Search Documents

By M. K. Walter

"The underground operations of Kidd Creek Mines uses an average of 450 U.S. gpm water during regular operations, and discharges an average of 800 U.S. gpm through consecutive staged pumping lifts of 1200f t.Water is used as a flushing medium for the drilling operations and as a dust suppressant for drawpoint mucking. The water retains an average of 5% suspended solids by weight which is removed underground before being pumped to the surface. This paper outlines the treatment of the mine water for the removal of suspended solids which are chemically treated to settle out as a sludge product of 60% solids by weight. This process reduces the sludge handling operation by 50%. The sludge is systematically disposed into the ore passes.IntroductionThe Kidd Creek minesite, located 27 km north of Timmins, Ontario, produces 4.5 million tonne s of copper, lead, zinc and silver ores annually from its No. I and No.2 underground mining operations. Both mines use a sublevel blasthole stoping method of extraction.Water from the underground operation passes through a series of surface settling ponds, where it is treated to remove heavy metal ions from solution. A blend of the pond effluent with fresh water from Kidd Creek, supply the underground with water at an average rate of 450 U.S. gpm. Water flows from the production zones through coarse sumps and into a main pumping station. There are five main pumping stations underground, three in No. I Mine and two in the No.2 Mine.The No. 2 Mine pumping stations are located on the 4800 level and the 3600 level. All water below the 3600 level to the shaft bottom is controlled from the 4800 pumping station. The water from the 4800 pumping section is combined with water from the remaining levels of the No.2 Mine at the 3600 pumping station. Water from the 3600 pumping station is pumped to the 2400 pumping station in No. I Mine.The No. I Mine pumping stations are located on 2800, 2400, and 1200 levels. All water below the 2400 level to the shaft bottom is controlled through the 2800 pumping station. This water is pumped to the 2400 pumping station. The 2400 pumping station also controls the water below 1600level to 2400 level."

Jan 1, 1988

By Michele L. Kimble

A fast-flow reactor mass spectrometer has been utilized to investigate the reactions of gas-phase gold cluster anions with CO and oxygen. Addition of CO to Aun - produces species of the form Au(CO)m -, where m = 2-5. However, CO does not bind to Au2 - or Au3 -. With oxygen addition in the cluster source, gold oxide species with both molecular and atomized oxygen are produced. The addition of carbon monoxide to these preoxidized gold cluster anions reveals that select species with 1, 2, and 3 gold atoms participate in the oxidation reaction to produce CO2. Bimolecular rate constants for the reactions between these species and CO are also discussed.

Oct 1, 2003

By Rufus L. Chaney

A new technology is available to the Ni mining and remediation community to “phytomine” Ni from mineralized or contaminated soils using rare plants which hyperaccumulate Ni to over 1% of shoot dry matter. Research has identified useful plant species, and even bred improved cultivars of Alyssum murale and Alyssum corsicum for commercial phytomining in temperate regions. All agronomic practices (fertilization, soil amendments, planting and harvest methods) needed for economic phytomining were identified to attain high yields and high Ni concentration in the biomass. In tropical regions, other species are available such as Phyllanthus which accumulate over 1% Ni in dry shoots. These species are perennial so they regrow after annual cutting to harvest biomass. Expiration of our patents on the technology opens the opportunity for other organizations which control Ni rich natural soils or contaminated soils requiring remediation to commercialize the technologies. Inexpensive methods to remediate/revitalize Ni contaminated phytotoxic soils using agronomic approaches have also been developed and demonstrated at Port Colborne, Ontario, but adoption is delayed until formal agreements with government are completed. These new simple remediation and profitable phytomining technologies can obtain Ni from soils which contain Ni well below levels considered economic for current mining technologies, and the plants biopurify the Ni so it is easy to recover Ni metal from plant ash by pyrometallurgical or hydrometallurgical technologies. Although increasing pH decreases the solubility of Ni in all soils, raising pH increases Ni accumulation by Alyssum species. Hence usual chemical extraction methods for phytoavailable soil metals such as the DTPA- or NH4-OAc-extraction cannot predict Ni accumulation by Alyssum species.

