Search Documents

By F. Flynn, P. Downey, G. Ritson

"Bell Creek Mill which has been in continuous operation since 1987 has undergone numerous operational changes in the past three years. The addition of over 2. 5 million tons of resource at over 13 git from Hoyle Pond Mine precipitated an expansion program for the Bell Creek Mill. This paper discusses the major changes that have occurred over the past two years to increase throughput and efficiencies. In addition, the refractory ore treatment options are also discussed.IntroductionThe Bell Creek Mill is located in the Timmins Goldcamp approximately 8km NE of porcupine Ontario. (Fig I.)The mill was originally constructed by Camamax in 1987 to treat the Bell Creek ore at a design throughput of 350tpd. The flowsheet (Fig 2.) consisted of two stage crushing, grinding, thickening, leach and drum filtration with gold recovery by Merrill Crowe.As ore depleted at Bell Creek, the Mill was purchased by Falconbridge to process ore from their Hoyle Pond property. Kinross purchased the Hoyle Pond property and Bell Creek Mill from Falconbridge in 1992.The successful exploration program at Hoyle Pond has led to several expansions and process design changes, with further changes planned over the next twelve months.In 1994, the mine produced 61,865 oz. of gold at an average cost of 197US$ per oz. In 1995 production was 91, 611 oz. at a cost of 187US$ per oz. Projecting the nine months ended September 30, production for 1996 will be 155,000 oz. at a cost of 165US$ per oz.In early 1997, the CIP expansion will be complete, with a target of 175,000 oz. at a cost of 176US$ per oz for 1997. The mill throughput will have increased from 400tpd to 1500tpd between 1994 and 1997.The changes to Bell Creek since 1994 have been numerous with very little of the existing equipment still in operation. The total cost of the expansion to date is 15 million C$. This paper discusses the major projects carried out during in this time. The focus will be to highlight the justification of each project, the design and engineering, some of the initial start-up problems and solutions.Figure 3 shows a plan of the existing mill facility together with the various additions that were carried out."

Jan 1, 1997

By M. Gaumont, F. Robichaud

"Agnico Eagle Mines Limited (AEM) is a Canadian-based gold producer with operations in Canada, Finland and Mexico. In 2010, AEM produced its first gold bar in Nunavut, Canada as it started its Meadowbank operation. It is also in 2010 that AEM acquired the Meliadine property, which is located 25 Km North of Rankin Inlet, Nunavut, Canada. The Meliadine gold project is an advanced exploration and development project, comprising of workers camp, underground and open mines, a processing plant and all the services facilities and infrastructures required to sustain operation in a remote arctic environment.Pending formal board approval, production start-up is planned for Q3 2019 and the process flowsheet is based on an ore processing rate of 1.1 million dry tonnes per year (3,000 dry tonnes per day from underground mining) for the first three years, and 1.98 million dry tonnes per year (5,000 dry tonnes per day from both underground and open pit mining) for the remaining years at 92% process plant availability.To the end of 2015, more than 45 metallurgical test programs have been conducted on the Meliadine deposits. Based on the results of these programs, an optimal gold circuit was designed, comprising of crushing, grinding, gravity separation and cyanide leaching with a carbon-in-leach circuit (CIL), followed by cyanide destruction and filtration of the tails for dry stacking. The assumed gold recovery for the reserves averages 96.0% at a 7.44-g/t gold average mill feed grade."

Jan 1, 2016

By D. D. Tannant

An experimental and numerical study was conducted on the geomechanical behaviour of oil sands during penetration tests in which a steel wedge with an apex angle of either 20 degrees or 30 degrees was forced into compacted oil sands. The boundary conditions simulated in the laboratory tests are similar to shovel penetration into oil sands. The objective of the laboratory tests was to measure the force required to push a steel wedge into compacted oil sands. A wedge penetration test differs from conventional triaxial tests in that much more shear is generated. The laboratory data was needed to improve calibration of micro-mechanical input parameters for a two-dimensional discrete element model of oil sands constructed with Particle Flow Code (PFC). Initial model calibration was performed with triaxial test data and then a PFC model of the wedge penetration test was constructed. The measured force-displacement behaviour of the steel wedge was compared with PFC modelling results. It was found that different combinations of PFC particle and bond parameters could equally well replicate the laboratory triaxial compression data for bitumen-rich oil sands. When the wedge model was run, it was found that the resulting force required to penetrate the wedge into the oil sands was about four to six times higher than that measured. This clearly indicates that further research is required to improve the predictive capability of PFC models of oil sands.

