Search Documents

By M. Clair Smith

This report is one of a series being prepared by the Bureau of Mines on exploration, development, mining methods, and costs at various open-pit mines in the United States. These reports have been prepared in cooperation with various mining companies. A similar program, conducted from 1928 to 1939, was generally conceded to have contributed to improving the efficiency of mining operations. The purpose of these reports is to promote development and conservation of our mineral resources by disseminating technological information on mining methods and practices. This report describes exploration, development, equipment, and mining by open-pit methods of the remainder of an ore body that had been previously worked by underground methods. The Tripp pit of the Consolidated Coppermines Corp. is located at Kimberly, Nev., a small mining company town having an elevation of 7,250 feet, 9 miles by road west of Ely, Nev. (fig. 1). The pit extends over the area formerly mined by underground methods from the Morris and Brooks shafts.

Jan 1, 1962

By Forrest T. Moyer

INJURY experience and employment data are presented in this (chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron-blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume III. The 1963 figures are preliminary and are subject to revision. METAL MINES Preliminary estimates for the metal-mining industry of a combined fatal and nonfatal injury-frequency rate of 32.34 per million man-hours in 1963 indicate only a slight change from the rate of 32.00 in 1962. Metal operations had 41 fatal and 3,110 nonfatal injuries during 1963.

Jan 1, 1964

By G. G. Morgis

In carrying out the provisions as set forth by an Act of Congress (36 Stat. 369) approved May 16, 1910, effective July 1, 1910, and the amended Act of February 25, 1913, (37 Stat. 681), the Bureau of Mines, among other activities, conducts inquiries and scientific and technologic investigations concerning mining with a view to improving health conditions and increasing safety and disseminates the general information gained by these studies. Through the medium of these publications, the causes as well as the methods that have been found most satisfactory in combating undesirable conditions are brought to the attention of the mining industry. This bulletin describes health and safety reports that have been published for the period July 1, 1955, through June 30, 1961. Technical Paper 705 issued in 1948 contains a listing of all Bureau of Mines publications dealing with health and safety in the mineral and allied industries from 1910 through 1946; Bulletin 558 contains a bibliography of such reports that were issued from January 1947 through June 1955.

Jan 1, 1962

By John R. Hoskins

The Bureau of Mines conducted an investigation to more exactly define the influence of some end conditions on the laboratory-determined uniaxial compressive strength of rock samples. Limestone, marble, sandstone, and granite were used to provide a range of specimen modulus of elasticity from 2.7 X 106 psi to 10 x 106 psi. Four variables were studied: Nonparallelism and surface texture of specimen ends were the specimen variables investigated; the end platen size and the adjustable or spherical head friction were the machine variables studied. It was concluded that the loading ends of small laboratory models and samples should be prepared with surface irregularities that do not vary from a plane surface by more than 0.001 inch. It was also concluded that nonparallelism of the specimen ends should not exceed 8 minutes for a rigid head load or 15 minutes for an adjusting head load. The measured compressive strength of specimens prepared with these tolerances will be statistically the same with any diameter or thickness of platen and any degree of head friction if initial alinement of the specimen is assured.

Jan 1, 1968

By B. W. Madsen

To help maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines developed a mathematical model that describes acidic ferric sulfate leaching of copper from sulfide ores. The leaching model can aid in maximizing minerals and metals recovery from primary sources by giving operators and management a better understanding of the copper leaching process. This will aid in improving dump leaching operations. The model is based on a steady-state approximation of the continuity equation for diffusion of ferric ions in the rock pores and the intrinsic leaching kinetics of the various sulfide mineral particles. Ore characteristics included in the model were ore particle-size distribution, particle shape, grade, mineral content, mineral particle size, porosity, and tortuosity. The continuity equation was used with ferric ion concentration gradients and a fixed value for the diffusion coefficient. Except for effective diffusivity, each of these factors was either measured experimentally or estimated from theoretical considerations. The effective diffusivities were determined by fitting calculated leaching curves with experimental leaching data. Vertical variations in leach solution composition and temperature within a dump are not considered in this model. The model accurately predicted copper extractions for several large-scale tests during nearly 500 days of leaching.

Jan 1, 1981

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchange-ability, and speed, it has become even more important. In spite of the supply of other abrasive and hard materials and of ultrasonic, electrospark rued other substitute grinding, methods, world industry seams likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting roes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determined the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has affected substantial savings.]

