Search Documents

By Yang Zhao, Tao Xiu-xiang, Chen Song-jiang

"China is rich in low-rank coals that account for 45.68% of existing coal reserves in China. The clean and efficient utilization of low rank coals is of great significance for ensuring the effective energy supply and promoting economic development and environmental protection. In order to solve the difficult problem in flotation of low rank coal, it has become the focus of research in the related field that oily bubbles instead of air bubbles are taken as a carrier in flotation to improve the attachment efficiency and recovery of low rank coal. In this paper, low rank coal slime collected from Shendong mining area was used as the experimental material, and it focused on the characteristics of oily-bubble flotation process of low rank coal. Additionally, difference in conventional flotation and oily-bubble flotation was discussed. The induction time between air bubbles, oily-bubbles and fine low rank coal particles was measured. The results indicated that the induction time between oily-bubbles and coal particles was obviously lower than that of air bubbles. By comparing the foam height of air and oily bubbles, it was found that the amount of oily bubbles is less than air bubbles, causing relative low flotation rate of oily-bubble flotation at initial stage. Besides, the maximum foam height and half-life of air bubbles and oily-bubbles were measured respectively. The results showed that the stability of oily-bubbles was higher than that of air bubbles, which is benefit for the enrichment of concentrates. The clean coal water recovery of oily-bubble flotation is lower than that of air bubble flotation, which indicated oily-bubble flotation is lower in water entrainment. INTRODUCTION China is the largest energy consumer in the world, accounting for 23% of global energy consumption in 2016 and 27% of global energy consumption growth. Whereas coal is taken as the major primary energy source and its share of China’s primary energy consumption is 62% in 2016, in which the low rank coals, such as lignite, long-flame coal, weakly caking coal, and non-caking coal, accounted for about 50% of total coal production capacity (China’s energy market in 2016, BP). Moreover, the exploitation and utilization of low rank coals and other coals that are difficult to float have been an important strategy for China’s sustainable development of the coal industry (Liu et al., 2014). However, the combustion of low-quality coals leads to a serious environmental pollution. In addition, the deterioration in geological conditions of coal resources, and the increasing improvement in the mechanization for mining significantly caused the increased amount of fine coal."

Jan 1, 2018

By Nani Pajunen, Kari Heiskanen

"Products filling our societal needs, like communication and transportation needs, are becoming more sophisticated and efficient. The cost has been an increased complexity of material combinations. The same trend is also seen in investment goods. As an example, different crusher types have almost doubled the power to weight ratio in a relatively short time while producing even higher crushing rations. This has been possible by high performance materials and advanced designs. Another example is new hybrid materials in prefabricated high-strength steel structures in construction with the aim to lighten the products and obtain energy savings in the use phase e.g. in transportation. This development in general has made the end of life phase obscure. Recycling is often understood as the first phase of the material cycle. This has been supported by the material centric point of view. When, say indium, has been collected and mechanically treated to a concentrated fraction, it is assumed as recycled. This is not the case. The same applies to special steel alloys where one tends to lose some of the alloying elements to slag or even into the gas phase in the melting and refining stage, not in the earlier steps of recycling. At present there is no clear understanding of recycling of hybrid materials and no clear willingness to create new functional recycling systems. As the EU directives and most of legislation worldwide are based on the material centric thinking and implemented even on total mass recovery basis there is neither legislative incentive nor very strong economic incentives to work out the problem. In our research, we focus on industrial design towards sustainability from a product centric point of view from product collection to final metallurgical steps. It is vital, in the design phase of product, to understand the effects of decisions on recyclability to a saleable raw material. Main goal of our work is to create the fortunate circumstances in supply chain - to pass the barriers and find the effective and fruitful drivers - for reasonable use of raw materials and recycling co-operation with industry. The boundary conditions in the work are extractive metallurgical performance and the economic viability of all the steps. It can be shown from our work that small design alterations may have a large impact on the recyclability. The earlier the decisions are made in the product life chain the more positive impact they will have. It can also be shown, that a strong processing and metallurgical industry is vital to any meaningful recycling of the modern EoL products. Finally, it is also question of the individuals and values: supply and demand. Are you ready to take up the gauntlet: demand recyclable products."

