Search Documents

By Charles C. Boley

High-volatile A bituminous coal from the Allen mine, Las Animas County, Colo., blended with char produced from the same coal yielded accept-able metallurgical coke in a 500-lb movable-wall test oven. Nineteen experimental runs were carried out using several concentration levels of two different chars, 5.6 and 19.6 percent volatile matter, produced by entrainment carbonization of the base coal. With the higher-volatile char, an acceptable coke was produced at a 22.5-percent concentration; the lower-volatile char did not produce an acceptable coke at the concentrations investigated.

Jan 1, 1972

By P. A. Croce

A total of 17 mine gallery fire tests (23 including sub-tests) were completed during this report period (10/1/76 - 11/30/77), directed at identifying a hazardous timber-set fuel-loading in a mine passageway that is otherwise free of combustibles. Results of these initial tests show that the capability of a particular fuel loading for propagating a fire is dependent upon the imposed ventilation air velocity and the ignition intensity, although this dependency needs to be better defined. It is also apparent that care must be taken when relating gallery test fire behavior to actual mine fire behavior, because of the restrictive length of the gallery. Present data indicate that some modification to the instrumentation scheme may be advantageous before proceeding with future tests.

Jan 1, 1978

By J. Roth

The purpose of the present study is to increase the safety of explosive storage. This was accomplished by: a) review of the histories of recent and past magazine explosions to define causes and trends; b) observation of present-day explosive storage conditions and practices at active mines; c) examination of existing Federal regulations on explosive storage to determine whether they address all conceivable safety problems, whether they contain redundant or obsolete standards, and whether their intent is clearly stated; d) recommendation, for safety improvements and for revision and clarification (if necessity) of governmental regulations. Magazine explosions are rare. A recent increase in magazine explosion frequency must be attributed to a large increase in deliberate (criminal or malicious mischief) explosions. Fires of various origins account for the remaining explosions of the past decade. During 1884-1926 several lightning-generated explosions occurred in non-metal magazines, but none recently. It appears that the contents of a well-constructed, metal magazine are immune to direct lightning strikes, regardless of whether the magazine is grounded or not grounded. Grounding a metal magazine cannot be harmful, but it may well be superfluous. Magazines were observed at 34 widely separated mines and storage problems were discussed with personnel at these mines. In general, storage conditions and practices were found to be satisfactory. Usually, only small quantities of explosives are stored on mine property since most explosives are brought in by suppliers when needed. MSHA and BATF standards on explosive storage appear to cover safety aspects adequately. However, certain revisions are recommended to clarify some of these standards and to reduce inconsistencies in their enforcement.

Jan 1, 1983

By Francis X. Cannaday

Equipment and techniques were developed with Bureau of Mines facilities for measurement in the laboratory of sonic shear wave velocity in variously shaped rock specimens in a wide range of sizes. A variety of rock types was tested. The shear wave front is produced by electronically excited, piezo-electric ceramic) disk-shaped transducers. Transmitter and receiver are interchangeable. Special equipment components were Bureau produced; other components were commercially available. The equipment permits quick measurement of shear wave velocity on variously shaped specimens with a minimum of specimen preparation. The technique, under favorable conditions, allows for determination of the moment of arrival of the shear wave when it is superimposed on a weak longitudinal wave.

Jan 1, 1968

By Eric H. Brown

One of the best methods by which the results of accident-prevention work can be measured for any particular period is to keep an accurate record of the accident experience, which may then also be compared with the experience of others. The purpose of this report is to compare records of the salt-mining companies operating in Louisiana, and their assistance in making available their accident records is gratefully acknowledged. PRODUCTION Four companies produce salt in Louisiana -Avery Salt Co., Avery Island; Jefferson Island Salt Mining Co., Jefferson Island; Myles Salt Co., Weeks; and Carey Salt Co., Winnfield. Three of these companies operate within 30 miles of each other in the southern part of the State, and the other operates in the central part.

Jan 1, 1938

By T. G. Donnelly

This final report summarizes the prototype development and testing of an air curtain respirotory protective device under Bureau of Mines Contract HO122087. The air curtain respiratory protective device, as part of a miner?s hat, provides protection for the underground mining machine operator against inhalation of dangerous amounts of respirable coal dust. Major components of the air curtain respiratory protective device are: 1) a modified miner hat incorporating an air curtain jet manifold from which the protective air curtain emanates, 2) a motor blower which supplies the air for the air curtain, 3) a filter element to remove the particulate material from the air used for the air curtain, and 4) the hoses and coupling used to duct the filtered air from the motor blower to the modified miner's hat.

