Search Documents

By Dr. Paul Worsey, Dr. Calvin Konya, Dr. Anthony Konya

Development of methods to calculate presplit blasthole pressures through simplified models, namely the Empirical Model and the Detonation Pressure Model. These models can be used with variations in explosive type and diameter, along with borehole diameter. All models have been validated with test data and shown to have minimal error.

Feb 1, 2020

By Ashwani Jain, D K. Soni

Compressive strength of rocks is often required by mining engineers and quarrying authorities for blasting operations. Uniaxial compressive strength of rocks can be predicted with reasonable accuracy with the help of point load strength tests which can be easily conducted at site by the field staff, simultaneously as the cores are recovered from drilling operations. A number of diametral point load tests and uniaxial compressive strength tests have been conducted on the specimens of different rock types under air dried, and saturated condition as well to study the effect of ground water saturation on strength. It has been observed that due to saturation uniaxial compressive strength and point load strength get reduced to a maximum of 32 and 29 per cent respectively. It has also been observed that uniaxial strength is sixteen times the point load strength in air dried as well as saturated condition. However, this factor used for calculating uniaxial compressive strength may be reduced to a lower value for the safety of miners in field blasting operations.

Jan 1, 1994

By Jean-Francois Lagueux, Andre Pomerleau

Goldex Mine is an underground mine located near the town of Val-d’Or. Multiple innovations were required to work the mine. Due to its low grade, it was important to develop a bulk mining method to economically extract the ore. The method used is a combination between shrinkage stope and long holes stope methods. This modified method is more than adequate; however, all of the ore body must be liberated in a very short period of time. Therefore, to bring down 23.0 M tonne (25.3 M ton) of ore, large blasts up to 1.8 M tonne (2.0 M ton) are required. The situation is also complicated by the fact that the mine is located in a residential area. No less that 40 homes are built within a 1 km (0.62 mile) radius of the mine site.

Jan 1, 2011

By P. Couceiro, J. Navarro

A new methodology to perform selective blast designs by adapting the explosive energy, hole by hole (or in the hole), to the rock properties as a combination of their strength properties through the X-Rock model has been developed based on drill-monitoring data from both autonomous and manual rotary drilling modes. For that, a thorough normalization process has been developed to minimize external influences in the data induced by the different rig system and the operator interventions during manual drilling operation. Principal component analysis has been used to combine drill monitoring information. Data from 48,385 blastholes, comprised in 102 production blasts at 7 different levels in one expansion of the mine have been used for the analysis. The methodology, called X-Energy, combines the X-Rock model outputs with actual blast design parameters (drill pattern, stemming and borehole length, explosive mass/density and others) and a constant variable obtained from a machine learning algorithm, to estimate size distribution and percentage of fines and coarse material, hole by hole, by combining and recalibrating the Kuznetsov (Cunningham, 1987) based equation. From it, a new shovel-independent diggability model has been developed as combination of the P80 size, the rock properties (from the X-Rock) and a constant variable obtained from a machine learning algorithm. The X-Energy application presented in this study have been implemented in Minera Escondida Limitada (MEL), to design and operate production blasts with the goal of varying the explosive density to the rock properties to obtain a more uniform size distribution and digging rates, hole by hole, based on a target size and rate, and improving slope care, preventing active faults to fail. The methodology has been applied and validated in 17 production blast (8,277 blasthole), unlocking an average of 12.8% reduction in explosives costs (explosive consumption), by combining a pattern expansion strategy and a better distribution of the explosive density within the blast. The results demonstrate how a better distribution of the explosive energy by varying its density in the hole according to the rock and blast geometry variables can reduce powder factor (explosive consumption) while improving or maintaining blasting and digging results.

Jan 1, 2024

By Gregory Hempen, Thomas Keevin, Russell Wilcox, William Wild

The Department of Defense Strategic Environmental Research & Development Program (SERDP) awarded funding for evaluation of procedures to mitigate peak pressures and energy flux density in the water column from ordnance being detonated on the ocean floor. The research purpose was to conduct scaled testing to resolve whether a theoretically-viable covering technology was operationally effective in reducing blast effects and the impacts of shrapnel. An additional objective was testing effectiveness of this method for hard-bottom units (rock or coral) and (unconsolidated) sediment substrate.

