Search Documents

By RB. Pedersen, T. Barryere, E. Reeves, A. Stensland, I. Thorseth, T. Baumberger

Venting on ultraslow spreading ridges is far more abundant then previously predicted, and the discrepancy between observed and predicted vent field density may imply that non-magmatic heat sources are common along these ridges (Baker and German, 2004; Escartin et al., 2008; Rona et al., 2010; German et al., 2016). In this study we have estimated the flux from two hydrothermal vent sites situated on the slow to ultraslow spreading Mohns Ridge at the Arctic Mid-Ocean Ridge system (AMOR). The flux estimates have been made using the primordial isotope 3He in the non-buoyant plume above the Loki’s Castle vent field at the northern termination of the Mohns Ridge, and from the Jan Mayen vent fields area situated close to the southern termination of the ridge. Primordial 3He enters the oceans through degassing and mixing with hydrothermal fluids eventually to be discharged at the ocean floor primarily at hydrothermal vent sites and submarine volcanic eruptions (e.g. Clarke et al., 1969; Lupton and Craig, 1981; Lupton, 1998). Once introduced into the water column the concentration will only decrease by dilution due to its conservative behavior in the water column. Water column samples were collected using a CTD (conductivity, temperature, depth) probe (911plus Seabird) with a Niskin water bottle rosette. The water column above the Jan Mayen vent fields (JMVF) was sampled in the years 2006, 2011, 2012 and 2013 (82 samples) and the water column above the Loki’s Castle vent field was sampled in the years 2007, 2008 and 2009 (116 samples).

Jan 1, 2018

By J. R. Woolsey

The cost of an offshore exploration project is mainly dependent on the size of the vessel engaged for the work and increases dramatically with increasing size. Of the various factors influencing vessel size, the type and size of the sampling equipment is typically the principal consideration. This scenario is particularly true of shallow sampling programs employing a vibracore system. The problem develops when certain bottom materials such as densely packed fine sand require sampling. This type of material being one of the most difficult for the standard vibracore systems, with integral core liner, to penetrate to a reasonable depth of some five to seven meters. The problem is mainly related to the excessive cross sectional area of the cutting bit required to accommodate the core liner. The typical solution has been to apply more power to the vibracore drive head which results in a considerable scale-up for the entire system with attendant increase in vessel size. In order to reduce operating cost, M.M.R.I. has developed several systems for deployment from vessels in the 20 meter range. Two systems are modifications to the basic vibracore and a third is a vibralift system. Basically, one of the vibracore units is employed where core liners are required, utilizing a special jet bit designed to reduce the cutting pressure on the bit while not affecting the integrity of the core. The other designed for core extrusion on

Jan 1, 1986

By M. F. Dibble

The technology available for mining of underwater mineral resources such as placers and phosphorite, typically occurring with variable amounts of overburden, has remained largely unchanged for decades. The traditional bucket ladder dredge with maximum digging depth of 48 m and monthly capacities about 500,000 m3 still reins as the only heavy duty mining system capable of working the tough materials characteristic of heavy metal placers. Attempts at adapting the bucket wheel cutter-suction dredge to these severe conditions have not yet been successful except in moving small volumes from shallow depths. High capital cost (20-30 million U.S. dollars), high cost of overburden removable, and turbidity generation for the bucket ladder are often significant negative factors in mining operations where this system remains the only viable alternative. The Japanese continue to advance the technology of their submersible dredge pump system powered by specially adapted, direct drive electric motors. Present systems are designed primarily for working surficial deposits of aggregate to depths as great as 90 meters, the pump suspended by cable from a surface vessel with an eductor pipe leading from the pump to the vessel. Such a system may prove adaptable to a variety of surficial deposits including phosphorite, shell and heavy minerals in addition to aggregate. However promising for the exploitation of surficial deposits, little advantage can be expected for the deeper buried and more difficult deposits.

