Search Documents

By Alan J. Lutenegger

A series of tension tests were performed on prototype scale steel pipe piles at two sites to evaluate the influence of scale and pile plugging on the unit skin friction developed in axial tension. The first site consisted of a clean medium dense fine sand above the water table. The second site consisted of a loose silty sand with the water table within about 0.5 m of the ground surface. Pile load tests performed at each of the sites included piles with diameters ranging from 73 mm to 114.3 mm, which may be considered driven "micropiles". At the first site, pile lengths of 6.1 m were used; at the second site, pile lengths of 9.1 m were used. Some of the piles were driven open-ended while others were fitted with a conical tip to form a closed end. During installation, pile plugging measurements were taken on the open-ended piles after each 0.30 m of penetration. The piles were allowed to rest for a period of about 30 days after driving prior to performing the axial uplift load tests to failure. The results indicate that in the medium dense fine sand the unit skin friction developed in tension is dependent on both the amount of plugging that occurs and on the size of the pile, which was not the case for the loose silty sand.

Jan 1, 2000

By Makarand G. Khare

Though the phenomenon of dragload is known for many decades, there is a lack of clear guidelines to evaluate the amount of dragload. The development of dragload depends on relative movement between pile and surrounding soil which is a complex phenomenon and requires a detailed numerical analysis. Bitumen layer has been used in the past with varying degree of success in reducing the dragload but the reduction appears to depend on number of parameters. No procedure is available in literature to estimate the dragload when a slip layer is applied on pile surface. This paper investigates performance of two commercially available bituminous coats to reduce the negative skin friction on pile. Direct shear test apparatus was used to model the interface friction between soil and coated pile surface. The lower half of direct shear box was replaced with either a concrete block or a mild steel block representing pile surface. Two types of bituminous coats namely Shalikote and bitumen having penetration value of 30-40 were evaluated in this study. Shearing resistance of pile material-coat-soil is found to be influenced by normal stress, coat thickness, and rate of shear. Laboratory results are compared with published field data where coated and uncoated piles have been load tested.

Jan 1, 2006

By A. Partos

It was decided to build a fourteen-storied office building over a six-storied garage and a four-storied office building. The high vertical and horizontal loads required foundations on rock approximately 18m below street level. Drilled piers (caissons) were selected. Eight caissons (1.98m diameter) were installed through the six-storied garage and four caissons from a temporary deck at the location of a former two-storied building. Excavations were done by the slurry method. Proof testing of rock was done before construction by test borings and during construction with a core barrel of small diameter. Quality control measures included telecommunications between ground crews and the equipment operator on the garage roof; records of field observations and testing of bentonite slurry and rock; and a continuous evaluation of all information. Instruments were installed in one caisson to monitor load distributions and curing of concrete.

Jan 1, 2010

By John A. Egan, Nathaniel Wagner, Micaela Largent, Jonathan P. Stewart, Debra Murphy, Jeremy Butkovich

The Millennium Tower is a 58-story reinforced concrete building that was constructed in San Francisco, California between 2005 and 2009. The Tower is founded on an embedded pile supported mat with pile tips bearing in dense marine deposits that overlie an over-consolidated marine clay layer known locally as Old Bay Clay. This clay layer experienced stress increases from Tower self-weight and from multiple episodes of de-watering between 2006 and 2018 at the Tower site and neighboring sites. Settlements of the Tower foundation have been measured since 2006 and lateral deflections of the Tower have been inferred and measured since 2009. Available information on this case history include geotechnical site conditions and data from a monitoring program that tracked foundation settlements, Tower tilt, groundwater levels at the Tower site, and ground inclinations over time. This presentation will discuss the ground deformation mechanisms that caused the observed movements, the degree to which the movements can be predicted, and lessons from this case history for the design of deep foundations for tall buildings in San Francisco and geologically similar regions.

Sep 8, 2021

By Jack Hayes

Vibrating wire strain gages have proven to be a very reliable and effective tool for the measurement of strains associated with the loading of bored piles (drilled shafts). However, when these strains are used to calculate the load, or stresses in the pile, the results can sometimes be confusing and/or difficult to interpret. This paper describes some of these situations, using examples from actual case histories, and discusses some of the difficulties associated with residual load effects, curing and temperature induced strains, load stress distribution effects, estimated modulus and area.