Jan 1, 2016

By C. Zangerl, H. Lechner

"Large scale rock slides in deeply incised Alpine valleys are common hazards that can endanger human life, settlement areas and critical infrastructure such as highways, railways and reservoirs (Bonzanigo et al., 2007). In order to perform reliable forecasts of the behaviour of rock slides influenced by large dam reservoirs the geometry, the kinematics, the deformation behaviour and the hydrogeological situation need to be understood profoundly. Based on generic rock slide models the influence of the rock slide geometry on the stability as well as the impact of the buoyancy forces and water load of the reservoir at the toe of the slope are the main focus of this study. Various assumptions of hydraulic conductivity, groundwater conditions of the rock slide and impoundment depth of the reservoir are analysed using limit equilibrium approaches.Generally, deep seated rock slides are characterised by deformation along one or multiple shear zones where most of the measured total slope displacement localizes. Many large rock slides, especially those observed in foliated, mica-rich crystalline rock masses (e.g. paragneisses, mica schists, phyllites), do not fail suddenly or reach high velocities. Instead, many of them move slowly and reach velocities of centimetres per year or even less. Some show episodic accelerations, sometimes reaching alarming levels, but then subside to non-critical levels again. However, there is a potential that deep-seated rock slides fail rapidly, develop into far-reaching run-out rock flows, and cause catastrophic events. Whereas the role of triggers in promoting phases of acceleration is often understood, the same cannot be said regarding the kinematics and dynamic processes by which the rock slide mass decelerates, re-stabilises or accelerates to a catastrophic degree once the trigger impetus has been removed. Thus key questions of the presented work concern the geotechnical, geometrical and hydrogeological conditions under which a slowly moving rock slide is triggered to accelerate to irreversible, maybe dangerous velocities. The development of the sliding zone is generally influenced by pre-existing discontinuities such as brittle fault zones, shear and tensile fractures, foliation and bedding planes. These geological structures determine the geometry of the sliding zone which can either be rotational or translational. During the gravitationally induced failure process the geometry of the rock slide undergoes a change.Several observed post-failure geometries in metamorphic rocks show a concave topography in the middle to upper part of the rock slide and a typical convex or bulge-like topography at the toe of the slope (Zangerl et al., 2012). Whereas the sliding zone of the upper part of such a rock slide mass is rather steep and planar, the inclination of the sliding zone at the toe can be close to zero and act against the driving forces (Alonso et al., 2010). A shear zone that meets alluvial deposits at the foot of the slope encounters a stabilizing impact on the mechanical behaviour. This buttressing effect of alluvial sediments has a remarkable influence on the slope stability."

Jan 1, 2015

By H. R. Manouchehri

"It is well understood that, apart from particle hydrophobicity, the flotation process is strongly influenced by the cell hydrodynamics. Once the chemical conditions were optimized and fixed, the flotation rate is essentially determined by impeller speed and the air flow rate.The collection efficiency in flotation is a product of collision, attachment and stability/detachment efficiencies. The collision efficiency for a given particle diameter is increased by decreasing the bubble size and bubble velocity as well as increasing the power input to the cell. The attachment efficiency, however, is defined by bubble size and its velocity. The detachment/stability depends on the relative magnitudes of the attachment force between the bubble and particles and the detachment force acting on the bubble-particle aggregates. For the particles having specific contact angle, the stability decreases as the energy input increases. Therefore, there must be an optimum energy dissipation to maximize recover of defined size fraction.A comprehensive laboratory study was devoted to determine the effect of power input in recovery of finely grind Cu-Ni bearing ore. Several flotation tests were conducted to define the hydrodynamic parameters for a laboratory scale Runge cell under different impeller speeds. An increase in flotation recovery of finely ground ore was observed when the impeller speed was increased from 450 to 1,200 rpm. The experimental results have shown increasing in water recovery and improving in flotation kinetics of fines by increasing the power input to the flotation cell. Implementation of the Wark flotation model to the experimental data revealed a good correlation between the experimental data and the model. For the particles having enough hydrophobicity the flotation rate increases by increasing the impeller speed due to a higher value for collision efficiency within the cell."