Jan 1, 1986

By Peter M. Bartlett

The Republic of South Africa ranks among the world leaders in both reserves and production of numerous land-based mineral commodities. Over the last three decades, however, South Africa has also identified several commodities that may exist in commercial quantities in the marine environment. The major targets include 1) placer diamonds; 2) titanium- and zirconium-rich beach sands; 3) sedimentary and concretionary phosphorite and glauconite deposits; 4) manganese nodules; and 5) hydrocarbons. South Africa ranks second in world reserves of diamonds and has potentially enormous sea resources. Diamonds are currently recovered on the Atlantic side from ancient beach gravels in the Northwest Cape Province and from the seabed south of the Orange River to Lamberts Bay. Approximately 100,000 carats (or just 1% of South Africa's total annual production) are produced each year from offshore operations. DeBeers is investing approximately $5 million per year on sea prospecting activities and currently operates three vessels in offshore recovery operations. Diamonds recovered at sea will remain a small percentage of total production because of huge land-based reserves that are mined at a fraction of the cost of seabed operations.

Jan 1, 1986

By D. S. Cronan

Mineral exploration problems in the S.W. Pacific are not unique to that region, but a combination of favourable circumstances render it an ideal area to attempt to solve such problems. The land area of the S.W. Pacific island nations is only a fraction of the total sea area they can claim under current International Law. Hence, they have a great need to explore and evaluate their offshore areas. For the past ten years the focus of this work has been CCOP/SOPAC which has individually and jointly with other groups initiated and maintained far reaching marine mineral exploration programmes. In association with CCOP/SOPAC the writer has obtained and analysed approximately 650 sediment samples from the S.W. Pacific region for seventeen elements. Multivariate statistical techniques have been applied to the data set. The aim has been to identify chemically anomalous sediments reflecting either sea floor mineralisation and/or mineralisation on adjacent land areas.

Jan 1, 1985

By Charles L. Morgan

For the past twenty years or so the oceans of the world have been transformed in the minds of most Americans from the ultimate and nearly infinite receptacles for sewage and other wastes to an almost sacrosanct and threatened last refuge of Mother Nature from man on Earth. While this general movement has helped somewhat to moderate the flows of pollutants into the oceans, it has had severe and sometimes devastating impacts upon various attempts to develop seabed mineral resources. Marine mining proposals have been easy targets for attack. In most cases, they have short or no histories and involve prototype or first-generation methods. They commonly lack major financial backing, and do not command significant public support. Their constituents are limited. Opposition movements to such proposals have been able to evoke strong support by appealing to this "last refuge" image and depicting mining operations as the final assault. In mounting these public appeals, the movements obtain visibility and support. Because of the small and sometimes tentative status of the constituencies which support particular proposal s, the potential liabilities for opposition movements are minimal.

Jan 1, 1989

By J. R. Woolsey

In late 1988, the Committee for Coordination of Joint Prospecting for Mineral Resources in South Pacific Offshore Areas (CCOP/SOPAC), Suva, Fiji, consulted the Continental Shelf Division of the Marine Minerals Technology Center regarding low-tech, low-cost, reconnaissance sampling systems for a variety of nearshore needs. Materials of interest to several member island nations included silica and calcareous aggregate for cement manufacture, sand for beach replenishment, heavy minerals, and precious metals. A principal criteria of the system was that it be of low-tech design, and as far as possible, suitable for construction on the islands from available materials. It should also be operable with SOPAC personnel on island vessels of opportunity. The system selected to satisfy these requirements was a convertible drill of basic airlift design, capable of operating with easy modification as either a vibralift or airlift, depending on the desired application. The basic system included a drill pipe constructed of heavy duty 76 mm (3") black iron pipe, divided into three 3 meter sections (for ease of transport), fitted with an air intake manifold and bit at the lower end. A 25 mm (1") galvanized pipe assembled in three similar sections and clamped to the drill pipe served as a water jet to assist in cutting. Air was supplied to the manifold by means of a 12 mm (1/2") pipe also clamped along the length of the drill pipe. Suitable hoses supplied water and air to the upper ends of the respective pipes by means

Jan 1, 1989

By Tracy Shimmield

Deep sea tailings placement (DSTP) techniques have been pioneered in Papua New Guinea (PNG): a mining reliant economy in a seismically active region, facing major environmental challenges in the safe handling and storage of mine tailings on land. Scientists at SAMS have researched impacts of DSTP on the marine environment specifically to inform and develop guidelines for the use of DSTP to reduce environmental impact, thereby lowering risk and increasing private sector investment. Guidelines have been established as regulation by the PNG Government providing reassurance to private investors, facilitating an increase in mining exports to 60% of total export. Researchers investigated the effects of DSTP at 2 PNG mines: Lihir Gold Mine which has been actively discharging tailings since 1996 and Misima Mine, closed in 2004 after discharging tailings for 15 years, allowing an assessment of the recovery of the marine environment after tailings placement. Research involved investigating ocean currents and mixing, the behaviour of metals and the effect of tailings on benthic communities including the risk of elevated metal contents entering the food chain. The research established a metal ?fingerprint? of tailings compared to natural sediments, which enabled the transport of fine tailings within the deep ocean to be ascertained.

