Search Documents

By R L. Calhoun

A paper on High Pressure Air must start with the industry accepted definition of High Pressure Air and, for the reader who is unfamiliar with High Pressure Air systems, include basic information on which type of Drilling Rigs can benefit from the use of High Pressure Air. The operation of a modern Downhole Drill must also be reviewed.

Jan 1, 1976

By Tassilo Baur

Explosives are used in the entertainment industry in a wide variety of applications. Live performances such as automobile races, air shows and the like have incorporated the use of explosives into their programs. Even art work has been created employing explosive materials and techniques. The primary entertainment use of explosives, however, remains in motion pictures, television, theater and related fields where it comes under the auspices of special effects. Much of it falls roughly into the category of demolition, though the object being demolished may range from a cigarette in a person's mouth or clothing worn by actors to large objects such as automobiles, aircraft, or boats. This paper will attempt to provide an overview of the materials and methods by which these special effects are created as well as highlight the unique problems encountered in this field and their often equally unique solutions.

Jan 1, 1992

By Mark D. Kirkbride

This paper outlines the process for designing a hard rock blast in an underground coal mine. The coal mine is located in Western Kentucky and operates four continuous miner units at 7 unit-shifts per day. The mine operates in the Western Kentucky No. 11 Seam with local variations from 4.5 - 5.5 feet seam thickness. The seam has sporadic siderite deposits. Usually these deposits do not significantly interfere with the mining process. When previous siderite deposits were encountered they were small enough to drop an entry for a couple of crosscuts. The blasting plan was called for after a siderite deposit was encountered in the belt entry at about one third of the panel length. The other sides of the panel had been previously mined and sealed so the decision was made to mine through the siderite deposit with the continuous miner instead of abandoning the panel. The deposit was approximately 300 feet in length down the belt entry. Mining through the deposit with the continuous miner was expensive in both terms of production and of wear and tear on the continuous miner. A blasting plan for the siderite deposits was designed to minimize damage to the continuous miner should a similar situation occur.

Jan 1, 1999

By Richard W. Watson, Julius Roth

The Bureau of Mines has recently completed a contract study of the hazards associated with surface mining.! Part of this effort involved an analysis of surface mining accidents associated with blasting activities. For this purpose, 71 reports of accidents investigated by the Bureau of Mines or the Mining Enforcement and Safety Administration (MESA), covering the period from 1962 to 1976, were collected and analyzed. In addition, blasting accident frequencies for the period 1973-1976 were extracted from the central computer files maintained by the Health and Safety Analysis Center (HSAC) in Denver, Colorado. This paper presents a preview of the findings, which are treated in more detail in the final report.

Jan 1, 1978

By Martin L. Smith, Robert L. Hautala

The objective of blast optimization can be approached either in a qualitative sense of designing a blast which will be "trouble free", or quantitatively in the sense of minimizing overall mining costs. Blast design simulators and fragmentation models have become an accepted tool in blasting over the last decade. Numeric simulators are very useful for solving quantitative problems, but are limited in their ability to address more qualitative problems such as post-blast bench condition. Also, current blasting models are limited by the complexity of site-specific blasting and are not functionally suited to mathematical optimization. As a result a great deal of expertise is still needed in optimizing a blast. The following describes the application of an expert system approach to integrating both a symbolic model of the expertise of the blasting engineer for attaining a trouble free blast, and a numeric optimization model relating fragmentation to unit operations from drilling to grinding. Research into this application of a coupled modeling approach to blast design is being carried out to develop a modeling methodology which will provide a suboptimal design for qualitative design goals as well as minimizing blast related costs.

Jan 1, 1991

By Dale Nies, David P. Childs

The open pit gold and silver mining operations in the State of Nevada have historically used simple row by row, echelon, or chevron delay patterns. Common practice has been to use detonating cord trunklines and either detonating cord downlines or nonelectric common in-hole delays in conjunction with surface delays. Several operations use a series of downhole nonelectric delays with an entire row loaded with the same delay to develop similar patterns.

Jan 1, 1991

By Marlyn G. King, Robert L. Martin

Blasting activities in all four pits at Thunder Basin Coal's Black Thunder Mine are focused on cast blasting. With widths varying from 190 feet to 265 feet and bench heights varying from 90 feet to 175 feet, casting efficiencies vary with different geometry's. For example, the percent cast to final in the 200 foot pit is on the average higher than the 270 foot pit. The powder factors are somewhat higher in the narrower pits, thus increasing the cost of blasting. This leads to a very detailed look at the actual benefit of cast blasting and the associated cost of these benefits.

Jan 1, 1995

By Rolly Thorpe

Bulk emulsion explosives have been used at surface mines and quarries for many years. Recently, this technology has been adapted for underground use in relatively confined work areas and in smaller diameter blastholes.

Jan 1, 1994

By John W. Kopp, David E. Siskind

Over 4 billion pounds of commercial explosives are used by the U.S. mining industry every year with an excellent and improving safety record. However, accidents involving explosives are seldom minor. They produce a disproportionate amount of fatalities compared to other mining activities, as reflected in the relatively high severity rates. The U.S. Bureau of Mines (USBM) has been analyzing blasting accident data obtained from the Mine Safety and Health Administration (MSHA) to determine the most frequent causes of mine blasting accidents, examining trends in these accidents, and identifying areas of needed research. This paper is an update of three previous blasting accident studies conducted on 4-year intervals by the USBM and published in 1983, 1987, and 1991, and is based on a total of 869 blasting accidents.

