Search Documents

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H20) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained,4 but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process 75. In. all of the processes suggested for the recovery of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation. OCCURRENCE OF HALITE IN POLYHALITE A preliminary estimate of the amount of halite associated with typical deposits of polyhalite may be derived from drill cores, although it should be remembered that only 50 or 60 core tests have been made in the many hundreds of square miles of the Permian basin. From a mineralogical study of 41 of these cores, Schaller and Henderson6 state: In many of the sections of core that seem when viewed by the unaided eye to consist essentially of polyhalite, both halite and anhydrite are present in greatly varying quantities - with very minor quantities of clay and magnesite.

Jan 1, 1934

By G. L. Oldright

The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada, Ltd., Trail (Tadanac), British Columbia. Many thanks are due to S. G. Blaylock, vice president and general manager, James Buchanan, smelter superintendent, and George Murray, assistant smelter superintendent, for their broad general policy in permitting these data to be taken and published. life are also grateful for the help given by the staff members stated in Paper XI, Report of Investigations Acknowledgment is given several excerpts from experiments by F. E. Lee, head of the research staff. INTRODUCTION The past reputation of zinc as an ingredient in lead blast furnace slags has been bad. Zinc is thought of as a cause of accretions in the shaft of the blast furnace, of hot tops, of the formation of "zinc mush" in the crucible and forehearth, of lead-rich slags, of viscous slags, and. of low capacity in smelting.

Jan 1, 1934

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0,79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without re-treating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams, Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0.79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without retreating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some -were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams. Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By R. E. Head

This paper embodies the data obtained by a detailed statistical, microscopic analysis of the composite mill feed concentrate, and tailing, from the Magne and Arthur mills of the Utah Conger Co. for 1 month in 1929. It is one of a series of papers by the same authors dealing with the mineralogical characteristics of the ore and concentration products from various well-known plants. The work was done in the cooperative microscopic service laboratory at Salt Lake and represents the results of cooperation between the United States Bureau of Mines, the Utah Copper Co., and the University of Utah.

Jan 1, 1935

By R. E. Head

[This paper embodies the data obtained by a detailed statistical, microscopic analysis of the composite mill feed concentrate, and tailing from the Magne and Arthur mills of the Utah Conger Co. for 1 month in 1929. It is one of a series of papers by the same authors5 dealing with the mineralogical characteristics of the ore and concentration products from various well-known plants. The work was done in the cooperateive microscopic service laboratory at Salt Lake and represents the results of cooperation between the United States Bureau u of Mines, the Utah Copper Co. and the University of Utah.]

Jan 1, 1935

By Scott Turner

The present rapid growth of coal stripping in the United States is a curious reversal of the tendency of mining to proceed from outcrop to depth. A combination of technical and economic factors bas stimulated the use of stripping methods until today many million tons of coal We being recovered by open cuts from sites that an earlier generation of engineers would have passed by as not commercially mineable or, if workable at all, only by underground methods. The total quantity of bituminous coal and lignite mined in the United States by stripping in 1928, the latest year for which detailed figures are available, was 19,789,000 short tons. Of this, 71,000 tons came from small workings not equipped with power shovels and 587,000 tons from properties in which stripping and underground work were carried on at the same mine; but as neither of these types is representative of modern stripping practice, they will be omitted in the discussion that follows. The total from strip pits proper in 1928 was 19,131,000 tons, produced by 176 pits employing 385 steam or electric shovels.3 Figures by States are given in Table 1. Detailed statistics will be found in Economics of Strip Coal Mining; a study by O. E. Kiessling, to be published by the United States Bureau of Mines.

Jan 1, 1930

By J. B. Stott

The performance of an adiabatic calorimeter for measuring heats of oxidation of coal is assessed and suggestions made for its improvement and calibration. The use of magnetic analysers for measuring small oxygen deficiencies in air is described and three different methods of measuring the output for such a meter are characterised. The occurrence of spontaneous heating in an 800 tonne heap of Wyoming coal is briefly described. The major part of the report deals with the oxidation of Pittsburgh seam and Wyoming subbituminous coal and describes an experiment in which 1 tonne of Wyoming coal is stored in a 5 metre long insulated container whilst air was passed through. Temperature rises, rates of oxygen absorption and gas compositions of the air stream were measured. The report relates the results of these-experiments to a theory of spontaneous heating developed by Stott and Quan which stresses the importance of the moisture content of the coal and the relationship between the heat necessary to evaporate this water to the heat available from coal oxidation. The work was carried out over a five month period and the emphasis is on demonstrating the effects of moisture transfer and confirming the theory of Stott and Quan.