Sep 14, 2011

By Glen Smith

Nautilus Minerals is the world leader in exploration and development of deep ocean seafloor massive sulphide (SMS) resources. The company is currently focused on generating its resource pipeline in the Western Pacific and its first development project for recovery of high-grade copper, gold and silver mineralisation from its Solwara 1 site in the Bismarck Sea, Papua New Guinea. The Solwara 1 site is located at a water depth of 1,600 ? 1,800 meters. Over 150 SMS seafloor surface samples have been collected from chimney structures during dives made by remote operated vehicles (ROVs). In order to obtain an understanding of the sub-surface mineralisation, Nautilus carried out 4 drilling programs between 2006 and 2010 which allowed the calculation of a Canadian NI43-101 compliant resource estimate. The initial 2006 campaign was based on conventional offshore surface driven drill equipment. In conjunction with the subsea remote technology industry, Nautilus subsequently developed an ROV operated seafloor drill system with improved drill core recovery and efficiency. This technology was developed further with a 2010 - 2011 drill program to increase the available geological knowledge at Solwara 1 and adjacent prospects. his paper will provide an overview of Nautilus? SMS drilling requirements and recap the evolution of drilling technology and operations undertaken at Solwara 1 from 2006 to 2011. The paper will also discuss the potential of further developments in drilling techniques and equipment to increase or improve drilling depth, efficiency and data quality.

Jan 1, 2011

By James C. Barker

Concern over the availability of domestic critical and strategic mineral supplies has led the Bureau of Mines to evaluate the reserve development potential of alternative sources in Alaska. Near the village of Platinum, on the southwest Alaska coast, the Red Mountain concentrically zoned ultramafic complex is a source of onshore alluvial placers containing platinum-group-metals (PGM). It has long been suggested that valuable placers may also underlie the shallow coastal waters of the Bering Sea. A direct correlation of placer PGM and chromium to ultramafic rocks in the area was studied by the Bureau and the extent of the complex was mapped. Magnetometer and gravity data and geological studies suggest the complex is a large lensoidal body trending several kilometers offshore to the southwest with a probable steep southeasterly dip. Multiple Pleistocene glaciations and marine transgressions have eroded the western and southwestern portion of the complex. Sediments containing PGM, chromium, and associated gold (largely derived from glacial till) have been transported northward along the advancing coastline by littoral currents. Beyond the breaker zone, these sediments are generally buried by recently winnowed sand and gravel transported by strong longshore tidal currents. There is also evidence that paleoplacer channels underlie the marine sediments.

Jan 1, 1986

By Andrew E. Grosz

The United States is dependent on foreign imports for about 80 percent of its ilmenite, about 60 percent of its rutile, and virtually all of its monazite. Nearshore marine sand deposits and beach-complex sediments in the southeastern United States are important domestic sources of ilmenite, leucoxene, rutile, zircon, monazite, and a number of other less well known economic heavy-mineral (HM) species. Because global onshore reserves of placer titanium minerals may fall short of demand in as few as 20 years, offshore research in HM placers will become more important. The Atlantic Continental Shelf (ACS) defined by the shoreline and the 200-m isobath varies in width for the modern U.S. coastline from a fraction of a kilometer to about 150 km offshore of Cape Cod, Mass., and includes an area of about 3.91 x 105 km2. It probably contains 3-7 x 1011 m3 of sand and gravel which may locally contain commercially exploitable placer HM deposits.

