Search Documents

By E. N. Levchenko, K. V. Bulatov, G. I. Gazaleeva

"The article highlights the new procedure of choosing special methods of disintegration for very complicated rare ores. Especially, there is a complex approach to criteria of comparing different types of crashing machines. Criteria are as follows: degree of crashing, degree of grinding, degree of slime creation and the new creations criteria for selection. The procedure is tested on tantalium and zelestinium ore. A new methods was shown the preference impact crashing machine MD-7 for zelestinium ore. In product of crashing 0,050 mm size are 9.4 %, 0,005 mm size – 2.5 %.This is gut result, and show the best indexes of slime creation. The check of the proposed new methods was done when comparing the crushing of tantalium ores of the Otboynoe deposit in cone inertial and centrifugal impact crushers and roller press. A research was conducted different crashing machines under laboratory and semi-industrial conditions. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion and degree of crashing showed that the centrifugal impact crusher (CC) and roller press (RP) has the lower indexes than the cone inertial crusher (CIC). Degrees of crashing for different crashing machines are:centrifugal impact crusher – 10.1;roller press – 10.8;cone inertial crusher – 14.2. The crusher CC the selection criterion is 0,632 units, RP – 0.730, where as for the crusher CIC – 0.848 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 0°, peripheral speed of a cone rotation – 1420 r.p.m, specific energy consumption- 4.99 kW*t/t. Crusher CIC-300? is the best for tantalium ores of the Otboynoe deposit. The new methodic are verification.INTRODUCTION Rare metal concentration circuits are complex, energy-intensive, and costly. The reasons for this include the multimetal nature of the rare metal ores, their volatile material composition and low grade. That is why careful selection of ore preparation circuits is of great importance for minimizing the energy inputs and maximizing the liberation of the valuable minerals. Recent research (Khopunov, 2011, Gazaleeva, 2015) has demonstrated that the most efficient comminution processes available to the mineral processing industry are selective disintegration, crushing and grinding, allowing to liberate the mineral particles along the cleavage in the comminution process. These methods are indispensable for the processing of finely disseminated refractory ores prone to slime formation. Many rare metal ores found in Russia are of this type."

Jan 1, 2018

By Kobus (J. J. ) Rossouw, P. Chris Pistorius, Johannes Sono

"Different coal properties are important in SL/RN (coal-based rotary kiln) direct reduction of iron ore, and in electrical smelting of prereduced iron ore. Laboratory simulation was used to evaluate two candidate coals, which were similar in volatile content and rank, but differed in reactive maceral content. The tests served to evaluate both the reduction rate (during direct reduction) and the dissolution rate of carbon from the coal into an iron bath.Reduction rates of mixtures of magnetite and devolatilised coal were assessed isothermally, using samples of 55 grams. The off-gas analysis was used to follow the extent of reduction. Results are shown in Figure 1 a). Coal B was expected to be more reactive, based on its higher content of reactive macerals (77%, compared with 61% for Coal A). In line with this, Figure 1 a) does show a higher reduction rate with this coal. However, increasing the reduction temperature increases the reduction rate substantially,especially for the less-reactive Coal A.For the dissolution experiments, samples (mass: 250 g) were melted in an alumina crucible (under a nitrogen atmosphere), to give a starting composition around 1%C. When the desired temperature was reached, 25 g of char was added on top of the melt, through a feeding port. Results are shown in Figure 1 b). The more-reactive Coal B was less crystalline (the graphite crystallite size estimated from X-ray diffraction was 4.6Å, compared with 11.4Å for Coal A). This is associated with a lower dissolution rate in iron."