Jan 1, 2014

By Marco Le Roux, Martha Van Rensburg, Quentin Campbell

Fluidised bed drying is currently receiving much attention as a dewatering option during the beneficiation of fine (defined here as between 1 mm and 2 mm particles) coal. Apart from concerns about safety and combustion, the operating costs can be high if very high gas or air temperatures are used. The aim of this study was to investigate the removal of moisture from fine coal by using air at a lower temperature (25 - 55°C) within a controlled environment by lowering of the relative humidity of the air. It was firstly proven that fluidization has a major advantage over non-fluidized beds, with regards to drying rate and final moisture content. Hereafter several parameters that influence the dewatering rate and final moisture content were tested, from which it was concluded that the relative humidity of air acts as the largest driving force for dewatering. Parameters tested included relative humidity, temperature and coal composition. Energy balances showed a positive nett energy increase in the dried coal during combustion when related to the energy input during drying. In comparison with thermal drying technologies, fluidized bed drying was proven to be less energy intensive. It was therefore shown that this is a viable technology for the dewatering of fine coal.

Jan 1, 2014

By Francesco Vegliò, Luigi Toro, Francesca Beolchini, Francesca Pagnanelli, Stefano Ubaldini

"Biosorption is an innovative technology used to remove heavy metals from aqueous solutions from mining waters and other industrial wastes. A wider application of this alternative process is strictly dependent on the understanding of the chemico-physical aspects involved, in order to optimize the operating conditions. Mechanistic models are the most useful tools used for understanding purposes, even if the empirical models are still widely applied for their simplicity.In this paper especially propagated biomasses of Sphaerotilus natans, calcium alginate and some waste materials were tested as adsorbents for single and binary solutions containing heavy metals at different pH. The equilibrium experimental results were fitted according to empirical and physical models with growing complexity outlining the inadequacy of the predictive models; in fact, the non-ideal interactions among metals require the insertion of additional correction parameters."

Jan 1, 2003

By X. M. Wang

Magnetic floatation column (MFC) is a new equipment used for increasing content of iron, in which magnetite is separated in open gradient magnetic field. Simulation study was performed to investigate the separation characteristics of the separation method by analyzing the dynamic motion of magnetic particles. In this paper we compare two magnetic fields created by different magnets. The obtained simulation results give perspective in industrial design of MFC as the basis stage.

Jan 1, 2014

By Wolfgang Öfner

Many technical processes also yield dusty residues which usually contain appreciable amounts of valuable matter. Often they also accumulate substances detrimental to the process. Dumping them entirely in landfills wastes raw material and causes high disposal costs, but recycling them without prior treatment is often not feasible. Physical separation processes are preferable because of their rather low energy demand. In order to develop such treatment systematically, the residues must be characterized properly. The technique for such a characterization is taken from mineral processing: perfect fractionation according to continuous properties of the particles supplemented with chemical analysis are used for plotting the Henry-Reinhardt chart. This represents the benchmark for assessing actual separation processes and tests. Their results are compared in terms of ?selectivity? and plotted in the kappa chart. In this paper, Henry-Reinhardt chart and kappa chart are applied to several different types of residues from iron and steel production and show their potential for being upgraded before reutilization in the production process. This approach is suitable for virtually all dusty residues from other industrial processes as well. Keywords: residue, dust,iron and steel, process development, Henry-Reinhardt chart, kappa chart

Sep 1, 2012

Dielectrophoresis is a separation technique that uses a non-uniform electrical field to separate particles on the basis of their permittivity. There are many areas of mineral processing that might benefit from the application of dielectrophoresis. These include: coarse removal of gangue, recovery of ultrafine particles, upgrading of flotation concentrates or simply as a laboratory analysis technique. In order to determine the potential value of dielectrophoresis to the mineral processing industry, the response of composite particles was investigated. The electrical properties of composites involve complex relationships between the shape, distribution and permittivity of the individual grains within the rock. The relationship between mineral composition and dielectrophoretic force was measured on single particles from two ore types. The results were used to populate a model that could predict the separation characteristics of the ore. The insights gained from this model separator allowed potential applications of the technology to be examined and their performance evaluated.