Jan 1, 1986

By Willam R. Normark

During a series of dives with the submersible ALVIN in 1984, samples of massive sulfide were recovered from four vent sites. All sites occur within a linear, steep-walled cleft about 50 m wide and as much as 30 m deep. The cleft bisects the axial valley floor throughout the 15-km-long study area and appears to have been the source for the most recent volcanic eruptions in the valley. Three of the vent sites are defined by a set of discrete hydrothermal discharge zones; as many as eight have been identified over a distance of 500-800 m along the cleft floor. Sulfide deposits occur as individual and coalesced mounds, spires, and chimneys generally less than 3 m in height but a few might be as high as 10 m. The vents are also marked by extensive, yellow-to-amber ferruginous sediment and clots of bacterial matter. Some vents have extensive colonies of tube worms, gastropods, mollusks, and several predator species, such as crabs and squid. The fourth vent site has no visible discharge and consists mainly of "dead" spires and chimneys of massive sulfide. The massive sulfide samples collected with ALVIN are primarily sphalerite with minor marcasite, pyrite, pyrrhotite, isocubanite, chalcopyrite, wurtzite, and anhydrite. Bulk analyses of these chimney and spire samples show Zn contents approaching 60% by weight and significant enrichments in Ag and Cu. Vent fluids have the highest concentrations yet reported for Zn, Fe, and Mn. Thus, the Zn- and Ag-rich nature of massive sulfide from the southern Juan de Fuca Ridge study area

Jan 1, 1985

By John Noakes

Marine scientists at the University of Georgia, have in the past few years, designed, developed and refined two geochemical survelliance systems for the exploration of hard mineral resources on the seafloor. The one first developed is an underwater sled which contains a nuclear radiation detector for measuring naturally occurring gamma radiation that is associated either with marine phosphorites containing uranium and its decay daughters or thorium decay products that are indicative of monzanite. The latter can, in most instances, be used as a pathfinder mineral for placer deposits that may contain other heavy minerals of interest such as rutile, ilmenite, chromite, gold, etc. This sled is operational in continental shelf depths. The second system is capable of more definitive measurements in the form of direct elemental analyses of the silt and clay fractions within the surficial sediments. It consists of a towed sled containing a submersible pump which, upon agitating the sediments, transfers the finer fraction up a hose to a shipboard centrifugal cone then to an automated sample processor. The resultant samples are rendered into sediment wafers, suitable for non-destructive XRF analysis. The system is capable of shipboard analysis for specific elements within minutes after sampling, allowing a cursory look upon which an exploration grid can be formulated while on site. A much wider spectrum of up to 40 elements can be evaluated when the wafers are returned to the land based laboratory.

Jan 1, 2011

By Mark Lee, Isobel Yeo, Sarah Howarth, Christian Millo, Javier González Sanz, Paul Lusty, Bramley Murton, Pierre Josso

"Seafloor cobalt-rich ferromanganese crusts represent the most important yet least explored resource of ‘E-tech’ elements on the planet (Hein et al. 2003; ISA, 2008; Hein et al. 2010; Hein et al. 2013). These polymetallic deposits form a continuum from nodules rich in manganese and cobalt to crusts rich in tellurium and the heavy rare earth elements (HREE). It is this combination of traditional (base) metals and the extreme enrichment of ‘E-tech’ elements that makes seafloor ferromanganese oxide deposits particularly interesting to both science and society. Recent estimates of the global resource, based on the sparse data available, infers a dry mass of ferromanganese crusts on the seafloor of 35 x 109 tonnes (35GT). Of this, 3.7 GT is predicted in the Indian Ocean, 8 GT in the Atlantic, and 23 GT in the Pacific (Hein et al. 2013).At a global scale, the processes controlling the formation and distribution of ferromanganese (Fe-Mn) crusts are reasonably well understood (e.g. Hein et al. 2000; Verlaan et al. 2004; Cronan 2006; Halbach et al. 1989; Usui and Someya, 1997; Hein et al. 2000; Hein et al. 2003; Hein et al. 2009; Hein et al. 2010; Hein et al. 2013; Muiños et al. 2013; Marino et al., 2016). However, much of this knowledge is drawn from sparse sampling at a regional to ocean basin scale. As a result, there remains a fundamental gap in understanding of the role of local-scale factors, such as micro-topography, ocean currents and upwelling, sedimentation rates, micro-organisms, water mass composition and biological productivity, that are considered potentially crucial to controlling the growth and composition of Fe-Mn crusts. Indeed, quantitative, particularly temporal, information relating to these processes and their relative importance in deposit formation is almost completely absent. Hence, to make any significant advance in understanding these deposits require significant new research."