Jan 1, 2003

By A. Koizhanova

Kumistinskoye gold- and silver bearing ores (Republic of Kazakhstan) as well as standardized test solutions containing gold, silver, copper, zinc and iron were studied. The best results in silver and gold recovery from Kumistinskoye gold- and silver bearing ores were achieved through use of complex cyanide-thiosulfate solutions as compared to individual cyanide solutions and thiosulfate solutions. It was found that such complex solutions substantially step up leaching process herewith increasing precious metals recovery rates. Thermodynamics of studied chemical processes was calculated. Reaction order, kinetic constant and activation energy of gold leaching process through use of cyanide-thiosulfate solutions were identified. We managed to prove that the sorption rates and holding capacity in process of gold anions recovery with anionite AM-2B are comparable to sorption characteristics for cyanide solutions. Keywords: gold, silver, copper, zinc, iron, cyanide-thiosulfate solutions, anionite AM-2B

Sep 1, 2012

By Xiao Ni

Alkyl hydroxamic acid was shown to be a suitable collector for the flotation of pyrochlore from carbonatite niobium oxide ores. In the direct batch rougher flotation from the ore without desliming, over 85% of the pyrochlore can be recovered at about 30% mass pull. Cleaner flotation tests showed that the rougher concentrate can be upgraded. The adsorption mechanisms of octyl hydroxamic acid (OHA) were studied by using high purity pyrochlore and calcite mineral samples and employing analytical measurements such as Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and UV/VIS spectroscopy. FTIR showed a shift of the vibrational frequencies of the carbonyl group in hydroxamic acid after adsorption on pyrochlore and calcite, and the shift was more pronounced on pyrochlore. XPS results indicated a lowering of the binding energies (chemical shift) of Nb3d5/2 and Ca2p3/2 electrons on pyrochlore, and the lowering of the binding energies of Ca2p3/2 electrons on calcite, again with the shift being more pronounced on pyrochlore. The results indicated hydroxamic acid formed stronger complexes with pyrochlore than with calcite. Adsorption isotherms indicated that OHA adsorbed more on pyrochlore than on calcite at low concentration. At high concentrations, the adsorption densities on both minerals were similar. All results explained the observed selectivity of the reagents in the flotation of the carbonatite niobium oxide ores.

Sep 1, 2012

By O. N. Mohanty, S. Mohan Rao, N. D. Rao, T. Mukherjee, P. V. T. Rao

"Tata Steel has its captive chromite resources at Sukinda, Orissa. They contain two ore types, i.e. (i) Ferruginous and (ii) Siliceous. The generation of off-grade ores is an increasing trend and simultaneously customer quality requirements are becoming ever more stringent. The ferruginous type ore also contains a considerable quantity of in-situ fines (~20% particles below 0.5 mm) that compound the beneficiation problem.In this paper, new strategies are discussed for producing additional value.added products after evaluating the present beneficiation practice in terms of changing market scenario, processing capability of the plant and ore characteristic. They would entail use of MGS - an enhanced gravity separator, for recovering additional products from plant tailings; production of ferruginous coarse concentrates (-3+0.5 mm with ~46% Cr2O3) using jigs; production of marketable grade lumpy (-40+10 mm size) concentrates from low grade siliceous ore using jigs and >2.8 Cr/Fe ratio siliceous ore fines treated in the Chrome Ore Beneficiation plant gravity circuit units and low intensity magnetic separator. The studies indicate that it is possible to recover 79-80% of the chromite, against a theoretical maximum of 82% from both the ore types, in the form of several marketable grade concentrates that would also include refractory grade."

Jan 1, 2003

By G. Bulut, Ü. Yenial

"Heavy metals contamination in aqueous systems can be found in a variety of industries, in particularly mining, metal processing, finishing and plating. Water containing more than 0.5 ppm heavy metal considered as a toxic due to harmful effects on health. The major techniques employed for heavy metal removal from industrial wastewaters include precipitation, reduction, ion-exchange, and adsorption. Adsorption is a heavy metal removal method for aqueous systems. As a common adsorbent, activated carbon has been used in treatment but it is ineffective on some elements. Thus, there has been a research for developing highly effective and selective adsorbents. In this study the adsorption of lead and arsenic ions on to coal waste and red mud waste was studied. The experimental parameters were determined as pH, equilibrium time and the initial concentrations, activation by heat treatment and the blend of adsorbents. According to their adsorption capabilities, red mud was found to adsorb lead and arsenic ion with high efficiency but coal waste did not adsorb arsenic ion. However the binary adsorptions of these ions were enhanced the adsorption efficiencies. In addition the blend of coal waste and red mud affected the adsorption efficiency. INTRODUCTION As a result of rapidly developing industry and excessive use of water resources, the need of clean water and wastewater management appear as a problem. Wastewater recycling activities and researches come to the fore for an effective use of wastewater. Recycling of wastewater, which contains heavy metals harmful to the environment and human, is a difficult process. Heavy metals are generally divided into three categories: toxic metals, precious metals, radionuclides. Wastewaters from various industries, containing heavy metals, are the main polluters of water and soil. Although their toxic structures, heavy metals are used extensively in industry as they have technological significance. Usually mining industry, metal industry and industrial organizations produce heavy metal containing wastewaters (Volesky 1990, Ting and Lawson 1991, Bishop 2002)."

