Search Documents

By W. E. Pittman

The Bureau of Mines, as part of its Health and Safety Technology Program, is conducting research on the use of ground penetrating radar (GPR) for mine hazard detection. GPR offers a possibility of mapping immediate below-surface geologic conditions, including faulting and other anomalies, thereby exposing potential safety hazards to miners. This report summarizes a literature review of the current status of GPR research in and outside the Bureau.

Jan 1, 1984

Provide the mining industry with a simple, accurate and readily available means of measuring the gas flow from pipe outlets such as gob holes Approach The Bureau of Mines conducted laboratory studies to establish correction or method factors for anemometers when used to measure gas flow from pipe outlets. Using the Anemometer Anemometers are used by the mining industry to make air velocity measurements in mine entries. Although the instrument has no appreciable influence on the airstream in mine entries, especially since the cross-sectional area of an entry is much larger than the cross-section of the anemometer, correction or method factors are used to correct the center line anemometer velocity to average velocity. This adjustment is made because the air velocity in a mine entry is highest in the center and lower at the sides. Anemometers can be used to measure gas flow from small diameter pipe outlets; however, since the instrument diameter is much larger than one-sixth of the pipe diameter, it will influence the air-stream from these small outlets. Resulting velocity measurements are erroneously high by as much as 30 percent. Method factors must be applied to such anemometer measurements taken at pipe outlets. Through a research investigation the Bureau of Mines established a set of method factors for center-line anemometer readings taken at the discharge end of 4-to 8-inch diameter pipes. These method factors were combined with method factors which were developed by the National Coal Board of Great Britain for 12-to 30-inch diameter pipes. The anemometer was mounted on the end of a short rod and held against the pipe for support except on the 4-inch pipe where the instrument was started and stopped remotely to prevent hand interference with the air-stream during measurements. Method factors were determined by comparing the anemometer measurements at the pipe outlet to the true average airflow which was simultaneously determined upstream by venturi measurements. Consequently, a method factor is nothing more than the ratio of the true velocity to an anemometer measurement.

Jan 1, 1987

By James Noll, Sam Janisko

Underground miners are exposed to some of the highest levels of diesel particulate matter (DPM) in the United States. Therefore, it is important to monitor the exposure of miners to DPM, but it can be difficult because of the complex composition of DPM and the number of interferences. Currently, elemental carbon (EC) is used as a surrogate because it makes up a significant fraction of the DPM and is not affected by interferences. Standard measurement methods for EC can be time consuming and only record end of shift results. In this research, a laser absorption technique that enables one to measure EC concentration in near real time was shown to be a beneficial tool. The real time data showed that the fresh air being drawn into a stone mine was not properly reaching the working area and needed to be redirected to decrease DPM concentrations. The real time data also provided a more accurate efficiency ofan environmental cab compared to just using the standard method by detecting the opening of the cab's window and door. The EC optical monitor was also worn by researchers in a mine to show how it can give not only the average concentration for the shift but also reveal when and where a miner is exposed to DPM. Keywords: Laser absorption, diesel, elemental carbon, mining, exposure

By Sean Gallagher, Thomas G. Bobick, William S. Marras

Twelve healthy, experienced underground cool miners performed lifting capacity tests in stooped and kneeling postures using a modified psychophysical procedure. Subjects adjusted weight in a lifting box to the maximum they could handle without undue fatigue in an asymmetric lifting task. Lifting periods were 20 min in duration and the frequency was 10 lifts/min. Tests were performed under a 48-in. roof that restricted the subject&apos;s posture. Psychophysical. physiological, and biomechanical dependent measures included the maximum acceptable weight of lift (MAWL), heart rate (HR), rate of oxygen consumption (VO2), ventilation volume rate (VF), respiratory exchange ratio (R), and integrated electromyography (EMG) of eight trunk muscles. Results indicated that the MAWL was significantly lower when kneeling than when stooped (p < 0.05), Furthermore, metabolic demands were greater in terms of HR (p < 0.005) mid VO2 (p < 0.05) when kneeling. Left and tight erectores spinae muscles exhibited increased EMG activity- in the kneeling posture (p < 0.001). It was concluded that psychophysical lifting capacity is decreased, while the metabolic stress and internal load on the spine are increased, in the kneeling posture. Results of this Bureau of Mines study indicate that it may be advisable to reduce the weight of materials that are handled repetitively in the kneeling posture.