Jan 1, 2002

By J. Molgaard, J. Masounave, J. Prinsen, P. Beaulieu, G. Huard

"A study carried out on behalf of the National Research Council (NRC) indicates that economic losses due to wear in the Canadian mining industry are in excess of $700 million annually. Severe wear, mainly by abrasion, was identified as the most important wear mechanism in terms of possible savings. One way to reduce losses would be the proper use of databases. A joint project of The Canadian Institute of Mining and Metallurgy (CIM) and NRC (Tribology laboratories at IMRI) has been initiated to create a factual database containing all relevant experience in the area of wear in the Canadian mining industry. As a first step, a prototype covering slurry pumps is being built. This should help to answer many questions, such as the number of people involved, interest from industry, cost vs benefits, etc.IntroductionTribology is concerned with the understanding of the mechanisms of friction, wear, and lubrication.Tribology is concerned with the correct use of materials for interacting solid surfaces, with the interaction of those surfaces with lubricants, with the chemistry, physics and use of lubricants and their additives. It is concerned with the reduction of friction and wear (or, in the case of belts, brakes, clutch plates, and similar devices, in achieving optimum friction with minimum wear) and is concerned with the avoidance of associated failures in machinery.Lubrication is usually the solution to a problem of friction and wear. Yet far from all the problems of friction and wear are solved by lubrication. The wear of grinding rods or shovel track pads can hardly be solved by lubrication, to name just two examples with which mining engineers will be familiar. There are indeed many situations of wear and friction where the surfaces in contact are unlubricated.In part, tribology is a matter of design. A major aspect, however, has to do with the choice of materials, to satisfy external constraints upon the component design or choice. The operating conditions for much industrial equipment, particularly in mining are, often very severe. The development of wear resistant materials, including materials which are applied as coatings, is clearly an important technology from the point of view of tribology."

Jan 1, 1987

By R. Dahlke, J. A. Finch

"A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick Mine Concentrator to investigate the role of gas (air) superficial rate distribution (Jg profile) to the cells in the final Zn cleaning stage (bank of seven cells). Three profiles were tested: Balanced (each cell with same Jg), Increasing (from cell 1 to 7), and Decreasing, along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The Increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was traced to the response of the first few cells. The Increasing profile gave the highest selectivity of sphalerite against non-sulphide gangue (NSG) in these cells with relatively even recovery per cell down the bank (10-15% based on feed to each cell). The other profiles gave lower selectivity and higher zinc recovery in the first cells (up to 25% in cell 1), which combined to reduce overall bank performance. The increased selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG gangue. The Increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.INTRODUCTIONThe performance of a flotation circuit is largely the result of the operator’s response to visual clues. This includes manipulation of the gas (air) input and how it is distributed to cells in a bank. A lack of sensors prescribes this approach. Over the past ten years the Mineral Processing Group at McGill University have developed a set of gas dispersion sensors including one to measure gas superficial rate (or simply “gas rate”), i.e., volumetric gas rate per unit cell crosssectional area, Jg (Gomez and Finch, 2002). The device collects bubbles in a tube immersed in the pulp and infers Jg from the pressure-time curve generated after a valve is closed and air starts to accumulate. The usual units are cm/s. It is robust, reliable and suited for plant use.A version of the Jg sensor was tested extensively during 2000 at Noranda’s Brunswick Mine Concentrator (Dahlke et al., 2001). The results were sufficiently encouraging that a sensor was fabricated to suit local requirements (Insta-Jg). The sensor detected malfunctioning field instruments and flotation mechanisms, and demonstrated that gas distribution to cells in a bank “as found” had no particular pattern, or profile. Preliminary testing suggested that a balanced profile (i.e., all cells with the same gas rate) gave superior metallurgy (grade / recovery down the bank) than the “as found” profile. This observation prompted a focused campaign to explore the impact of the gas rate (Jg) profile, introducing the notion of “gas distribution management”."