Jan 1, 1973

By G. R. Moulder

A device was developed that measures dynamic stress (ultrasonic energy) transfer through installed rock bolts, a measure that is directly proportional to the degree of grout bonding of the bolt to the mine roof structure and thus the ability of the bolt to bear static stress. The rock bolt bond tester (RBBT) is a hand-held portable device that shows three ranges of bolt bond condition; i.e., one-third (Bad bond), two-thirds (marginal), or fully bonded. These are shown respectively by a red, yellow, or green light that displays for 4 s. RBBT performance was verified with 2 1/2-to 8-ft bolts installed in various types 0f mine roof structures (sands tone, shale, and boney coal-mud), and 15 now being tested by the Bureau of Mines in mines across the United States. The unit is about the size of a five-battery flashlight and contains the transducer electronics, and battery pack. The RBBT is designed for extreme ease of operation, requiring only manual contact with the bolt and signal read-out. The batteries are rechargeable and the package is designed for durability in a mine environment.

Jan 1, 1983

By R. H. Sprute

This report describes Bureau of Mines laboratory test results in electrokinetic dewatering and consolidation of metal-mine tailings. Tailings were placed in 0.3-cubic-foot Plexiglass models, and dc potential was applied until dewatering ceased. Time-oriented measurements of water removal, changes in resistivity, and power consumption were recorded during the dewatering process. Dewatered material was tested for moisture content and density. Equipment and procedures were developed to optimize the method for unclassified mill tailings from a particular mine in the Coeur d'Alene, Idaho, district. Results indicate the method to be highly effective in dewatering and consolidating this material.

Jan 1, 1974

This study estimates costs of producing bituminous coal and lignite by strip-mining methods in 12 hypothetical mines. Basic costs are developed by geographic area, rank of coal, and output capacity. Seam thickness and depth and type of overburden are considered typical for the area in which the hypothetical mine would be located. The cost analyses are based on the use of new equipment, the prevailing union wage scales, and the payment of all miscellaneous costs including royalties, contributions to the miners' welfare fund, and license and permit fees. All model mines are considered to have a life span of 20 years. Capital costs of bituminous strip mines with a capacity of 1 million tons per year range from $12.7 million in the Appalachian region to $16.0 million in the Interior province. The corresponding selling price, assuming a discounted cash flow return of 12 percent on investment, is $5.40 and $6.95 per ton, respectively. For bituminous coal strip mines producing 3 million tons annually, a capital investment of $24.9 million will render a selling price of, $3.46 per ton in the Interior province, whereas a similar mine in the Appalachian region requires a capital investment of $28.0 million to produce coal selling for $4.01 per ton. Subbituminous strip mines of 5 million tons of output per year range in capital costs from $28.7 million in the Southwest to $13.9 million in Wyoming and Montana. Coal produced in the Southwest would sell for $3.03 per ton, while coal from Wyoming and Montana would sell for $1.83 and $1.64 per ton, respectively. The capital costs for the strip mining of lignite range from $6.4 million for an output capacity of 1 million tons annually to $20.7 million for an annual capacity of 5 million tons. The corresponding selling prices of $3.01 and $2.12 per ton, respectively, Indicate the advantages of a large-capacity strip mine.

Jan 1, 1972

By Michael S. Miller

In 1984, at the request of Bureau of Land Management, the Bureau of Mines studied 8,500 acres of the 20,250-acre Seven Blackfoot Wilderness Study Area (WSA) consisting of all 3,950 acres of MT-024-657A and 4,550 acres of the 4,850 acre MT-024-657B in order to evaluate the mineral resources. Within this report these 8,500 acres are referred to as the study area. Located about 30 miles northwest of Jordan, MT, the study area is underlain by outcrops of Quaternary alluvium and Cretaceous to Paleocene sandstones, shales, clays, and coal. No mines or prospects were found in the study area. Except for some current interest in petroleum and natural gas, there has been no mineral exploration activity in the study area. The study area contains subeconomic clay, placer gold, and coal. Land within the study area is leased or under lease application for oil and gas.

Jan 1, 1986

By F. A. Jones

Increased mechanization .of coal mines has emphasized the need for study of actual power requirements of the various machines employed in the production of coal and losses in the distribution of power to these machines. These studies are being made in order that hazards, excessive use of power, and high maintenance cost of equipment resulting from these losses may be analyzed and eliminated where possible. Research on the use of electric power in-coal mines was suggested by the Advisory Committee of the Bureau of Mines in 1937, and it was decided to begin with a study of individual machines of various types under operating conditions in modern coal mines. The transmission of power, particularly line losses and inadequate return circuits, should be a part of the investigation. This report presents some of the data of an initial study in commercial mines. ACKNOWLEDGMENTS The superintendents, engineers, and other officials of the two mines studied cooperated fully and aided in setting up and transporting the test equipment, giving such information as was requested.

