Search Documents

By Edward W. Parsons

The explosive-anchored rockbolt was field tested in six mines where rock conditions varied from incompetent shale or mudstone through fairly soft sand-stone to firm sandy shales. The purpose of the testing was to document, under a wide variety of conditions and in comparison to other rockbolt anchors, the quality of the anchorage produced by the explosive-anchored bolt. In addition, the length, strength, and design of the explosive charge necessary to produce positive anchorage up to the yield strength of the weakest component of the bolt were determined. A l4-inch length beaded explosive charge was found to be suitable, in general, in relatively weak strata, and the length can be reduced in more competent strata. Of the 127 explosive?-anchored bolts tested, 118 bolts produced an evaluated anchorage in excess of 17,000 pounds. Only 4 of 43 expansion-shell bolts and 4 of 14 wedge bolts produced anchorage this good. In preliminary tests, properly coupled explosive-anchored bolts did not ignite an explosive gas mixture. Some minor phases included in the investigation were as follows: (1) effect of explosive-anchored rockbolt on surrounding rock; (2) effect of time on anchored bolts based on torque tests; (3) effect of submersion in water on rockbolt anchorage; (4) pull tests to higher loads; and (5) ignition tests.

Jan 1, 1965

By Robert W. Ageton

The Bureau of Mines investigated the in situ vertical component of the rock stress in the rib of the haulage drift on the 6100-level of the Star mine, Burke, Idaho, using the flatjack and borehole deformation methods. The estimate of the vertical component of stress about 2 feet into the rib at a station along the haulage drift on the 6100-level of the Star mine by the flatjack method is approximately 5,875 psi, whereas the borehole deformation procedure at this station yielded a value of 5,500 psi for the same depth into the rib. The test zone is approximately 5,625 feet below the surface.No attempt was made to extrapolate stress estimates beyond the depth of the flatjack installation.

Jan 1, 1967

By Robert W. Geehan

The Bureau of Mines developed, by core drilling, the property of Nevada Scheelite, Inc., from October 5, 1943, to February 24, 1944. Claims of the corporation are near Rawhide in the northern portion of Mineral County, Nev. The purpose of the work was to determine possible reserves in the lateral and vertical extensions of a tactite zone which was being mined for scheelite. Production from this zone to January 1, 1944, was said to be 64,500 tons, with a recovery of 50,618 units of tungsten trioxide. The development work was done by the Bureau of Mines in cooperation with the U. S. Geological Survey and comprised a study of the geology, mapping the areas, and exploring the deposit by diamond drilling, trenching and sampling. Eleven holes were drilled for a total footage of 2,365 feet of holes.

Jan 1, 1950

By William Catron

This paper is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and cuts in the various reining districts of the United States. The mining methods described are those used in the mines of the Cananea Consolidated Copper Co., a Mexico corporation whose holding company in the United States is the Greene Cananea Copper Co. The mines are at Cananea, Sonora, Mexico, 25 miles directly south of the international boundary, approximately in 31° nor to latitude and 110 to 130° west longitude. Cananea is connected with the boundary towns of Naco and Nogales, Ariz., by a standard-gage railroad.