Jan 1, 2018

By Fengnian Shi

In the current energy-sensitive world, sustainable development in the mineral industry will require new, better and more efficient processes. Novel comminution methods, which offer the prospect of achieving the required outcomes of size reduction and mineral liberation at lower energy consumption, are continually being sought. In the past five years, extensive research using high voltage pulse electrical comminution technology has been carried out at the Julius Kruttschnitt Mineral Research Centre (JKMRC), in collaboration with selFrag AG. The major outcome of this research is the development of the concept of pre-weakening ore particles by electrical comminution procedures to reduce the energy consumption in the downstream grinding circuit. The research has also verified the preferential liberation of valuable minerals by electrical comminution. Given the advantages, several potential applications of electrical comminution in the mineral industry are proposed, including AG/SAG mill feed pre-weakening, pebble treatment, ball mill feed pre-weakening, early recovery of the liberated valuable minerals, crack/micro crack generation for improved leaching, and smelter slag treatment. For the mineral industry to utilize electrical comminution, two emerging issues identified from the research need to be address. They are the energy consumption by electrical comminution in the locked cycle treatment and the facilities scale up necessary to move this technology from the laboratory to the plant. Keywords: high voltage pulses, electrical comminution, energy efficiency, mineral liberation

Sep 1, 2012

By Manuel Diaz

"In these difficult times for the mining world, mainly due to the global uncertainty about metal prices and the increased activity of opponents to the mining industry, it is essential that mining companies focus on efforts and strategies that will give them the most flexibility to succeed under the fury of these phenomena. The careful management of systems to control costs, and indicators to measure with great precision actual variations in costs and cash flows, are essential to adequately manage the uncertainty. Similarly, clear corporate and regional strategies designed to maximize cash flow and operating margin will allow the company to be better prepared to face any negative situations caused by declining metals prices, stricter government regulations and increasing social pressure. Gold Fields Limited, a corporation of South African origin and with more than 100 years in the gold mining business, has developed the ability to adapt to large changes generated by different global crisis throughout its history. This occasion will be no different. Given the critical situation of the mining industry in the world today, Gold Fields has embarked on a re-structuring plan at global level that will allow much closer control and real efficiency of production costs. This plan includes the creation of regional business units that allow greater independence for each region while still preserving the standards and cultural values of the Corporation. This presentation will explain why we believe that this approach combines the best aspects of the two styles of business, and what are the expected results. In the Americas Region, Gold Fields currently operates Cerro Corona, in Peru. In addition, the company is considering opportunities for growth in Chile, Brazil, Mexico and Canada."

Jan 1, 2014

By M. Alvarez-Silva

The control of the amount of chromite reporting to the concentrate during the flotation of UG2 ore is of critical importance since its presence affects the downstream smelting process. It is generally reported that the main mechanism responsible for chromite recovery is through entrainment. This is reflected in analyzing the solids and water recoveries. These in turn are strongly dependent on the froth phase. In the present investigation a laboratory scale column flotation cell was used to investigate the role of the froth phase in the flotation of UG2 ore. Such a device is superior to a standard batch cell since it operates at steady state in open circuit and also allows for a greater degree of flexibility in terms of froth heights. The mass of solids and water recovered in the concentrate as well as chromite (Cr2O3) recovery by size class was determined as a function of froth height, superficial gas velocity and depressant dosage. The results showed that depressants had little effect on chromite recovery but increased the grade due to the depression of gangue minerals. A 60cm froth height always resulted in slightly lower solids, water and chromite recovery than for 30cm. Typically only 20-25 % of solids reaching the pulp-froth interface reached the launder. The relationship between solids and water recovery for a wide range of conditions indicated that chromite is mostly recovered by entrainment. Keywords: UG2 ore, column flotation cell