Jan 1, 2002

By Z. Q. Bian

The wireline sampling originates from core drilling in rocks. The authors combined the wireline sampling technique with conventional undisturbed soil samplers, including Osterberg sampler, Denison sampler and double tube barrel, and then developed the wireline samplers of WPS, WSS and WSR models. These samplers are able to sample various soils. They reserve all the advantages of the original samplers, and moreover, they are noted with quick hoisting and lowering by wire rope. Therefore, it becomes an efficient new technique of sampling undisturbed soil from deep foundation.

Jan 1, 2010

By Ana Pereira, Naomi Norris, Donald Bruggers

The city of Christchurch, New Zealand is predominantly founded on alluvial sediments consisting of interbedded layers of loose to medium dense sand, soft to stiff silt and clay mixtures, and pockets of organics. These soil deposits have high liquefaction potential. Following the 2010/2011 Canterbury Earthquake Sequence several ground improvement trials were undertaken within Christchurch to understand the effectiveness of different types of ground improvement in these silty sand geological conditions. This paper presents a discussion of a stone column ground improvement trial undertaken at a Christchurch site with high fines content soils. Stone columns were installed using two types of installation methods and a range of Area Replacement Ratios (ARR) to assess the effectiveness of these ground improvement methods in high fines content soils as well as the influence on the type of installation method. Pre- and post-column installation CPTs, seismic Dilatometer Tests (sDMTs), cross-hole shear wave velocity tests, and plate load tests have been undertaken to assess the effectiveness of the ground improvement. Results of the testing are presented in this paper. INTRODUCTION This paper presents the results of a stone column ground improvement trial undertaken in Christchurch, New Zealand (Fig.1). In 2010 and 2011, four large earthquakes (greater than magnitude 5.9) and thousands of smaller aftershocks occurred in the greater Christchurch region. These events are referred to as the Canterbury Earthquake Sequence (CES). Liquefaction occurred across large portions of the city during the stronger earthquakes, particularly the February 2011 event. Following the CES a large amount of data was collected across the city including the location and volume of sand boils, and the location and magnitude of ground cracks. Additionally, data from thousands of ground investigations have been uploaded into a public database. As a result, there is clear evidence that silt and silty sands liquefy in addition clean sands. The CES and resulting liquefaction motivated a series of studies and trials from different organisations aiming to better understand the available technologies for liquefaction mitigation. The subject of this paper is a ground improvement trial undertaken by a local contractor specialising in deep foundations and ground improvement. They were interested in understanding the effectiveness of stone column ground improvement in high fines content (silty) soils using two different installation techniques, vibratory and non-vibratory. Different arrays and Area Replacement Ratios (ARRs) were used for each of the two methods of columns installation.

Jan 1, 2019

By Andrew Budek

Reinforced concrete piles are used to carry foundation loads through considerable depths of soil to provide superstructure stability under gravity loads and lateral forces. The creation of cast-in-place (or cast-in-drilled-hole, i.e., CIDH) piles begins with the auger-drilling of a hole of the appropriate depth, into which a cage of reinforcing steel is placed (the cage length is generally equal to the depth of the hole, a construction joint being used to connect the in-ground pile with the superstructure). The pile is then finished by casting with concrete, and the superstructure then appended. The superstructure may either be a column (denoting the structure a pile-column), a column and cap beam, or a footing. Typical pile-column configurations are shown in Fig. 1 (a CIDH pile used in a footing would be similar in overall configuration to Fig. 1(b), with H=0). CIDH piles are well-suited for alluvial soil profiles with a deep water table; such conditions generally allow the auguring of a clean and regular hole.