Jan 1, 1930

By P. R. Miles, J. K. H. Ma, J. Y. C. Ma, L. Bowman

"The bisbenzylisoquinoline alkaloids are compounds which can be isolated from plants and which exhibit a broad range of pharmacological activities. Perhaps the best known alkaloid of this group is tetrandrine (TT), a compound isolated from the root of a traditional Chinese medicinal herb, Stephania tetrandra. It has been tested for its effects on the cardiovascular system, tumors, and the lungs. For example, tetrandrine has been shown to act as a calcium entry blocker in cardiac sarcolemmal vesicles (King et a/., 1988) and has been used in China as a treatment for angina and hypertension. Its possible effects as a tumor-inhibitory substance have also been investigated (Kupchan and Atland, 1973). In addition, there are several lines of evidence to suggest that it is a possible therapeutic agent for the treatment of silicosis. Yu et a/. (1983) have shown that TT inhibits the development of experimental silicosis in rats when it is administered orally after intratracheal instillation of quartz. Other studies have shown that the alkaloid inhibits the synthesis of collagen by fibroblasts and the formation of silicotic nodules in rats exposed to silica (Huang et al., 1981; Liu et al., 1983). In fact, tetrandrine has been used clinically in China as an antifibrotic agent and has been shown to improve both the appearance of chest radiographs and the measurements of diffusing capacity in patients with silicosis (Li et al., 1981).Since tetrandrine may have a potential use as a therapeutic agent for fibrotic lung diseases, its effects on various pulmonary cells and tissues should be studied. Alveolar type II cells are located in the alveolar regions of the lungs and are important because they are responsible for the synthesis and secretion of pulmonary surfactant (Dobbs et al., 1982; King, 1984), regeneration of the alveolar epithelium after lung injury (Kauffman et al., 1974), and metabolism of foreign compounds (Bend et al., 1985). Furthermore, in silicosis, for which TT has been suggested as a treatment, there are increased amounts of pulmonary surfactant produced (Dethloff et al., 1986a,b) as a result of increased rates of surfactant synthesis by type II cells (Dethloff et a/., 1989; Miller et al., 1988). Because type II cells play a critical role in maintaining normal lung function and because type II cells are affected in silicosis, for which 'TT has been used as a treatment, we studied the effects of tetrandrine on energy metabolism in these cells in vitro. Energy metabolism was chosen because it is a basic cellular function which is neces-sary for other cellular processes to occur. Since type II cells depend on mitochondrial metabolism for energy production (Fisher et al., 1980), we examined the effects of tetrandrine on cellular and mitochondrial ATP production and oxygen consumption. Additional experiments were performed in an effort to determine if intracellular calcium levels may be involved in the TT-induced effects. A preliminary report of those results has appeared previously (Ma et al., 1991)."

Nov 1, 1995

By Florence L. Feicht, Carlton E. Brown

"INTRODUCTION This report contains information on the approximate size of the smallest dust Particles revealed by or the limit of visibility of various microscopic systems. The information was obtained mainly for use in interpreting and evaluating results of number-contentration and particle-size, determinations on, samples of unhygienic particulate matter collected from industrial atmospheres and in developing better methods for determinations nations.Some speculation and even controversy have been published on the limit of visibility of the widely used microscopic system (16-mm., 0.25-or 0.3-N.A. objective, and axial light-field illumination) used in counting the dust in the liquid medium from impinger, 4/ 5/ filter-paper, 6/ and other samples, but little or no quantitative data have been published on the limits of visibility of this or other microscopic' system.ACKNOWLEDGMENTSThe interest, encouragement, and assistance received from H. H. Schrenk, chief of the Health Division are gratefully acknowledged, as is all other assistance received in this study."

Aug 1, 1945

By J. G. Walters

This report presents the results of an investigation in Which the chloroform solubilities of coals and chars are related to rank, temperature of thermal treatment, time at a given temperature, vacuum thermal treatment, plasticity, oxidation, blending, and mass spectral analyses and molecular weights of the extracts. It was found that the quantity of chloroform extract obtained from chars can be altered by creating a vacuum above the charge during preparation of the char, increasing the time at temperatures within the plastic temperature range, and by utilizing different rates of heating to attain a given temperature. Relationships found between the chloroform solubilities of chars produced at temperatures within the plastic temperature range and the relative fluidities in this temperature range indicate that the chloroform-soluble portion of the char is a significant component of the plastic mass. Chloroform-extract yields from chars made from blends of coals cannot be calculated from chloroform-extract yields obtained from chars made from the component coals.

Jan 1, 1967

By Charles Vaught, Richard S. Fowkes, Ronald S. Conti, Barbara Fotta, William J. Wiehagen

The purpose of this study was to determine mine workers' state of fire-fighting preparedness and the technology being used to detect and respond to underground coal mine fires. To investigate this problem, 214 underground coal miners were interviewed by U.S. Bureau of Mines researchers. Frequency distributions of workers ' responses are presented in this report, along with segments of narrative accounts, to profile miners' fire-fighting capabilities. The data indicated that much variability exists from mine to mine and that there are several important changes operators may undertake in order to make miners better prepared to deal with fire underground: select appropriate sensors, establish and test a warning and communication protocol, construct a system capable of delivering hundreds of gallons of water per minute for sustained periods, institute formal fire preparedness audits, develop case studies of events that occur at an operation to use as teaching and assessment tools, and provide structured practice that can be incorporated into fire drills.

