Search Documents

By K. J. Brouwer, J. P. Haile

"Construction of the first stage of the tailings disposal facility for the Montana Tunnels Project was completed in October 1986. The project is located 37 km south of Helena, Montana, and involves mining of42 million tons of weathered diatreme are at a rate or 13 500 tpd to produce a gold/silver dore, as well as lead and zinc concentrates. The tailings disposal facility for the project includes a fully drained tailings impoundment for storage of the tailings solids, and a process waterpond for storage of all decanted water prior to recyling to the mill. The over-all facility is designed to achieve the basic objectives ofminimizing seepage to the environment in the short- and longterm, and achieving a fully drained stable tailings mass suitable for immediate reclamation on completion of mining. Specific features of the design include a soil bentonite seal and drainage system within the tailings basin, a free draining embankment with a design flow-through capacity of 4000 US gpm and an ultimate height of 230 ft (70 m), and a soil bentonite lined make-up water pond with a capacity of 420 acre-feet (530 000 m'). The tailings will be discharged in a rotational sequence through multiple spigot offtakes to achieve a thin-layer low energy laminar flow. This 'sub-aerial' deposition results in higher stored densities and maximizes liquid-solid separation on the tailings beaches. The over-all design played a major role in the successful permitting of the project, and was significantly cheaper than a conventional wet disposal system, with overall unit costs for tailings disposal of less than US$0.36 per ton.This paper outlines the site characteristics and the tailings material properties and their influence on the design. Extensive use was made of naturally occurring free draining materials as well as bentonite modified soil liners within the tailings basin, embankment and retention ponds. General construction procedures for the various components are described, as well as on-going construction requirements utilizing materials from the open pit. Finally, the over-all costs and unit costs for tailings disposal are presented."

Jan 1, 1988

By S. Dallaire

"RÉSUMÉLes revêtements céramiques ont une moins grande visibilité que les revêtements métallurgiques. Ils ont cependant jour un role significatif dans noire développement technologique. Les procédés de revêtement ont permis de s'affranchir de barrières technologiques importantes dans le domaine de l'optique, de l'électronique, de l'usure, des hautes temperatures. L'introduction de nouvelles technologies ou la mise en service de nouveaux matériaux peut nécessiter l'adaptation de certain procédés actuels ou le recours a des procédés qui ont peu percé jusqu’ à maintenant.ABSTRACTApplications concerned with ceramic coatings are not as well known as those with metallic coatings. However, ceramic coatings have played a tremendous role in the development of technology. Ceramic coating processes made it possible to overcome technological barriers in the areas of optics, electronics, wear resistance and high temperature applications. Ceramic coatings can provide new properties to materials never considered for demanding applications. They can also open new frontiers and revitalize materials which are maturing or in decline."

Jan 1, 1990

By Troy Boisjoli

Since its discovery in February 2014, the Arrow Uranium Deposit has undergone rapid development through aggressive and systematic drilling programs and is now being progressed through advanced engineering and permitting. Based on the 2018 NI 43-101 Technical Report, the Probable Mineral Reserve estimate totals 234.1 million (“M”) pounds (“lbs”) triuranium octoxide (“U3O8”), contained in 3.43 M tonnes at an average grade of 3.09% U3O8. The proposed processing plant at the Rook I Project (the “Project”) will be capable of producing up to 31 M lbs of U3O8 per year, with a projected mine life of nine years based on the Probable Mineral Reserve estimate, although NexGen is permitting a 24-year operating life at the Project assuming the majority of Inferred Mineral Resources are upgraded to Indicated Mineral Resources with continued mineral resource development drilling. The Project will be developed through transverse and longitudinal longhole mining methods, pairing primary and secondary stoping techniques with a high degree of equipment mechanization which will provide a combination of good productivity, high extraction, and stable back support. This next generation of uranium operations combines the use of advanced tele-remote equipment and instrumentation with a low-cost bulk mining method and a best-in-class tailings management practice, effectively reducing operating costs and setting a new standard for elite environmental and social practices.