Jan 1, 1964

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchangeability, and speed, it has become even hors, important in spite of the supply of other abrasive and hard materials and of ultrasonic, electrospspark rued other substitute grinding methods world industry seems likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting goes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determine the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has effected substantial savings.]

Jan 1, 1964

By Robert C. Hickman

In its search for strategic minerals, the Bureau of Mines investigated the Rutherford Mine property in Amelia County, Va. The property was visited by F. W. Horton, mining engineer, and Margaret Fuller Boos, mineral technologist, of the Bureau of Mines, in company with Eugene Dawson, of the War Production Board, on July 16-11, 1943. An exploration program by the Bureau was recommended, and work was started on July 28, 1943, and continued until September 16, 1943. A total of 1,250 feet was diamond drilled in 5 holes on the property.

Jan 1, 1950

By James D. Eklund

Towards the goal of improving safety, economy and efficiency of scaling in underground metal/nonmetal mines, Battelle developed a combination prying/hammering scaling tool. A prototype was subjected to limited testing 1) to verify its operational functions and 2) to assess its potential capability in future underground testing.

Jan 1, 1983

By R. H. Oitto

To determine whether reflectors could substitute for the trip lights referred to in the Federal Mine Safety Code, the Bureau of Mines studied trip safety devices under simulated haulageway conditions. The noticeability of reflectors compared with trip lights and fluorescent panels was evaluated from distances of up to 850 feet with light source intensities of up to 1-6 foot-candles (ft c). Reflectors tested consisted of a reflective lens in a holder secured to a frame that can be attached to a trip. Reflectors were found to be suitable for use as a trip safety device. In fact, for the conditions in many underground haulageways some reflectors would be more effective than a permissible trip light.

Jan 1, 1968

By Fred D. DeVaney, C. W. Ambler

"Copper sulphate is a common flotation reagent for blende ores. Metallic iron also is present in the mill circuit, and a reaction between the iron and the salt would be in accord with well-known chemistry. The abundance of metallic iron in a flotation feed may be noted by even perfunctory examination. First of all the mine contributes metallic iron, then the coarse-crushing machines add their share, and finally the fine-grinding medium its portion. If the grinding is with cast-iron balls the amount of metallics is greater than when steel is used. Thus it is that much more metallic iron is present than would be indicated by noting the ball consumption. An estimate that the total amount of metallics is twice that supplied by the balls and liners might not be far amiss.That copper sulphate plates out on iron in an acid solution is well known, but since flotation is practiced commonly in solutions where acid has not been added this reaction has not been given sufficient thought.This problem has been the basis of a study undertaken jointly by the Mississippi Valley Station of the United States Bureau of Mines and the Missouri School of Mines and Metallurgy, at Rolla, Missouri. Its importance may be understood better when the tonnage of zinc ores now being treated by flotation in this country is considered. According to Gaudin4 5,536,244 tons of zinc or were treated by flotation during 1927. In these operations copper sulphate was employed as an activating agent; the amount per ton averaged 0.81 pound for straight sulphide zinc ores and 1.16 pounds for complex ores. Since such large quantities of zinc ore are treated by flotation and since metallic iron is always present, the importance of studying their reactions on each other and the effect of their reaction"

Dec 1, 1929

By Fred P. Giese

Southeastern reserves of titanium ores are large, widespread, and ample for anticipated demand. The leading titanium industries are mining and beneficiating sand deposits, principally in Florida, and manufacturing titanium pigments. Most of the mineral output is consumed by the producers themselves. In 1962, 20 percent of the national pigment capacity was in the Southeast.

Jan 1, 1964

By Dana C. Reinke

A job analysis is a written list of the tasks associated with doing a particular job. In drilling, describing the steps associated with adding rod to the drill steel would be an example of a task associated with the job. How to hammer casing or fish a lost drill bit out of a hole would also be job tasks. Develop a written list of job tasks. Ask drillers in your company if the tasks listed are correct and accurately reflect how to perform the job. While each driller may do the job a little differently, some tried?and?true methods are required to perform certain tasks safely and correctly. You may find a separate analysis is needed for different drilling jobs (e.g., a residential well or a monitoring well). Also remember to include the tasks of both the helper and the driller.

Jan 1, 2005

By R. W. Stahl

Gas accumulation and dust suspension are the major safety hazards in coal stockpiling and reclaiming operations. This report presents a schedule of safety precautions and plant design features devised by the Bureau of Mines to reduce danger from these and other sources.

