Search Documents

By R. Maxwell

"At Opemiska Copper Mines we have, over the past four years, operated 300 cu. ft. and 700 cu. ft. flotation cells as roughers, scavengers and cleaners and found them competitive with conventional flotation cells on a cu. ft. basis on all phases of flotation.The economics are very much in favour of the large cells for the following reasons:Power consumption is 35 to 40%, of conventional machinesMaintenance cost is about 20 to 25% of conventional machinesSpace required is about 30 to 35% of conventional machinesInstallect cost is about 40%, of conventional machinesTo put the above in more concrete terms below is what we are doing at Opemiska:1. Increasing mill capacity from 2000 to 3000 T.P.D. and will use only 5Cff, of the flotation space for 3000 tons that we used for 2000 T.P.D. with conventional flotation machines.2. Will require only 10 flotation cells for 3000 tons against 85 conventional cells for 2000 tons.3. Cells will be, one 2000 cu. ft. rougher, six 700 cu. ft. scavengers (2 banks of 3 each) and one cleaning circuit using three 300 cu. ft. cells.You will note that in this 3000 ton per day plant, we are going to have only ten cells. Had we put in conventional cells for this tonnage, we would have needed 120 cells."

Jan 1, 1970

By Chan-ho Park

As the building has recently become bigger, higher, and freeform, a technology called BIM(Building Information Modeling), which is a key technology that integrates construction and IT(Information Technology), has been rapidly introduced and expanded. Because BIM technology offers various benefits, countries that introduced BIM early has been actively promoted. However, misperceptions of BIM are prevalent in countries such as South Korea that have adopted it relatively late, with lack of awareness of its fundamental purposes. Under these circumstances, transparent and quantitative performance assessment needs to be executed in order to eliminate the misperceptions, and to explain and revitalize the BIM introduction. These quantitative performance measure KPI (Key Performance Indicators) to be measured should be prioritized. As derive performance indicators in terms of the four types (financial, customer, internal processes, learning and growth), and performance management systems, Uses the BSC to seek a balance between short-term financial goals, values and the value of long-term goals. Uses the BSC(Balanced Scorecards) to derive performance indicators in terms of the four types (financial, customer, internal processes, learning and growth), and performance management systems, seeking a balance between the value of short-term financial objectives and the value of long-term objectives. Through this, the KPI (Key Performance Indicators) which is used for measuring the effect of the BIM will be generated and also the method that can determine whether the generated KPI figures are objectively inter-connected will be suggested as well.

Aug 1, 2013

By J. R. Shore, F. G. M. Gillett, E. J. Zickar

"The addition of fines to rod mill feed has been employed at Inco Metals' Frood-Stobie Mill since 1973. The fines, which act as a ""lubricant"", causes an increase in the pulp fluidity and assists the flow of feed through the rod mill. Fines addition was one of the main factors which led to improved rod mill performance and the elimination of rod mill tangles.This paper outlines the testwork performed in evaluating the addition of fines, and summarizes the beneficial effects on rod mill grinding efficiency, throughput rates, power consumption and noise level. INTRODUCTIONFrood-Stobie Mill is situated within the Frood-Stobie mining complex, on the southern rim of the Sudbury Basin. The Mill commenced operations in November, 1967, and has since processed in excess of sixty-five million tons of ore. Minus 8-inch ore is delivered to the Mill's coarse ore bin by two surface conveyor belts from the Frood and Stobie Mines, while Little Stobie ore is transferred by underground conveyor and hoisted directly into the coarse ore bin a long with additional Stobie Mine ore."

Jan 1, 1981

By Robert B. Parsons

"The February 18, 1987, Federal Budget contains a proposed amendment which would simplify somewhat the ""successor corporation"" rules in the Income Tax Act. Despite this amendment, though, the important successor rules will continue to be relatively complex.IntroductionThe February 18, 1987, Federal Budget papers propose an income tax amendment whereby the so-called ""successor corporation"" rules would be revised by removing the present provision which limits the application of these rules to a maximum of two ""successions"". The successor corporation rules represent one of the most complicated sets of rules in the Income Tax Act. This month, Tax Notes seeks to explain these rules and the proposed amendment in simplified terms.Basically, the successor rules provide a mechanism for transferring unused exploration and development expenses from one taxpayer to another , in specified circumstances. The aforementioned limitation of two successions refers to the rule which allows a maximum of two such transfers with respect to any particular pool of deductions."

