Search Documents

By R. G. Zaripova, N. D. Ryan, H. J. McQueen

The austenitic and ferritic stainless steels do not undergo any phase transformation that induces very fine grains in the product through thermomechanical processing as practiced in most other steels. Considerable grain refinement can be achieved by intense multistage deformation descending through warm to cold working; notably multi-axial forging of bulk material can attain high strains with diminished risk of cracking. Hot working to improve ductility yields finer grain sizes as the T is reduced and strain rate E raised; increased strain has limited effect due to the steady state regime. Ferritic steels develop subgrains with size diminishing as E rises and T falls with the advantage of retained strain hardening; recrystallization delivers grains several times the cell size. In austenitic steels, dynamic recrystallization (DRX) provides finer grains at higher E and lower T with a lower limit due to intergranular cracking. The DRX grains contain a strengthening substructure that can easily be retained by quenching; if static recrystallization is allowed to occur the grain size rises markedly. Multistage rolling with diminishing T is able to provide grain refinement to the same degree as straining at the finishing T yet provides better ductility. grains on recrystallization. As a result of the strain induced transformation to martensite, small subzero deformations of austenitic or duplex steels produce very high dislocation densities that yield marked grain refinement when they revert upon reheating.

Jan 1, 2004

By E. V. Konopleva, H. J. McQueen, V. M. Khlestov

In addition to increasing grain boundary area during hot working of austenite, the dislocation substructures create potential sites for nucleation of ferrite both at original grain boundaries and at transition boundaries between deformation bands. This development gives rise to a marked increase in the rates of nucleation, of growth and of transformation to ferrite. The combined net effect is product grain refinement that requires less stringent cooling between finish rolling and coiling; hence determination of the above rates would advance process optimization. The important control parameters are the preheat temperature (degree of homogenization), finishing temperature, strain (accumulation near finishing) and the extent of recrystallization after finishing. These effects vary greatly with steel composition; nevertheless, some general rules have been formulated. Moreover, there is also potential for deformation of the refined ferrite. There are other thermo-mechanical processes such as warm forming of metastable alloy austenite to provide a dense substructure that is carried into the martensite on quenching. In other processes, the austenite may be deformed during cooling through the transformation to develop a dense substructure in the ferrite that is stabilized by fine carbides.

Jan 1, 2004

By R. A. McIvor, R. Levac

"The Stobie No. 7 shaft, 14 ft diameter, double- drum skip hoist, was installed at the INCO Limited Frood Stobie Complex in 1942. Figure 1 shows the hoist layout. The hoist was originally equipped with babbitted journal bearings on the main drum shaft and pinion gears. In 1990, the hoist was modernized with a new braking system, two new 2000 hp D.C. drive motors, a thyristor armature supply and a PLC control system. The new drive motors were connected to the drive pinion gears with a gear type flexible coupling. The pinion gear journal bearings were refitted during the refit in 1990 as the existing babbitted bearings showed signs of wear. The pinion gear journal bearings had always run warm and had external cooling applied during the warm summer months. Figure 2 shows the journal bearings on the pinion shaft. The skip hoist main bull gear and two pinion gears were replaced in 1997 because of cracked bull gear spokes. New drive couplings were installed on the pinion gears and the pinion journal bearings were modified to allow some self-aligning properties to try to reduce the heating and wear on the babbitt. The modifications did not significantly reduce the heating problems and a decision was made in the spring of 1998 to convert the bearings to self-aligning, anti-friction-type bearings.The traditional roller bearings used on double helical pinion drive gears in hoist applications has always been double-row spherical roller bearings due to their high load-carrying capacity and misalignment allowances.Unlike single helical gears, double helical arrangements do not exert axial thrust on the pinion gear bearings, therefore, both bearings in the pillow blocks must float easily with any pinion displacement. Drum misalignment, thrust bearing end play and a multitude of other influences causes continuous axial displacement of the pinions when in operation. This constant displacement or “hunting” of the pinion gear to maintain its centre on bull gear often exceeds the axial clearance limits of spherical roller bearings thus resulting in a continuous sliding motion of the bearing outer rings against the housing seats. With time, the housing fit eventually wears, creating an out-of-round condition for bearing housing (maximum allowable cylindricity tolerance is IT4/2). When this happens, the pillow block housings must be replaced or re-machined to specification. Premature bearing wear and overheating will occur if a housing out-of-round condition is encountered."