Jan 1, 2011

By Santiago Gómez, Pablo Segarra, José A. Sanchidrián

In-hole detonation pressure measurements are unusual in the production environment of a mining operation, partly owing to the hostile conditions to which recording equipment and pertinent probes must be subjected and, partly by the constraints of the production cycle. In recent decades, detonation pressure measurement techniques have been developed using low carbon resistors (LCR)-based gauges. They are cheap, relatively easy-to-operate, robust and with a high percentage of success in both open-pit and underground mining. Detonation pressure measurements are extremely important when carrying out numerical modelling to simulate explosive induced vibrations, since simulation results are highly dependent on the pressure-time history applied on the blasthole wall. Analytical equations have typically been used to model the pressure-time history; however, they usually do not adequately represent the behaviour of the explosive in terms of: peak pressure reached, rise time, mean frequency, decay and shape of the signal. Experimental records may be directly used instead of utilizing synthetic signals if they are available. In this work, (LCR)-based gauges are used to measure detonation pressure inside a production blasthole. The operation principle of the gauges utilized and the instrumentation layout is described in detail. A flexible resolution USB oscilloscope with high sampling rate has been used to catch the elusive pressure peak event. Measurements were carried out in production blasts fired with ANFO (0.86 g/cm3) in an underground mine––this also includes velocity of detonation (VOD) records––. A procedure based on the shock impedance matching has been developed to calculate the detonation pressure due to the characteristics of the gauges prevent its direct measurement. Detonation pressures obtained range from 1.71 to 2.97 GPa (248.01 to 430.76 ksi) which are in line with pressures calculated from the VOD records. Mean frequency and rise time analysis shows that 2 of 3 signals cannot be described using typical analytical equations.

Feb 6, 2023

By Rolf R. Schillinger

Subject of the paper are blasting vibrations as sources of environmental molestations including acceptance level,complaint level and damage level as well. Besides, the subject shows a comparison of international regulations and their problematical aspects. In consideration of blast induced immissions the subject shows that human annoyance has become an important place in blasting works. It provides a solution proposal how to minimize environmental effects of blasting works.

Jan 1, 1996

By Bill Birch, Toby White, Ian Brown

costs/benefits of electronic detonators and measure their effects on primary crusher productivity. 9 blasts (3 shock tube blasts, 6 electronic blasts). Measured electricity consumption & primary crusher throughput. Change to Electronic Detonators resulted in a 7% reduction in primary electricity costs and a 15% increase in primary crusher productivity.

Feb 1, 2020

By Ankit Jha, RICHARD AMOAKO

In this paper, we examine the challenges associated with the use of empirical rock fragmentation models. We highlight key parameters omitted by these models, and propose a machine learning approach that incorporates these parameters, leading to a simple, yet more accurate approach to blast design.

Feb 1, 2020

By Andrew Moore

It has long been common practice to conduct drilling and blasting operations at surface quarries in the Midwest in close proximity to near-vertical highwalls. The main reasons for such an approach, and the limited use of adequate safety controls, can be associated with higher costs, operational constraints, lithological requirements, property boundary restrictions, inadequate quarry planning, or a lack of understanding of highwall risks. Working in proximity to highwalls, without effective controls, exposes personnel and equipment to increased risk of incidents. In recent history, there have been isolated incidents involving equipment damage, or personnel injury/fatality around the United States. However, the Midwest market has largely escaped the effects of such incidents, even though the exposure rate is high. Awareness about this matter greatly increased on January 19th, 2021, when a significant incident occurred at a quarry near Green Bay, Wisconsin. As a crew was loading a typical blast near a highwall, a ground fall occurred, and multiple rock fragments struck a laborer working on the bench below. This individual sustained significant and life-altering injuries.