Jan 1, 2016

By Gordon Thompson

"Development of the unique Mine Games exhibition at Science World British Columbia is the largest ever collaboration of many interests to present the story of mining and the issues of mineral development delivered to the public by a science education centre.IntroductionMineral education programs have long been a major focus of the British Columbia mining community. Mine Games and its tremendous potential to enhance industries image and the public's awareness of mining is unequalled in the field of Issue Based Education Exhibits.The main goal of the exhibition is to look at the future of resource industries in a rapidly changing world of economic activities, new technologies, and growing public concern for the environment. Three challenges were the aim of the exhibition: to increase participation, to serve as a tool to increase interest in science and technology, and to draw an increasing number of school students to the interests of geology and the earth sciences. Mine Games is to serve as a meeting place for discussion of issues and where reliable information can be shared and new ideas explored.The exhibition is designed to develop new approaches to hands on learning that encourages visitors to explore and generate discussion and thinking with respect to resource development activities.The role of author, beginning in 1993, was, with senior industry leaders, to coordinate the raising of $1.3 million to complete the funding of the $1.6 million project total. The second and most interesting challenge was to work with the many minds that were collaborating to create the exhibition and to assure that the facts and science were correct. This involved the coordination of ""expert groups"" that verified the science and technology and the issues that the creative design team at Science World planned to use in development of each exhibit module."

Jan 1, 1995

By DALE MacGREGOR, VERA TUREK

The Blue Mountain nepheline syenite deposit has been the subject of several detailed studies. It has been variously referred to as an intrusive stock, a metasomatic deposit, an intrusive sill and a metamorphic-metasomatic body. The body is divided into six mineralogical zones, the first five being based on the characterizing accessory mineral; muscovite, muscovitemagnetite, biotite-muscovite, biotite, hornblende and pink syenite. Mining currently takes place only in the biotite zone. Foliation is particularly prominent in the central (hornblende) zone and near the margins of the nepheline syenite. Majic bodies within the nepheline syenite may represent basic rocks that have been less altered by metasomatism, metamorphosed basic dykes or sloped blocks of metasediments. The most prominent structural features are the northeast-trending folds that have been modified by later north west-trending folds.

Jan 1, 1984

By Mike McKevitt

We are trying to promote a concept and a change in management?s approach to the iterative process of grade control. This is important as grade control must routinely try and achieve the long term objectives set by the mine plan ??BackgroundBackground ??Factors contributing to variation from planFactors plan ??Basis of OptimisationBasis Optimisation ??Ore Block Optimisation processOre process ??Operating mine examplesOperating examples ??Chain of Mining. ??Intention is to highlight the need for repeatable and consistent materialand material-type classification to remain consistent with the Life of Mine Plan ??We can drill another hole or reWe re-optimise a plan, but once excavated, the final decision has been made ??The grade control decision is the last decision made in the resource exploitation sequence.

May 1, 2009

By Sean Dessureault

Technological Revolution ?Information age ? brought about by: ?Low-cost processing, storage, information sharing ?Shared & integrated data ? Increasingly more sensors & data sources From data collection to data use ??Data mining??analyzing the huge volumes of data ?Key example used in MBAs: ?Wal-mart, Google Explosion of data, trickle of information ?Paralysis of action Outline Trying to provoke- What drives innovation now? ?Challenges in mining Data Action Approach ?Examples from research & consulting upon request Conclusions ?Unaddressed challenges (Research Opportunities)

May 1, 2006

By M. J. Lopatka

This paper presents the results of field test and theoretical analysis driving resistance articulated 4x4 tracked robot test-bed. Tests were made on four different grounds. Designated elastomeric tracks resistance coefficients are much higher than for steel tracks. This information was important for the proper estimation of energy consumption in the process of driving.