Sep 1, 2012

By Jiajun Geand, Shuli Wang, Baodong Pan, Xueqi Cui, Guangwei Zhang, Jipeng Sun

Gravity-fed three-product dense medium cyclone(GTDMC)is usually used as the main coal washing equipment in coking coal preparation plant. It can produce three products with a low density suspension at the same time. Raw coal and dense medium are fed separately into the cyclone. Only the qualified low-density medium suspension is pumped into the cyclone while the raw coal is fed into the first-stage 1200mm cyclone axially at the top end by gravity. The 1200mm cyclone with a cylindrical form is for low-density separation. The clean coal with light density and slower-settling velocity moves directly towards the low pressure zone along the axis and is carried through the vortex-finder to the overflow. Only the heavy products pass through the "separating zones" to the wall of 1200mm cyclone and then migrate into the series-connected second-stage 850mm cyclone through the tangential outlet. The medium suspension from the first-stage cyclone is thickened and contains more magnetite coarse particles. The second-stage cyclone typically consists of a cylindrical section and conical part. These are all favorable for the second-stage cyclone to separate at a high density. Production practices show that the clean coal and the gangue rarely mixed in the middling, the lower limit of the separation is 0.2 mm, the Organic Efficiency and the Ecart probable of the first stage is 98.30% and 0.026 kg/L respectively.

Jan 1, 2014

By Willis Forsling, Prabhakar Swarna, Hanumantha Rao Kota

The solubility of wollastonite and its Hallimond flotation behavior as a function of dodecylamine concentration and pH are examined. The flotation response is characterized by adsorption and surface energy in the presence of amine. The methods of UV-Visible and FT-IR spectroscopy for adsorption and sessile-drop contact angle for surface energy estimation are employed. The results of wollastonite dissolution clearly showed its non uniform dissolution. The surfaces are depleted with calcium ions and became rich in silicon within 10 min of flotation time. Maximum flotation of wollastonite corresponds to a half monolayer coverage of amine, which is substantiated by the surface energy parameters. A good correlation between flotation, adsorption and surface energy as a function of amine concentration and pH was observed. The sudden increase in wollastonite flotation and amine adsorption at and above 5x10-5 M initial amine concentration is thought to be due to two-dimensional precipitation of amine on surface in accordance with the recent 2D-3D precipitation model of amine adsorption on silicate minerals.

Jan 1, 2003

By Yuri Yemelianov, Stanislav Balikov, Alexander Epiforov, Andrey Boldyrev, Andrey Bogorodsky

"Test work was carried out using copper gold-bearing flotation concentrate with 6.85%Cu, 14.30%Fe, 20.70%S and 2.34%As. Gold and silver grade in the concentrate is 54.6 g/t and 92 g/t, respectively. Gold and copper are valuable components in the concentrate. Gold is partially associated with pyrite and fahlores. Copper in the concentrate can be found as tennantite (Cu12As4S13). The 71% of gold from the flotation concentrate is recoverable by cyanidation with simultaneous cyanide consumption in the amount of 96 kg/t. The major reason of refractoriness is that gold is fine encapsulated into sulfides and the presence of cyanicide-copper. The concentrate ground as much as 95% minus 10 µm was treated using low-temperature POX at the temperature of 100±5°C, L:S ratio of 5:1 and the process time of 1-5 hours. Residual sulfide sulfur in the cake is 2.28% which is 89% sulfide oxidation. The highest copper recovery to POX solution is 91%. It was found that gold recovery to cyanide solution is 85-94% during alkaline pre-treatment of POX cakes followed by cyanidation. In this case, cyanide and lime consumption is 75-90 kg/t and 120 kg/t, respectively. In order to recover precious metals from POX cakes leaching using sodium sulfite was carried out. Test work was conducted at varied reagent concentration, L:S ratio and leaching time. Gold and silver recovery achieved was 85-95% and 59-63%, respectively."

