Search Documents

By E. C. Lane

This report presents the results of the Bureau of Mines' twenty-first semiannual survey of motor gasoline marketed in the United States. The 12 cities in which samples were collected have teen chosen as representative of the more important marketing territories, as it is obviously impractical to obtain a sample of every gasoline sold in the entire country. The survey reveals that the motor gasoline which is being marketed in the United States this winter is decidedly more volatile than that sold a year ago. Samples from all cities show a decided improvement in volatility except those from Laramie, Wyo., which show a small decrease in volatility.

Jan 1, 1930

By J. L. Thompson

The U.S. Bureau of Mines conducted a water-jet-studies program using a single-bit, in-seam test unit to determine effects of a moderately high-pressure (up to 10,000 psi) water-jet-assisted cutting system on rock weakening. The in-seam test unit was used to obtain cutting force data in tangential, normal, and side force directions. Conical continuous miner and radial longwall miner bits were used to penetrate test samples of coalcrete, Berea sandstone, and Indiana limestone with unconfined compressive strengths of 4,600, 8,000 and 10,000 psi, respectively. Depth of cut in the coalcrete tests was 1 in, with 2-in cut spacing (2:1 ratio). Because of cutting equipment and instrumentation limitations, the Berea sandstone and Indiana lime-stone were cut using a 0.5-in depth of cut and 2-in spacing (4;1 ratio). Bit velocity was maintained at 25 ft/min for both bits. Each specimen and bit type was tested using 0.3-, 0.6-, 0.8-, and 1.0-mm-diam nozzles and water-jet pressures of 2,500, 5,000, 7,500, and 10,000 psig. Water-jet-assisted cutting decreased average resultant conical and radiallongwall bit cutting forces 6.4 and 8.4 pct in coalcrete, 5.5 and 1.4 pct in Berea sandstone, and 2.0 and 5.5 pct in Indiana limestone. Slight reductions of power requirements resulting from water-jet assist were ascertained during these experiments.

Jan 1, 1989

By J. Ronald Lawter

The purpose of the work described in this report was to measure the effects of diesel engine emissions on the air quality of work areas in a coal mine. Concentration measurements of a number of diesel related air contaminants were made at the Martin County Coal Corporation Mine in Inez, Kentucky. Compounds measured included carbon dioxide, carbon monoxide, formaldehyde, nitric oxide, and nitrogen dioxide. In addition, concentrations of the two classes of odorous compound;, aromatic hydrocarbons, and oxygenates were obtained along, with aldehyde concentrations. Surveys were made of the mine by odor analysts to determine the perceived intensity of diesel-produced odors. It was found that the concentrations of the measured species were well below their Threshold Limit Values. Odor intensity levels in the moderate to strong range were observed in the mine.

Jan 1, 1977

By E. L. Garton

The Bureau of Mines for a number of years bas been conducting an investigation of crude petroleum from producing fields in the United States and the Western Hemisphere and has published a series of reports on these fields. Analyses of crude-oil samples from many oil fields of Oklahoma are given in Bulletin 2915. Analyses of 21 representative crude oils from various producing zones of the Oklahoma City field are given in this report. A close study of the analyses reveals very few differences in the general characteristics and chemical properties of these oils.

Jan 1, 1932

By Ronald H. Church

The Bureau of Mines tested & ground penetrating radar (GPR) system in the central Florida phosphate district. to determine the feasibility of utilizing GPR technology for subsurface cavity detection. The test area is located in karst topography where sinkhole development is prevalent. State regulations require subsurface drilling of damsites to identify underground anomalies; however, this method is not totally accurate in locating subsurface cavities that could lead to sinkhole development. An electromagnetic method of identifying anoma-lous subsurface conditions could reduce or eliminate the possibility of dam failure due to sinkhole development. The Bureau devised a GPR system that successfully penetrated over 50 ft of overburden and gave recognizable radar return signals characteristic of a rock-cavity interface.

Jan 1, 1986

By Mulligan John J.