Aug 1, 2013

By K. Reinharter, J. Schmidl, D. Gregurek, A. Spanring

Copper smelting furnaces are typically lined with magnesia-chromite refractories, which are exposed to multiple and complex stresses. The selection of the processing route, furnace type and slag system will be dictated by the specific ore type available, this will determine the individual refractory wear. This paper evaluates the common refractory wear mechanisms as observed in the copper Peirce-Smith converter and in the copper anode furnace. The chemical factors include corrosion caused by fayalite type slag and sulfur supply, as well as, by Cu-oxide attack. Changes in the temperature during the furnace operation (thermal-shock) create stresses in the brick lining which can only be absorbed in limited extent. Mechanical factors include erosion, caused primarily by the movement of the metal bath, slag and charging material, as well as, stresses in the brickwork due to punching. Finally improper lining procedures can also effect the service life. All these wear parameters lead to severe degeneration of the brick microstructure and a decreased lining life. Therefore, a detailed investigation and understanding of the wear mechanisms through “post mortem studies” together with thermochemical calculations by FactSageTM software is an important prerequisite for the refractory producer. Based on these research results, combined with specific process knowledge, appropriate brick lining solutions for copper processing furnaces can be recommended. INTRODUCTION The refining of copper includes converting of matte or black copper into blister copper for final fire refining process in the anode section. Typically Peirce-Smith (PS) converters are in use. Other technologies include Hoboken Converter, TBRC but also Flash Converting Furnace and bath smelting furnaces (ISA, Ausmelt) (Davenport et al., 2002). For fire refining two types of furnaces are used – the rotary furnace type is dominantly used in the primary production route while secondary smelters tend to use hearth refining furnaces which are more suitable for scrap melting. Installed working linings are based on magnesia-chromite bricks but especially in the anode refining section the application of alumina-chromia bricks have become more popular in the recent years. It comes without saying that, to some extent, large variations in the slag composition can be observed from the data provided to RHI Magnesita during post-mortem studies of used refractory samples and this needs to be addressed properly during the selection process of refractory linings.77

Jan 1, 2019

By Walter Valery, Lauren Hafla, Megan Tibbals, Adrian Dance, Jeff Snyder

"Newmont Mining Corporation’s Carlin (“Carlin”) operation processes roaster feed through a double rotator, dry grinding mill following secondary crushing. Metso Process Technology & Innovation (“PTI”) was involved in a review of crushing and dry grinding circuit operations in August 2009. A number of opportunities for increased throughput were identified in the PTI study.Extended plant trials were conducted in July 2010 to provide justification for possible circuit modifications and if needed, additional equipment. The trials confirmed that a finer crusher product would reduce the build-up of material ahead of the coarse grinding chamber in the double-rotator. Also revealed were material transport and airflow restrictions in the dry grinding circuit that resulted in a high circulating load.The secondary crushing plant demonstrated it was capable of reducing the amount of +¾” material in the mill feed thus increasing dry grinding throughput. However, wet and sticky feed affected screening efficiency resulting in low utilisation of the existing crusher capacity. The open circuit configuration also made it difficult to control crushing circuit product size.For the dry grinding circuit, changes in grinding media size, transfer grate design and increased airflow were recommended to reduce circulating load issues and increase circuit capacity. This paper summarises the crushing and grinding circuit review, the extended site trials performed by PTI and the improvements in dry grinding operation that resulted from this study."

Jan 1, 2012

By G. D. Hibbard

New regions of material property space can be accessed by combining microstructural design at the nm-scale with architectural design at the µm- or mm-scale. In the first case, large strength increases associated with grain size reduction to below 50 nm have driven extensive research efforts into the development of nanocrystalline materials [e.g. 1-3]. For many potential structural applications, however, the density of a nanocrystalline material is just as important as its strength. In fact, reducing the density is more important than increasing the strength for certain weight specific materials performance indices, and it is especially critical for applying structural nanomaterials in the aerospace and automotive sectors. We have developed a new type of structural nanomaterial wherein the effective density of the parent metal is reduced by more than an order of magnitude by incorporating an internal periodic cellular architecture of open space. In one example a low density cellular nanocrystalline material was created by electroforming nanocrystalline Ni around a rapid-prototyped acrylic photopolymer microtruss, Figure 1 [4]. Microtruss materials have periodic cellular architectures that are specifically designed to undergo stretching-dominated deformation as opposed to the bending-dominated deformation in conventional open cell metal foams [5,6]. This new cellular nanocrystalline hybrid material combined the structural efficiency of microtruss architectures with the ultra-high strength that can be achieved by grain size reduction to the nm-scale. Although it played a critical role as a cathode support during the initial stages of nanocrystalline electrodeposition, the polymer core did not contribute significantly to the inelastic buckling resistance of the composite metal/polymer struts and it may therefore be desirable to remove it post deposition by means of chemical dissolution or thermal decomposition [4]. Nanocrystalline electrodeposition can also be used to reinforce conventional cellular metals (Figure 2), creating new types of cellular composites such as metal/metal microtruss hybrids [7-10] and metal/metal foam hybrids [11,12]. For example, nanocrystalline Ni-Fe alloy sleeve thicknesses of up to 400 µm were used to reinforce an aluminum alloy microtruss that had been fabricated using a stretch-bend approach; the nanocrystalline sleeves had the effect of increasing the microtruss strength by up to a factor of twelve and the specific strength by a factor of three [8]. Alternatively, much thinner sleeves can be electroplated to produce structural coatings. In one example, a nanocrystalline Ni coating was designed to provide both corrosion protection and inelastic buckling resistance [10]. Because the ultra-high strength material was optimally located at the furthest distance from the neutral bending axis, only a thin coating of 50 µm was needed to double the inelastic buckling resistance of the 1.13 mm x 0.63 mm cross-section plain carbon steel struts [10]. Overall, the mechanical performance increase that can be obtained through electrodeposition depends on a complex interaction between the starting cellular architecture and the nanocrystalline sleeves.