Jan 1, 2007

By Arash Khosravifar

One of our research thrusts at Portland State University (PSU) centers on developing design guidelines for pile foundations in liquefiable, laterally spreading grounds. This research has been primarily sponsored by the DFI Committee Project Fund (CPF) program through four awards, totaling nearly $240,000 in financial support. DFI contributed half of this financial support, while the other half was contributed in-kind by PSU and DFI Project Advisory Board members. Leveraging the CPF funds, we secured an additional $550,000 in financial support from the National Science. Foundation (NSF), which has enabled our research group to continue exploring this topic and contributing to the broader engineering community's understanding of the behavior of pile foundations in liquefiable soils. The CPF funds have fostered collaborations with practitioners and researchers beyond PSU. Notable examples include collaborative research involving data from five large-scale centrifuge tests on pile-supported wharves by Steve Dickenson, Ph.D., New Albion Geotechnical; Nason McCullough, Ph.D., Jacobs Engineering and Scott Schlechter, Geotechnical Resources, as well as 1-g shake table tests of bridge pile shafts conducted by Professors Ahmed Elgamal, Ph.D., and Ahmed Ebeido, Ph.D., of the University of California, San Diego. In addition to these collaborations, our research has benefited from industry-university partnerships formed through the involvement of DFI Project Advisory Board members. Their support and feedback ensure that our research products are practical and imple- mentable in real-world projects. The impact of the CPF funds extends to supporting graduate students' theses, which were the basis for 17 technical publications. Some of these publications are expected to have a significant impact on the industry. For instance, our 2018 DFI Journal paper, co-authored by former master's student Jonathan Nasr, cur- rently with the Army Corps of Engineers, has been cited in the 2022 British Columbia Supplement to Canadian Highway Bridge Design Code S6:19. A noteworthy product of our study is a step-by-step design procedure for pile- supported wharf structures subjected to the combined effects of lateral spreading and inertial loads, outlined in a 2022 American Society of Civil Engineers' (ASCE) Journal of Geotechnical and Geo- environmental Engineering paper co- authored by former doctoral student Milad Souri, Ph.D., PE, Geotechnical Resources.

Nov 1, 2023

By C. N. Baker

The design and construction of drilled piers through water bearing and caving soil conditions are discussed. The need for close cooperation between the design engineer and contractor in both the design and construction stage is outlined. Four case histories illustrating the design and construction considerations for four different problem soil and ground water profiles are presented, including the field testing and observation procedures that were utilized to confirm that the design inten. was accomplished. Requirements advisable when placing concrete under water in a cased environment and when placing concrete under slurry in an uncased environment are described.

Jan 1, 2010

By Jesus Gomez, Mary Nodine

Rigid inclusions are widely used in the U.S. as a ground improvement tech- nique, particularly for industrial, low- rise and highway applications with poor subsurface conditions, where control of settlement is necessary. Rigid inclu- sions consist of grouted or concrete elements typically 12-24 in (305-610 mm) in diameter that may or may not be reinforced with a center bar. Typical soil conditions where rigid inclusions are feasible might consist of a surface layer of fill and natural, granular soil, followed by a stratum of soft silt or clay overlying a dense or stiff formation. Rigid inclusions are installed from the existing ground surface or suitable work platform, through the surface soils and through the soft, compressible layer, and into the deeper layer, which is less susceptible to compression- induced settlement. Typically, when used to support an extended area surcharge, the inclusions are installed in a rectangular or triangular pattern at regular spacings ranging from 5-12 ft (1.54 m), depending on a variety of factors. The rigid inclusion system is often capped with a load transfer platform (LTP), whose function is to direct a significant portion of the applied load toward the rigid inclu- sions. Additional load is transferred to the rigid inclusions through the upper fill soils above the compressible layer. The rigid inclusions transfer the applied load axially to their tips and into the deeper layer. In the U.S., rigid inclusions are mostly installed using displacement auger systems. The use of a dis- placement auger has significant advantages. It produces zero to near- zero spoils, which is an important environmental consideration. The

May 1, 2023

By R. K. M. Bhandari

Geotechnical investigation for a LPG plant located in Assam state - an area of high seisimicty - revealed a layer of loose to medium silty sand susceptible to liquefaction at some depth below the finished ground surface. Liquefaction analyses were carried out using simplified Seed's approach as well as considering the progressive buildup of pore pressures with cyclic earthquake loading. Seismic settlements were computed for areas where the analysis indicated partial liquefaction. Pile foundations in areas where complete liquefaction was indicated, were treated with gravel drains to prevent buildup of pore pressures. The paper presents and discusses the liquefaction analyses, effect of non-liquefiable overburden soil on the liquefaction potential of the silty sand and the remedial measures that have been taken to ensure safety of the pile foundations in transmitting vertical and lateral loads.