Jan 1, 2001

By Horst Konig

This paper illustrates that, with the application of new processes, smaller steel plants using local raw materials can be economical and advisable. It also introduces the problems connected with the direct reduction processes, which use non-coking coal or gas as reducing agents, and which are employed in connection with conventional reduction to produce excellent results. Electric smelting is also discussed, and some practical examples of operating plants are given.

Jan 1, 1970

By L. D. Smith

Net Present Value Impact of Discount Rate The Discounted Cash Flow (DCF) method of valuations is universally used and accepted. The main criticism of the method is that it does not recognize the value of projects long life projects. This can be seen in the preceding graph where the present value of cash flows in later years are small for discount rates over about 10%. This graph covers a project that has a 25 year operating life. It is clear from the low height of the NPV bars at 10% and 15% in the last years of the project that an additional 25 years would add almost no value to total project NPV. As an example of this effect, an colleague undertook the evaluation of a pulp and paper project. The plant could be justified, but it was not possible to justify planting the trees as they took too long to grow and so had not appreciable NPV. The plant had to purchase wood to feed the plant.

May 1, 2013

By Stephen G. Downs

PCF?, or Penetrating Cone Fracture, is a propellant-based technique for rock excavation, which has significant potential for the mechanization of narrow-vein mining. The technique is currently being developed for use in the narrow-vein flat-dipping gold and platinum deposits in South Africa in conjunction with major mining companies. The technique is also applicable to steeply dipping vein deposits, such as those found in North America, Australia and elsewhere. The implementation of PCF? in South Africa to date is reviewed and plans for the introduction of PCF? excavation in other areas are highlighted.

Oct 1, 2001

By E. LaRocque

"Long term contracts requiring delivery of 6,000,000 pounds of U308 per year to its customers have made it necessary for Denison Mines to expand its milling capacity from 7,100 tons per day to 15,000 tons per day.Previous papers (1) and (2) described the old leaching and product recovery practice. The flowsheet briefly includes a crushing and grinding circuit, sulphuric acid leaching in a Pachuca plant, liquid-solid separation with wash thickeners and two-stage drum filtration, concentration and purification by moving bed ion exchange followed by two-stage precipitation to produce an ammonia yellowcake.No. 1 Shaft ore, about 4,000 tons per day, will be processed through the truck dump into the old crushing and grinding plant and through the old leaching plant. Ore from Stanrock (No. 3 shaft) will be hauled by truck and also processed through the truck dump as No. 1 shaft ore. Beginning in 1982, ore production from Stanrock will gradually increase until 1985 when some 3,000 tons per day will be milled from the source.A new 8,000 ton per day circuit was designed and constructed to increase the milling capacity to 15,000 tons per day. The new circuit is separate from the old one except that it coins together for the precipitation and tailings neutralization sections of the plant. The feed to the new plant will be from No. 2 shaft.The flowsheet is much the same as the old plant with the exception of the grinding circuit and the ion exchange plant. A semi-autogenous grinding (SAG) plant, unique in the Elliot Lake area, has been installed rather than the conventional crushing and grinding plant; the ion exchange plant is the stationery bed type.This paper describes the major equipment installed for the expanded grinding and hydrometallurgical plant."