Jan 1, 1987

By H. J. Oterdoom

SMS Siemag (SMS) has always been the front runner in safety aspects of electric smelter plants for the ferro-alloy and non-ferrous industry. The awareness for safety increased significantly over the past decades and SMS contributed with its design features greatly to a safer design and operation. Today, safety aspects are not only part of the smelter design but also of the overall plant layout. Explosions in electric smelters are rare, but have a huge impact on peoples’ lives, on equipment and on production. For this reason, SMS wanted to have a better overview of explosions within the smelting industry in order to see if useful statistics could be extracted. Generally, there is a lack of statistics regarding explosions in the electric smelting industry, and not enough information is collected or published. A significant portion of the explosions seems to be water related. Many companies, both operating and engineering, are trying to handle the risks of water, and apply methods to detect water leakages. Installing such a system is a management decision and management has then to make sure the system is properly implemented. The disadvantages and limitations of these systems should be carefully considered and communicated to operators and authorities.

Jan 1, 2014

By Kadri Dagdelen

Recent trends of the mining project show that there will be more and more mechanized, largescale mining operations with complex process options to make low grade deposits economically feasible to develop. The global optimization of large scale, complex mine operations will become more important for the future mining. To serve the industry?s future needs, the OptiMine® software program is developed based on expertise gained at the Colorado School of Mines (CSM) for more than two decades, by using the special solution methodology based on the Mixed Integer Linear Programming (MILP) technique in the Operations Research (OR). The program has been beta-tested on more than 20 projects as a multi-time period scheduling and cutoff grade optimization tool that handles large scale open pit and underground mining operations involving complex process options, many stockpiles and dumps, blending requirements, and truck hour limitations. In each project, various operational options are evaluated in OptiMine® to develop strategic planning to help defining company?s strategies and directions. This paper demonstrates how the OptiMine® can be used to optimize a large scale, complex production scheduling problem on a case study coming from real world project. The case study describes multi-pit mine production scheduling optimization with pit backfills in such a fashion that acid generating waste rocks are encapsulated to minimize environmental impact.

Oct 1, 2009

By L. A. Gomieroa

The Caetité-Brazil uranium facilities produce about 340 t/y of uranium from an ore averaging 0,25 U %. The process steps are ore crushing, heap leaching with sulfuric acid, U separation and purification by solvent extraction with tertiary amine followed by stripping with sodium chloride solution and precipitation as ammonium diuranate that is dryed. A change in the milling process is being evaluated to increase the production and the uranium recovery. Heap leaching will be changed to conventional tank agitated leaching of the ?590 ground ore slurry in sulfuric acid medium. The replacement of the stripping reagent is also being considered.

Aug 1, 2010

By Simon C. Dominy, Patrick R. Stephenson, Alwyn E. Annels

Abstract - The often complex, erratic, and localized nature of gold is a common feature of many vein-style gold deposits. This style of mineralization is often referred to as being nuggety or possessing a high-nugget effect. As a result of these complexities resource estimation is difficult and in general, only Exploration Results can be provided or an Inferred Mineral Resource estimated from surface drilling data alone. Underground development, further drilling, and probably bulk sampling will be required to delineate Indicated and Measured Resources. Tonnages can generally be estimated from diamond drill and development information with a reasonable degree of confidence. Grade is much more difficult to define with confidence because it is commonly highly erratic and discontinuous in nature. The dependency of higher confidence Resource categories on development information may create a Catch 22 situation, with funding for such development often depending on the prior definition of at least Indicated Resources. There are no easy solutions to these challenges posed by high-nugget effect deposits, and it is important when classifying and reporting not to downplay the uncertainties often associated with Mineral Resource and Ore Reserve estimates for such deposits. However, in common with all deposit types, if the principles that underpin the estimation, classification, and reporting procedures are borne in mind and common sense applied, most issues can be satisfactorily resolved. This paper discusses the classification and reporting of Mineral Resources for high-nugget effect gold vein deposits within the framework of the JORC Code (JORC, 1999).

