2% in the third quarter, down from a revised 3.0% in the second quarter, according to preliminary data from the U.S. Department of Commerce (table 1). The slowdown in the rate of growth was attributed to the summer drought, a larger trade deficit, and a decline in Federal spending for defense. Exports slowed from the second quarter, as the dollar, compared with other industrial country currencies, edged up. Imports of both consumer goods and capital goods rose sharply, with consumers buying more foreign cars, computers, and electrical machinery. Although net exports of goods and services deteriorated slightly from the second quarter, the U.S. trade position continues to be much improved from 1987 and first quarter, 1988. Business spending for new plant and equipment rose at a 4.6% pace, well below that recorded earlier in the year. The 3.5% increase in consumer expenditure was accounted for mainly by nondurable goods and services; expenditure for durable goods--those products lasting more than 3 years--rose only 0.4%. Inflation, as measured by the fixed-weighted GNP price index, rose at an annual rate of 4.9% in the third quarter. Prices rose slightly less than they had in the second quarter, when inflation reached a 6-year high. In September, 1988, the President signed a U.S.-Canada free trade agreement (FTA) which will eliminate all tariffs and most nontariff barriers between the two countries by 1999, thereby creating the world's largest open market. In 1987, U.S.-Canadian bilateral trade totaled $161 billion. The expansion of trade is expected to generate 5% higher growth for Canada and up to 1 % higher growth for the United States by the end of the century. The higher growth for the United States translates into an estimated 750,000 jobs, and $2.4 billion in exports. Canadian parliamentary approval of the agreement is still required before the treaty can take effect. The debate in Parliament is continuing, and the issue is not expected to be resolved until after the November 21 election.

Jan 1, 1988

By H. H. Dewing

The U.S. Bureau of Mines characterized Hg-containing wastes and used a thermal-desorption process to remove and recover the contained Hg. The wastes were generated by an electrical-parts plant engaged in the assembly of Hg-containing switches and contained phenolic resins and paper insulating materials mixed with soil. The average Hg content was 396 ppm. Numerous characterization tests showed the Hg was tightly absorbed and could not be removed or concentrated by leaching or gravity separation techniques. Laboratory retort tests showed the Hg content reduced to < 16 ppm in 2 h at 400 °C; rotary-kiln, thermal-desorption tests required 4 h at 450 °C. Airflow through the retort im¬proved thermal-desorption efficiency, but vacuum operation only slightly reduced the temperature needed for thermal desorption. Offgases from decomposition of organic materials were burned in a high-temperature afterburner and subsequently cooled in a heat exchanger to condense water vapor. Finally, the Hg vapor was condensed and absorbed from the offgas by activated charcoal. Mercury recovery was over 99.99 pct of the desorbed Hg. Thermal-desorption processes have had wide application to many Hg-containing wastes, and historical experience in Hg mining has demonstrated its potential cost effectiveness.

Jan 1, 2010

By R. A. Cattell

The Bureau of Mines recently observed its fortieth anniversary, and with the close of the fiscal year 1950 it completed 36 years of close cooperation with and helpfulness to the petroleum and natural-gas industries, whose technical problems it studies. Petroleum people likewise observed the ninetieth anniversary of the start of this truly American industry when "Colonel" Drake drilled the first well at Titusville, Pa., in 1859 (see fig. 1). Throughout the period, during which there have been many changes in the fuel and related economy of the country, this work has been carried on systematically by an organized entity of the Bureau first known as the Petroleum Division and in recent years as the Petroleum and Natural Gas Branch. Changes in the industries have been brought about partly by economic forces, partly by advances in technology, and in some measure by the impact of two world wars. As the needs of industry and the Nation have changed, so have the studies of the Bureau changed to meet these needs. Consistently, Bureau technologists and scientists have tried to keep in step with progressive movements; frequently, in fact, have taken the lead. Wherever possible, they have looked far ahead in their program of research, at the same time recognizing the needs of the hour.

Jan 1, 1951

By H. H. Schrenk

One phase of Bureau of lines work in health and safety is promotion of the use of safe, satisfactory, and reliable respiratory protective devices. To insure that devices embodying these features will be available the Bureau has established schedules of minimum requirements for oxygen breathing apparatus, gas masks4/, supplied-air respirators (hose mask, air-line respirators, and abrasive blasting helmet hoods, or masks)5/, and dispersoid (dust, fume and mist) respirators6/. Approval test, of oxygen¬-breathing apparatus are conducted by the Safety Division; approval tests of other types of respiratory protective equipment are conducted by the Health Division. These divisions comprise the Health and Safety Branch.