Jan 1, 1942

By S. P. Sandoval

Previous research by the U.S. Bureau of Mines demonstrated that nonionic surfactants increased the leaching rate of copper in the flask leaching of chalcopyrite with ferric sulfate if sufficient ferric sulfate was present. This research was continued by the Bureau in Part 2 to further explore the application of nonionic surfactants to the dump leaching of chalcopyrite. A polyoxyethylene lauryl ether was selected as the superior nonionic surfactant tested at 25° and 50° C. The addition of the surfactant increased copper leaching by 116 pct at 25° C and 1.0 pct solids and by 61 pct at 50° C and 0.5 pct solids at Fe 3+ concentrations greater than 1 g/L. At 0.1.0 g/L Fe 3+ and below, the addition of the surfactant produced as much as a 35 pct decrease in leaching. Each of the nonionic surfactants studied was found to be heavily adsorbed by a typical chalcopyrite ore, which poses a serious barrier to the application of nonionic surfactants in an actual chalcopyrite dump.

Jan 1, 2010

By A. Wahab Khair

"This paper presents an analysis of fracture mechanisms in coal subjected to bi-axial state of stresses, indentation of laterally confined coal specimen. Coal specimens were loaded to failure by the straight wedge indenters at various lateral confinement pressures. Strain distribution and acoustic emission characteristics of coal specimens under stress were recorded. The influence lines of vertical forces acting on the horizontal straight boundary of the coal specimen for each type of wedge indenter have been established using holographic interferometry technique. The effects of wedge indenter angle, confinement pressure, and coal anisotropy on fracture types, failure modes, and post-failure conditions were studied. The results indicated that combined application of holographic interferometry and acoustic emission monitoring techniques is not only suitable ·for studying deformability of heterogeneous and microscopically discontinuous material under stress but it also enhances the mode of fracture during the post failure stage. INTRODUCTIONOne of the relevant processes in the coal cutting technology is the application of indentation theories. Since most cutting tools in the coal industry are wedge shaped most of the indentation research is found for a wedge shaped tool.A wide range of behavior is found in different rocks subjected to the wedge penetration. A rock which is elastic brittle at standard pressure might become elastic plastic at high confining pressure (Gnirk and Cheatham, 1963). It was also observed that some rocks will merely be crushed and indented by a wedge whereas others will crack and form chips, furthermore the existence or non-existence of chips depends mostly on the geometry of the indenter, type of rock and the depth of penetration (Evans and Murrel, 1958). However, coal cutting technology is mostly explained by models which use rigid wedge to penetrate into a brittle material in which both crushing and chipping will occur (Evans and Murrel, 1958, 1962)."

Jan 1, 1988

By F. A. Jones

Increased mechanization .of coal mines has emphasized the need for study of actual power requirements of the various machines employed in the production of coal and losses in the distribution of power to these machines. These studies are being made in order that hazards, excessive use of power, and high maintenance cost of equipment resulting from these losses may be analyzed and eliminated where possible. Research on the use of electric power in-coal mines was suggested by the Advisory Committee of the Bureau of Mines in 1937, and it was decided to begin with a study of individual machines of various types under operating conditions in modern coal mines. The transmission of power, particularly line losses and inadequate return circuits, should be a part of the investigation. This report presents some of the data of an initial study in commercial mines. ACKNOWLEDGMENTS The superintendents, engineers, and other officials of the two mines studied cooperated fully and aided in setting up and transporting the test equipment, giving such information as was requested.

Jan 1, 1942

By John Paul Gries

During World. War II, when the curtailment of imports led to an unprecedented demand for domestic mica, beryl, spodumene, and other pegmatite minerals, the Bureau of Mines and the Geological Survey entered upon a program designed to expedite mining of these minerals from the Black Hills area of South Dakota. The program involved napping, sampling, and drilling of many pegmatite dikes in the southern portion of the Black Hills and beneficiation conducted in the field and in the Bureau of Mines laboratories at Rapid City, S. Dak., Rolla, Mo., Salt Lake City, Utah, and College Park, Md. This report describes the occurrence and sampling of the Beecher No. 2 pegmatite, which was investigated as part of the general pegmatite study in South Dakota. Investigation of the Beecher No. 2 pegmatite was started on November 20, 1943, and terminated in the spring of 1944. During this period, the Bureau of Mines took a series of trench samples across the pegmatite at the surface for grain-count studies and chemical analyses. The Geological Survey mapped the geology of the deposit after it was exposed by trenching and stripping.