Jan 1, 2004

By N. I. Basuki, E. T. C. Spooner

"The Bongara area, northern Peru, contains Zn-Pb mineralization with characteristics typical of Mississippi Valley-type (MVT) systems. The northwest-southeast-trending late Triassic-Jurassic car¬bonate host rocks of the Pucará Group were locally replaced by early (D1) and late (D2) dolomite. Fluid inclusion microthermometric data from dolomite and sphalerite are typical of MVT ore fluids (78° to 187°C; ~15-23 wt.% CaCl2 equivalent), and do not show apparent covariation between temperature and salinity.Homogenization temperature data from D1 and D2 dolomite show a decrease from northern (mean Th = 138°C) to central (mean Th = 126°C) to southern areas (mean Th = 102°C), suggesting fluid flow from north to south. Assuming a geothermal gradient of ~30°C/km and an average surface temperature of ~20°C, the lower temperature limits might approximate the ambient host-rock temperatures, whereas the upper temperature limits may represent minimum temperatures of a deeper aquifer, probably at a maximum depth of ~6000 m. The lower temperature limits are also similar to the estimated temperatures if dolomitization and mineralization took place in the Late Cretaceous at ~2000-3000 m depth, probably during the formation of the Peruvian fold and thrust belt near the present day Peru-Ecuador border.Fluid inclusion data show that the fluids in each studied location had relatively uniform temperatures and salinities during dolomitization and mineralization. A significant salinity drop and a slight temperature decrease are observed during late calcite precipitation, suggesting mixing of brines with dilute, cooler fluids."

Jan 1, 2009

By J. E. Scott, L. M. Heaman, R. A. Creaser, G. S. Salazar

"Schaft Creek is a calc-alkaline porphyry Cu-Mo-(Au) deposit located in northwestern British Columbia. The deposit formed in a volcanic arc setting, likely on a back-arc rifted continental fragment. It is hosted by Late Triassic basaltic to andesitic volcanic rocks of the Stuhini Group (Stikine Terrane), and is associated with porphyritic granodiorite dikes emanating from the nearby Hickman batholith. The age of the Hickman batholith is approximately constrained here by a composite U-Pb zircon date of 222.1 ± 9.6 Ma, which is in broad agreement with a well-constrained age for mineralization at Schaft Creek of 222.0 ± 0.8 Ma (Re-Os molybdenite). The deposit is in most respects typical of calc-alkaline porphyry systems, but displays silica-poor sericite-chlorite alteration in mafic country rocks in place of classic phyllic altera¬tion. The deposit comprises three distinct, but related, zones: the northern Paramount zone, the Main zone, and the West Breccia zone. Two phases of mineralization are observed. The first phase occurs as hydro-thermal veins and breccias, and minor disseminations. It consists of bornite, chalcopyrite, molybdenite, and pyrite with potassic and sericite-chlorite alteration. The second phase is minor and consists of veins of molybdenite ± specularite, as well as Cu-Pb-Zn sulfide veins without any significant corresponding alteration. Extensive structural modification has affected the deposit both during and after its formation.Schaft Creek est un gîte porphyrique de Cu-Mo-(Au) calco-alkalin situé dans le nord-ouest de la Colombie Britannique. Ce gîte s’est formé dans environnement d’arc volcanique, probablement situé sur un fragment continental bordé par un bassin d’arrière-arc. Le gîte est encaissé par les roches volcaniques basaltiques à andésitiques du Groupe de Stuhini (Terrane de Stikine) d’âge Triasique tardif, et est associé à des dykes de granodiorite porphyrique provenant du batholithe de Hickman avoisinant. L’âge du batholithe de Hickman est estimé par un âge U-Pb composite sur zircon de 222.1 ± 9.6 Ma, lequel est grossièrement en accord avec l’âge de la minéralisation de Schaft Creek, estimé a 222.0 ± 0.8 Ma (Re-Os sur molybdénite).Ce gisement, bien qu’à plusieurs égards typique des systèmes porphyriques calco-alcalins, présente une altération en séricite-chlorite pauvre en silice dans l’encaissant mafique a la place de l’altération phyllique classique. Ce gîte comprend trois zones distinctes bien que connexes : la zone Paramount au Nord, la zone Principale et la zone West Breccia. Deux phases de minéralisation sont observées. La première phase se présente sous forme de veines et de brèches hydrothermales ainsi qu’en disséminations mineures et consiste en bornite, en chalcopyrite, en molybdénite et en pyrite avec une altération potassique et en séricite-chlorite. La seconde phase est mineure et consiste en veines de molybdénite ± spécularite ainsi qu’en veines de sulfures de Cu-Pb-Zn sans association à une altération particulière. Le gisement a été profondément modifié par la déformation a la fois durant et après sa formation."