Jan 1, 2020

By H. Clare Horwood

"Three types of structures, the main shear zone, the north shear zone, and a series of hanging-wall fractures, contain all the orebodies so far discovered at the McKenzie Red Lake mine. Lenses and veins of quartz in these zones and fractures are the sources of the ore. The ore-bearing structures are unusual in that they are in a complex intrusive mass known as the McKenzie-Gold Eagle stock. They are believed to have been produced by compressive stresses from the south andsouthwest.The mine is on the northeast side of McKenzie island, in Dome township in the central part of the Red Lake area. The original discovery, the main shear zone, was made in 1928, about 3 years after the property was staked, by M. L. Bouzan who was in charge of prospecting and development work on the property. Subsequent diamond drilling and underground exploration led to the installation of a mill, which came into production early in 1935. The hanging-wall fractures were found branching out from the main shear zone during development work on the 350-foot level. The north shear zone was discovered in 1940.From 1935 when the mill began operation until the end of 1946 total production from the mine was approximately 269,349 oz. gold and 69,317 oz. silver, having a value of $9,679,739, recovered from 823,527 tons of ore.GENERAL GEOLOGYThe McKenzie-Gold Eagle stock has a total length of approximately 1 ½ miles and a width of about ½ mile. It was intruded into a complex synclinal fold in Timiskaming sediments. The sediments, which have been cut in only one place in the underground workings, are principally wellbedded greywackes. The stock is composed of large masses of diorite and granodiorite, a small mass of hornblende pyroxenite, and basic dykes of two ages. The diorite occurs as irregular masses in large measure surrounded by the granodiorite that it intrudes. It contains tabular crystals of andesine, having a maximum length of3/4 inch. The hornblende pyroxenite is an elongated lens or dyke in the diorite. The granodiorite masses occupy about two-thirds of the stock. Along its eastern side the main mass tends to become darker and more dioritic toward the diorite contact.Basic dykes of pre-vein and post-vein age are the youngest intrusive rocks at the mine."

Jan 1, 1954

By Stavros A. Argyropoulos, Radhakrishna Valiveti, Bernard Closset

"The use of microprocessors in metallurgy is currently increasing at a very fast rate. A large number of companies are offering systems ""off the shelf"" which are aimed at the data acquisition and process control market. There are two main drawbacks to these systems: first, they are usually quite expensive, and second, they are not completely compatible with the target metallurgical application. An alternative is to develop a microcomputer-based system "" in lab "".A dedicated microcomputer system has proved to be very useful in many metallurgical research applications(1,2)). However, in this system the analog input signals had to be transferred over long distances , and significant noise was introduced despite the use of shielded cables. In order to overcome this problem a network of low pass-filter s was designed and built. The usage of the abovementioned system brought the need to digitize the analog signals in-situ and transfer the digital signals, which are much less susceptible to noise over very long distances. This distinctly different design philosophy has become a reality with the evolution of microprocessor technology over the last few years. This design philosophy is utilized in this development."

Jan 1, 1984

By R. B. Taylor

"The Delnite mine is in the northwest part of Deloro township, Cochrane district. The property consists of 307 acres on the so-called 'South Break' in the Porcupine camp. The Company was formed in 1934 to take over the holdings of La Roche Mines, Limited. Gold has been produced continuously since June 1, 1937. The value of the gold recovered to date (December 31, 1946) has been $7,456,000, and the average grade of ore $6.81 a con.The ore at the Delnite occurs in relatively narrow, persistent, quartz-ankerite veins, which generally contain tourmaline and have a ladder-like structure. The gold occurs in the free state, and in association with pyrite and arsenopyrite, the two chief sulphides. The host rock is fine-grained, highly carbonatized andesite of Keewatin age."