Jan 1, 1965

By J. D. Dixon

This Bureau of Mines report describes a technique for determining the confining pressures that must be provided for stabilizing underground openings in incompetent rock. The technique is adapted for use with a nonlinear finite-element computer code, NONSAP, to obtain stabilization pressures for linear or nonlinear stress distributions in the rock media around the excavation. This analysis permits a point-wise calculation of active rock pressures that depend on the values of shear stress and strength along the excavation surface. The approach is applied to the solution of several sample problems. The results show that both the magnitude and the distribution of stabilizing confining pressures are significantly influenced by rock and joint strengths, joint orientation, and biaxial nature of the load field.

Jan 1, 1976

By J. T. Popp

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con¬tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By R. D. Berkenkotter

Titanium and iron assays obtained from cores of three diamond-drill holes from the Cebolla Creek titaniferous iron deposit were evaluated by statistical techniques to obtain information concerning the mineral characteristics of the deposit and to make a preliminary determination of sampling requirements for the deposit. A range of sample volumes representing sizes from one-sixth NX core 2 feet in length through full NX core 10 feet in length were prepared by split-ting the NX core with a diamond saw and combining pulverized splits. Results indicate the existence of at least two statistical populations having different average grades of iron and titanium. Each has an assay frequency distribution that is not normal but is highly peaked (leptokurtic). Frequency distributions of assays from specific altered zones of the drill holes appear to be normally distributed. Increasing the cross-sectional area of the sample unit to change assay volume did not result in significant changes either in assay values or the resulting frequency distributions of assays. However, when assay volume is increased by increasing sample interval, the shape of the assay frequency distribution changes, and a normal distribution of assays is approached. Positive correlation exists between titanium and iron assays. The degree of correlation, although very significant, is too low to use for prediction purposes. Although the amount of data from three widely separated drill holes is not sufficient to establish an average grade for this large deposit, it indicates a range of expected assay values and provides some information for determining requirements of future sampling for evaluation purposes.

Jan 1, 1963

By L. H. Banning

This investigation was undertaken to obtain basic information necessary for the design and operation of a plant for recovering metallic values from nickeliferous laterite and serpentine of the Philippine Islands. It was divided into three parts: (1) Mineralogical studies and preliminary mineral dressing tests; (2) electric smelting of the ores, upgrading of ferronickel by blowing with oxygen, smelting laterite slag to produce crude iron, and the production of mild steel; and (3) nickel and cobalt recovery from upgraded ferronickel. Results of the investigation indicate that it should be feasible to recover nickel, iron, and possibly cobalt products from the laterite and ferro-nickel from the serpentine. Mineralogical studies were made on representative fractions of the laterite and serpentine tonnage samples and on five selected samples; mineral dressing tests were made only on laterite. The nickel occurs principally associated with hydrous iron oxides and chemically combined with serpentine; garnierite was the only discrete nickel mineral identified, and it was found in a highly decomposed serpentine. The bulk of the cobalt was found in wadlike manganese oxide material. Approximately twice as much chromite was found in the laterite as in the serpentine, By mineral dressing techniques, laterite was separated into two fractions: one fraction contained over 90 percent of the nickel and cobalt, and 83 percent of the iron; the other fraction contained 74 percent of the chromium. A cobalt concentrate (1.1 percent Co) was produced by a scrubbing and sizing procedure.

Jan 1, 1962

By Nicholas Kyriazi, John P. Shubilla

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, has undertaken a study to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), hold up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSRs in the sixth phase of testing from mid-1996 to early 1998. The SCSRs were tested on human subjects and on a breathing and metabolic simulator. These results indicate that most of the apparatus, if they pass their inspection criteria, perform satisfactorily. However, the deployed CSE SR-100s exhibited significantly higher inhaled CO2 levels than new units, as in the previous phase. This will cause higher ventilation rates in most users, which will, in turn, result in higher breathing pressures, possibly causing users to prematurely remove the apparatus. CSE Corp. has developed a noise test that can identify apparatus suffering from chemical-bed degradation causing the early CO2 breakthrough. This test was added to the inspection criteria for the SR-100. In addition, several of the MSA Portal-Packs that passed their inspection criteria were found to have KO2 dust in their mouthpieces. Further investigations by NIOSH and the Mine Safety and Health Administration confirmed these findings, which resulted in the decertification of the apparatus and their removal from service.

Jan 1, 2000

The principle activities of the Explosives Research Laboratory from July 1, 1961 to June 30, 1962, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1962; in general, the research reported in these publications antedates the report period. Part 3 gives the results of an investigation which, although too limited to warrant separate publication, merits presentation in some detail because of current interest in ammonium nitrate-fuel oil compositions.

Jan 1, 1964