Jan 1, 2001

By Guy Chevalier

QCM?s pellet plant, located in Port-Cartier, Quebec, produces up to 8.6 million tons of iron ore pellets annually. Four different types are produced: three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the installation of new process equipment to improve the reducibility of direct reduction pellets (DR pellet). The findings, the equipment selection and some post start-up modifications are presented. This low silica DR pellet is used in Midrex and HyL shaft furnaces. A good DR pellet has to meet strict chemical, physical and metallurgical specifications. An important metallurgical property is its ability to release oxygen when exposed to reducing gases. Considering that the market for DR pellets is expanding and being aware that reducibility is critical for our clients, a program to improve the latter was undertaken. Test work showed that one factor which has a negative effect on reducibility is the proportion of particles larger than 75 microns. Knowing that the best way to reduce the amount of coarse particles was to close our open grinding circuits, we began evaluating the most suitable classification equipment applicable to our process operations. We settled on hydro-classifiers based on their very sharp cut and their low operating costs. In light of the hydro-classifiers performance it was also decided to replace the hydro-cyclones of an already closed circuit.

May 1, 2003

By M. P. Amsden

"Ecstall Mining Limited, a subsidiary of Texasgulf, Inc., Operates the Kidd Creek Mine, Concentrator and Zinc Plant at Timmins, Ontario. Two different ore types are mined and milled to produce concentrates of copper, zinc, lead and tin. The ores are processed at the Concentrator in three separate individual milling circuits, each with the capacity to treat up to 3500 tons per day. Two circuits treat copper-zinc ore 1t an average combined rate of 6500 tons per day and the third circuit treats 3500 tons per day of silver-lead zinc ore. Conventional crushing, grinding and flotation procedures are followed. The purpose of this paper is to describe Ecstall's experience with rubber mill linings in the grinding circuits.CrushingBoth ores are crushed to minus 6 inches at the Mine and delivered by rail to the Concentrator where they are reduced by secondary and tertiary crushing to minus 5/8 inch.GrindingThe crushed ores are prepared for selective flotation by grinding with rod mills and two stages of ball milling. flotation circuit middling products are reground in regrind mills prior to further treatment. A typical flowsheet of one of the grinding circuits is shown in Figure 1.All the grinding units are Allis-Chalmers Mills. The rod mills are 10 1/2 feet diameter by 16 feet long. Both the primary and secondary ball mills are 12 feet diameter by 18 feet long and all regrind mills are 6 feet diameter by 12 feet long. The primary mills are charged with 1 13/16 inch forged balls. Secondary mills are charged with 1 1/2 inch forged balls and the regrind mills are charged with 1 inch forged balls. All cyclones are Kreb units. The primary cyclones are Dl5B hydrocyclones, the secondary cyclones are D6B hydrocyclones and all regrind cyclones are D6B hydrocyclones."

Jan 1, 1974

By Henri-Louis Jacob

Le Québec dispose de ressources en silice abondantes et diversifiées, pouvant convenir dans l'ensemble à la plupart des usages industriels. Dans les terrains Paléozoïques des BassesTerres du Saint-Laurent et des Appalaches, les ressources identifiées comprennent les grès quartzitiques purs du Croupe de Potsdam (Cambrien), exploités notamment à Saint Canut au nord de Montréal comme source de sable de silice pour l'industrie du verre; les arénites quartzitiques des Formations de Val-Brillant (Silurien moyen) et de Kamouraska (Ordovocien inférieur) exploitées dans l'est du Québec comme source de fondant métallurgique; les grès friables de la Formation de Guigues (Ordovicien) au Témiscamingue, à partir desquels on produit des sables de silice utilisés notamment en fonderie et en filtration. Dans la province structurale du Grenville, au nord du fleuve Saint-Laurent, les métaquartzites purs du Supergroupe de Grenville représentent une source importante de silice pour la production de silicium, de ferro-silicium et de carbure de silicium. Des veines et amas de quartz ont aussi été exploités un peu partout au Québec comme source de fondant métallurgique ou de silice ultra-pure pour la production de silicium métal. Quelques dépôts de sables naturels, généralement d'origine marine ou deltaïque sont finalement exploités dans la région de Montréal comme source de sable pour des usages n'exigeant pas un produit de haute pureté.