Jan 1, 2008

By Barara Rose

Presentation Outline ?Introduction of BMS ?Resource Integration Process ?Methodologies ?Tools ?Case Studies ?Zone 01 : 725 SOZ ?Zone 16/17 : 1000 NRP ?Conclusions

Oct 1, 2010

By Nessetech Consulting, L. A. Cisternas, E. D. Galvez, S. H. Kuan, L. H. Saw

"In Malaysia, there were two rare earths processing plants namely Asian Rare Earth (ARE) and the Malaysian Rare Earth Corporation Plant (MAREC) in Perak, which were operated until 1992 and were subsequently closed due to problems pertaining to disposal of large amount of radioactive waste. Recently, Lynas Advanced Materials Plant (LAMP) has become one of the largest rare earths processing plant in the world producing rare earth elements (REE) in Gebeng, Pahang. The primary raw material is lanthanide concentrate (LC) which is imported from Mount Weld mine in Australia and shipped to Malaysia. LC is produced from lanthanide ore after mining and mineral processing. The ore has a lower impact than Bayan Obo, Mountain Pass and adsorbed clay deposits, given the small footprint of the mine itself and the remoteness of the location. The type of ore being mined (rare earth phosphates: carbonatite, monazite) may have higher thorium content than bastnasite ore from the Chinese or American mines but still far below radiation concerns. This paper was written to review the processing flowsheet at the Lynas Advanced Materials Plant (LAMP), the environmental impact associated with the processing of the said ores and the sustainability of the operation.INTRODUCTIONRare earth minerals are one of a set of 17 minerals or chemical elements which consists of yttrium and scandium, as well as the 15 lanthanide elements (lanthanum, cerium, praseodymium, neodymium, promethium, europium, gadolinium, terbium, dysprosium, holmium, erbium, thulium, ytterbium, and lutetium). Despite their importance, rare earth minerals rarely exist in economically viable concentrations and they are usually difficult to extract. Rare-earth minerals create strong magnets when added to magnetic elements such as iron, and are useful for the production of electronics systems as well as electric cars. They are also used extensively in automotive catalytic converters, fluid cracking catalysts in petroleum refining, wind turbines, phosphors in colour televisions and flat panel screens, displays for mobile phones and laptops, rechargeable batteries, and various medical devices. The elements are typically split into two subgroups: the cerium sub-group of ‘‘Light’’ rare earth elements (LREEs) which includes La to Eu and the yttrium sub-group of ‘‘Heavy’’ rare earth elements (HREEs) which include the remaining lanthanide elements, Gd to Lu, including yttrium (Gupta and Krishnamurthy, 1992; Jordens et al., 2013; Trifonov, 1963). Scandium, however, when it is classified as a rare earth element, is not included in either the LREE or HREE classifications (Gupta and Krishnamurthy, 1992; Jordens et al, 2013). Half of the world’s 110 million tons of reserves exist in China while other sizable deposits are found in Russia, United States, Brazil, India, Australia, Canada, and Greenland. The countries known to be actively mining REE are China, Russia, India, Brazil and Malaysia (Hao et al., 2015). Among these countries, China has the largest REE production, accounting for more than 93% of global supply (Yap, 2015). The critical metal report (Moss et al. 2011) listed 14 economically vital raw materials that are prone to supply disruption and concluded that supply disruption would threaten the goal for cleaner transport and sustainable energy since rare earth metals are used in products using green technology, such as hybrid/electric vehicles, carbon capture systems, wind power generation, low-energy lighting, and energy efficient flat-screen displays."

Jan 1, 2016

By C. A. Pickles, D. K. Xia

"In the last few decades, microwave energy has been widely employed in food processing, rubber and plastics curing, and in ceramic sintering. Recently, the application of micro waves as an energy source in extractive metallurgy has received considerable attention from a number of researchers. During the period from the mid-1960s to about 1988, the majority of the research was focussed on the behaviour of materials in microwave radiation. These research activities will continue to be important, since fundamental data on the interaction of microwaves with materials are vital for the successful application of the technology. Since1990, a number of potential applications of microwave processing have been investigated.These include: pretreatment of ores and concentrates, leaching, reduction, preheating of refractories, heating of slags and waste treatment. In this paper, the interaction of micro -waves with materials of interest in extractive metallurgy are reviewed and potential applications are discussed.IntroductionMicrowaves were first used in 1946 for the heating of materials, shortly after radar equipment was invented during the second world war. It was evident that microwaves were very effective for heating water and the technology was quickly adopted for drying and cooking. Since the introduction of the first microwave oven by Raytheon in 1952, many millions of domestic microwave ovens have been sold annually (National Research Council,1994; Atomic Energy of Canada and Voss Associates Engineering, 1990).In extractive metallurgy, microwaves are in the early stages of development (National Research Council, 1994; Atomic Energy of Canada and Voss Associates, 1990; McGill and Walkiewicz, 1987; Bradhurst and Worner, 1990;Peng et al., 1993). However, there are several reasons for the growing interest in the use of this technology in the field of metals extraction. These include the following potential advantages of microwaves: (1) rapid and selective heating of materials; (2) reactions can be catalyzed because the heating occurs on a molecular or atomic level; (3) clean and controllable energy source; (4) the gas volume is reduced and the atmosphere can be controlled as there are no gaseous combustion products; (5) the material is heated internally in comparison to external heating with conventional methods; (6)the temperature of the refractory can be minimized; and (7) the working environment is improved."