The Bureau of Mines investigated lode tin deposits on Potato Mountain, Seward Peninsula, Alaska. Tin was found to occur as cassiterite associated with quartz, tourmaline, pyrite, arsenopyrite, and earthy clays, but the deposits lack the varied accessory minerals commonly found in tin districts. The tin-bearing deposits are in metasediments along minor breaks and bedding planes but not in the crushed earthy filling of major faults. Cassiterite and sulfides occur with quartz in veins, both with and without earthy clays, and disseminated through tourmalinized wall rocks. The deposits are characterized by irregular segregations containing 1 to 10 percent tin within zones averaging not over 0.25 percent tin. The largest segregation exposed is on the summit of a low hill on the east-central slopes of Little Potato Mountain; most of the outcroppings are in an area trending east to west, roughly 10 to 30 feet wide and 300 feet long. Sample values ranged as high as 12 percent tin, but the average grade may be about 1 percent tin. The extreme irregularity of both grade and composition precludes a more exact determination. Similar concentrations are scattered for over 1,000 feet to the west and north, but these are smaller and lower in grade. Elsewhere on Potato Mountain, generally similar deposits occur as clusters of veinlets at widely separated points in the metasedimentary walls of major faults.

Jan 1, 1965

By W. C. Holliman

This report on the characteristics of commercial aviation gasolines presents compilations of inspection test data furnished on their products by manufacturers of commercial grades of aviation gasoline, and special data obtained in Bureau of Mines laboratories on samples of these gasolines. Data and physical samples for the survey were submitted by 15 manufacturers on 18 grade 80, 21 grade 91/98, 22 grade 100/130, and 10 grade 115/145 aviation fuels.

Jan 1, 1948

By John C. Edwards

The U.S. Bureau of Mines has constructed a smoke chamber and developed sensitivity tests for smoke detectors. Response of ionization-and optical-type commercially available smoke detectors have been investigated. Six smoke detectors were measured with respect to visually obscuring smoke characterized by a corresponding optical density for smoldering and flaming coal combustion in the smoke chamber. It was determined that for one type of ionization smoke detector the alarm time was nearly equivalent to that of an odor monitor's alarm for smoldering coal combustion experiments and earlier for flaming coal combustion experiments. The experiments showed that an average CO concentration of 5 ppm corresponded to an optical density of 0.022 m-l for smoldering and flaming coal combustion. Two of the commercially available ionization-type smoke detectors were more responsive to flaming than smoldering coal combustion at an optical density of 0.022 m-l, whereas the optical smoke detectors showed the opposite trend. The responsive characteristics of the detectors evaluated with respect to known smoke conditions in the smoke chamber shows their potential for use as mine fire sensors or part of a mine atmospheric monitoring system to improve mine safety.

Jan 1, 2010

By E. G. King

This publication presents original thermal data for a typical variety of perlite and supplies basic information for use in computing energy requirements in processes for expanding perlite. Perlite has been defined by Raiston 4/ as any silicious lava containing dissolved water in sufficient amount to errand into bubbles when the material is quickly heated to a suitable point in the softening range." The uses of expanded perlite in) the construction and ceramic industries have been discussed by Ralston 4/ and King. 5/ The work described here had a dual purpose: (1) It was desired to ascertain quantitatively, using a typical variety of perlite, just how firmly the contained water is held, and (2) it was desired to obtain basic thermal data sufficient for energy-requirement calculations in processes for expanding perlite.

Jan 1, 1948

By L. B. Pankratz

The Bureau of Mines measured heat capacities of alpha and beta spodumene (LiAlSi2O5) and of beta eucryptite (LiAlSiO4) over the temperature range 51° to 298° K. The entropies at 298° K were found to be 30.9 ± 0.2 cal/deg mole for alpha spodumene, 36.9 ± 0.3 cal/deg mole for beta spodumene, and 24.8±0.2 cal/deg mole for beta eucryptite. High-temperature heat content measurements above 298° K were conducted for the same compounds. Measurements were made to 1,150° K for alpha spodumene, 1,600° K for beta spodumene, and 1,470° K for beta eucryptite. Tables of heats and free energies of formation are given from the elements and from the constituent oxides.