Jan 1, 2001

By M. Timberlake, A. J. Jonaitis

"The DENVER Tube Press is a simple, high pressure (1500 PSI (100 bar)) filtration unit, developed for processing difficult-to-dewater materials and to produce a handleable filter cake and clear filtrate product.Lab and Pilot testwork conducted in Australia on coal fines (55-70% -35 micron (400 mesh)) have shown that total moisture contents of less than 20% are consistently achieved in the final cake products from the Tube Press.currently, these coal super fines are sent to waste due to uneconomical mechanical dewatering methods, which were only able to reduce total moisture levels in excess of 30%. Calculated, throughput rates for the 500 series Tube Press exceeded 1700 kg/hr (3750 lbs/hr). Feed solids concentration requirements are between 45 and 50% to achieve these results.INTRODUCTIONThe DENVER Tube Press is an automatic membrane high pressure filter press, which operates at hydraulic water pressures up to 1500 PSI (100 bar). The Tube Press was developed in the late 1960's by Charlestown Engineering, st. Austell, Cornwall, England, formerly a division of English China Clays, Ltd., to address more effective methods of moisture reduction of micron-size china clays. The Tube Press reduced moisture sufficiently to produce a hard surface-dry, handleable cake and clear filtrate discharge, which was recycled into the process. This development work was conducted using a 200 Series Tube Press (200 mm diameter x 2500 mm long filter surface)."

Jan 1, 1993

By E. J. Marcotte

"BRIEF DESCRIPTION OF GRINDING CIRCUITCrushed ore at -5/ 16 in. is delivered by a conveyor system from the crushing plant to two 1250 ton fine ore bins. The ore is transferred from each bin by a 30 in. feeder conveyor belt, operated by a Link Belt P.I. V. (variable speed) drive, to a 24 in. conveyor that feeds the 8 x 10 Allis Chalmers rod mill.The rod mill discharges to a common mill discharge pump box. Three 6 x 6 SRL pumps are employed to pump the combined mill discharge pulp to a common distributor box which distributes the feed to two of the three Kreb D lSB cyclones in each of the two banks at a hydraulic pressure of 6 psi.The cyclone overflow at a specific gravity of 1. 25 (i.e. 32% solids) is transferred by gravity to two revolving chip screens for wood chip removal and from there to a pump box. Two 5 x 5 SRL pumps feed the pulp to the thickeners. The underflow from the cyclones is fed to two 8 x 8 Allis Chalmers ball mills which discharge to the common mill discharge pump box. Thus, a closed circuit is formed between the ball mills and their respective bank of cyclones. The circulating load as most recently calculated is 262%."

Jan 1, 1966

By Bing Li, Kai Liu, Yongcheng. Zhao

With the ongoing development of copper smelting technology, the improvement of environmental emission control and achieving an automated continuous copper pyrometallurgical process have become the key development goals for copper smelting. The double bottom blowing continuous copper smelting process combine bottom blowing smelting (SKS) and bottom blowing converting (BCC) process and fire refining as “three-connected furnaces” arrangement is a pyrometallurgical process independently developed by China’s ENFI which can continuously produce copper from raw material through to anodes. This technology can improve energy efficiency and reduce environmental emissions for the overall copper smelting and converting process. This paper discusses the engineering characteristics and production practice of the SDIC Jincheng Metallurgical Project, which operates SKS smelting and BCC converting process with “three-connected furnace” arrangement for the first time in the world. Advanced engineering concepts and tools were used to optimize the configuration during the project engineering stage. The operation shows that the process has good environmental performance, reduced energy consumption and high level of automation, which is a new choice for copper continuous smelting process. INTRODUCTION One of the most important developing trends for the overall copper smelting process is to develop a continuous operation. Continuous copper smelting can maximise energy efficiency in copper concentrate and make full use of the rich heat treatment system. Cold charge and a part of low-heat-generating materials, which are processing with additional equipment in traditional copper smelting process, can be processed with rich reaction heat in continuous copper smelting and converting process to achieve good economic benefits. Yuan and Wang (2017) noted that SKS+BCC copper smelting process can reduce the secondary SO2 emissions compared with discontinuous copper smelting process, which required transportation of melted matte by matte ladle and may cause secondary pollution. The continuous copper smelting process can also reduce the generation of intermediate cold materials.