Jan 1, 1950

By Michael D. Balen

The U.S. Bureau of Mines (Bureau) is currently conducting a four-year study to assess the mineral resources and the mineral development potential of the 5.7 million acre Valdez Creek Mining District (VCMD) located in southcentral Alaska. The VCMD study is part of the Bureau's ongoing statewide mining district evaluation program. This report is a summary of the 1988 field work. The field work involved collection of reconnaissance placer and rock samples, and also involved sampling and examination of the mines, prospects, and mineral occurrences which were identified by literature research of the geology, exploration history, and mining history of the district. During the 1988 field season, Bureau personnel spent a total of 11 weeks in the field, collected 1,006 rock and placer samples, and located, mapped, and sampled 106 of the known mineral occurrences. The Bureau has visited 243 of the 250 known mineral occurrences during the course of the VCMD project. Reconnaissance sampling for placer occurrences resulted in the identification of 4 previously unreported gold placer occurrences, and identification of 5 occurrences that contain detectable levels of platinum or palladium. Reconnaissance sampling for lode sources of base and precious metals resulted in the identification of 5 new Lode gold-silver occurrences, identification of 2 occurrences that contain elevated quantities of chromium, cobalt, nickel, palladium, and platinum, and identification of one occurrence that contains elevated quantities of copper, molybdenum, anti zinc.

Jan 1, 2011

By S. J. Rodgers

This report presents guidelines on methods of dust control in conventional coal mining operations. The normal mining cycle and equipment used in a room and pillar conventional section are described. Main ventilation, section ventilation and face ventilation are discussed in detail. Proper installation of line brattice, maintenance of proper air flows at the face and split ventilation are stressed. The effects of maintaining the end of the line brattice near the face are described. The advantages and disadvantages of blowing and exhausting face ventilation are presented. The use of water sprays on cutter bars and loading machines is described. The design of a nonclogging water spray system developed under a Bureau of Mines contract is presented. Other methods of reducing dust exposure are discussed and include alternative procedures for shot firing and administrative controls.

Jan 1, 1983

By Andrew K. C. Wong

Hydraulic transport has been considered as one of the most economical methods in transferring granular materials over relatively long distances. In the natural world, it is used to transport basic material required for the support of life; in industry, it is a method widely adopted for handling materials. But the phenomena of hydraulic transport has not yet been thoroughly understood. As most of them are conditioned by a number of hydraulic and mechanical parameters, of which the basic relationships are not fully known, the traditional approach in relating these parameters to the energy requirement is purely empirical in nature. Empirical formulas, such as that proposed by Durand, (1) only give satisfactory results over a selected range of (particle size)/(pipe diameter) ratios and slurry concentration. When the case is more complicated or when new situations arise, the empirical formulas fail to give good predictory results. In fact, most of these formulas are based upon dimensional analysis, where the underlying physical interaction is not explicitly considered. Apart from the loosely related, non-dimensional groups incorporated in the formulas, there is practically no analytical means for modifying the formula so as to enable it to cope with more complex real physical situations. Although it seems quite remote that a complete rigorous solution to this highly complex problem could be generated in the near future, it is generally recognized (2, 3) that research in this area should be directed to more comprehensive studies of the obscure phenomena. In fact, there are a good number of very basic problems such as the effects of gradation and concentration of particles upon

Jan 1, 1972

By Roy C. Bartholomae

This Bureau of Mines report presents the results of a laboratory investigation of coal cutting mechanics and noise. These experiments were performed using linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts was ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to formulate analytical models of the coal cutting forces and noise. The analytical model for coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator's position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as provide benefits to other important areas of health and safety in underground mining.

Jan 1, 1983

By T. A. Sullivan

The work described in this report was undertaken to evaluate and develop techniques for determining the oxygen content of titanium and titanium alloys. Early investigations of volatilization techniques involving halogenation were unsuccessful. Later efforts were concentrated on evaluating vacuum fusion and inert-gas fusion techniques. Two vacuum fusion methods and an inert-gas fusion method were found to be satisfactory in the 0.02 to 1.00 pct., oxygen range. These methods are described in detail. The coefficient of variation by any of the three methods is approximately 5 pct, While the main portion of this paper is devoted to the vacuum and inert-gas fusion methods, a resume of other suggested methods for analyzing titanium for oxygen also is given. INTRODUCTION The Federal Bureau of Nines has conducted research on titanium metal since 1938. This research included development of the Kroll process for the production of titanium (2)4, various sodium reduction processes for making titanium metal and lower valent titanium chloride-sodium chloride mixtures (17), and a fused salt electrolytic process for Me production of high-purity titanium metal and the recovery of titanium by electrorefining from off-grade materials (20).

Jan 1, 1961