Jan 1, 2014

By T. Surkova

For the moment reserves of high-grade ores are practically depleted requiring ever-increased involvement of low assay raw materials, such as black-shale ores, in industrial operations. Black-shale ores are constituted of minerals containing such valuable components as vanadium, uranium, molybdenum, manganese, and rare-earth elements (REE). We studied technogenic solutions of black-shale ores processing, after uranium, molybdenum, and vanadium were recovered. Mentioned solutions contain rare-earth elements in substantial quantities (S REE 70-100 mg/dm3) that is very important factor taking into consideration the world demand ever-increasing last years. Higher concentrations of iron and aluminum inhibiting REE sorption and extraction recovery are found in solutions. We propose a method of hydrolytic deposition to cleaning solutions from impurity elements (Fe, Al). Study of hydrolytic deposition kinetics allowed identifying optimal conditions to run this process. Rare-earth elements may be recovered from purified solutions through sorption process followed by their further deposition from eluates in form of concentrates. Keywords: black-shale ores, rare-earth elements, a method of hydrolytic deposition, impurity elements, sorption

Sep 1, 2012

By Rodrigo Carvalho, Marcelo Tavares

"The accurate prediction of the outcomes in SAG grinding has been a great challenge to researchers and process operators. The use of Discrete Element Methods for modelling charge motion in tumbling mills allowed extraction of not only visual data, such as the position of the charge, but also the energy transfer in terms of the energy dissipated in the collisions. One of the advantages of DEM technique is its scalability to different mill sizes and some operational conditions such as speed and mill filling. Recently the Authors proposed the coupling between DEM outputs and modified Population Balance Models that with proper dedicated ore characterization tests allows the prediction of the outcomes of an energy transfer example. This modelling framework is called the Multi-scale Mechanistic Modelling. This paper shows the application of the Multi-scale Mechanistic Model to a set of pilot plant tests ran at different operational conditions. The prediction of the grinding outcomes and even the stabilization of the charge was achieved by the use of the Multi-scale Mechanistic Modelling framework. This approach has a great potential to become a powerful tool to design and optimize AG and SAG mills."

Jan 1, 2014

By Magnus Evertsson, Rebecka Stomvall, Josefine Berntsson

"Understanding the effect of particle shape on dry rheology is considered to be an important aspect in order to replace natural sand used in concrete with manufactured sand. Crushed particles from solid rock are normally less rounded and have less equally shaped dimensions compared to natural sand. Thus, the flowability and workability of the concrete will be different. In previous research, it has been demonstrated how different crushing techniques affects the shape of the particles. In many cases it is believed that Vertical Shaft Impact (VSI) technology is a way forward to replace natural sand. To be able to study the effect of VSI at the smaller fractions (63-2000 µm) sufficient measurements methods to determine particle shape are required. Optical tools to analyze the aggregates would make it possible to study a large amount of particles at small fractions. The determination of particle shape of aggregates is challenging since the shape is highly irregular and the size span of particles are very large. This study aim to evaluate one of the available optical tools, the Camsizer, for digital imaging determination of shape and size distribution. The available default shape parameters of the Camsizer are studied to understand the meaning of the parameters and their suitability for determining the quality of manufactured sand. To evaluate the capacity to determine particle shape, tests are made with 35 different materials. The results are compared with the dry rheology measured with the standardized "flow cone" test. Dependence has been previously proven between particle shape and the mass flow rate in the cone. Three different shape parameters, aspect ratio, sphericity and symmetry, are studied with the Camsizer and the results are compared with the mass flow rates in the cone. The results indicate a strong linear relationship between the optical parameters and the flow cone test."