Jan 1, 2017

By Charles L. Morgan

In a commercial effort to characterize deep seabed manganese deposits in the Clarion-Clipperton region of the northeastern tropical Pacific, Ocean Mineral s Company carried out 16 expeditions to the region between -1978 and 1981. During these cruises OMCO collected substantial data. Activities included acoustic profiling, video and photographic imaging of the seabed, and sampling of the deposits with dredges, box cores and free-fall grab samplers. In 1990 the samples, photographs, technical reports and computer data bases which resulted from this work were archived at the Marine Minerals Technology Center at the University of Hawaii. This preliminary examination of the collection focuses on the biological observations made from almost 10,000 photographs of the seabed and the manganese nodule size distributions and compositional data from the free-fall grab recoveries. Regional trends are evident in all three data types. The biological examinations of the seabed photographs show significant geographical trends, with greater abundances of organisms being noted in the northeastern extreme of the region, decreasing toward the southwest (11.4 to 2.7 observations per 100 m2; 460 to 190 g per 100 m2). The nodule size distributions suggest that the ratio of the nodule burial rates to growth rates systematically decreases over the same range (0.65 to 0.36 nodules buried per 1 cm of growth). Preliminary geostatistical analysis of the ore grade data show that, in addition to high local variability, some deposit

Jan 1, 1991

By Paul C. Rusanowski

Mining is a waste intensive industry, oftentimes producing hundreds of kilograms of waste rock and tailings for every gram of metal recovered. Disposal of mine tailings is a major concern in most mining operations. In Southeast Alaska the steep terrain and high seismic hazard province limits cost effective opportunities for land disposal of tailings. The lack of infrastructure and long travel distances generally limits secondary utilization of tailings, as well. Since the mines are located close to tidewater, submarine tailings disposal is an attractive option for tailings management. At the present time the EPA will not issue a permit that authorized marine tailings disposal from any mining process that includes flotation technology. Upland disposal is the "Best available technology" and must be used. Consideration of submarine disposal is generally precluded because the tailings are contaminated with fluids from the flotation process. However, when developing technological solutions to minimize environmental disturbance, destruction, pollution, and risk, submarine tailings disposal deserves another evaluation. In Southeast Alaska it may be the "Best available technology" based on an assessment of all issues and concerns in these mining projects.

Jan 1, 1991

By Richard H. T. Garnett

On the western continental shelf of southern Africa diamonds derived from onshore sources are concentrated in gravels within drowned terrestrial and marine geomorphological features. First discovered offshore in the late 1950's, they are known to exist for about 1400 km along the Namibian and South African coast in water depths of up to 200 m. Shallow water operations yielded 1.5 Mct during the decade ending 1970 when De Beers acquired a majority of the offshore leases and commenced a 15 year exploration program. Deeper water and the prevailing sea conditions required the development of new, unique, marine mining equipment. The first large scale mining production of 22 kct was achieved by De Beers in 1989 with an output of 22 kct. Annual marine output from all sources now exceeds 0.6 Mct worth some US.$ 170 M, and rising to 0.7-0.8 Mct for 1998. Exploration has also been taking place in the waters of West Africa, Australia, and Indonesia. Exploration is by means of high resolution geophysics followed by sampling using a variety of drills, airlifts and seabed-mounted machines which imitate the eventual mining process. Surveying is now probing depths of 500 m. Smaller scale mining by several junior companies has traditionally involved diving and airlift systems. Increasingly, however, they are adopting different and improved techniques which to date have been employed only by De Beers Marine as contractor to Namdeb. Marine exploration and unit mining costs are high compared to those applicable to alluvial deposits onshore. By 1996 the total development costs incurred by De Beers alone reportedly had exceeded US.$ 500 M. However, the financial rewards are commen-surate because of the higher recovered grades. The operations are not without risk for the total of nearly 10 large and medium scale production vessels deployed by various organisations. The greatest shortfalls are experienced in the estimated throughput, not the grade.