By Walter W. Kaufman

This report summarizes a study conducted to determine the state of the art of various rock removal systems and their capabilities. The objective of the study was to determine if currently manufactured equipment can adequately accomplish rock removal in surface mine reclamation applications. Evaluations of state reclamation regulations, with regard to topsoil rock content, were made to determine the rock removal requirements. The major categories of equipment studied are rock pickers and rock rakes. The impact of rock removal implementation on the reclamation operations is discussed in detail.

Jan 1, 1979

By Rolland L. Blake

The Bureau of Mines investigated the mineralogy, tonnage, and beneficiating characteristics of oxidized (nonmagnetic) taconite iron resources of the Western Mesabi Range as part of its program to insure adequate future domestic mineral supplies. Magnetic taconite currently provides about 95 pct of Mesabi production, but the large tonnages of oxidized taconite between the magnetic deposits will be needed to help meet future domestic demand for iron ore. Three bulk samples that represent large tonnages from the Western Mesabi Range were selected to determine their mineral composition and liberation by light optical microscopy and to test their beneficiating response. This report describes the mineralogy and liberation characteristics of the three samples of the Biwabik Iron-Formation for 26.5 mi (42.7 kID) from Keewatin to Grand Rapids, MN. (Details of response to beneficia-tion were reported previously.) The samples represent mostly material from the Lower Cherty Member of the Biwabik-Iron Formation, although one sample included some Upper Cherty Member. Minerals of all three samples were quartz (chert), hematite, goethite, and minor to trace amounts of magnetite, iron carbonate, and iron silicates. It was concluded that the oxidized taconites of the Western Mesabi Range represent a subeconomic indicated resource that can be selectively mined and beneficiated as a future large source of iron feed for steelmaking.

Jan 1, 1983

By James Westfield

A brief résumé follows of activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code fur Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous -coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reportin; to the Coal Mines Administrator any violations of the Federal Minis Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority under Executive Order 9728 was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1960

By Susan B. Robertson, Gregory E. Hinshaw

Many injuries are caused each year by rock falls in coal mines. Most of these injuries are not caused by major roof collapses, but from falls of smaller rocks from the immediate top or roof skin. Various surface controls are used in mines to control this surface rock. One that has been found to be very effective is roof screening. Depending on the size of the screen, roof coverage approaching 100%can be achieved. Many mines are reluctant to use screen for primary skin control because of additional costs of time and materials, but others are having great success at both controlling costs and surface rock. Data is presented from two mines that show a dramatic reduction in roof skin injuries when screening is used. Much of this success is due to innovations in roof bolting machines. Four case studies of roof screen experience are presented along with associated costs of materials, impact on bolting advance rates, and potential ergonomic risks. The effects of roof screening on skin control and safety are also included. Finally, this paper will provide information about features of different roof bolting machines that affect production and safety.

By C. T. Anderson

In July 1947, the U. S. Bureau of Mines, in cooperation with the Air Materiel Command, started an investigation of zirconium alloys with the object of determining the suitability of such alloys for high-temperature applications. This report covers the preliminary study of about 25 zirconium-rich alloy systems with respect to preparation, fabrication, tensile properties, metallographic structures; constitution, and heat resistance. Obviously, each system could not be investigated thoroughly, and this publication can be regarded only as a first approach. The more promising individual alloy systems will be studied in greater detail and reported in subsequent publications. The study of zirconium alloys on such a scale has been made possible by the U.S. Bureau of Mines developments in the past 5 years On producing zirconium metal. This basic process is similar to that developed by Kroll for producing ductile titanium metal and consists essentially of reducing zirconium chloride by means of molten magnesium. The Northwest Electrodevelopment Laboratory at Albany, Oreg., has produced several thousand pounds of ductile metal in this manner and has a pilot plant producing over 300 pounds of metal per week. Alloys were prepared by melting Bureau of Mines zirconium and the best available grade of alloying element in graphite, with suitable provisions for preventing oxidation. The ingots were quartered longitudinally and sheath-swaged at 850° c. to 3/8-inch diameter rod. Two of those rods were send to Wright Field for room-temperature and 1,200° F. tensile properties. The remaining two sections were used for metallographic, hardness, heat-treatment, and heat-resistance studies. The salient features of this investigation are summarized in table 1.