Jan 1, 2014

By J. D. Miller

The more efficient production and use of mineral resources is a major objective of our sustainability efforts. Resource characterization is a critical component for optimization of the mine-to-mill process, including innovative processing for sustainable growth. Such characterization is now referred to as geometallurgy, with advanced instrumentation including, for example, particle size analysis, XRF, XRD, NIR, automated SEM/EDAX analysis (QEMSCAN, MLA), and high resolution X-ray micro tomography. Geometallurgical information is important for exploration, deposit evaluation; mine planning, design and analysis of separation processes, etc. Characterization of mineral processing particles in 3D is now possible using high resolution X-ray micro tomography (HRXMT), and such HRXMT systems have been installed at several laboratories around the world. After review of principles, the features of such HRXMT analyses are presented including size/shape, damage state, mineral phase identification, and evaluation/isolation of trace mineral particles. With new algorithms for image analysis, quantitative data treatment is possible for construction of liberation-limited grade/recovery curves, for the determination of specific crack surface area, and for complex texture analysis including grain exposure. Finally, new tomographic characterization possibilities are discussed to provide the foundation for the development of advanced, innovative processing strategies for sustainable growth. Keywords: X-ray tomography, resource characterization, HRXMT, particle size analysis XXVI INTERNATIONAL

Sep 1, 2012

By Dmitriy Makarov

The paper presents the modeling and analysis of oxidation of pyrite copper-zinc ore samples from the Letnee, Yaman-Kasy and Valentorskoye deposits. It is found, that the oxidized samples contain copper and zinc sulfates that are leached under the sample and water contact. It is shown, that sulfide floatability is decreased by the longer-term oxidation.We advise to improve nonferrous metals recovery by joint leaching and ultrasonic treatment of oxidized compounds. Study of the geotechnological processes of non-ferrous metal extraction, on the basis of two copper-zinc ore deposits shows, that heap leaching is of little use for the ores of the Letnee deposit. Leaching results for the Yaman-Kasy ore showed more promise.

Sep 1, 2012

By P. V. Ramesh Babu

India has sizeable number of small deposits of rare metal bearing minerals namely columbite-tantalite, pyrochlore, beryl, lepidolite, spodumene and rare-earth element bearing minerals monazite and xenotime in different parts of India. Pegmatites, alkali granites, syenites, and the derived gravel and soils are the main source for rare metal and rare earth (RMRE) minerals. The RMRE minerals are classified as prescribed substances under Atomic Energy act of 1962 keeping in view the uses in the nuclear industry. Atomic Minerals Directorate for Exploration and Research (AMD) of Department of Atomic Energy (DAE) is the sole agency responsible for exploration and exploitation of RMRE minerals in India since 1962. The latest technological advancements and applications in the field of space, electronics, communication and nuclear industry using these metals and their products have necessitated to augment the production and resources of RMRE minerals. These minerals play a significant role in the technological and economic development of the country. The light rare earth element bearing mineral monazite is abundant in beach sands and is being commercially exploited by Indian Rare Earths Limited (IREL). Columbite-tantalite, the chief source for niobium and tantalum (Nb-Ta) metals present in the pegmatitic gravel are recovered by small mobile beneficiation plants. The cut and fill method of mining adapted is eco-friendly. The processing flow-sheet consists of wet sizing at ½ in and 1mm followed by gravity concentration of sized products utilizing the methods of jigging and wet tabling. The sizing equipment include revolving and vibratory screens and the gravity concentration equipments used are fixed sieve jigs and movable screen jigs for final upgradation. The gravity concentrates are further upgraded by magnetic separation to remove magnetite and ilmenite. The mine areas are reclaimed by filling with coarse size tailings and new plantations. These mobile pilot plants were earlier operated in Bihar mica belt, Jharkhand, pegmatitic areas of Karnataka and Nellore mica belt of Andhra Pradesh and are currently being operated in Bastar-Malkangiri pegmatite belt of Chhattisgarh and pegmatites of Jharsuguda district of Orissa. Beryl, lepidolite, spodumene and cassiterite minerals are the by-products from the pegmatite ores. Fergusonite, samarskite and microlite are the other niobium and tantalum bearing minerals which are also found in pegmatites. Xenotime, the chief mineral of yttirium generally occurs in granites and pegmatites. The rare earth minerals monazite and xenotime get concentrated in the placer sands of rivers and beaches. The occurrence of xenotime in the sands of Siri River and Deo River in Chhotanagpur granitic terrain in parts of Chhattisgarh and Jharkhand are an example. These sands containing 1-2.5% heavy minerals were processed by a mobile plant consisting of sizing equipments like trommel and vibratory screen followed by separation of heavy minerals from -1mm sands with the help of gravity concentration equipments like spirals/shaking tables/sluices. Xenotime and monazite from the pre-concentrate are further separated by magnetic and electro-static methods. The present paper illustrates the pilot plant set up for the recovery of rare metal as well as rare earth minerals. Keywords: small deposits, rare earths, rare metals, pegmatite, Nb-Ta, xenotime, India