Jan 1, 1967

By N. A. C. Smith

The Bureau of Mines motor gasoline surveys have been conducted in January and July, during 1920 and 1921. The Bureau has obtained and analyzed samples of gasoline representative of that marketed in the larger cities. These surveys have indicated that the gasoline on the market during the winter months is more volatile than that sold during the summer months. Naturally, the motorist desires a more volatile gasoline in the cold winter months, as it affords greater ease in starting. The fourth semi-annual motor gasoline survey, conducted during the month of July, shows an interesting relation between the market price and the quality of motor gasoline. This is particularly evident if figures obtained today are compared with those of a year ago. At the time the Bureau of Mines conducted its summer survey of motor gasoline last year, the average tank wagon price of gasoline was 28.2 cents per gallon. This year it was 21.2 cents, a drop of practically 25%.

Jan 1, 1921

By Francis X. Cannaday

The purpose of this investigation was to find whether the moduli of elasticity obtained were the same for the following methods : ( 1 ) Deformation of a borehole in a prism subjected to uniaxial stress ; ( 2 ) deflection of a thin beam of uniform cross section uniformly loaded ; ( 3 ) sonic - pulse velocity measurements , and ( 4 ) strain measurements on a prism under uniaxial stress . The rock tested was chosen for its good elastic behavior and relatively good homogeneity and elastic isotropism . The same rock was used for all methods . Results indicate that for given environmental and stress conditions the moduli obtained by each of the four methods check one another within the limits of experimental error and that the differences introduced which are characteristic for each method are smaller than physical variations within the rock tested .

Jan 1, 1964

By J. R. Koehler

The U.S. Bureau of Mines (USBM) ground control research program includes several projects focused on developing design criteria for yielding-pillar-based longwall gate road systems. As part of this program, mining practices at the Sunnyside Mines, Sunnyside Reclamation and Salvage Co., Sunnyside, UT, are being documented to preserve the long history of yield pillar system evolution on the property. Published information describing the specific in-mine performance of the numerous gate road configurations utilized at the Sunnyside Mines is very limited. To overcome this deficit, USBM personnel interviewed 30 longtime mine employees representing nearly 700 years of mining experience at the Sunnyside operations. Mining conditions in 12 specific areas in the Nos. 1, 2, and 3 Mines were discussed in the interviews. Also, broad topics such as general mining practices, safety, and geology were often addressed during the discussions. Comprising the body of this report is an extensive record of the events and conditions experienced while mining the identified areas. In addition, eight significant conclusions were developed that accurately summarize the general opinions of the interviewed personnel regarding mining conditions and practices at Sunnyside.

Jan 1, 1994

By R. B. Tippin

The heavy liquid separation (HLS) process was investigated by the Bureau of Mines to develop a means of concentrating minerals from natural ores, Various spodumene ores were tested in a 0.4-inch diameter cyclone using pure tetrabromoethane (TBE) as the heavy liquid. Studies were initiated to examine the influence of (1) pulp density (2) feed grade, (3) cyclone pressure, (4) cyclone apex opening size) (5) cyclone vortex finder opening sand (6) mineral particle size on the separation efficiency. Each of these factors was found to affect the heavy liquid separation in some degree; the mineral particle size exhibited the greatest effect and the ore feed grade the least. Conditions necessary to yield an 85 percent spodumene concentrate with an 85 percent recovery were determined to be: 70 psig pressure, 10 percent solids, 0.08-inch apex opening, 0.11-inch vortex finder opening and a minimum amount of minus 200-mesh fines in the feed. Operation of multiple cyclones in series resulted in spodumene concentrates assaying over 90 percent and indicated mineral recoveries exceed-in 90 percent.

Jan 1, 1967

By C. Kenneth Eilerts

A method is described for controlling instability in finite-difference computations of liquid saturation near the borehole of a recovery well. Differences of pressure-and saturation-dependent variables are indexed offcenter, upstream and downstream alternately, to provide a stabilizing average. It was found that size of the time step could be increased by a factor of 4 without loss of numerical stability. Finite differences of the variables occur in a variety of relative numerical sizes and combinations. Those relationships of the differences that contribute to instability may be identified by the computing program in which they occur and modified to assist convergence of the computations and execution of the partial differential equations of liquid and gas flow.