Jan 1, 1998

By Jan M. Peter

The Early Norian Windy Craggy massive sulfide deposit is within the allochthonous Alexander terrane of the Insular tectonic belt in extreme northwestern British Columbia (Figure 1). Host rocks are the Middle Tats Volcanics, part of an informally-named volcano-sedimentary succession of mixed graphitic argillites and mafic pillowed and massive volcanic flows and sills of Upper Triassic age (Figure 2) that have suffered only lower greeschist-facies metamorphism. The volcanic rocks are light rare earth element (LREE)-enriched and display a variably developed back-arc subduction signature. Major and trace element compositions of the host argillite show that it contains an appreciable hydrothermal component, as evidenced by low high Fe and Mn contents. These sediments therefore record steady, continuous hydrothermal activity punctuated by intermittent turbidity currents sweeping into the basin. The deposit consists of at least two discrete sulfide lenses (the North and South Sulfide Bodies), as shown in Figure 3, a level plan at the elevation of the exploration workings. Published reserves at 0.5% copper cut-off are 297.4 million tonnes grading 1.38% Cu, 0.08% Co, 0.21 g/t Au and 3.9 g/t Ag (as of December 1991). However, the deposit is larger than this and further drilling is required to delineate it completely. Mineralization comprises massive sulfide, stringer/stockwork, and finely bedded to laminated sulfides and exhalites. Stockwork mineralization consists of sulfide-quartz-chlorite veins with attendant chlorite and silica alteration. Mineralization consists predominantly of massive pyrrhotite andlor pyrite with lesser chalcopyrite and magnetite. Figure 4 is an oblique section through the North Sulfide Body, the most northerly sulfide mass shown in Figure 3, which shows the distribution of the pyrite and pynhotite-rich massive mineralization and the stringer zone. The North Sulfide Body contains appreciable sphalerite, whereas the South Sulfide Body contains only trace amounts. Gangue minerals include quartz, chlorite, calcite, siderite, ankerite, stilpnomelane and magnetite. The minor hydrothermal exhalite sediments are comprised of chert, carbonate, and minor

Jan 1, 1993

By William D. Siapno

The International Marine Minerals Society has now come of age! Previously known as the International Marine Mining Society, it was an informal group without officers, by-laws or official status. Despite the lack of formal structure, the Society has cosponsored symposia both in Europe and in North America including the 16th Annual Underwater Mining Institute in Halifax, Nova Scotia, last year. The roster of members is now sufficient to emerge as a fledgling professional society. To this end an ad hoc committee was appointed to prepare by-laws stating the objectives of the Society, provide the procedures for the election of officers and other guidelines essential for the operation of the organization. This paper briefly summarizes the history of the group, the by-laws, together with membership requirements.

Jan 1, 1986

By Maria Baker, Kristina Gjerde, Lisa Levin, Verena Tunnicliffe, Lenaick Menot, Rachel Boschen

Deep-sea mining is rapidly approaching the test-mining phase to prepare for commercial mining in multiple oceans, both in areas within and beyond national jurisdiction. The first test-mining operations are likely to focus on seafloor massive sulfides found at active and inactive hydrothermal vents within national jurisdictions – possibly in the coming months. Beyond national jurisdictions, the International Seabed Authority (ISA) is developing the regulations to oversee exploitation of polymetallic nodules, massive sulfides and cobalt crusts. The Deep Ocean Stewardship Initiative (DOSI) minerals working group has, over the last 3 years, made formal submissions on the regulatory framework, on the draft exploitation regulations, on the article 154 review of ISA and on the initial environmental regulations. In advance of both test and commercial mining, we urgently need to identify and develop comprehensive, ecosystem-based management practices for deep-ocean environments subject to mineral extraction. Transparent criteria for deep-sea institutional and corporate social responsibility also need to be established. Proactive development of management practices, frameworks and policy prior to the onset of mining will facilitate some degree of protection and preservation of the marine environment, whilst enabling the use of seabed mineral resources. The DOSI minerals working group constitutes a broad spectrum of scientific, industry, legal and policy expertise. We provide expert opinion, both in collated and individual response forms, on deep-sea mining related concerns to ISA and national bodies. Our publications and workshops on key concepts raise awareness and provide scientific updates on ecosystems targeted for mining. See http://www.dosiproject. org minerals working group and join us to further this work.

Jan 1, 2017