Jan 1, 1941

By Valois R. Shea-Albin

An accurate assessment of the vertical stress on a coal seam at depth is important for mine design. Vertical stress calculation techniques presently available either are not sufficiently accurate or cannot handle complex surface topography. Therefore, the U.S. Bureau of Mines developed a computerized method to calculate vertical stress exerted on surfaces at depth that includes the effect of topography. Two input data sets are required: a digital elevation model containing topographic elevations and a coal seam file defining coal seam elevations at depth. Boussinesq&apos;s equation then quantifies the vertical stress resulting from topography. The computerized method was tested on a coal seam overlain by a complex topography where a vertical stress map encompassing several square miles was produced. Results show that depth mitigates the affects of surface topography, while the coal seam topography has a direct effect on the vertical stress. In comparison to the computerized method, the direct stress method overestimates stress under hills and underestimates stress under valleys. The largest difference between the two methods occurs under the steepest topographic relief. A limitation of the computerized method is that stresses cannot be accurately determined near an outcrop.

Jan 1, 2010

In 2005, data obtained from the Mine Safety and Health Administration (MSHA) indicated a total of 922 underground (6.3%) and 13,744 surface (93.7%) mining operations.1

Jan 1, 2008

By W. M. Merritts

The control of coal dust created and released during the operation of continuous mining machines in bituminous-coal mines of the United States is a problem. The interest manifested in this problem indicates the seriousness of the hazards involved, particularly when the dust has not been abated at its source and has become air-borne. Officials of the Sunnyside No. 1 mine, Kaiser Steel Corp., were confronted with the problem of abating the coal dust created by operation of a recently installed continuous-mining machine, and they requested the aid of representatives of the Coal-Mine Inspection Branch, Bureau of Mines, United States Department of the Interior, in developing an effective method of allaying the coal dust at its source.

Jan 1, 1951

By C. L. Brown

Among the more recent developments for breaking coal in mines is the Airdox system, in which high-pressure compressed air is conducted to the points of application by means of heavy-duty steel and copper tubing. Stray electric currents can be detected on y of the compressed-air lines, and evidence of such currents is rev led, by arcs and sparks when contact is made between the tubing and mine track or other equipment forming a current path with the track. Explosive gas is liberated in many coal mines; therefore, from the standpoint of safety, it is desirable to eliminate all possible sources of gas ignition, including stray electric currents. The purpose of this report is to reveal the source, magnitude, and possible methods of controlling stray currents in compressed-air lines that are used in connection with Airdox systems. Stray electric currents have been studied in most coal-mining localities in the United. States where Airdox equipment is used. The information given in this report is based on the find of these studies.

Jan 1, 1949

By A. B. Hooker, L. C. IlsLey

"Field inspections and data relative to the use of rubber-sheathed trailing cables in mines show that much cable is ruined or its probable life shortened by being overheated in service.The length of cable required to make connection from a source of supply to a machine at the face workings may be 100 to 500 feet. As a rule, the cable is carried on a reel and unreeled as required; and thus in most cases soma of the cable is not removed from the reel. The overheating generally occurs in that part of the cable which is left on the reel.Factors that determine the heating of trailing cables are:1. The size of the conductors in the cable.2. The maximum energy to be supplied through the cable, based upon the horsepower of the motor and the degree to which the motor is loaded.3. The voltage of the supply and the variation of the voltage at the receiving end.4. The time length of current flow and whether continuous or intermittent.5. The kind of current (direct or alternating).6. The amount of ca· le left or the reel.7. The type of cable used.8. The kind of reel used.In connecti0n with an investigation of the general performance of rubber-sheathed trailing callas, the Bureau of Mines has made a limited study of some of these factors, including the following points:"

Jul 1, 1931

By J. Fletcher Smoak

Consumption of abrasive materials in the United States in 1981 was approximately $340 million, of which 37 % was industrial diamond (natural and synthetic), 39% manufactured abrasives, and 24% natural abrasives. Production and shipments of natural abrasives, excluding emery and industrial diamond, decreased in quantity 9% and 7%, respectively, when compared with that of 1980. Emery showed the largest change in output, decreasing 30% in quantity and 20% in value. Production of nonmetallic .manufactured abrasives material plus shipments of metallic abrasives material decreased 5% in quantity but increased 4% in value. Nonmetallic manufactured abrasives consisted of aluminum oxide (fused) and crude silicon carbide produced in the United States and Canada and accounted for 63% of the value of all manufactured abrasives. Metallic abrasives shipments included chilled and annealed iron shot and grit, steel shot and grit, plus cut wire, aluminum, and stainless steel shot and equaled 37 % of the value of all manufactured abrasives.