Jan 1, 2010

By A. Kishimoto, Yoshida Honmachi, T. Uda, Y. Taninouchi

Recycling of e-scrap is often performed by utilizing a pyrometallurgical Cu smelting process. Several valuable metals, including precious metals, can be efficiently recovered through the Cu smelting process. However, recovery of Sn is quite difficult because it is distributed in slag during the smelting process. Sn is used as solder and plating in electronic devices, and its recycling will be more important in the future. In light of this background, a pretreatment process that can extract Sn directly and selectively from e-scrap was developed in this study. The proposed Sn extraction process involves alkaline leaching using iodate ions, IO 3, as an oxidizing agent. We conducted leaching experiments for Sn, Sn-Ag-Cu alloy solder, and Cu, and the effective dissolution of Sn was confirmed. In principle, the electrodeposition of Sn from the leach solution and regeneration of IO3 are possible by a subsequent electrolysis process. The results obtained in this study suggest that the proposed leaching process can be an effective and useful pretreatment for Cu-smelting-based e-scrap recycling. INTRODUCTION Electronic scrap (e-scrap), including waste printed circuit boards (PCBs), is one of the fastest growing waste treatment streams in the global urban environment. E-scrap contains numerous valuable metallic elements, including Cu, Sn, and precious metals, in rich quantity. Furthermore, some metals and other materials contained in e- scrap are hazardous to human health and the environment when they are not properly managed. The recycling of e- scrap is therefore a major concern in terms of resource supply and waste treatment, and it has been performed by many companies using a variety of methods.

Jan 1, 2019

By J. C. Salas, A. Weishaupt, J. A. Guzman

The origins of the electrorefining process date back to 1869, when the first ER cathodes were produced at Pembrey, South Wales. By the time that Pembrey was closing, Chuquicamata tank house was under construction, initiating in 1915 a long history of electrolytic cathodes production. Initially electrowon cathodes and later electrorefined cathodes were produced. During the history of Chuquicamata tank house, there have been several challenges associated with the quality demanded for electrolytic copper. Among them, the transformation from electrowinning to electrorefining in 1952, the onset of the direct commercialization of ER cathodes and the phase out of wire bars in the 80s, several technological changes including the implementation of permanent cathodes, and certainly the constant increase in complexity of the anodes refined. This paper explores the manner in which Chuquicamata has addressed these challenges and examines its links to process characteristics, which have been necessary to maintain a product quality according to market requirements and a brand, “CCC”, that is widely recognized worldwide. INTRODUCTION Located in the north of Chile, in the Atacama Desert, Chuquicamata is an open pit copper mine that for many years has played a relevant role in the global and local mining industry. Known from prehispanic times, the Chuquicamata deposit was initially developed between 1912 and 1915 by the Chile Exploration Company, the operating company of the Chile Copper Company controlled by the Guggenheim Brothers in the USA (Yeatman, 1916). Officially inaugurated on May 18th, 1915, by the President of Chile who pressed a button in Santiago sending a telegraph signal to the power generation plant specially built in Tocopilla, 1500 km north. It signaled the beginning of generating energy, sending it to Chuquicamata, another 140 km east (“El mineral de Chuquicamata”, 1915), marking the beginning of its industrial operation.