Sep 1, 2012

By V. M. Bystritsky, M. G. Sapozhnikov, G. M. Nikitin, A. B. Sadovsky, Yu. N. Rogov

"At present kimberlite ore is processed in crushers or grinding rolls with subsequent grinding in wet mills down to a size of 0.2 mm. The basic disadvantage of the standard diamond processing technology is that crushing kimberlite ore can damage the most valuable large diamonds of few carats. Tagged neutron method offers a possible solution to this problem. It allows detecting diamond inside kimberlite ore without its disruption. The results of the tests of the neutron separator prototype carried out at the Lomonosov processing factory of PJSC Severalmaz are discussed. The possibility to detect the diamond in the rock whose size is 10 times larger than the size of the diamond is demonstrated.INTRODUCTION At present standard diamond processing technology implies disintegration of kimberlite ore in crushers or grinding rolls down to a size of 0.2 mm. It inevitably leads to high probability that large and most valuable diamonds could be damaged. The fraction of diamonds which lost integrity in the process of ore enrichment could be as large as 35-65% [1]. Tagged neutron method (TNM) [2] offers a possible solution to this problem. It allows detecting diamond inside kimberlite ore without its disruption. The main idea of the TNM is irradiation of an object by fast 14.1 MeV neutrons from binary nuclear reaction d + 3H ?4He + n (1) and detecting (tagging) the 4He (a-particle) that accompanies neutron. That gives possibility to determine direction of the neutron momentum. Those tagged neutrons irradiate kimberlite ore under investigation and produce gamma rays via inelastic scattering reactions with nuclei"

Jan 1, 2018

By C. P. Lowes

"The REFLUX™ Classifier (RC™) consists of a fluidized bed housing, with a system of parallel inclined channels above. This system performs a simultaneous gravity separation and desliming of the feed material, utilising the inclined channels in order to retain the relatively fine dense particles. These particles promote the formation of an autogenous dense medium within the fluidized bed. Relatively large, low density particles are displaced from the fluidized bed and conveyed upwards through the inclined channels reporting to the overflow with other finer particles. Given the hydrodynamic role of both the particle size and density in determining the particle transport through a water based suspension, all gravity separators operate over a limited size range. In the case of the REFLUX™ Classifier, efficient separations can be produced across a very broad size range, from nearly 10 mm down to 10 m, however, for a given application the size range is much more limited. This study was concerned with the processing of dense minerals over a broad size range, and the need for multistage processing. Here the overflow from the first stage cascades to the second stage, incorporating coarse gangue rejection. This approach is shown to deliver remarkably high grades and recovery.INTRODUCTION The performance of the REFLUXTM Classifier (RC™) in beneficiating fine coal is well documented (Galvin, 2012). Although the technology can be applied to relatively fine particles below 0.1 mm, or coarser particles below 2.0 mm or even 8.0 mm (Galvin et al., 2010), in each case the technology is applicable to limited particle size ranges. In coal preparation, the most common size range is 0.25 to 2.0 mm, covering an eight-fold range in the particle diameter. Coal has a relatively low density, typically below 1600 kg/m3, with a significant portion below 1400 kg/m3. In water, the buoyant density difference (~ 400 kg/m3) is therefore low compared to that of gangue minerals (1600 kg/m3) by a factor of 4, enhancing the potential for separation. Thus, in coal preparation, the technology can be applied over a commensurately broader size range, typically up to eight-fold."

Jan 1, 2018

By Güven Önal, Zeki Dogan, Neset Acarkan

In this study, it was aimed to produce glass sand with less than 0.15% Fe2O3 for window glass manufacture and glass ware grade with less than 0.05% Fe2O3 from Yalõköy sand dunes having 0.48% Fe2O3. In order to reduce the iron content of the Yalõköy sand dune, magnetic separation, flotation, scrubbing, H2SO4 leaching and drying were used. The optimum iron removal was achieved by H2SO4 baking at 150oC and 8 kg/t acid consumption. In this way, sand concentrate was obtained with 0.04% Fe2O3 and sand recovery 95%.