Jan 1, 1982

By George H. Schnakenberg

Automation of coal mining activities at the face offers improvements in worker safety, health, and productivity. Introduction of integrated computer-sensor systems to current mining machines will enable these machines to perform some of the most hazardous tasks through supervised teleoperation. The U.S. Bureau of Mines is pursuing the development of the enabling technology necessary to achieve this goal. The research program consists of both basic and applied research, each focused on the fundamental issues of computer and sensor technologies. Short-term research is directed to providing computer-assisted, remote supervisory operation of present underground equipment; the long-term goal is the development of progressively more intelligent mining systems. The research program includes a review of robotic machine and autonomous vehicle technologies and of current mining technology, which provides a base for developing innovative mining methods; research in navigation and guidance technology, emphasizing control of a continuous mining machine; research on coal-rock interface sensing technology for horizon control, and rib thickness control in highwall mining; the development of computer systems and hierarchical architectures for real-time control; and development of expert systems for machine system fault diagnostics and predictive maintenance. This report presents a brief background and the current status for each of these research areas.

Jan 1, 1989

By H. R. Pierce

Bureau of Mines engineers end others have endeavored to deter-nine a fundamental method for gauging the capacity of gas wells to deliver gas under different pressure conditions. Their studies show that for accurate gauging two factors must be determined: (1) The actual pressures at the face of the sand in the well (usually referred to as "at the sand"), acid (2) the relation between such pressures and the rates. of flow of c as through the sand. This paper, the first of a series, describes a method of attacking the problem of determining the actual pressures at the sand by means of observations of pressures and volumes at the well head.

Jan 1, 1929

By Jon C. Volkwein

The Bureau of Mines and many member companies of the Industrial Sand Association have been working in several areas to reduce personal exposure to respirable dust. Areas investigated include ventilation, modification of hardware, moisture addition to the product, and improved housekeeping practices. Ventilation systems have been devised and shown to contain 100 pct of a tracer gas released within the hood. An industrial clean air island has been developed and shown to reduce dust levels 90 pct at the opera- tor&apos;s position, Modification of hardware on a bag filling machine has been demonstrated to reduce dust 83 pct at the machine operator&apos;s lapel. This particular development has been termed a significant advancement in the state-of-the-art of bag filling by industry representatives. Addition of moisture to dried product materials has been tested with results showing dust reductions of 90 pct are possible!, Control of the moisture addition method still needs refinement and costs may be prohibitive. Dust sampling results clearly show the benefits of housekeeping practices such as building cleaning and vacuum sweeping. Rotation of work schedules is also effective for reducing personal exposure.

Jan 1, 1985

By J. H. East, D. Harrington

Fires in metal mines have resulted in some of the worst disasters in American mining history insofar as loss of life is concerned. One fire caused the death of 163 miners and individual less spectacular fires have cost the lives of scores of workers. Metal mines are often very deep, and the men working on numerous levels far removed from direct communication with the surface. In many instances they cannot be warned quickly of an emergency or a mine fire by telephone or other usual method of communication, or by messenger, flashing lights, gongs, sirens, or whistles. Telephones are not paricularly effective as a means of warning unless placed at all strategic points and with attendants always on duty; though telephones well placed have a definite value in any well-pla.mied emergency procedure in mines of all kinds. Messengers are slow and men working in remote parts of a mine would not receive a warning quickly enough. Most metal mines are not electrically lighted, except at or adjacent to shaft stations and in principal haulageways, and this limits the effectiveness of flashing lights. Electric gongs and sirens or whistles have been tried as warning signals, but the sound is quickly deadened and does not travel upward into the stopes, especially those of an extensive volume. Shutting off the compressed air is by no means satisfactory as a warning, as not infrequently it is stopped accidently, so that it loses its value as an alarm. The introduction of water into compressed air lines is undesirable as a fire warning and necessitates considerable care, especially in deep mines; pressure-reducing valves must be provided to reduce pressure that otherwise would break connections or split the pipe. A quick, effective method of warning miners underground of the existence of an emergency requiring them to leave the mine immediately, such as a fire on the surface or underground, is provided by the introduction of stenches in the compressed-air lines. This method of warning is by no means experimental, inasmuch as it has been used successfully for many years in