Jan 1, 1980

By R. R. Sayers

"An important, function of the U.S. Bureau of Mines is to instruct miners in first aid, and as a means of promoting interest in it first-aid contests are held under the auspices of the Bureau, usually in coop; ration with other interested organizations, especially the American Red Cross, the National Safety Council and various operators' and Miners' associations. It was early found that the method of judging first-aid meets is one of the most vital factors in determining the degree of success of the meet.It may be safely stated that there is no method for the judging of first-aid contests that has proved ideal. A method that would give the most uniform judging would necessitate the rating of each team by the same judge or committee of judges and, in order that a judge may rate a team satisfactorily, he should see that team perform several events and average the ratings. Such a procedure is not practicable where there are many terms entered in the contest, as it would prolong the meet indefinitely. To overcome this objection the method has been tried of assigning separate judges to each team but this brings in a new factor the individuality of the various judges, some of whom rate closely, others loosely. The next development was to average the judging by having the judges rate different teams for each event. This would seem to solve the problem out it has been found, after using the method over a wide area for a considerable period of time, that the differences in the judging are too marked to be at all satisfactory. The next development was to appoint a committee of chief judges three to five in number especially trained and experienced, to aid the individual judges in rating the teams. This method has proved satisfactory at small meets but, as committee must review the work of each judge on each event, it has not been deemed feasible for a large meet."

Nov 1, 1920

By A. J. Farstad

Electromagnetic location tests were conducted by Westinghouse Georesearch Laboratory under the sponsorship of the U. S. Bureau of Mines at the Galena Mine in Northwest Idaho. The objectives of these tests were to evaluate the performance in deep hardrock mines of an electromagnetic location system previously developed for the U. S. Bureau of Mines for use in coal mines. Tests were performed using long wire transmitting antennas as well as horizontal and vertical transmitting loops at depths from 3000 feet to 4300 feet (995 metres to 1311 metres). Surface measurements were made of magnetic field strengths, field strength patterns, and background noise, These measurements were compared with theoretical predictions for a homogeneous ground conductivity consistent with this particular geologic region. The results of the Galena Mine tests show conclusively that light-weight portable electromagnetic transmitters can be effectively utilized to provide uplink communications and location information in deep hardrock mines. Typical metal mines such as Galena utilize deep vertical shafts for mine access and haulage and these shafts produce signal enhancement at the surface from underground electromagnetic transmitters by as much as 30 dB. The results also show that horizontal wire configuration can serve as an effective alternative to the magnetic dipole antenna as a rescue transmitting antennaa and can be used when the required area is not available for deployment of a loop antenna. In spite of the electromagnetic coupling effects observed in the vicinity of the shafts, the location accuracy obtained still provided useful information on the general location of the transmitting sources involved. The horizontal wire location accuracy was within 46 metres, while the vertical magnetic dipole and the horizontal magnetic dipole accuracies were within 152 metres and 110 metres respectively at a 915 metre depth.

Jan 1, 1973

By David E. Nicholson

The Bureau of Mines has constructed a special compression chamber for developing stress-strain relationships of mine backfill and simulating the high compressive ground pressures encountered in underground mines. A one-dimensional, or Earth-Pressure-at-Rest model is proposed for backfills subjected to these pressures. Results of the compression tests performed in the chamber indicate that reliable stress-strain relationships can be developed from these tests. The primary objective of the test series was to evaluate the effectiveness of compaction of common backfills in retarding ground closure. Analysis of the stress-strain data shows an eightfold reduction in relative strain in optimum well-graded, compacted backfills over poorly graded, loose backfill material. Analysis of the one-dimensional compression test data also indicates a significant retardation of transmitted stress in dense compacted samples of backfill and natural sands. Although not fully understood, a deformation mechanism is thought to occur at the intergranular contacts in cyclic fashion causing frictional heat loss and a reduction in transmitted stresses in the densely packed materials. The experimental values of transmitted stress are compared with theoretical values of effective stress calculated from the one-dimensional compression relationships developed by Hendron (4).3 These experimental values of transmitted stress compare very closely with the theoretical values of effective stress.

Jan 1, 1968

By Maurice Deul

This bulletin summarizes the work conducted under the Bureau of Mines methane control research program during the years 1964 to 1979. This research effort was directed toward improving existing methods and developing alternative methods of reducing the explosion hazard during mining. The research was performed in three general areas: (1) basic factors that control the emission of methane into coal mines, (2) methane control during mining, and (3) methane drainage in advance of mining. Topics discussed in this bulletin include the magnitude of the methane problem; the equipment and instruments developed; the geological, chemical and physical parameters that control the movement of methane in coalbeds; the direct method of determining gas content; the estimates of gas content from adsorption data; and methane drainage, through shafts, through horizontal boreholes, through vertical boreholes, or through slant holes. Improvements in ventilation, control of methane in gob areas, and water infusion are also discussed, as is the potential use of coalbed methane as a supplement to natural gas supplies. This bulletin provides a comprehensive source of information on the accomplishments of the Bureau's methane control research program, on the technology developed, and on the direction of further research.