Jan 1, 1971

By Arthur V. Petty

The Bureau of Mines has investigated the effect of refractory oxide additions, introduced in soluble form, on the refractory properties of 42-, 58-, and 70-pct-A1203 brick. Brick having porosities ranging from 12 to 16 pct were impregnated with solutions containing chrome, chrome-iron, zirconium, calcium, magnesium, cobalt, nickel, tin, and manganese ions. Additions of some of these ions provided dramatic improvements to such properties as hot modulus of rupture, hot load, and particularly slag resistance. These improvements can be related to reduction of porosity, amorphous grain boundary phases, formation of more refractory bond phases, and reduction of the wettability of Al203-containing refractories by metallurgical slags. Fifty-eight-percent-AI203 brick, impregnated with chrome, showed hot modulus of rupture, hot load, and slag resistance two to five times better than those of untreated 70-pct-AI203 brick. This could result in reducing the Nation's dependence on imported refractory-grade bauxite generally required for high-A1203 brick, as domestic alumina resouces could be used to produce the improved refractories.

Jan 1, 1984

By Charles Vaught, Henry J. Kellner, Michael J. Brnich, Henry P. Cole, William J. Wiehagen

In 1985, U.S. Bureau of Mines and University of Kentucky researchers began a series of studies relating to self-contained self-rescuer (SCSR) donning proficiency. During the next 5 years investigators examined a number of factors that have a bearing upon miners' ability to put on and use the apparatus in an emergency: the procedure being taught; availability and utilization of training models; opportunities to practice; hygiene; and on-the-job training. This report presents an overview of that research. It is concluded that companies should adopt a hands-on training protocol that allows them to integrate SCSR donning practice into other workplace routines such as fire drills.

Jan 1, 1993

By C. O. Hawk

Distillable oils derived from coal were desulfurized and hydrogenated at 2,500 psig in a two-step vapor-phase catalytic operation to give a product rich in saturated cyclic hydrocarbons. The first step was mainly a desulfurization at 400 C, the second a saturation at 300 C. One of the oils used as feed stock was from low-temperature carbonization of a bituminous coal, the other was from the liquid-phase hydrogenation of coal in the Bureau's pilot plant. The product from the saturation step was distilled to remove the light ends and high-boiling residue and to recover a fraction having acceptable properties with respect to heating value, density, freezing point, viscosity, and boiling range according to specifications suggested by the Air Force for ultra-high-speed aircraft fuel. Quantities of the fuel fraction available were too small for the thermal stability test approved by the Air Force. The experiments, performed on laboratory scale, comprised mostly a study of the effect of varying the oil feed rate (at constant oil-to-hydrogen ratio) on the yield of the desired fuel fraction. The yield of the fuel fraction made from low-temperature carbonization oil was a little more than 1 percent of the weight of coal carbonized; that from coal-hydrogenation oil was about 12 percent of the weight of coal hydrogenated. A few attempts to do both desulfurization and saturation in one operation with sulfur resistant catalysts, developed for vapor-phase hydrogenation or hydroforming, were unsuccessful. By leaving the low-boiling ends in both feed stocks to desulfurization, another product was obtained: a low-sulfur aromatic cut boiling below 200 C. This material would be suitable as a solvent or a chemical raw material.

Jan 1, 1965

By V. A. Nieberlein

The purpose of this investigation is to determine the reserves of columbium (niobium) minerals in Arkansas and to develop metallurgical methods for concentrating the minerals and extracting the metal. The columbium resources of central Arkansas were explored by drilling and trenching, and a number of samples were taken. On the basis of this exploration the known reserves of the metal were estimated to be over 78,000,000 pounds. The reserves could possibly be extended by additional exploration to 150,000,000 pounds.

Jan 1, 1954

By A. H. Beebe

This paper describing the operations of the Cresson mine of the Cresson Consolidated Gold Mining & Milling Co. at Cripple Creek, Colorado, is one of a series of papers on mining methods and costs being prepared by the United States Bureau of Mines. The Cresson has recently been the most, important mine in the Cripple Creed district. During 1932 and 1933 an average of 230 tons of new ore (excluding dump material) that averaged about $10 in gold was shipped daily; 150 to 175 men were employed. Stoping was by the shrinkage method exclusively. The ore was screened washed, and hand-sorted at the surface and shipped to the Golden Cycle mill at Colorado Springs for treatment. A considerable proportion of the production was made by lessees working under the so-called "split-check" system. The authors are indebted to the management of the Cresson Consolidated Gold Mining & Milling Co. for permission to publish this paper.

Jan 1, 1934