Jan 1, 1997

By Dave Rose, David G. Meadows, Mike Westendorf

"Copper Mountain’s concentrator was commissioned in May 2011. The circuit consists of a 34’ x 20’ EGL SAG mill, a Raptor 900 pebble crusher and two 24’ x 39’6” ball mills. Each mill is equipped with a 2 x 8500 HP dual pinion drive system. The plant was designed to process 1585 mtph of SAG feed. From startup, the mill struggled to meet the required production rates. Over time, a major initiative that involved blasting and fragmentation, optimization of the SAG mill in terms of discharge grates, ball size and slurry density, and operation of up to three mobile pre-crushing plants resulted in significant increases in throughput. In parallel, a number of modeling tools, including JK SimMet, were run based on plant benchmarking exercises. Samples collected at the mine site during ramp up confirmed the very competent nature of the ore with drop weight - A*b values of less than 24 being recorded on a variety of plant feeds and lithologies. After due consideration including demonstration of proof of concept, a new pre-crushing circuit incorporating an XL2000 cone crusher and associated screening equipment was designed, constructed and commissioned at the site in August 2014. This paper reviews the history of the original circuit design, the various optimization steps taken and impacts, together with the final pre-crushing circuit and net results.IntroductionThe Copper Mountain Mine is located approximately 20 km south of Princeton, British Columbia, Canada (refer to Figure 1). The region has a long history of copper mining dating back to 1923. The Copper Mountain camp occurs in the 'eastern volcanic belt' of the Nicola Group (Monger, 1989). It is an alkali copper-gold deposit in which the volcanic strata are intruded by early Jurassic dykes, sills, irregular plugs and zoned plutons (Woodsworth et al., 1992). The stratified rocks are relatively fresh with slight metamorphism in the local contact regions."

Jan 1, 2016

By Jane Li, Kevin Tom

"Research has shown that broken rock on conveyor transport systems can contribute upwards of 50% towards the overall heat load in underground mines. However, few studies have made significant efforts to predict the temperature distribution of the ore and air simultaneously, which can help implement heat management strategies. The present investigation explores a transient, analytical heat transfer model to track ore-pile temperature distributions, along conveyor systems in an example underground mine. Production rate, ambient conditions, ore pile thickness and belt velocity are adjusted to evaluate the effect on dry and wet bulb temperatures.INTRODUCTIONWith an ever increasing demand on Earth’s resources due to a multitude of factors like population growth and step changes in technology, pressure on the mining industry to bring out more ore with improved margins is a persistent challenge. Typically, high-volume producing mining methods (i.e., exceeding 5000 tons per day (tpd)) such as sublevel and block caving, room and pillar, and longwall shall utilize belt conveyors instead of trucks as the primary haulage method to surface to save on operational costs (de la Vergne, 2014). However, studies have shown that when such material transport systems are installed at mine depths with virgin rock temperatures (VRT) above 40oC, the heat dissipated by the conveyed ore can account for over 50% of the underground heat-load (Pareja, 2000; Bluhm, Jones, Moreby, & von Glehn, 2012; van den Berg, Moreby, & Kok, 2015).Unlike other types of heat sources encountered in underground mines, such as diesel machines, strata, electrical devices, and autocompression, heat transfer by conveyed broken rock is much more difficult to estimate. The seminal work of McPherson (1993) states that broken rock heat transfer is a function of its surface area, and the air’s psychrometric condition. It is additionally a function of the VRT, its specific heat, production rate, heat transfer coefficient and the residence time (Bossard, 1997; Ross, Tuck, Stokes, & Lowndes, 1997). Consequently, few studies have attempted to analytically quantify the significance of ore heat flow."