Jan 1, 1950

By M. Orchin

THIS PAPER is concerned with two aspects of the behavior of coal: (1) Dispersion by solvents atmospheric pressure and high temperature and (2) the destruction and regeneration of the coking properties of coal. Several pure polycyclic compounds and a coal-tar fraction were found to extract 95 percent of the organic material of a bituminous coal. About 20 percent of the extract was soluble in benzene, and this fraction contained the ?coking principle? of the coal. From an extensive chemical spectroscopic, and x-ray study of the benzene-soluble material, some conclusions could be drawn concerning the composition and structure of this fraction of coal. A possible commercial application of the extraction technique is in the preparation of low-ash carbonaceous material for the manufacture of electrode carbon.

Jan 1, 1951

By John G. Parker

Many of the so-called minor metals are derived as byproducts from the processing of lead and zinc concentrates in which they occur as minor constituents. Concentrates from some lead-zinc mineral deposits are more enriched in metals such as cadmium, arsenic, bismuth, silver, and selenium than are others, and these sources offer a continuing, assured supply of certain of these metals. Despite the age of the data collected, the Bureau of Mines feels it to be highly desirable to publish due to its relevance to the objective of the study which was to ascertain the flow of minor metals from certain smelter feeds Efforts to trace these metals through the complicated lead and zinc processing steps included trying to ascertain losses and mode of loss of these metals. Losses of some metals in processing may be surmised as occurring in gaseous and other emissions, or possibly in slags and residues.

Jan 1, 1979

By Laurence F. Kelley

This paper is one of a series being prepared by the United States Bureau of Mines on shaft-sinking methods and costs at individual operations in various mining districts of the United States. The methods and costs described herein are those of The Consolidation Coal Co. at one of its operations in the Tug River district, McDowell County, W. Va. ACKNOWLEDGMENT The author is indebted to Frank R. Lyon, vice-president, Thos. G. Fear, general manager of operations, and Chas. Enzian, chief engineer, of The Consolidation Coal Co., for valuable assistance and collaboration in the preparation of this paper. W. A. Cole, manager of the E. J. Longyear Development Co. furnished valuable data on methods and performance averages.

Jan 1, 1932

By Albert L. Toenges

The purpose of this paper is to describe some of the methods and practices of mining coal mechanically where more than one shift is worked, with the view of determining the advantages and disadvantages of various types of equipment and mining systems now in use. This paper is in the nature of a progress report, and, as the number of mines discussed in it is limited, the conclusions drawn in the comparison of various systems are not final but may be revised after subsequent investigations. Physical conditions vary in different and in the same mining districts and determine, more

Jan 1, 1938

By R. R. Lowery

The Bureau of Mines developed hypereutectic aluminum-silicon alloys which 11.7.d better mechanical properties than the unmodified hypereutectic alloy. A commercial aluminum-20 weight-percent silicon LIr alloy was selected as a ary base for improvement. The primary silicon. grains were reduced from ASTM 4-5 to ASTM 8.5 by the use of phosphorus and phosphorus compounds. The remaining eutectic matrix was refined by sodium metal additions of 0.2 weight-percent. Solid solution strengthening of the alpha aluminum was obtained by adding 2 percent copper and 0.5 percent magnesium. Also, 1 percent nickel was added to harden the alloy. Optimum thermal treatment consisted of a solution treatment for 10 hour:, at 480° C with hot water quench, followed by aging for 6 hours at 175° C. The final alloy exhibited a Rockwell B hardness of 75 ±2 in the heat-treated condition. The ultimate tensile strength was 39,5O0 psi with no recordable elongation. The coefficient of linear thermal expansion was 20.4 x 10-6 per °C in the temperature range 20° to 300° C. No wear resistance data were collected.

Jan 1, 1966

By Daniel E. Sullivan

This Bureau of Mines publication examines the potential impact on minerals of the tariff and nontariff agreements that resulted from the Tokyo Round of the Multilateral Trade Negotiations, which were conducted under the auspices of the General Agreement on Tariffs and Trade. These agreements will affect minerals by reducing tariff levels and by changing rules by which they are traded internationally.