Jan 1, 1982

By Shahé Shnorhokian

Remnant pillars evolve towards the latter stages of mining in an orebody and act as repositories of mining-induced stress. It is therefore crucial to plan ahead as to their dimensions and location with respect to the local geology. A case study of a Canadian base metal mine was examined for the planned mining sequence scenario to identify the stress regimes acting on a future remnant pillar occurring between levels 4800 and 5100, near a brittle dyke. A mine-wide model was constructed in FLAC3D and input parameters included results from field measurements of the direction and magnitude of the principal stresses, and the geomechanical properties of the different formations. Prior to the study, the model was calibrated based on a 6-year record of mining-induced seismicity and rockburst events, focusing on large event clusters. The mining sequence followed at the mine was then used in the model to study the planned future extraction program around the remnant pillar. It is shown that the distance of the remnant pillar from the dyke and another orebody plays an influential role on the stress levels developed in the pillar.

Jun 1, 2012

By George Rice

Foreword Following the explosion in the Hillcrest mine, which occurred in the evening of Sunday, September 19th, 1926, and in which two men lost their lives, the writer was invited by the Hon. J.E. Brownlee, Premier of Alberta, to conduct an investigation into the causes of the disaster, and to make such recommendations as seemed advisable with a view to minimizing as far as possible the chance of future explosions in this and similar Alberta coal mines. Accordingly, the mine was visited, and extensive investigations were made underground on October 21st, 2.2.nd, and 25th, in company with Mr. John T. Stirling, Chief Inspector of Mines for Alberta, Mr. Moses Johnson, District Inspector for the Crowsnest Pass District, Mr. J as. A. Richards, Inspector of Mines, Edmonton, and also Mr. Thomas Davies, manager, and other officials of the Hillcrest mine. Hearings of the coroner's inquest were also attended on October 20th and 23rd, when testimony regarding the explosion was given by various witnesses. The following paper summarizes my general observations in tracing the place of origin of the explosion, and my efforts to determine the cause of ignition. Certain recommendations arc also made, and the writer invites discussion on these and the other matters dealt with in the paper.

Jan 1, 1928

By J. E. Hawley, Y. Rimsaite, T. V. Lord

"IntroductionIN THE COURSE of. a spectrographic investigation of the platinum metal .content of various minerals in sulphide ores, the use of • fire-assay beads dissolved in gold-amalgam ( 1) was found suitable for the quantitative determination of palladium and platinum. Later work on platinum and bismuth-rich beads showed however, that these could not always be readily mixed uniformly in the amalgam. Accordingly another technique was sought which would allow the simultaneous determination of gold, silver, palladium, platinum, rhodium, and bismuth, the last .a common contaminant in fire-assay beads. The method evolved, which consists of dissolving fire-assay •beads in .lead, resembles in several respects the method of Scobie (2) in which silver was used. It has equally good sensitivity arid reproducibility, and allows the determination of silver as well as the other metals mentioned. The 'mutua1 standard' method of calculation (3a) is used to determine actual quantities present. This method has been applied to sulphide and arsenide minerals and •ores• of nickeliferous and non-nickelferous deposits• of both pre-and post Cambrian age, and, following a suggestion by Dr. G. S. Hume and the late Dr. H. V. Ellsworth, Geological Survey of Canada, has also been used for a peculiarly rich platiniferous uranium oxide ore from the Nicholson property, Lake Athakaska, Sask. More recently, the method has been .tested for the determination also of iridium and ruthenium and results indicate it may be applied, as• well to osmium."

Jan 1, 1953

By L. W. Vollmer

Introduction During the past three years at least fifty strings of 9% nickel steel tubing have exhibited excellent resistance .to the variably severe corrosive conditions typical of many of the sweet condensate wells in Mississippi, Louisiana, and Texas. This experience, and the characteristically outstanding performance of other ?nickel alloy steels under hydrogen sulphide corrosive conditions, dictated the selection of 9% nickel steel tubing for the second well drilled in the sour condensate Pincher Creek field of southwestern Alberta. The damaging effects of the Pincher Creek reservoir fluids on well equipment had been manifested in the discovery well by the rapid and not yet fully understood failure of API Grade N-80 tubing, stainless steel wire lines, and alloy steel fishing tools. Two very unexpected failures in the 9% nickel steel tubing, after only six days of service in production tests, instigated an extensive and continuing investigation to ascertain the probable cause of failure. This discussion presents some of the results obtained thus far which cast a little light on the perplexing behaviour of steels in hydrogen sulphide environments in general, and in sour condensate wells in particular. History of Tubing Failures Walter Marr well No. 1, in which the 9% nickel steel tubing failures occurred, produces from the Madison lime at the depth interval approximately 12,200 to 12,750 feet. The gas-oil ratio is about 26,000 and the gas contains 10.2 per cent hydrogen sulphide and 6.3 per cent carbon dioxide by volume.