Jan 1, 1996

By V. T. Ganpule

The effect of Sulphate and Chloride is well understood by the engineers. Most of the codes stipulate permissible limits for sulphate and chloride content in groundwater. Relatively few reference are available about the effect of organic acids on pile concrete. While executing a pile foundation work around Bombay, the authors came across the peculiar phenomenon. The routine testing of water has indicated that water is non-aggressive; however, on exposing the piles, the piles were found to be highly detonated. The testing of water on the guidelines followed by engineers associated with flow through pipes revealed that water is corrosive as per the Ryznar index concept. The present papers discussess the significance of Ryznar index in under water concreting.

Jan 1, 1996

By D. J. Ketkar

It is a frequent experience to find that the Sub-surface Investigation (S.I.) data is either inadequate or misleading. However, such cases are rarely reported. Nonetheless, the projects suffer on-account of delays, cost-over-runs, disputes and/or compromise of the safety norms. Many times S.I. is considered unnecessary or is carried out as a ritual, mainly due to (i) non-availability of good S.I. agencies, or (ii) absence of Geotechnical consultant, or (iii) shortage of time. Importance of S.I. cannot be over emphasised. Yet the profession is in a state of confusion - mainly because of lack of competent professional agencies and of well-defined roles/responsibilities of the concerned parties. In this paper, some suggestions are made to get better returns from the S.I. activity.

Jan 1, 1996

By R. L. Wei

The disturbing influences of pile driving on the surrounding soil mass, including the induced vibration, pore pressure and displacement of soil, were observed during the construction of pile foundations. It is shown that the effects of pile driving in saturated soft clay are tremendous and ought to be concerned attentively.

Jan 1, 2010

By Y. W. Mou

In order to improve the construction of pile foundations and deep foundations of largo sizes, the paper deals with the method of installing square or rectangular bored-piles for annular foundation as well as large-sized hollow or solid foundation.

Jan 1, 2010

By Cem Akgüner

The displacements of axially loaded single piles are analyzed with an approach based on elasticity. Young?s modulus and Poisson?s ratio of the soil encompassing a pile are the unknowns required as input to obtain predictions based on the elastic method. Attention is directed towards Young?s modulus because the range and variability of Poisson?s ratio is not significant in displacement calculations. A database of axial pile load tests established for the California Department of Transportation (Caltrans) is investigated. All of the tested piles were driven into the ground. Measurements of displacements and loads were made only at the top of the pile. First the magnitude of displacements is determined up to loads that are half of the failure load measured from pile load tests. Various correlations for Young?s modulus are then employed to determine how accurately each predicts the actual measured displacement. The chosen correlations utilize the routinely available parameters of laboratory triaxial undrained shear strength for cohesive soils and standard penetration test blowcount for cohesionless soils.

Jan 1, 2008

By Joel Moskowitz, George J. Tamaro

"A new office complex is being constructed within 25m of the Hudson River in New Jersey. The project, about 140m by 100m, will include 4 basements under the entire footprint. The perimeter was to be secured by a 0.8m thick diaphragm wall, laterally supported by high capacity tieback anchors to rock. Columns were to be supported on footings or piers to rock at a nominal bearing pressure of 3.8MPa at depths up to 17m. Although some variation in rock quality was observed in borings, a substantial vertical seam of weathered and/or decomposed rock, 1 to 2 meters wide by as much as 8 meters deep, was encountered during construction necessitating field redesign. In some locations, the seam dipped below rock that is more competent. Footings were redesigned for support on drilled caissons, or soft rock was excavated and replaced with concrete necessitating a reduction in bearing pressure of the footings by one half. The tower covering the south half of the site was topped out in 2002 and the garage levels in the north half of the site were completed in 2003.PROJECT DESCRIPTIONIn September 1999, a major investment company began the due diligence process to evaluate a property on the shore of the Hudson River in Jersey City, New Jersey for a new multi-use complex. The site offers a spectacular view of lower Manhattan directly across the river from the site of the former World Trade Center. The site, covering two city blocks, was previously occupied by manufacturing and office facilities of Colgate-Palmolive.The building footprint is approximately 140m by 100m, the southern half of which is occupied by a 260m tall office tower, shown in Fig. 1. As of this writing, design of the structure for the northern half of the site has not been finalized, but it is expected to comprise an 11-story office building. A glass-covered atrium will occupy the street that formerly separated the two blocks. As part of the due diligence process and preliminary design evaluation, alternatives were considered to accommodate various numbers of parking places, both above and below existing grade. A major consideration for below grade parking is the proximity of the Hudson River some 25m east of the east building line."