Jan 1, 2019

By Mohammad Noaparast, Babak Fotoohi

"Due to certain advantages in (semi-)Autogenous-Ball mill circuits in most of the high-throughput ore grinding units of mineral processing plants, much attention is paid to optimize the mill performance. Despite the maturity of the grinding mill mechanical design, there had been made less attention to the efficiency of the grinding media in the past. In this research, the possibility of establishing a relationship between liner/lifter wear rate and variations in the composition of the iron ore (from Chadormalu mine) is investigated.Measurements and determination of liner/lifter wear rates and patterns concluded in recognition of critical liner segments exposed to much abrasion during the ore grinding. After metallurgical analysis of liner materials and correlation of wear rate with the ore composition, the homogeneity in the metallurgical microstructure of the alloyed steel (such as the uniform distribution and amounts of the constituent phases) was determined as the most influential factor in the response of the liner/lifter to the variations in the ore composition. Magnetite with greater abrasion index than hematite, in finer particles, is responsible for additional abrasion of liners; hematite with greater work index exists in the mill with larger particle sizes, thus it could produce wear on liner parts with less tolerance to impact as is the situation for martensitic steels.INTRODUCTIONThe mineralization in Chadormalu plutonic iron ore deposit is consisted of mostly magnetite, hematite, martite, apatite, quartz and carbonates. The average composition of the ore is presented in Table 1. In the processing circuit, the gyratory crushed ore reduced to 30 cm would finally be the feed to three similar 32’ semi-autogenous mills in parallel processing lines. The pulp in the mill would have the characteristics mentioned in Table 2. The quality of the mill output has its direct effect on the downstream processes either physically or chemically (e.g. in cycloning or flotation respectively). In order to take advantage of optimum performance for these circuits, a close control of the ore grinding conditions is necessary; because any shortages in throughput, liner/lifter damage or changes in ore composition could bring the unexpected casualties. In this work, it has been attempted to find (possibly) a reasonable relationship between variations in ore characteristics together with liner quality and the amount of wear rate in different liner/lifter segments of a semi-autigenous mill. Liner/lifter segments are supplied by three different domestic steel making companies. The alloy structure of the liners/lifters is made up of pearlitic chromoly steel."

Jan 1, 2005

By Carolyn Kenney, Jianjun Liu, Zhenghe Xu

"The flotation of fine particles has been a challenge to scientists and engineers in mineral processing. A novel concept of reactive oily-bubbles as carrier to float fine particles is described in this paper. The reactive oily bubble flotation is considered attractive for fine particle flotation. In addition to the role of fine particle agglomeration by oily films, the surface properties of air bubbles coated with a thin oil film can be better controlled for the desired selectivity by adding certain types and concentrations of water insoluble collectors into the oil phase. This approach can eliminate the addition of collector to the aqueous phase, avoid undesired synergetic interactions among collectors, activators, depressants and dispersants present in slurry, minimize undesired activation of gangue particles and significantly reduce the amount of collectors needed.The concept of using reactive oily-bubble to achieve selective flotation was demonstrated in contact angle measurement and by microflotation tests with fine sulphide minerals: sphalerite and galena in this paper. The flotation behavior of sulfide minerals can be radically modified with adjustment of solution pH, addition of depressant and activator as in conventional flotation. The successful separation between PbS/SiO2, ZnS/SiO2 and PbS/ZnS was demonstrated using mixed mineral systems. Compared with conventional flotation, the reactive oily-bubble flotation showed a stronger collecting power.INTRODUCTIONThe challenge for fine particle flotation has long been recognized and well documented (Fuerstenau, 1980). Because of drastic changes in surface properties of fine particles and associated physicochemical and hydrodynamic conditions of flotation systems, fine particles responded poorly to the conventional flotation processes. For instance, the small mass and hence low inertia of fine particles would result in a low efficiency of collision and attachment of fine particles with flotation bubbles. Large specific surface area of fine particles, on the other hand, would cause an increased reagent consumption. Dominating colloidal forces of fines may cause slime-coating, accompanying a low selectivity (Somasundaran & Arbiter, 1979; Fuerstenau, 1980; Sivamohan, 1990)."