Jan 1, 1981

By D. K. Deardorff, Laurance L. Oden, H. Kato, M. I. Copeland

The equilibrium relationship of hafnium and tantalum was studied to facilitate alloy and property investigations . The data obtained are presented graphically as the equilibrium diagram . Alloys were prepared from high - purity components by nonconsumabletungsten- electrode arc melting . Data for the equilibrium diagram were obtained by optical pyrometry , metallography , X- ray diffraction of heat treated specimens , X- ray diffraction using a high- temperature camera , and differential thermal analysis . During the investigations , a casting apparatus was constructed , and the existing melting - point apparatus was improved . The bcc allotrope of hafnium forms a continuous series of solid solutions , called beta , with tantalum which exhibit a minimum melting point at 20 wt pct tantalum and 2,110 ° C. At 24 wt pct tantalum and 1,050 ° C , hafnium- rich beta decomposes in a monotectoid reaction to yield alpha and tantalum- rich beta . The monotectoid isotherm extends from 5.5 to 60 wt pct tantalum . The twophase region , in which hafnium- rich and tantalum- rich beta solid solutions are immiscible , rises to a maximum temperature of 1,265 ° C at 38 wt pct tantalum . The solubility of hafnium in tantalum decreases from 40 wt pct at the monotectoid temperature to 20 wt pct at 750 ° C.

Jan 1, 1964

By C. M. Harrer

This paper describes the location and general features of iron occurrences in Colorado. Most of the deposits were examined; many are in forested and mountainous areas at altitudes of 5,000 to 13,700 feet. Iron is known to occur in 30 counties of western Colorado. Transporting the ore to market is a handicapping economic factor involving long truck and railroad hauls; the nearest purchaser of smelting ores is the Colorado Fuel and Iron Corp., at Pueblo, Colo. When the ore can be sold locally for special purposes and at higher prices than can be obtained at iron smelters, small-scale operations can supply that market.

Jan 1, 1959

By John E. Trombly

System objectives and design criteria for an in-mine ULF radio paging system are discussed Coding formats, frequency and bandwidth selection criteria leading to the system design are discussed. The prototype call alert transmitter and pocket page receiver is functionally described. The report includes circuit descriptions, schematics, parts lists, printed circuit fabrication and assembly drawings. The report concludes with an estimate of the manufacturing cost for each assembly.

Jan 1, 2011

By Thys B. Johnson

The mine system analysis and evaluation study presented in this report was part of the U. S. Bureau of Nines&apos; Tertiary channel project conducted under the Heavy Metals program. The Badger Hill pit, located on the west end of the San Juan Ridge area, near Nevada City, California, was the site of the Bureau&apos;s field work. The objectives of this study were: (1) Determine potential alternative mining systems for some of the large tertiary channel gold-bearing gravel deposits, and (2) Identify areas of technology where further investigation would be merited because of their potential inclusion in a mining system for such deposits, The study involved the development of a mineralized block inventory, an economic block inventory, determination of optimum ultimate mining limits and a preliminary economic mining system evaluation. Computer programs were developed and utilized for each of the study phases stated above. The sampling program conducted at Badger Hill by the Bureau Delineation Group together with confidential drill hole data provided by the San Juan Gold Co. formed the basic gold values and distribution information from which a deposit model was developed. The deposit was divided into minable block units and net economic values were assigned to each block for various configurations of both open-pit and underground mining methods based on cost and performance data provided by the various Bureau of Mines Research Centers. A number of controllable variables such as: (1) Mining method (open-pit and underground), (2) depth of mining cut, (3) production rate and (4) equipment type and capacity were evaluated. The prime measures of effectiveness on which the mining systems where judged were discounted cash flow rate of return and maximum utilization of natural resources. The analysis showed that underground mining of the Six-Mile Tertiary channel gold-bearing gravel deposit under consideration was uneconomical and did not permit maximum recovery of the resources within the channel. It was also apparent that mining the Six-Mile Deposit for gold alone is uneconomical or at best marginal at a gold price less than $80 per ounce. The analysis showed that the potential for an economic mining operation within the Six-Mile Deposit exists when the gravel resources of the channel are considered together with the gold. It was determined that the highest rate of return would be realized with a 20-year open-pit mining operation yielding 745,000 ounces of -gold and 55 million cubic yards of usable gravel.

Jan 1, 2012

By D. Harrington

Part III-B, presented in this circular, completes the series reviewing the literature on effects of breathing dusts with special reference to silicosis; it includes data on the status and cost of compensation for silicosis in the United States and several foreign countries and a summary and general conclusions covering the whole series. Parts I, II, and III-A of the series have been issued as Information Circulars 6935, 6840, 6948 , and 6957; Part I defines and classifies dusts, indicates sources of exposure, and describes the physiological effects of breathing dusts; Part II-A discusses the principal dust factors producing pulmonary pathology and methods of determination of dust in air; Part II-B presents data on the engineering and medical control in the prevention of dust diseases and general recommendations for their control in industry; and Part III-A deals with the economic and legal aspects of dust diseases in industry.

Jan 1, 1936