Jan 1, 2003

By M. E. Ramírez

In this research bioleaching or extraction of iron present in a kaolin from La Virgen mine, Anti-oquia/Colombia, was carried out. Organic acids produced in SF with Aspergillus niger were used in the process. The fermentation process was carried out in 3 L aerobic stirred bioreactors, at a temperature of 30 °C, a stirrerd speed of 700 rpm, an initial pH of 4 and a fermentation time variable between one to 8 days, obtaining broth fermentation samples daily per bioreactor. For iron extraction, fermented broth from second to sixth day of fermentation was evaluated and it was found that the fermentation broth of the third day showed a larger potential for iron removal, 786 ppm, by using kaolin with an initial iron content of 1401 ppm. A set of tests using commercial organics acids such as citric acid and oxalic were carried out because those were found in the fermentation broth and it was found that oxalic acid presented three times more iron removal than citric acid.

Jan 1, 2014

By S. Fiore, M. C. Zanetti, C. Clerici

The processes and fluxes of a cast iron foundry plant located in the North of Italy were analyzed in order to determine the amount and kind of wastes produced from the different activities. The main fractions are the molding sands, furnace muds and powders coming from the dust abatement plant, the exhaust lime, the furnace refractory, the metallic shotting and the sludges and powders coming from the dust abatement plant of molding lines for a total production equal to 800 t/d. All wastes were sampled and particle-size and chemically characterized to evaluate the best recycling or reuse solutions. Wastes were sieved and divided in three categories according to the particle-size dimensions: below 0.1 mm, between 0.1 and 0.6 mm and above 0.6 mm. The fraction above 0.6 mm dimension underwent magnetic separation to recover and quantify the potentially available iron fraction. The fraction between 0.1 mm and 0.6 mm was chemically characterized in order to understand if it could be fed to the sand regeneration plant. The below 0.1 mm fraction was characterized to evaluate the following recycling and reuse solutions: additive for molding sands and/or raw material for the concrete industry.

Jan 1, 2003

By Kari Niiranen, Andreas Fredriksson

LKAB (Luossavaara-Kiirunavaara AB) is operating iron ore mines, concentration plants and pelletizing plants in Northern Sweden. Geometallurgy, which combines geological and metallurgical information is not a new way of thinking at LKAB, but rather a revised and updated version of an old working process. A project called "Silica in the Mine" which started in 2007, was an important reason to set a new focus at the geometallurgy. The target of the project was to develop a simplified method in laboratory scale to predict SiO2 grade in the magnetite concentrate in Kiruna and further predict the physical properties of the crude ore with respect to processing characteristics. The connection between mineralogy and products properties have started to be even more vital and necessary to examine due to the future exploiting new iron ore deposits. Geometallurgy at LKAB can be described as a mental and strategic framework where the Research and Development department (R&D), and others within the organization of LKAB, aims towards the connection of the minerals-production-products. It could in its basics be called "research & development", but it must be clarified that changes have been made, mainly due to the development on the instrumental analysis side. LKAB’s idea is to work quite broad, with internal educations, an active working process in ongoing projects, together with external parties (such as universities), with several PhD-projects and an upgrading on the instrumental side at the LKAB Research & Development department. This paper is a summary about the concept Geometallurgy at LKAB and some of the actions within its framework.

Jan 1, 2014

At times the phosphate industry, in Florida, encounters phosphate rock that gives lower than expected P2O5 recovery in the rougher plant section. The drop in recovery is typically 10% and as much as 30% or more. Variations in feed quality from day to day, shift to shift and even from drag-line to drag line, represent a challenge to the beneficiation plant operators and reagents? suppliers. Therefore, this characterization study has been initiated to identify the reasons for the differences in flotation behavior of such feeds. The study involves many samples to cover such variations. The characterization work includes: ? Mineralogical and chemical analysis; ? Size, shape, surface roughness and porosity analysis; ? Surface charge and surface contamination with other phases (minerals); ? Clay content and its relationship to phosphate and silica particles. The results correlated with flotation data and adsorption density measurements clearly establish the statistically significant variability in characteristic features that influence flotation response. This article discusses results from the above listed studies. On the basis of the obtained data, recommendations of practical approaches to overcome the problem of feed variability in phosphate flotation plants are delineated.