Jan 1, 1995

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made an the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By Cleo G. Rall

The method for determining the effective porosity of oil- and gas-bearing sands described in this report is a development of earlier methods (28)3/ devised by the Bureau of Mines. The apparatus bas been improved and made more convenient to use, but the procedure is essentially the same as that which has been in use for maw years. A tabulation at the end of the report gives the results of more than 4,800 porosity determinations for oil sands4/ in the fields of 13 States, A selected bibliography of references to articles containing descriptions and evaluations of various methods of' determining porosity is included in this report. The method was devised and developed at the Petroleum Experiment Station at Bartlesville, Okla., as part of the Bureau's research on fluid-energy relationships and on methods of improving the recovery of crude oil from underground reservoirs.

Jan 1, 1954

By Alan D. Hartman

Instabilities in electric steelmaking furnace arcs cause electrical and acoustical noise, reduce operating efficiency, increase refractory erosion, and increase electrode usage. The U.S. Bureau of Mines is investigating methods to stabilize these arcs. To perform experiments to test new hypotheses, Bureau researchers designed and instrumented an advanced, experimental single-phase furnace. This report describes this furnace, which was equipped with high-speed data acquisition capabilities for electrical, temperature, pressure, and flow-rate measurements; automated atmosphere control; ballistic calorimetry; and view ports for high-speed cinematography. Precise environmental control and accurate data acquisition allow the statistical design of experiments and assignment of rigorous confidence limits when potential furnace or procedural modifications are tested.

Jan 1, 2010

By C. F. Wingquist

As part of an ongoing study to determine how the wear of mining tools affects dust generation, the Bureau of Mines has measured bit tempera-ture rise during cutting of abrasive rock. Radial bit wear-flat tem-peratures generated by linear cutting in Berea Sandstone were measured as a function of cutting depth and speed. Depths of cut (DOC) were 1/8, 1/4, and 1/2 in, and cutting speeds were 10, 40, and 80 in/s, respectively. Temperature sensing was accomplished by emplacement of a miniature thermocouple into the center of the wear flat. Temperatures observed ranged from 2000 to 5000 C. Correlation between depth and temperature was weak. Temperature increased linearly with speed at 1/2-in DOC, but data taken at 1/8-and 1/4-in DOC produced inconclusive results. The results indicated that at least for deeper cuts (1/2 in), bit temperature, and therefore wear, can be reduced by lowering the cutting speed.

Jan 1, 1987

By S. R. Zimmerley

[In the course of a flotation investi~ntion, a siliceous gold ore was ground ir, R 'ball mill to ~inils 300-mesh. It mas found that the small mount of zlus 300-~esh mnterial had a go12 assw approximately twice that of the oricinal ors, md thst this oversize ~roduct also contained much abra?.ed iron. >!oreover, the gold assay of the abraded iron, which was separated ma~etic-dl:;, wno ei::ht tiaes tkat of the ore. These facts sug,~estsd th~t sone r3laticnshin existed between the abnormally high .gold content and the preseace of abrade4 iron. It was ciecided, therefore, to investl~ate furtkor ths acsoclation of the ;old nith the iron abraded from the balls durir-g grincing. As a nrelininary ex?rr>hent, a samy?le of siliceous gold ore 786 grolznd for 1-1/2 hours i;l 3 ball mill and the nuln was divided into two products electri~mag-etically. The racult s follow: ]

Jan 1, 1937

By James Westfield

A brief résumé follows of recent activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority (under Executive Order 9728) was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1958

By J. Koster

During the past several years, alunite from the Marysvale (Utah) region has been the subject of investigation by the Electrometallurgical Section of the Bureau of Mines. The nature and occurrence of this mineral, with considerable data on the Utah deposits, together with a number of results of preliminary experiments, have been given in a previous report.6/ The geology of the Marysvale region has been reviewed recently.7/ The present paper reports the results obtained by a method involving the sintering of alunite with boric acid and subsequent treatment of the sinter to produce alumina and potassium sulphate.