Jul 1, 1943

By W. M. Myers

[Utilization of small stone is recognized as one of the important problems of the lime industry. The term ?small stone&apos; is used to designate material that is too small for calcination in tie shaft kilo. The maximum dimension A such stone rosy be placed at four inches. The introduction of any considerable quantity of stone having demensions lee: than this into the charge of a kiln impedes the draft and readers successful operation of the kiln difficult on impossible. Attempts design a shaft kiln which would calcine stall stone satisfactorily have not been successful to date. Thousands of tons of this small stone arc produced daily, and while part of it finds a market, for it has many uses, the profit is usually small an competition is teen and prices are low. Production of the material is, however, so greatly in excess of market that surplus of hundreds or possibly thousands of Jose axe place daily in stock piles and classified as waste. in a few instances a fortunate combination of circumstances, such as a program of or other work requiring large quantities of concrete aggregate, may mate it possible some quarries to market this stone later at a profit, teat in general the chances A profitable utilization are slight, and the quarry operator has the expense of handling this waste stone and providing a storage site for it. The brittle nature of limestone makes it impossible to quarry the stone and crush, it to size suitable for the shaft kilns without producing an excess of undesirable fines. Elimination of fines by changes in quarrying or crushing practices cannot lee expected. On the contrary, the adoption of more modern methods of quarrying in recent years has increased the proportion of small material. The tendency is to blast the roan with large charges of explosives and crush it with mechanical crushers, which produces more fines than the older methods of careful blasting with small char yes and sledging the rock by hand.. We increasing use of underground mining of limestone has also increased the production of small stone, as blasting in the confined space of an underground stope shatters the rocs more completely than quarrying in the open. The use of the very friable limestones, such as the limestone of Florida for the manufacture of lime adds a new factor to the calcination of small stone. These friable lime limestones have a low tensile strength and crumble in the kiln, causing trouble. Successful calcination of these stones is accomplished in specially]

Jan 1, 1926

By W. C. Holliman

This report describes apparatus and procedure used for determining the vapor pressure of aviation gasoline in surveys of commercial aviation-gasoline characteristics made by the Bureau of Mines in cooperation with the Coordinating Fuel and Equipment Committee of the Coordinating Research Council, Inc. (CFR-CRC). The method is a modification of the Reid method, in which a mercury manor is substituted for the Bourdon-type gage of the Reid method. The method was used in earlier surveys made by the National Bureau of Standards in cooperation with the CFR-CRC, and was used in the Bureau of Mines surveys at the request of the cooperating organizations. It is designed for special research problems? particularly in vapor-lock studies, which require a precision greater than obtainable by the Reid vapor pressure method. A repeatability of + 0.01 p.s.i. average deviation from the mean may be obtained by method.

Jan 1, 1950

"When a metal-mining company takes out a workmen's compensation insurance policy, it does so to relieve itself of its uncertain and variable financial liability under laps requiring payment to employees for lost-time accidents, there-by passing the liability or to the insuring agency. For this service, or rather for the assumption of the risk, the insuring agency charges the mining company a price, or in insurance parlance, ""a premium"".The insuring agency depends upon a volume and variety of business to average the losses incurred by its individual policy holders, and determines its price to cover losses that are suffered and its cost of doing business.It is generally known that all types of insurance are founded on the theory of probability applied to large groups of risks, Workmen's compensation insurance is no exception, and the average price paid therefor must be based on the frequency and severity of accidents in the particular industry or branch of industry under consideration. The frequency and severity rates are determined by statistics, which, of course, unless standardized, kept carefully and consistently, and analyzed properly, are liable to be inaccurate and misleadingThe importance of large groups in arriving at an average price for insurance service can not be overestimated, For example the writer knows of one small group of some twenty metal-mining companies whose losses during the past two years exceeded their premium charge by 54%. Not a single individual company during the two years kept its losses below the premium rate. For several years the group as a whole has persistently exceeded its premium rate, Such risks are not profitable to the insuring agencies and can only be carried where a large volume of good risks will balance the poor risks, but in order to conform to good insurance ethics the premium rate must be based on averages for the industry as a whole, and kept sufficiently low to induce operators to sell their risks."

May 1, 1924