Jan 1, 2004

By James P. Hambleton, Anastasia Nally

This work focuses on the numerical simulation of multi-plate anchor systems (e.g., helical anchors) in sand subjected to vertical loading. In assessing the stiffness and capacity of these multi-plate anchor systems, full awareness of the abilities and limitations of the various analysis methods must be understood. This work first summarizes studies completed by others and then goes on to assess the failure mechanisms of multi-plate anchors in sand and the influence of (1) plate width-to-depth ratio, (2) number of plates, and (3) relative positioning of plates. The analysis makes use of (1) conventional limit analysis, (2) so-called modified limit analysis that employs reduced strength parameters to account for the influence of soil dilatancy, and (3) the displacement-based finite element method, which considers elastic as well as plastic deformation leading to failure. The work critically reflects on limitations in the current analysis methods for helical ground anchors. INTRODUCTION Helical anchors are a relatively low cost foundation type, typically consisting of a steel rod and single or multiple plate attachments. In recent decades, they have seen rapid growth, and as outlined by Merifield and Sloan (2006) and Hambleton et al. (2014). Design techniques for helical anchors have previously been predominately empirical, as much of the past research in this field is experimentally based. It is common practice for helical anchors to be modeled as horizontally oriented plate anchors in both numerical and experimental analysis. This work focuses on analysis based on the finite element method, including so-called finite element limit analysis and the conventional displacement-based finite element method, with some comparisons made to experimental studies. Numerical simulation of anchor pull-out capacity in cohesionless soils is stunted by the many difficulties faced when using numerical analysis with cohesionless soils. Additional variations can be seen when comparing the serviceability based load capacities to the ultimate load. In this work, both the force-displacement response (stiffness) and the ultimate anchor capacity are assessed, with more focus on the latter. This work focuses only on analysis techniques for multi-plate anchors with vertical loading in cohesionless soils. Many studies have been completed in this area, some of which assume a rectangular plate in a plain strain model (Rowe & Davis, 1982; Merifield & Sloan, 2006; Cerfontaine et al., 2019). Whereas others use axisymmetric conditions (Baker and Kondner, 1966; Saeedy, 1987; Murray & Geddes, 1987; Ghaly & Hanna, 1994; Sakai & Tanaka, 1998; Merifield et al., 2006;) and minimal studies considered both axisymmetric and plane strain in the one study (Vesic, 1971; Tagaya et al., 1988; Murray & Geddes, 1987; Sarac, 1989).

Jan 1, 2019

By Chris M. Haberfield

The design of side resistance of drilled shafts socketed into rock has traditionally been empirically based on the results of pile loading tests in which the side resistance can be isolated from the side resistance. In practice, this is achieved in one of several ways : loading the pile in tension, using a collapsible base, or by using a device such as an Osterberg cell to load the pile from the base. Although this approach has resulted in generally safe design practice, this has been at the expense of efficient design practice. Safety in design has been achieved through conservatism, which has been necessary because of the large scatter that is evident in the pile socket resistance database (Rowe and Armitage, 1984; Kulhawy and Phoon, 1993). Research at Monash University through the 1980's has been aimed towards understanding and then modelling the complex mechanisms of shear transfer at the concrete-socket interface of sedimentary rocks. Armed with such an understanding, the important factors which affect the strength of pile sockets can be isolated, and the reasons for the large scatter can be deduced. This paper briefly describes the research approach taken, and the main features of the design method and computer program which have now been developed. Some load-settlement predictions of the program are compared with the results of full-scale pile socket tests. The paper then presents the results of a numerical study which relates predicted socket a factors to unconfined compressive strength of the rock, socket diameter, initial normal stress and socket roughness.

Jan 1, 1996