Feb 6, 2023

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Umit Ozer

The environmental problems such as vibration, and air blast are often faced, and discussed on mining, quarrying, civil constructions, shaft-tunnel, pipeline, and dam operations where blasting is inevitable. It is necessary to establish national standards towards to minimize the environmental problems induced by blasting and judicial matters in our country as it is in USA, EU countries and the other developed countries. This necessity and the obligatory of accepting the European Union criteria for Turkey that has started the procedure of joining to EU emphasize the importance of this study. In other words, the establishment of a particular national standard related with this subject is inevitable for Turkey. This will be possible only by studying, applying scientific methods and techniques by the experts.

Jan 1, 2010

By G. Walsh, M. T. Wild

In this paper the performance effects of linear shaped charges will be discussed. Different sized charges were tested and reviewed based on their performance used with a typical detonation method vs. detonation with a line wave generator. The goal of the project was to determine if the linear shaped charge had better performance with an ideally linear wave moving through it, verses a swept wave that is currently used. A line wave generator is a flexible sheet explosive formed into a triangular shape with holes placed in strategic places to cause a detonation wave to become linear across the width of the triangle. A standard linear shape charge with a detonator in the side of the charge was be detonated against a witness plate to get a standard depth of penetration. A second standard linear shape charge with a detonator connected to the top of a line wave generator, the line wave generator placed on top of the linear shape charge, was be detonated against a witness plate to get a comparison depth of penetration. All charges had a standoff 1.5 times the width of the cavity, allowing the data to be compared to the control charge. Computer modeling was intended to be used to predict the results from testing these designs in the field. The actual results were compared among themselves.

Jan 1, 2011

Currently there exist several explosive quantity-distance (Q-D) rules variously exercised by most countries to protect personnel and property against the effects of accidental explosions. These regulations apply to manufacture, transport and storage of explosive products. This paper reviews the technical basis behind these regulations, as they apply to commercial and military explosives. The characteristics of a blast wave and missiles issuing out of an explosion site and their role in determining the level of damage to a target are discussed. The need for further research on the effect of detonation of charges of non-standard geometry, and under confined conditions such as tunnels is discussed. The challenge in estimating the net quantity of explosives involved and calculation of its TNT-equivalency is also highlighted.

Jan 1, 2011

By Travis A. Davidson, Ralph E. Burnham, Cathy Aimone-Martin, J. Kelly Ratliff

Blasters face a long list of tasks to execute daily—from vehicle inspections to blast design and layout, hole loading and tie-in, securing the site, and finally, safely executing the blast. Good practices and, in most cases, regulations and requirements necessitate documenting their work, specifically their blast report. While some blasters use paper forms, others use electronic means to streamline the process. The authors have served as attorneys and expert witnesses in representing companies and individual blasters in numerous administrative and legal matters in which documentation of the blaster’s work was both critical and detrimental to the effectiveness of defending their work. This paper discusses in a case-study manner the authors' observations concerning good blast report format, specific observations around electronic and paper report completion, record-keeping, seismograph setup and recordkeeping, video and photo documentation, internal auditing, and other topics related to documenting the blast. The paper aims to serve as a discussion guide for blasters to improve their blast record-keeping process, develop better practices that effectively document their work, and allow them to defend their work should a claim arise concerning their operations.

Jan 21, 2025

By R W. Thomas

This paper explores the possibilities of generating radical improvements in the drilling costs and productivity of blastholes through the efforts of integrated teams as opposed to traditional customer/vendor relationships.