Jan 1, 2019

By Kevin Azocar, Jim Hazzard

"Slope stability analysis is performed most commonly using limit equilibrium calculations or numerical models assuming a two-dimensional slice through an infinitely long slope surface. In areas such as open pit mining, where most slope surfaces are not planar, the importance of curvature becomes important due to the economic gains associated with creating a steeper slope. With advances in computing capabilities within the last decade, three-dimensional slope analysis can be performed within reasonable time frames. Some work has been done on the potential importance of curvature on slope stability, mainly assuming homogenous materials with a circular shear-failure mechanism. However, many open pit mines are excavated in jointed rock mass where a completely different set of failure mechanisms can be seen. Depending on the geometry and radius of the pit, the curved geometry may influence the factor of safety and failure behaviour compared to a two-dimensional slice.A series of numerical analyses were performed to investigate the effect of curvature on jointed rock slope stability compared to an equivalent two-dimensional slope analysis. By using discrete element method models, the influence of joint planes and interaction between distinct blocks can be seen. With a three-dimensional model, the effect of curvature can be combined with multiple joint sets at any orientation, which cannot be seen in a single slice. Numerous three-dimensional models are created, along with an equivalent unit-thick slice. The effect of curvature on a variety of different types of failure mechanisms is observed, and graphical relationships are created to quantify the difference between the three-dimensional factor of safety and the two-dimensional factor of safety based on the degree of curvature."

Jan 1, 2015

By C. B. Mapes, E. C. Dowling Jr.

"To reduce concentrate dewatering and drying costs, the Concentrator Division at Phelps Dodge Morenci, Inc. investigated available filtration technologies. Numerous methods were explored, including: drum, disk, belt, pressure, hyperbaric, and ceramic media filtration. An economic evaluation of the individual filtration technologies indicated the advantages of ceramic media filtration for Morenci concentrates. This paper discusses the technological development culminating in the first full scale application of ceramic media disk filters in North America. Low moisture contents are obtained at high production rates and greatly reduced operating costs.INTRODUCTIONPhelps Dodge commissioned the Morenci Concentrator Filter Plant in 1942 with four 8'6"" Dorr-Oliver cloth disk filters. That year, the filter plant processed 265,537 tons of concentrate grading 20.5% Cu. The filter cake production averaged 9.3% moisture. In 1944, the Extension Filter Plant commenced operation with three additional 8'6"" Dorr-Oliver cloth disk filters. This coincided with the expansion of the concentrator. Production that year totaled 451,567 tons of concentrate grading 23.8% Cu. Moisture averaged 9.4%.Through the years additional filter units have been added in response to increased concentrate production. An Eimco drum filter was installed on the extension side and an additional Dorr-Oliver disk filter was installed on the original side in the 1950's. In 1961, two 8'6"" Peterson disk filters were installed, one on each side to replace two worn-out DorrOlivers. The installation of four 10xl2 foot Peterson drum filters was completed in 1974, coinciding with the Metcalf Concentrator startup. An Eimco belt filter was installed later.The greatest change to concentrate dewatering at Morenci occurred in 1963 with the addition of a 10x60 foot rotary gas fired dryer. The installation also included a number of conveyors to deliver filter cake from both plants to and from the dryers. Other ancillary systems included dust scrubbers and their slurry pumps. The commencement of drying was undertaken due to the rapid increase in cake moisture as a result of the LPF process and the recycling of acid plant scrubber dust slurry from the smelter. In 1972, a second dryer system was installed to increase capacity."

Jan 1, 1993

By R. Gordon, J. Palich, W. Qian

The EarthProbe DCIP system deploys tightly spaced electrodes connected to a centralized data acquisition system that enables arbitrary selection of current and potential electrodes through relays. Rapid data collection (approximately 1000 readings per hour) and advanced signal processing allow for efficient use of conventional and novel arrays and the removal of natural and cultural noise. What is unique about the system is its electrode and borehole cable design, which allows seamless integration of borehole and surface measurements. EarthProbe operates in four configurations - surface, borehole, borehole-to-borehole, and surface-to-borehole (a variant of the borehole-to-borehole configuration).