Jan 1, 2003

By E. LaRocque

"Denison Mines Limited has been processing uranium ore in the Elliot Lake area since May of 1957. The ore body is located i11 the Huronion sediments on the north limb of the Quirke Lake syncline. Minerals of metallurgical significance are brannerite, uraninite and monazite. Gangue minerals include quartz, chlorite, sericite, pyrite, pyrrhotite and rutile. Silica content of the ore is greater than 75 % and pyrite-pyrrhotite content around 7 %. Specific gravity of the ore is 2.75.The Denison flowsheet is based on sulphuric acid leaching to extract the uranium values from the ore followed by liquid-solid separation to wash the uranium-bearing solution from the barren ore. The resultant pregnant solution is concentrated and purified by ion exchange followed by two-stage precipitation with ammonia to produce an ammonium yellow-cake.Elliot Lake ores require high acid concentrations and high temperatures to extract the uranium from brannerite and monazite. Uraninite will leach at low acid concentrations as long as oxiclizing conditions exist. The whole ore must be treated so that these conditions do exist.This paper provides a description of the leaching process equipment as originally installed and major changes in that equipment to date. Process control refinements to economically improve extraction are also discussed."

Jan 1, 1979

By Bern Klein, Malcolm Scoble, Justin Widdifield, Andrew Bamber

"It has been suggested that the pre-concentration of ore underground can bring positive economic and environmental benefits to underground mining, particularly at extreme depth. The integration of mineral processing systems for coarse waste rejection and disposal into the underground mining environment has a substantial impact on the economics and operation of the mine. A case study for the integration of underground pre-concentration at Falconbridge’s Thayer Lindsley and Fraser Copper operations in Sudbury, Ontario is discussed, with particular focus on ore evaluation, system design, integration, and impacts on the operation. Conclusions as to the overall feasibility and potential impacts of underground pre-concentration are presented.INTRODUCTIONObjectivesA scoping investigation has been conducted for Falconbridge Ltd on the Fraser Copper Zone and Thayer Lindsley mines in order to develop a better understanding of the operations, and to do a preliminary evaluation of the potential for pre-concentration of the ore underground. The objective was to develop a conceptual design and evaluation of a pre-concentration system for each site. The results are to be used as the basis for a more detailed future study.Underground Pre-ConcentrationThe pre-concentration of ore to reduce the quantity and improve the quality of material transported to the processing plant is not a new concept and has been in practise at several mines including the American Zinc Company in Mascot Tennessee (Munro et al, 1982), the Sullivan Mine in British Columbia and presently at Xstrata’s Mt Isa lead-zinc mine in Australia, as well as at several PGM mines operating in the South African Bushveld. For each of these mines, a high degree of waste rejection was achieved at a coarse particle size with good metallurgical recoveries. The benefits arising from the surface pre-concentration of ore are well documented in the literature (McCullough et al, 1999; Miller et al, 1978; Munro et al, 1982; Schena et al, 1990; Sivamohan & Forssberg, 1991)."

Jan 1, 2006

By Ali Mortazavi

In underground mining applications, successful blasting results in less damage, which may lower support costs, lower dilution and produce a uniform fragmentation. The explosive detonation process creates a pressure front that propagates a stress wave into the surrounding rock mass at a high velocity. The stress wave can induce varying degrees of damage, depending on rock strength and physical properties, to the excavated area. This paper presents a summary of a research project that was conducted to investigate the propagation of explosive-induced stress waves in hard rock media and the mechanism of rock damage and fracturing due to shock wave propagation. The primary objective of this work was to numerically simulate the experimental study of blast-induced rock fracturing conducted within Inco Limited, Mines Research department. ITASCA?s discontinuum code UDEC (Universal Distinct Element Code), was used to simulate the results of the controlled blasting experiments. In brief, the focal point of the paper can be summarized as follows: ? Investigate the size of the stress-wave-induced fractured zone around the blasthole, ? Examine the extent and direction of the radial fractures that form outside the blasthole, and ? Explore the mechanisms that cause rock breakage.