Jan 1, 1939

By F. K. McIntosh, A. F. Robertson, T. J. Ballard

"INTRODUCTION Molybdenum deposits occur in Halifax County, N. C., near the eastern border of the Piedmont province. The deposits are associated with a small granite body about 2 miles long and half a mile wide. Molybdenite is the principal ore mineral and is found as disseminations or thin stringers in quartz veins and occasionally in the enclosing granite or schist wall rock.The deposits were investigated by Almon F. Robertson and Charles J. Cohen, engineers of the Bureau of Mines, in 1942 and 1943, who recommended that the deposits be explored to supplement reserves of critical war minerals.The Bureau made the initial exploration of the deposits in July 1943 and continued its work to January 1944. Drilling was resumed from July to December 1946 to test the deposits at &eater depth than had been attempted during the previous exploration."

Dec 1, 1947

By James Paone

This report on the state of the art of horizontal boring technology for underground power transmission installations was prepared by the Bureau of Mines at the request of the Department of the Interior. This paper describes the different machines and methods used in augering, impacting, pushing, drilling, and machine tunneling horizontal holes through soil and rock. A review of the borehole survey and guidance tools and techniques applicable to these methods is also given. Nonboring methods used for emplacement of power distribution and transmission lines are briefly discussed. The paper ends with a brief technical forecast, an analytical summary of the state of the art, and recommendations based on power industry needs. Horizontal boring techniques for power distribution lines installation are adequate to meet the requirements of the power industry, particularly where such burial involves relatively short distances in soil or soft rock. For burying power transmission lines, particularly in the harder rocks and over relatively long distances, horizontal boring methods are not as well advanced. Research and development as well as economic incentives to equipment manufacturers could substantially improve the state of the art. Obstacle detection and guidance systems for directing boreholes to specified targets need major improvements to meet the requirements of the power industry for underground burial of distribution and transmission lines

Jan 1, 1968

By JOEL H. SWARTZ

During a series of resistivity measurements carried out in 1929 and 1930 a number of questions arose concerning the effect of topography on the character of the curves and the depths attained , the ratio of true depth to certain radii interpreted as representing depth , etc. To answer these questions it was decided to undertake a series of experimental investigations on artificial strata . It is the purpose of the present paper to present the results of the studies thus undertaken .

Feb 1, 1931

By William A. Stickney

The zirconium-hafnium separation plant at Albany, Oreg., was the result of a chain of events that started with studies by A. R. Kaufmann at the Massachusetts Institute of Technology. Variations in the listed neutron-absorption cross-section of zirconium caused him to suspect a misprint. As a result of these discrepancies and following his suggestions, Oak Ridge scientists made studies establishing a value of 0.4 barn or lower. This meant that the potential of zirconium for reactor application was greatly enhanced. Since hafnium is invariably associated with zirconium and has a high neutron cross-section, it was necessary that an efficient hafnium-separation method be developed before the superiority of zirconium as a structural material in nuclear reactors could be realized. The Albany plant was built and operated for the Atomic Energy Commission (AEC) under Letter Agreement AT-(11-1) -140, patterned after a plant operated by the Carbide and Carbon Chemicals Corp. at Oak Ridge, Tenn. Construction was begun in April 1951. Hafnium was to be extracted preferentially as hafnium thiocyanate from an aqueous mixture of zirconyl and hafnyl chlorides in hexone (methyl isobutyl ketone) by a liquid-liquid countercurrent system.

Jan 1, 1959

By H. R. Shell

Of three known compounds in the ternary system K20 - PbO - SiO2, one having the composition K2Pb4Si8021 crystallizes into a structure with asbestiform properties. This compound, whose silicon-oxygen ratio is between that of the layer silicates (for example, mica) and the double-chain amphiboles, crystallizes in the tetragonal system. It malts, apparently congruently, at 779° C. The fiberized product prepared from crystals is fluffy and closely resembles natural asbestos in appearance, but is more brittle and has less strength. However, potassium-lead silicate may be separated into fibers with a uniform diameter of 200-300 A.U., and the fibers show with the electron microscope the s criteria that have been interpreted as indicating a hollow tube structure in chrysotile asbestos. Since very few inorganic crystalline compounds have such a structure, the material has unusual scientific interest. Microcrystalline potassium-lead silicate was rapidly and completely formed when powdered glass of the same composition was heated to 650° - 700° C, but macrocrystals grew only slowly from the viscous massive glass. Maximum growth rate was 0.12mm. per hour at 700° C.

Jan 1, 1957