Jan 1, 1995

By Carlos Agreda

"In the present article a case study of ammonium nitrate in mine water is briefly analized and discussed. Causes of mine water pollution from AN are very well identified and emphasized.Some preventative measures, as well as, some methods of monitoring and control to minimize, mitigate and/or avoid mine water pollution are recommended."

Jan 1, 1999

By Paul Miller, Rene Laprade

Does a 76 mm Ø hole drilled over 45 m deep remain straight? This is the question asked by the Engineering department at Placer Dome's Dome Mine in Timmins, Ontario before they could lay out the initiation sequence in a long-hole production stope. Everyone realized that the holes would wander over such great depths, but it was important to know where they went.

Jan 1, 1998

By Scott Giltner, Allan Koski

Blasting is one of the lowest cost yet most critical parts of the mining cycle. This paper discusses the findings of an audit conducted on the blasting operation at an iron ore mine. The purpose of the audit was to review current blasting practices in order to identify opportunities for production/cost improvements. The approach taken in the audit was to observe general blasting practices, their related downstream effects and to compare current procedures to established best practices.

Jan 1, 2009

By J Brent Gilion, Gary Eck, O Machacek

The research presented herein is the result of internal efforts as well as efforts under subcontract to United Technologies Chemical Systems Division San Jose, California . The efforts were focused on investigating the feasibility of using excess energetic materials from the Department of Defense and Aerospace Industries as ingredients in commercial explosives. The management of the excess energetic materials inventory in this country has become a serious problem facing the Department of Defense and its contractors, the Aerospace Industry and both state and federal regulatory agencies.

Jan 1, 1994

By Steve Dillingham

With the millennium fever all but faded, we look to a new century filled with awe and excitement. We step forward in time, marveling over the achievements of the 20th century and wondering what the next 100 years could possibly bring. Will there ever be another time that produces such technological advances, economic progress or social changes? Keeping pace with the awesome accomplishments of the past century has not been an easy task and we must prepare ourselves for the possibilities of the future. Take, blasting safety for instance. We all know that safety is personal - a culture - promulgated not only by the company by which you are employed, but, by a sense of your own personal responsibility that must constantly be reinforced through awareness, training, and discipline. Great strides have been made in blasting safety since its crude beginnings, however, safety consciousness becomes even more important as technological advances and scientific progress are made in the coming years. It all begins with a positive safety attitude where every employee habitually examines each situation encountered, identifies potential hazards, and takes precautions to avoid those hazards.

Jan 1, 2002

By D G. Dressler, Paul Yeager

A previously little-known facet of seismic frequency spectrum analysis is gaining significance. The frequency spectrum of seismic waves promulgated from blasting is a significant factor in causing blasting complaints and threshold (architectural type) damages.

Jan 1, 1987

By Lewis L. Oriard

The purpose of this paper is to provide an overview of close-in blasting effects on various types of structures and building materials, as encountered in this writer's professional practice. Structures range from old, deteriorated historical monuments to new, heavily reinforced buildings. Materials range from clay adobe to concrete and steel. Site locations range from tropical to arctic. Blasting ranges from sculpture blasting inside buildings to "coyote" blasting and large surface blasting operations. Space limitations permit a brief discussion of only 25-30 specific cases, but they have been selected to be typical of conditions found on hundreds of similar cases. The writer was asked to present a discussion of representative cases where relatively high vibration intensities were experienced. Virtually all of these cases were free of damage, but the few damage cases provide valuable insight to the mechanisms involved. Observations of such damage and non-damage cases have served as the basis of this writer's criteria for various structures and materials, as well as the technology to conduct blasting operations within those criteria. A sampling of these experiences is gladly shared with the reader.

Jan 1, 1991

By R J. Roach, D Roy

After months of discussion on ways and means to improve productivity in the shaft sinking process, it was decided to look at those areas where, historically, methods have been stagnant for many years. These categories included drilling, hole diameter, drill patterns, explosive types, explosive loads, initiation techniques, cut design, wall control, fragmentation and heated magazines.

Jan 1, 1997

By T Guiliani, F Ottuonye

Explosives casting is gaining increasing popularity as an overburden removal method in strip mining because the coats of using explosives to cast a percentage of the overburden to the spoil are lower than the costs of using stripping shovels or draglines to do all the overburden removal. This is due to the rising capital and operating costs of draglines and shovels.

Jan 1, 1989

By T J. Wilton, K A. Broadhurst

The United Kingdom, although a relatively small island, has a wealth of mineral deposits, coal, granite, limestone, gypsum, lead, florspar, etc. Coal is a major source of energy with 71 opencast coal sites, 52 using explosives. Many of these sites are in rural areas, the average area worked being 250 acres. The smallest is 35 acres, the largest 2,000 acres, but only 600 acres can be operated at any one time.

Jan 1, 1981

By S B. Richardson, R E. Danell, D Mead, N T. Moxon

Explosives provide a very concentrated source of energy which is often well in excess of that required to adequately fragment the surrounding material. Blast design, environmental requirements, production requirements and the lack of detailed insitu geological data generally limits the degree to which the explosive energy distribution within the blasthole can be significantly altered using, for example, different explosive formulations or variable loading techniques. However, increased flexibility can often be exercised over a blast through the use of air-decks.

Jan 1, 1993