May 1, 2002

By S. Banisi, H. R. Iran-Manesh, M. R. Shayestefar, H. Shekarchyan

"Flotation circuit of the Sarcheshmeh copper mine processes 41,000 t/d of ore at 0.9% Cu. Chalcopyrite and chalcocite are the main copper bearing minerals which are concentrated in three stages of roughing, cleaning and recleaning. Due to major changes in the reagent addition regime, make-up balls combination, and throughput to the primary mills an increase of 2.6% (from 87.2% to 89.8%) in the sulfide copper recovery was obtained during a period of six years. In order to investigate a rather large variation of monthly recovery (i.e., from 89.0 to 91.2%) of the plant after implementation of the changes, a study was undertaken to trace mineralogically possible causes of such a behavior. During a five-month period, monthly composite samples of feed and tailings of the flotation circuit were taken. At the first stage, the polished sample preparation method and the mineral counting procedure were optimized through a detailed study. Liberation degrees and types of locking of valuable minerals in both streams were determined in three size intervals of +75, +38 and –38 microns. It was found that for both recovery levels (i.e., 89% and 91.2%), there was no significant difference in the liberation degrees of valuable minerals in the flotation feed; the average liberation degree was 57.1% with a standard deviation of 3.1%. On the other hand, in the case of high recovery level (i.e., 91.2%) there was a reduction of 15% in the amount of free valuable minerals in the tailings stream. The highest reduction was found for the -38 micron size range in particular for chalcocite. It was concluded that compared to the grinding circuit the change in the flotation circuit had the significant effect on the plant recovery increase.INTRODUCTIONThe Sarcheshmeh copper ore body contains 1 billion tonnes averaging 0.90 % copper and 0.03 % molybdenum. It is located southeast of Iran and currently processes 41,000 t/d of ore. The concentrator has been in operation since 1982. Last year, the concentrator produced 130,000 tonnes of copper and 4,000 tonnes of molybednite concentrate. An expansion to the plant which will increase the throughput by 50% is under construction and will be effective in 2003.After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailings constitute the main component of the plant final tailings. A concentrate with an average grade of 30.5% Cu is obtained after cleaning and re-cleaning stages. At the present time, the average sulfide copper recovery of the plant is 89.8% which varies depending on the operating conditions and ore type."

Jan 1, 2003

By R. H. O. Wagner

"This paper describes the bench testing, pilot plant studies of alternative flowsheets, to determine the feasibility of gold recovery, by carbon in pulp extraction, in the Schumacher Mill gold flotation tailings. The economics were calculated based on pilot plant recoveries and actual industry operating costs.The economics of the carbon in pulp treatment of the gold flotation tailings were not justifiable. The economics of desliming the gold flotation tailings followed by carbon in pulp treatment were marginal, but favourable. INTRODUCTIONPamour Porcupine Mines, Limited is a gold, silver and copper producer located in Timmins, Ontario. In 1983 the head grade of Pamour's gold ores averaged nine one hundredths of a troy ounce of gold per short ton.Pamour operates two area mills to concentrate the gold ores. Free milling gold ores are processed at the Pamour One Mine mill, whereas the refractory carbonaceous gold ores, and complex gold, silver, and copper sulphide ores, are processed through the Schumacher Mine mill.The complex Schumacher mill feed ores do not all react favourably to flotation methods, consequently this study was commissioned to investigate the feasibility of the carbon in pulp cyanidation of the Schumacher mill gold flotation tailings. These tailings contain ten to fifteen percent of the gold in the mill feed. During the study period, the average grade of the Schumacher mill flotation tailings was nine one thousandths of a troy ounce of gold per ton, or one quarter of a gram of gold per metric tonne."

Jan 1, 1984

By D. Kidby, A. Briggs

"Vitrokele ™ is a synthetic adsorbent, using chelating groups on large polystyrene beads, developed in Canada over 7 years ago, and first commercialised in 1985 to recover noxious metals from plating wastes.Pilot plant trials have been performed in Australia and Canada to demonstrate the recovery of cyanide and removal of metal cyanide complexes from gold plant effluent using Vitrokele1 M 912. The pilot plants comprise a simple adsorption train (similar to a CIP circuit) followed by complete elution facilities, so that loaded Vitrokele™ can be stripped and returned to the adsorption circuit.An account of these campaigns is provided, showing the reduction of total CN levels from over 200 ppm to less than 0.5 ppm and Cu levels from approximately 100 ppm to less than 0.3 ppm in treated tailings.Comparisons between pilot plant results and laboratory test data are given and probable future work on the process and its application to the gold mining industry is discussed.INTRODUCTIONThrough millions of years of evolution, life forms have developed specialised molecules with exceptionally high affinity and selectivity for various metals such as iron, cobalt, zinc and copper.In the early 80's professors at the Faculty of Medicine of McGill University engaged in research on the extremely efficient ways that living cells captured trace metals essential for life.As research progressed, it became evident that the special molecules used by biological systems to capture metals could be synthesized to capture selected metals with similar efficiency from water or other solutions.The technology was first commercialised in 1985 to recover noxious metals from plating wastes with compositions applying the special molecules (chelating groups) on vitreous particles (hence Vitrokele™). To date approximately three commercial Vitrokele™ plants have been installed for treating plating waters in Ontario and Quebec."

Jan 1, 1992