Jan 1, 1952

By K. Schimann, H. D. Knipping, J. P. Fouques

"RESUMELe gisement d 'uranium de Cigar Lake, dans la région de l'Athabasca au nord du Saskatchewan, fut découvert en mai 1981 par Cogema Canada Ltée, opérant pour Ie compte de la ""Waterbury Lake Joint Venture"".Le corps minéralisé. qui est dépourvu de toute expression directe en surface, est situé a la discordance entre les met sédiments du wottaston Group (Protérozoïque inférieur ou Aphébien) et les grès de l 'Athabasca (Protérozoïque moyen ou Hélikien), à une profondeur de 410 a450 m.Fin 1984, Ie gisement était reconnu par 105 sondages minéralisés repartis sur une longueur de 1800 m, pour une largeur comprise entre 25 et 105 m. 11 se présente sous forme d’une lentille aplatie de 5 a30 m de puissance, et montre une remarquable continuité d'ensemble. Une ride ou bombement topographique de la discordance est associée au gisement surtoute sa longueur.A l'échelle régionale, le corps minéralisé à est associe à un corridor structural d’orientation est-ouest, a l'intérieur duquel des facies particuliers aténdance blast mylonitique sont développes dans les formations métapolitiques agraphite du socle métamorphique. Il est entouré par un halo d'altération très important, caractériser Ie développement de minéraux argileux alumino-magnesiens (illite-chlorite).La minéralisation est située, pour la plus grande part, dans les grès d'Athabasca, et se compose essentiellement d'uraninite et de sulfo-arseniures de nickel et de cobalt,De nombreux levés géochimiques et géophysiques ont été effectues dans la région de Cigar Lake. Aucune anomalie ne peut être associée directement au corps minéralise, mais la combinaison des données en provenance de plusieurs sources s’est révélée fort utile au niveau de l’interprétation géologique régionale et de la définition des cibles de sondages a l'intérieur des zones reconnues favorables.Le gisement de Cigar Lake présente de nombreuses analogies avec plusieurs des gites classiques de la région de l'Athabasca; il est caractérise en particulier par l'intensité des phénomènes d’altération et la présence de minéralisations extrêmementriches.En 1984, les réserves géologiques globales estimées par géostatistique sur I ‘amas minéralise principal s 'élevaient a 110 000 tonnes d'uranium, aune teneur moyenne de 12.2%, avec une précision de 25% à l'intervalle de confiance de 95%.ABSTRACTThe Cigar Lake uranium deposit, in the Athabasca area of North Saskatchewan, was discovered in May 1981 by Cogema Canada LId., as operator of the Waterbury Lake Joint Venture. The deposit, which is devoid of direct surface expression, is located at the unconformity between the Lower Proterozoic (Aphebian) Wollaston Group meta-sediments and the Middle Proterozoic (Helikian) Athabasca sands tone, at a depth of 410 m to 450 m below surf ace.AI the end of 1984, the deposit had been defined by 105 mineralized holes over a length of 1800 m and a width of between 25 m and 105 m. It has the shape of a flat-lying lens 5 m to 30 m thick and shows a remarkable longitudinal and latera continuity from the information obtained to date. A well-defined bulge of the unconformity underlies the mineralized zone over its entire length.The deposit appears to be controlled by an east-west-trending structure within which a particular rock facies (""augen gneiss"") has developed in the graphitic metapelites of the Wollaston Group. It is surrounded by a strong alteration halo affecting both sandstone and basement, characterized by extensive development of Mg-A I rich clay minerals (illite-chlorite).The mineralization is hosted principally by the Athabasca sandstone, and consists mainly of uraninite and sulfo-arsenides of nickel and cobalt.Numerous geochemical and geophysical surveys have been carried out in the Cigar Lake area, and no specific geochemical or geophysical anomaly can be directly associated with the mineralized body, although there may be locally a good coincidence. However, a combination of several methods proved extre"