Jan 1, 1986

By Walter C. Lorenz

In connection with its renewed study seeking solutions to problems created by release of acid water from bituminous coal mines, the Bureau of Mines recently surveyed reports already written on the subject. This publication is based on that search. The Problem Poor distribution of water is evident on an ordinary geographic map of the United States. The more abundant supplies of surface water appear to be centered in the northeast, the southeast, and the central humid areas of the country. It is in the midst of this abundant surface water, in the Ohio River Valley, that most of the bituminous coal is mined. Varied industry has located in the valley to use the coal and the river. The coal is a source of power and o raw material. The river provides transportation for raw and finished materials; equally important, it provides the water that is used for cooling and processing in manufacturing. It also serves as a vehicle for the disposal of waste.

Jan 1, 1962

By Forrest T. Moyer

INJURY experience and employment data are presented in this chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume II. The 1962 figures are preliminary summations which are subject to revision. They were compiled from all reports from producers received by the Bureau of Mines through April 15, 1963. The data for metal, nonmetal (except well and brine operations), stone, and sand and gravel operations were collected by a mandatory reporting system under the provisions of the act of September 26, 1961, Public Law 87-300 (75 Stat. 649). The act authorized the Secretary of the Interior to study the various aspects of safety in metal and nonmetal mines (excluding coal mines) and report the findings 2 years sub-sequent to the enactment of the law. Data on nonmetal well and brine plants and nonferrous reduction plants and refineries were reported voluntarily by the operators. METAL MINES Preliminary data for the metal mining industry comprise reports on 1,871 mines and pits. The combined fatal and nonfatal injury-frequency rate was 31.95 per million manhours in 1962, a decrease of 8 percent from the similar rate of 34.54 in 1961. Metal operations reported a total of 61 fatal and 3,201 nonfatal injuries.

Jan 1, 1963

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Joy Mfg. Co. shuttle car. These instructions are based upon actual installations made in the mine on two shuttle cars, model 21SC-2E. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other shuttle cars with similar protective canopies. Skilled mechanics can determine if the instructions hexein would he applicable to the other shuttle cars and can determine any necessary modifications if they are not.

Jan 1, 1973

Reduce the danger to personnel and destruction of equipment caused by fires on surface coal augers. Approach: A reasonably priced reliable system which automatically senses a fire and activates dry chemical extinguishers, has been built and field tested. How It Works: Heat sensors mounted in the engine compartment and hydraulic hose areas detect the fire, usually before the operator does. This causes the system to automatically discharge A-B-C class dry chemical extinguisher through a fixed piping system.

Jan 1, 1976

By W. R. Herrera

A research effort was conducted to present or develop methodology for evaluating candidate potting materials intended for use in explosion-proof enclosures. The primary purpose was to develop acceptance guidelines based on arc decomposition products. Acceptance criteria can be based on: ? Inherent thermo-chemophysical, mechanical and electrical properties; ? Arc decomposition products: ? Nature of volatile products produced, e.g., flammability, explosivity, synergistic effects on existing environment in the enclosure, toxicity; ? Quantity produced as a function of arc power and duration; ? Acceleration aging tests to evaluate breakdown under electrical stress.

Jan 1, 1982

By Robert J. Tuchman

This report presents the origins of the Bureau of Mines and the evolution of the Pittsburgh Research Center from its inception to its present form. Areas of major research emphasis over the years, as well as administrative reorganizations, are discussed.

Jan 1, 1998

By D. J. Parker

In attempting to discuss a subject of this character it should be clearly understood at the outset that the purpose is not to emphasize the mere fact of occurrence of such catastrophes, the memory of which time has largely relegated to oblivion, but rather to stress the means of their prevention, available not only subsequent to but also at the time of occurrence. A careful, conscientious, unbiased study of the causes of mine explosions leads inevitably and definitely to the conclusion that the human element is the most important factor. The human factor should however, be evaluated in terms of responsibility--responsibility on the part of the employer to recognize the existing hazards and take the necessary remedial action, and on the part of the employee to perform his duties faithfully, diligently, scrupulously, and in strict conformity with State mining laws and company rules or other regulations.

Jan 1, 1933

By Craig C. Johnson

The purpose of this effort was to investigate the feasibility of employing a piezoelectric transducer for seismic communications applications in mine environments. The transducer, a government furnished device incorporated a high Q, spring-mass resonator to load the air side of the piezoelectric crystal. The resonant frequency was seismic load dependent and fell in the range of 300 to 340 Hz. The effort included a mathematical analysis of the transducer, with corroborative laboratory tests, together with actual communications experiments performed first in an open-formation limestone quarry and finally in an operating iron mine. This work showed that the transducer could be coupled efficiently to hard, competent rock media with power conversion efficiencies of 70 to 80 percent (electrical to mechanical) in typical installations. In the iron mine, when radiating peak power was about 30 W (acoustical) in a gated pulse mode, signals were received at a distance of 760 ft through a massive rhyolite porphyry formation. This represents a 15% radiation efficiency with an input of 200 watts. Despite the high ambient noise level due to operating mine machinery, a signal-to-noise ratio of about 20 dB was achieved using a very narrow band filter to process the received signal, and a data rate of about two pulses/sec was demonstrated.

Jan 1, 1972