Sep 1, 2012

By A. A. Lavrinenko

There are discussed the possibilities of using of flotation tailings of platinum-copper-nickel sulfide ores of the Norilsk region for the preparation of backfill mixture instead of a specially produced rock and binder materials to reduce the cost of stowing operations and impact on the environment. It is shown that due to the presence in the tailings of flotation up to 10% of sulfide sulphur, which reduces the strength of the fill materials, and more than 1 g/t PGM it is necessary the preliminary extraction of the sulfides in the product for further processing that give an opportunity to reduce the losses of valuable components. It is shown that by the flotation of the current tailings it is possible to extract 91% of sulfide sulphur, 60% of palladium and 30% platinum in 17% sulfide concentrate containing 2.1 g/t palladium, and to reduce the sulphur content in the tailings up to 0.7%. Due to the easy oxidation of pyrrhotite, there is recommended fractional delivery of the collector with a total consumption 200 g/t. There are discussed results of the flotation study with an additional collector of PGM (sodium diizobutyditiophosfinate), which one show the possibility to increase extraction of platinum on 45%, as well as extraction of sulphur and palladium. For the flotation of sulfides and PGM from the current tailings there is recommended a combination of collectors for primary flotation and only butyl xanthate using in control operations. The possibility of using sludge fraction of the current tailings as a component for the preparation of the combined cementing materials after exposure of sulfides is analyzed. It is shown that the efficiency of the flotation of sulfides from this fraction can be enhanced using selective flocculants. There are discussed the advantages of implementation of completely hydrophobic butadiene-styrene copolymer in comparison with partially hydrophobic polymers. There is discussed an efficiency of the mechanochemical treatment of old tailings in turbo mill and sulphuric acid to remove oxide films from the surface of pyrrhotite before its flotation. Due to the pretreatment operation there is achieved increasing of sulphur extraction and after the introduction to the flotation circuit three control operations there is produced the fill material with sulphur content 2.5%. Keywords: tailings, copper-nickel ore, pyrrhotite, butyl xanthate, sodium diisobutyl dithiophosphinate, selective flocculation, butadiene-styrene copolymer, mechanochemical treatment

Sep 1, 2012

By Miguel Becerra, Daniel Jordán, Jorge Soto, Luis Torres

"Most SAG grinding operations currently use ball sizes between 5.5 and 6 inch maximum size. However, in most cases the use of this ball sizes hasn’t been justified by a phenomenological analysis of the real effect on the grinding process, but rather by trial and error. The analysis of the influence of ball sizes in SAG grinding hasn’t been developed in detail by considering the effect on process parameters inside the mill, grinding efficiency or internal classification. Historically a conventional grinding reference has been made on the empirical procedure developed by Azzaroni (1980). Further to Azzaroni’s methodology, Sepulveda (Sepúlveda, 2007) developed the SPEC methodology, incorporating the ball size effect on the grinding efficiency parameters using a population balance model included on Molycop tools spreadsheets.This paper demonstrates a detailed analysis at pilot scale of the ball size employed in SAG grinding and scaling that exists between the different levels. This analysis includes assessing the effect of balls sizes on parameters associated with grinding efficiency and its effect on the total fill level, product size distribution and specific energy consumption, among others. In a complementary way it develops a technical - economical evaluation from industrial data comparing two different ball sizes and its effect on the grinding process analysed integrally."

Jan 1, 2014