Jan 1, 2011

By Yasser Mohamed

Daily field management of earthmoving operations requires quick and regular decisions for allocating available equipment to different jobs on a project. A general foreman?s day starts with matching several activities with a suitable set of available equipment to achieve the highest productivity and lowest unit cost. Usually, this decision-making process needs to be quick, and depends to a great extent on the foreman?s experience, which varies from one individual to another. Many analytical solutions with various degrees of sophistication and optimization exist to address such decisions. However, adopting any of these solutions is contingent on how accessible and easy-to-use the solution is. This paper discusses the development process of a webaccessible solution for evaluating earthmoving fleet composition and allocation scenarios. The solution relies on discrete event simulation and an optimization backend engine, but introduces the user with a simplified and easy-to-use interface that is accessible from any mobile device, and is customized to specific user?s needs. The developed system gathers most equipment and site-related input data from a company?s information systems to minimize user input. The user mainly needs to formulate equipment and job combinations and allocation scenarios (e.g. soil type, quantity, and hauling distance), according to equipment availability each day. Then the system will evaluate the productivity and unit cost estimates for each scenario, allowing the user to choose the most suitable one. It may also be used to automatically recommend the optimum solution given an available list of equipment. The paper presents the process followed in prototyping the proposed system in collaboration with a major Canadian earthmoving contractor, and customizing it to the user needs within the company. It also describes the overall structure of the developed system and its core simulation model.

Aug 1, 2013

By Richard R. Klimpel, Simon Isherwood

"The industrial processing of ores containing gold and/or platinum minerals is generally mining site specific, e.g. McQuiston and Shoemaker (1985). The variety of various mineral processing techniques employed is extensive and includes size classification, gravity concentration, amalgamation, roasting, cyanidation, chemical leaching, ion ex-change/solvent extraction and froth flotation. Because of the relatively small quantities of Au and Pt that exist in the earth’ s crust, the economical recovery of Pt and Au often requires that the Au and Pt be associated with other industrially important minerals. This association of Au and Pt with other minerals can occur in very complicated mineralogical forms. It is probably safe to say that Au and Pt mineral concentration from natural ores represents some of the most complex metallurgical challenges facing the mining industry.Froth flotation is a technique that is receiving increasing industrial attention for the treatment of finely disseminated and/or associated Au and Pt minerals. The high throughput at relatively low capital cost, the potentially high selectivity, and the existence of a well-established technology for treating more abundant associated minerals such as base metal sulfides makes froth flotation an attractive processing alternative. Broadly speaking, the industrial oriented froth flotation experience with Au and Pt minerals exists in two major categories: 1) the flotation of Au and Pt associated with pyrite (or pyrrhotite) and 2) the flotation of Au and Pt associated with primarily Cu, Zn, or Cu/Pb/Zn containing sulfide ores.In the case of the precious metal association with pyrite (or pyrrhotite), much of the published froth flotation experience comes from South Africa. Typically, such processes are done using an acid side flotation with a collector such as mercaptobenzothiazole. The approach obviously is to float pyrite and hence recover associated gold. Generally the higher the total sulfur recovery the higher the gold recovery. Similar experiences of Pt associated with pyrite are a lot less common mineralogically and hence less well documented industrially. For example, in Canada, Pt is often associated with pyrrhotite but is not really processed as a straight pyrrhotite recovery.For the situation of Au and/or Pt associated with other base metal sulfide minerals, the industrial experience base is quite varied and is well documented from both North and South American operations. The nature of most of these flotation processes is to design, operate, and optimize the installed concentrator to get the Cu, Pb, Zn, Ni, etc. that is the bulk of the valuable sulfide ore and then take whatever precious metal recovery comes. Typically, such flotations are on the basic side using standard thiol collectors such as xanthates, dithiophosphates, thionocarbamates, etc. It is very common with such ores to use mixtures of collectors in order to get ""everything"". Often in such plants, there is an inherent balancing act occuring so as to operate in such a manner to reject pyrite (and pyrrhotite) in order to maintain high base metal mineral concentrate grades and yet recover sufficient precious metals such as Au and Pt minerals which often are associated with the iron sulfides being rejected. Obviously in such an environment, the smelter operation often ends up telling the concentrator what the precious metal recovery actually was in a given production period."

Jan 1, 1994