Jan 1, 1986

By V. Aprahamian, T. Cheng, M. Tangen, R. Beauprie

The Royal Canadian Mint has implemented significant process additions since 2005. Installation of a whole new highly automated silver refining circuit has allowed recovery of physical silver from gold and silver dorés . To complement this change, a small Top Blown Rotary Converter has been in operation. On the gold refining side, a new hydrometallurgical process to recover precious metals from Miller Chlorination slag has been developed. Finally, new systems have been put in place to improve treatment of waste water, wet and dry fume and dust.

Jan 1, 2011

By F. Hassani

This Paper describes a sudden spill of rock waste used for backfilling from a waste pass at one of the underground mine in Canada thus causing a major failure/accident. The mine operator immediately launched a detailed investigation to understand the causes of this accident and develop procedures to prevent any recurrence of such events in future. The investigators from McGill University were invited to collaborate with the engineers at the mine to examine this accident. The events leading to the accident were studied and appropriate measurements were taken and samples of the waste material was collected for further test and analysis. The field visit and the interview of the witnesses allowed a detail documentation of the events. The sequences of events related to the incident together with the experimental results obtained in the course of the investigation is detailed. The waste material was characterised in the laboratory with regard to its behaviour in the presence of water. This information is then discussed and the failure mechanism involved in this accident is identified. The full recommendation as well as the immediate operational measures implemented by the mine to prevent future occurrence of such events are discussed and presented.

May 1, 2003

By A. G. Roach

HISTORY AND LOCATION SEAL HARBOR GOLD MINES, LIMITED, was incorporated in January, 1934, to take over 116 acres of mining lands in the Stormont gold district, Guysboro county, Nova Scotia. The nearby ten-stamp Mulgrave mill was also purchased, and since that time 974 acres of adjoining properties have been secured from the Government by direct lease. The property is served by a motor road and is about two miles from the village of Goldboro, situated on the shore of Isaac's harbour. The bulk of ?the supplies are brought in by coastal steamer from Halifax, a distance of about 100 miles, since the nearest railway connections are at Antigonish, some 40 miles distant. EARLYY WORK The Seal Harbor properties include the old Partington and Beaver Hat mines. A small tonnage of ore was mined from each and treated on the properties in stamp mills, which were later torn. down . A survey of old records shows that this ore averaged about $8.00 gold per ton. Development work by the present Company was confined to the 100-foot level until February, 1935, but after that rime the incline shaft was deepened to 425 feet and the 300-foot level was explored east and west of the shaft. Six belts of ore were intersected to the west of the shaft. The ore from these belts was hand sorted and the ore portion was put through the 10-stamp Mulgrave mill to defray operating expenses and to serve as a sample of the deposits. The average recovery per ton from this sorted ore was $6.10. Samples of the ore were sent to the testing laboratories of the Mines Branch, at Ottawa, and of Canadian Industries, Limited, at Toronto. Recommendations from both of these authorities were for removal of the coarse gold by concentration and barrel amalgamation, followed by cyanidation of the residue.

Jan 1, 1937

By R. C. A. Thurston

INTRODUCTION THE deleterious effect of stress raisers or notches on the resistance to fatigue of machine components, and other parts subjected to repeated dynamic loading, has been well known for many years. Most engineers in the mechanical field have, at one time or another, encountered a shaft which fractured due to a poor transition fillet, a holding-down bolt which failed due to insufficient tightening or inferior thread form, or a fitted member which broke through a combination of fretting corrosion and clamping stresses. All of these are examples of the damaging influence exerted by stress raisers in fatigue. Other common forms of stress raiser which have taken their toll of dynamic components are: keyways, oil holes, splines, quenching oil grinding cracks, tool marks, and sharp changes in section; some are the result of the design, others of poor execution of the design. It is our experience in the Mines Branch1 and I feel sure this will be corroborated by other fatigue investigators, that the majority of failures are due to incorrect design or faulty preparation of the part concerned, rather than to the use of inferior material. Quite frequently, it is true that the operating conditions necessitate the presence of a 'notch', but even in such cases methods are generally available by which its adverse effect on the life of the component can be reduced or annulled. The purpose of this paper is to discuss a few typical stress raisers, and to provide information on various processes for mitigating their effects in fatigue.