Jan 1, 1954

By John F. Gartner

"New terrain maps provide information on the ground conditions in northern Ontario. This information has a relevance to mineral exploration because it assists the user in determining ground conditions prior to entering the area. The prospector, geologist, geophysicist and geochemist can then plan for the optimum use of exploration techniques best suited for theseground conditions.These terrain maps are the result of the Northern Ontario Engineering Geology Terrain Study-a program carried out by five consultants under contract to the Ontario Geological Survey of the Ministry of Natural Resources. The area mapped is 370,000 km2 and more than 100 basic data maps at a1:100,000 scale will be published.An unique terrain legend was derived to facilitate the mapping and it allows the derivation of specific user information. Examples of some of these uses are described. Introduction""Where did all the boulders come from Charlie?"", asked the student, as the prospector and his young assistant clambered through the bush. "" Why son, they were brought down here by the glacier"", the prospector replied. ""But where is the glacier now Charlie? "", persisted the young man. ""Gone back up north for more boulders son!""An old story, but one that illustrates the importance of overburden to the prospector. The use of overburden as a prospecting technique is not new. In fact, the principles have been known in the western world for at least 235 years (Shilts 1976). More recently, Dreimanis's classic work on boulder tracing (1957) and Lee's work (1971) emphasize the role of glacial geology in prospecting. In addition, papers by Smee and Sinha (1979), Averill (1978), Bereton (1978), and Gleeson and Hornbrook (1974) all describe the importance of drift in mineral exploration programs. The discovery of the copper deposit in the northern Ontario township of Currie (Thompson, 1979) is attributed in part to till prospecting methods. So the significance of the overburden is firmly established, both in the literature and in the minds of today's prospectors, geologists, geophysicists and geochemists."

Jan 1, 1981

By M. M. Papic, J. C. Whitehead

"A sample of Hat Creek coal has been extracted using supercritical aromatic solvents in a laboratory-scale extraction unit. Extract yields in the range 21 to 27 per cent of dry-ash-free coal were obtained.These yields are significantly lower than yields available from high-volatile bituminous coal and some lignites. Thus in a combined extraction/hydrocracking scheme for the production of liquid fuels from Hat Creek coal the char product would exceed that required to supply the energy and hydrogen requirements of the process. Excess char could be used for the production of power or gas for sale.IntroductionThe Supercritical Gas Extraction (SGE) process developed by the U.K. National Coal Board operates in two stages: an extraction stage in which a coal extract is separated from mineral matter and undissolved coal and a subsequent hydrogenation stage.The SGE process is based on the ability of a compressed supercritical fluid to dissolve relatively high molecular weight substrates. It is operated under conditions where a hydrogenrich portion of the coal is selectively extracted in a short residence time extraction stage leaving a hydrogen-deficient char. The process schematic shown in Figure I illustrates that the extract produced is separated from the solvent and passed to a conventional hydroprocessing stage while the char product is utilized in the production of heat, power and hydrogen for the process. An extract yield in the order of 50 per cent dry-ash- free coal represents a ""balanced"" case for such a process in which there is just sufficient char for the provision of these commodities."

Jan 1, 1985

By R. Frank Chiappetta, E. B. Wilson

"The maintenance records for AL-60 airlegs at Falconbridge Ltd. are used to demonstrate some of the procedures for the analysis of such data.The data are not representative of pure failure s of one type or another. In fact, the records are for the undefined pseudo-failures which are usually found in industrial operations. However, because the machines are brought to the shop only when inoperative, the individual recorded components are treated as failures. Manual calculations are conducted to show the analysis of variance (ANO VA) approach to determine whether certain data can be combined; only a limited number of the 206 machines being considered. The manual procedures continue with the weighting of the suspensions; i.e. terminations f or reasons other than the failure of the given component. After the data are sequenced in the proper order, the nature or pattern of the data is determined using the Kolmogorov-Smirnov (KS) test.It is recognized that these manual examples must be replaced by compute r methods 10 process voluminous data of this nature. Such programs are developed and available. However, a program called RELCODE is used in this case to correspond to the manual examples and to take into account the suspensions. These analytical procedures form the basis for those studies required for good maintenance management."

Jan 1, 1985

By F. J. Munn

"Since 1976, Cardinal River Coal s Ltd. has completed mining in eight pits. In each of these pits, at least one wall has failed, none by design, although not totally unexpected, yet there was no loss of production nor risk to personnel or equipment. Cardinal River Coals Ltd. has been successful in implementing a program to cope with failures and now feels justified in adopting more optimistic design parameters.The wall control program at Cardinal River Coals Ltd. is based on the premise that the walls are going to fail, monitoring is to confirm when. The program consists of monitoring slope movements and piezometric levels as well as structural mapping and visual inspections. In case of excessive movement, the frequency and intensity of the monitoring is increased. If a failure is impending, suitable remedial action is undertaken such as cutting down the crest, building up the toe, depressurization of the wall, artificial support, or a combination of the above. If remedial action is not possible, monitoring permits operations to continue up to near the time of failure.At the design stage, the emphasis is on identifying the potential failure mechanisms and the con sequences of failure. Once the potential failure mechanisms are identified, a monitoring system can usually be employed to give sufficient response time, and providing the consequence of failure is not severe and/ or remedial action can be taken to arrest the movements, then it is practical to mine pit slope s which have a higher probability of failure."