Jan 1, 1996

By Dennis Wilzbacher, John Wiegand

In an effort to reduce the cost of bulk explosives, Vigo Coal Company found that the addition of coal mined at their Friendsville Mine, not only reduced explosive costs, but also appeared to actually enhance blasting performance. The Friendsville Coal lies at the base of the Mattoon geologic formation within the Mcleansboro Group of the Missourian Series of the Pennsylvanian Geologic System in Southern Illinois. Vigo Coal Company commissioned VIBRONICS, INC., an independent blasting consulting company to quantify actual blasting performance. Insitu sonic velocity testing of overburden was conducted to determine the P-wave velocity of the sandstone present at Vigo’s Cypress Creek Mine, where the initial testing was conducted. Numerous VOD (velocity of detonation) recordings were obtained for varying blends of ANFO/Coal (now named Carbo*Prill). Cast blast percentages were determined for both Carbo*Prill and non coal blended bulk explosive blasts. The VOD of the coal blended product was intentionally reduced so as to more closely match the P-wave velocity of the sandstone overburden. Explosive blends containing as much as 40-50 percent coal were tested. Explosive blends containing greater than 30 percent coal, have been used in Cypress Creek Mine overburden production blasts. The coal blends appear to produce better fragmentation and yield excellent cast blast performance. Safer mining conditions were also observed. Flyrock potential was reduced. The blasts produced less back break, producing a safer highwall. Stripping dozer and shovel production rose during the testing period and equipment repair costs were lowered due to an increase in overburden fragmentation. Blasting vibrations were reduced, in part due to the lowered detonation velocity of the ANFO/Coal mixture. The Friendsville Coal Seam appears to contain inherent chemical and physical properties that enhance blasting performance. The use of Carbo*Prill has been approved by MSHA, BATF, the State of Illinois, and the State of Indiana. This paper will provide details concerning testing procedures, blast performance analysis, recommendations and conclusions for using this alternative blasting mixture.

Jan 1, 2007

By Miguel Humpire Huamani, Gustavo Huerta Valer, Jorge C. Cárdenas Miranda

As part of the continuous improvement and increase productivity to achieve the mining and extraction plan of a low-grade open pit copper operation, alternatives are required to expand the blast pattern to maximize drills and steels resources along to ensure the fragmentation results for the process plant with volumes from 500k tons of broken material per day. Therefore, the application of aluminum based ultra-high energy explosives was an alternative to achieve the objective of expanding the production pattern by 34% while maintaining energy factors levels along with the distribution of explosive and the application of the pocket charge in the stemming level, reducing the load factor, maintaining the fragmentation results in P80 and increasing the percentage of fines less than 1.0 in (2.54 cm). An important development to ensure the supply and perform successfully blasthole loading was the implementation of a supply system with pre-blending (aluminized emulsion) which is stored in silos and load through factory trucks. In the field we ensured optimal initial and final density levels with chemical sensitizer to perform the most fracturing work in the rock, complementary evaluations were performed to predict flyrock and define safe equipment evacuation radiuses along with advanced vibration monitoring for the sustainability of the mine.

Feb 6, 2023

By Joseph Indeck, Seokbin Lim, Andrew Thompson

In the design of explosively driven penetration devices, understanding the impact conditions between the explosively propelled penetrator and the target is one of the most important steps in optimizing the performance of the device. These impact conditions are especially prevalent when a shaped charge jet impacts concrete, which is not an ideal target material. The specific impact conditions, including but not limited to the impact angle and jet properties, create a great deal of variability that affects the performance and penetration of the shaped charge. The large amount of impurities and voids in concrete, along with its heterogeneous nature and the general strength characteristics, make concrete a non-ideal material for shaped charge jet penetration. These material characteristics lead to a highly non-linear deformation behavior of the concrete target during a hyper-velocity impact.

Jan 1, 2011

By Lynn Long

We have seen many new developments in the explosive and blasting accessory category, but one of the most useful items is the blast control plug. Blast control plugs are cone shaped units that are placed in the stemming just above the explosive load. They are placed about 8 to 12 inches up into the stemming material.

Jan 1, 1996

By Hairong Zeng, Matthew Baumann, Shahram Tafazoli, Edmond Chow

Measurement of rock fragmentation has evolved from a completely subjective and manual process to a statistically objective and semi-automated process. However, ultimately, the vision is to achieve a statistically representative and fully-automated process. From the blast optimization perspective, it is critical to receive reliable rock fragmentation results quickly to incorporate into the planning of subsequent blasts. Since manual rock fragmentation measurement methods tend to be time consuming, a fully-automated method is the practical way to meet these requirements.

Jan 1, 2012