Jan 1, 2014

By A. Otsuki

This paper describes the evaluation method of dispersion and coagulation of silica nano-particles by means of interactive force apparatus. The apparatus measures the size of fine particles in aqueous solution or organic solvent of high concentration and/or low optical transparency. Other conventional apparatus for size measurements (such as, apparatus utilizing dynamic light scattering) are difficult to measure the size of particles in such conditions accurately, due to multi-scattering of light in the sample solution or solvent. The apparatus measures the interactive force between two surfaces, i.e. the gold-coated glass hemisphere and the brass flat plate, (which is fixed at the bottom of the sample cell). The apparatus has three parts, i.e. main part (which consists of electric balance, hemisphere and flat plate), control part (i.e. personal computer, piezo-stage controller and voltage supplier), and detecting part (i.e. multi-meter and oscilloscope). During the measurement, electric field is applied between the hemisphere and flat plate, and thus dielectric particles are arranged toward the direction of electric field in the area between two plates. When the two plates are close to each other, two different forces (i.e. repulsive force and attractive force) will alternately act on particles due to the structure change of the particles. The repulsive force occurs when the structure of particles is stretched by compressive force; whereas the attractive force occurs when the aggregate structure is broken. The cycle of the repulsive and attractive forces is a primary size of particle or size of aggregate, which depends on the degree of agglomeration. The measured size of particles, which is varied depending on their degree of dispersion and coagulation, determined the characteristics of the silica particles. In this research work, the effect of size and concentration of particles in aqueous solution on the degree of dispersion and coagulation of the silica particles were investigated. Spherical silica particles were selected for this investigation due to their variety of size. This apparatus can be used to evaluate the degree of dispersion and coagulation of other nano-particles in various solvents in many process industries.

Jan 1, 2014

By K. A. Natarajan

"Interaction with microorganisms results in significant surface chemical changes on minerals. For example, chemolithotrophs such as Thiobacillus ferrooxidans and Thiobacillus thiooxidans significantly alter the surface chemistry of several sulfide minerals such as pyrite, chalcopyrite, sphalerite and galena. Heterotrophic bacteria such as Bacillus sp. could alter the electrokinetic properties of oxide minerals such as hematite, alumina, silica, kaolinite and calcite. Microbe-mineral interactions could thus be beneficially utilised in mineral beneficiation as different from bioleaching. Microbially induced mineral beneficiation unlike bioleaching deals with interfacial phenomena at mineral-solution-bacteria interfaces and surface chemical changes are brought about at very rapid rates amounting to a few minutes resulting in mineral separations in an aqueous medium.In this paper, the role of acidophilic chemolithotrophs such as Thiobacillus thiooxidans and neutrophilic heterotrophs such as Bacillus polymyxa in the beneficiation of sulfide and oxide minerals is illustrated. Mechanisms of bacterial attachment on various sulfide and oxide minerals are outlined with respect to the influence of bacterial interaction in bringing about mineral surface hydrophobicity or hydrophilicity. The role of bacterial cells as well as metabolic products such as bioproteins and exopolysaccharides in significantly altering the surface chemistry of sulfide minerals such as sphalerite and galena and oxides such as hematite, alumina, silica and calcite is discussed with probable mechanisms. Possibilities of generating mineralspecific bioreagents are outlined with respect to bacterial adaptation to mineral substrates."

Jan 1, 2003

By Tuan V. Nguyen, Kosta Simic, Louis Mittoni, Murray Rudman, Jean D. Swift, John B. Farrow, Phillip D. Fawell

"Research projects towards developing a sound understanding of the factors controlling the performance of gravity thickeners have been conducted by the AJ Parker Cooperative Research Centre for Hydrometallurgy since 1988 through AMIRA International. The current phase of this work, the three year P266D .Improving Thickener Technology. project, has 27 sponsors comprising mineral processing companies, reagent suppliers and thickener manufacturers.These projects have resulted in the development of a range of tools and techniques to address flocculation, thickening and associated dewatering issues. A number of Computational Fluid Dynamics (CFD) models have been developed to predict likely full-scale thickener performance under various process conditions, based upon a knowledge of thickener design, plant flows and assessment of the flocculation behaviour of the feed slurry. At the same time, various laboratory and plant studies have been used to quantify important thickener processes, and to provide validation of the CFD models. These numerical and experimental capabilities have been applied to various thickener issues across a broad range of mineral processing operations, leading to significant process improvements and substantial financial benefits.This paper presents an overview of the work conducted during these projects, focussing on the research tools, the nature of the information that has been gained and the implications for thickener performance."