Jan 1, 2019

By Richard R. Klimpel

"This paper discusses the effect of water chemistry, reagent type, and other environmental factors on the performance of sulfide mineral size reduction and froth flotation processes. Two specific problems will be discussed: l.) the importance of appropriately utilizing the electrochemical window that is created in the grinding process to enhance sulfide mineral recovery by froth flotation; and 2) the impact of steel grinding media versus autogenous grinding on the efficiency of sulfide mineral flotation with varying thiol collectors and water sources.IntroductionThe mutual dependency between size reduction and mineral froth flotation is well recognized from the viewpoint of particle size and mineral liberation characteristics. The purpose of this paper is to discuss two less obvious industrial interactions between size reduction and froth flotation that have come up in the various plant optimization studies conducted by this author. These interactions are complex but appear to be important at the industrial level as plant throughput is directly affected, either positively or negatively by such interactions. Examples v.ill be given on how the method of grinding influences flotation and how different water sources influence the flotation behavior of electrochemically sensitive minerals. With each of these interactions, a number of fundamental research studies have shown previously that some effects can be measured under idealized and very small scale experiments. Such research studies will not be cataloged or exhaustingly reviewed in this paper. Whether these same types of effects can be measured in an industrial environment and are economically important is much less certain. This paper will present some rather unique experiences gained from larger scale test experiences which clearly indicate findings that plant operators should be aware of."

Jan 1, 1996

By George P. Demopoulos, Amani Al-Othman, Terry C. Cheng

One critical issue in chloride hydrometallurgy is the regeneration of the lixiviant HCl that is currently achieved by pyrohydrolysis. In this paper, a low temperature HCl regeneration process was investigated which regenerates HCl and produces saleable gypsum. This process promises to reduce the generation of wastes by the reaction of spent calcium chloride leach liquors with sulfuric acid solution at low temperature. Experiments were performed to determine the optimum conditions of the reaction in terms of temperature, reagent concentrations, rate of reagent addition, mixing and seeding/recycling to produce marketable gypsum and HCl with practical strength.

Jan 1, 2004

By Geoffrey C. Streeton

A continual objective of mine operations is to reduce ground control costs without compromising the overall safety or performance of the installed ground support. Any change in the ground support regime must not result in a less secure or safe workplace. The due diligence required to implement a change in rockbolting practice is extensive, particularly when the new bolting system has not been used at any other mining operation. Factors such as yield, shear strength and embedment strength must all be investigated to gain an understanding of how the rockbolt can be expected to perform. This paper also discusses the substantial cost reductions and efficiency gains which can be achieved through the introduction of the Jumbolt rockbolt.

May 1, 2001

In 2009 Newmont Mining Corporation?s annual global spend on grinding media reached $94M USD, having doubled in the five years since 2004. The major contributing factor to the spend escalation during this period was unit consumable price, with total media consumption also rising as a function of annual ore tonnes milled. In an effort to better understand and manage the growth of this expenditure a significant supply chain management program was implemented. This was complemented by a series of technical initiatives focussed on grinding media specifications, quality management and the prediction of grinding media wear rate as a function of physical ore characteristics. This paper discusses the methodology and outcomes of these activities.

Nov 1, 2011

By Bennett McLaughlin

The Penna Shaft is the deepest single?lift shaft in North America. AGNICO-EAGLE started sinking the Penna shaft in 1995 with a hoisting plant capable of hoisting 1 800 tonnes per day from a 2 240-metre deep shaft. Exploration success at depth lead to the replacement of the existing double drum hoist by another double drum hoist capable of hoisting 7 000 tonnes per day. The use of another double drum hoist, instead of a Blair Multi-Rope winder, to hoist 24,5-tonne skips was only made possible by lowering the safety factor. This paper describes recent experiences at Penna and in South Africa, and examines the possibility of extending the double drum hoisting system to a depth of three kilometres.

May 1, 2003

By Graham A. Davis

The definition of sustainable development is often taken from the so-called ?Brundtland? report, requiring that activities of the current generation not detract from the potential welfare of future generations. Mining is often held up as unsustainable in this regard since the extracted resource is nonrenewable. Yet Brundtland?s definition of sustainable development also requires that the current generation address the disparity in welfare across the globe, a facet of Brundtland?s report that most have ignored. This paper examines the impact of mining on the welfare of the poor. It finds that poverty levels in the poorest mining and oil intensive economies are lower than expected given these economies? geographical location and level of income, and that extractive activities are therefore completely consistent with sustainable development.

May 1, 2004