Jan 1, 1951

By Julie Dénommé

Today few in business would argue with the idea that we are living in a world that is Volatile, Uncertain, Complex, and Ambiguous. Coined VUCA by the US Army War College, these four words define the ?turbulence? and ?continuous white water? that the business literature has been documenting for the last decade. This VUCA world became even more relevant to business in 2007 when the Institute for the Future fellow Bob Johansen published the idea of transforming VUCA into Vision, Understanding, Clarity, and Agility. We call this VUCA Prime (VUCA'), and place an infinity loop (8) between them to show their dynamic interaction. This paper presents an exploration of the impact of VUCA 8 VUCA' on business and the conditions under which these dynamic forces help to successfully navigate change.

Oct 1, 2010

By J H. Dressel, J. E. Williams

This paper presents a brief review of what coal gasification is, procedures that are available today and processes that may be available in the future. Examples are given as to how the process might be used in power plant applications, the effect on pollution level and power costs, and some thoughts on the added burden that might be placed on mining and coal preparation.

Jan 1, 1973

By P. Z. Caverhill

In this section of the province only the most meagre of surveys have been made and because these are not sufficient to determine with any degree of accuracy even the total forest area, the information presented in this paper is not complete. Area: -The area south of the Canadian National, and served by the Pacific Great Eastern, is roughly 38,000. square miles, 30,000 of which is classed as productive. This is approximately equal to the productive area of Norway, or half of Finland-or of 30 per cent of Sweden. It is larger than that of either Nova Scotia or New Brunswick. Eliminating from the productive area 3600 square miles of grass-land and areas capable of agricultural development, 26,000 square miles (16,600,000 acres) remains as absolute forest-land, as compared with the 55,000,000 acres of Sweden, the 37,500,000 acres of Finland, the 17,000,000 acres of Norway, and the 7,600,000 acres of Austria.

Jan 1, 1925

By J. W. Merkley, K. B. Hustwick

"The authors describe the use of a computer system for the control oj warehouse inventory at Cominco's Canadian operations. The challenge presented by the company's diverse products and various locations necessitated a practical approach to operational and manpower requirements. The utilization of modern forecasting techniques, manual intervention and exception reporting provides system flexibility. The system also provides both operational and management control to set required service goals at the lowest inventory levels for inventory management.IntroductionCominco Ltd. is a Canadian company, with international operations, the principal business of which is zinc, lead and chemical fertilizer s. Its involvement is fully integrated and range s from mineral exploration through mining, smelting, refining and by-product production to international marketing. It also embraces related services, including trade, wharfarge and power. With head office in Vancouver, it is involved, directly or through subsidiary or associated companies, in Canada and in the United States, Greenland, Europe, Australia, India and Japan.Cominco has over 12,000 employees and 26,000 shareholders, with 91% of all shares held in Canada.Cominco's Inventory Control System is one of the most extensively used computer systems employed by the company. Also, inventory control is regarded as one of the most economically successful computer applications to be undertaken by the Data Processing Services (D.P.S) Group that was responsible for the development of the Inventory Control System.The main use of automatic inventory control has been at operating plants in Western Canada and the Northwest Territories, which are separated by large distances. Each location has equipment-intensive mining and processing operations and it is essential to maintain control of parts and supplies inventories. Some of these locations are remote from urban and industrial centres and it is important to avoid the adverse effects of high personnel costs and re-training due to turnover."

Jan 1, 1982