Jan 1, 2003

By Francesco Vegliò, Luigi Toro, Francesca Pagnanelli

Different hydro-metallurgical processes have been studied in order to recover manganese(II) from oxidised minerals such as MnO2. An innovative acid reductive leaching carried out in mild experimental conditions was here considered using agricultural and industrial wastes containing carbohydrates as reducing agents. The leaching process was investigated from a kinetic and equilibrium point of view in order to optimise the experimental conditions, develop a kinetic model and obtain high purity concentrated MnSO4 solutions. To study the leaching kinetic a Shrinking Core Model (SCM) was modified by a variable activation energy term to take into account both the variable reagent concentrations and the reaction rate change with respect to the manganese dioxide conversion. The influence of the particle size in the kinetic model is discussed with the support of SEM analysis before and after leaching. Manganese extraction yield was maximised (170-190 g/L) using appropriate carbohydrates and acid excesses, while impurity concentrations were kept low (Fe<10ppm and Ca<300ppm) pre-treating the ores, using hydro-alcoholic leaching medium and different combinations of down-stream processes. In particular precipitation, solvent extraction and adsorption onto active carbon were tested to eliminate Fe and Ca from MnSO4 solutions.

Jan 1, 2003

By Vincent C. Smith, Agit Singh, Bernard Muller

The control of minerals processing plants is by no means trivial. In order to address some of the difficulties, it was decided to develop and test a model predictive controller (MPC) for a milling circuit. A milling simulator was written to test the MPC controller. Due to the large number of tuning parameters in a controller of this type, an optimising algorithm was written that automatically tunes the controller. Good, robust control was obtained when the controller was tuned using this algorithm. The controller was tested for various scenarios that are often encountered in the minerals processing industry. When problems were encountered, the MPC algorithm was specially adapted to accommodate for these difficulties. Control was further improved by using feedforward control as well as quadratic programming. The movement of the manipulated variables was reduced by using a region of uncertainty that allows the controlled variable to vary within a specified region around the setpoint. Integrators were handled by adapting the algorithm slightly and adding an optional integral error portion in the MPC controller. The performance of the enhanced MPC controller was compared to PI controllers on both the simulator and a commercial plant. The MPC controller showed faster responses with less interaction in both cases.

Jan 1, 2003

By Mike Daniel, Eric Wang

"Several new large copper and gold concentrators have been built and commissioned around the world in the past five to eight years. The success of the ramp-up from these very large concentrators has varied. CITIC SMCC Process Technology was engaged to assist some of these mines by gaining a better understanding of the factors that influence throughput capacity. As such, site-specific throughput forecast models that are influenced by SAG mill performance were developed. The forecast models are easy to interpret and modify and can greatly assist the mine management to make predictions and informed decisions for a range of site improvements. The models investigate the influence of SAG mill performance with respect to ore competency, derived from SMC Test® via the measured DWi model parameter. In some cases the benefits of blasting and from fine tuning milling operations are already incorporated into the "site-specific" forecast models. The methodology follows rigorous plant data analysis that is analogous to a "Mine-to-Mill®" optimisation project. The CITIC-SMCC model validation includes extensive data collection, which includes drill core analysis, ore characterisation and comprehensive comminution circuit operational data to assess the limitations within the comminution circuit within the operating mine. The results and models may be used to define the operating base lines of the processing areas and identify improvement opportunities upstream and downstream of the comminution circuit. The predictive capability of the models use logged production data and has enabled the user to differentiate between alternative circuit configuration options and identify optimum operating conditions. This approach minimises the ongoing requirement for costly plant surveys. The improvement strategy for each site, included the ongoing measurement of grindability, rock strength and via the Bond and SMC Test® respectively. Some commentary as to what other practitioners do with input data and their models is also presented as this highlights some of their shortcomings relative to the CITIC-SMCC methods."

Jan 1, 2014