Jan 1, 1985

By K. K. Feng

"Spontaneous combustion has always been a problem in coal mines and is identified mainly with the mining of low-rank coals. The liability of coals to spontaneous heating is only one of the factors in determining whether spontaneous combustion will occur. However, knowledge of the relative oxidizability of the coal is a useful factor to take into consideration when selecting new coal seams and mining methods for future mine development.Four methods (static isothermal, ignitability, adiabatic and dynamic) have been used to compare the relative liability of Canadian coal to spontaneous combustion and to investigate the mechanism of spontaneous combustion of these coals. Among these f our methods, the static isothermal method is considered to be the best indicator of the susceptibility of various coals to spontaneous combustion. Western mountain coal adsorbs more oxygen and has a higher tendency to undergo spontaneous combustion than the Harbour seam coal of Nova Scotia. It has also been observed that a higher methane content in coal will indicate a lower liability to spontaneous heating."

Jan 1, 1985

"In the past year, mining at the Doyon Mine has shifted entirely from open pit to underground. The mine produced 234 692 ounces of gold in 1989 and is expected to produce 225000 ounces in 1990. The Doyon Mill has been running slightly above design capacity, and recovery has increased 3%.IntroductionThe Doyon Mine is located 25 miles east of Rouyn-Noranda, Quebec (Figure I).It is a joint venture owned by Lac Minerals and Cambior, with each holding a 50% interest. Lac Minerals operates the mine under the direction of a management committee.Production at the Doyon Mine began in 1980 with the start up of the Main Zone pit. Shortly thereafter the Doyon Mine became the largest open pit gold producer in Canada.In 1983, a ramp leading to the fourth level and exploration drifts were driven. Results were very encouraging, therefore the decision was made to sink a 2150-foot deep shaft, which was completed in 1986.In mid-1986, production began in the West pit, while underground mining of the West Zone started shortly thereafter, at the end of the same year.In 1987 the mill capacity was increased to 3300 tons per day and the Main Zone underground operations commenced."

Jan 1, 1990

By R. L. Guerguerian, Eugene Bercel

"Grinding mill hydrostatic trunnion bearings require an external pumping source to provide and maintain the oil film between the bearing members. In order to guarantee a predetermined minimum film thickness, the lubrication system tends to be oversized. The oil film is ""indirectly"" controlled by flow, pressure and temperature monitors with fixed settings on the conservative side. This can lead to excessive maintenance and abbreviated life for the lubrication system components. A reliable method of monitoring actual film thickness would not only provide greater mill availability, but also minimize maintenance costs.This paper describes the instrumentation installed in Dominion hydrostatic bearings, and presents results of field tests where the output of that instrumentation was recorded under various operating conditions.IntroductionThe trend toward larger and more sophisticated grinding mills has made the operators of these machines increasingly vulnerable to financial loss, as the cost of downtime and repairs has increased directly with machine size. In order to guard against such losses, it is becoming imperative that large, sophisticated grinding mills be equipped with protective instrumentation to monitor some of the critical operating parameters and to identify events and trends which, if they go unnoticed, can lead to excessive maintenance costs and machine downtime. The idea of protective monitoring systems is not new. The operators of certain types of machinery where a high degree of safety is required or where machinery health can deteriorate very rapidly, as in the case of high-speed turbo-machinery, have long been using protective instrumentation on their machines. The increased awareness of the benefits of monitoring machinery conditions and the availability of reliable and relatively low-cost instrumentation of a large range of sophistication is making the practice now widespread. Traditionally, grinding mills have not been considered as high-risk machinery requiring instrumented protection. However, the trend, mentioned earlier, toward employing fewer, but larger capacity, mills increases the risk of significant disruption of production, and therefore measures to minimize the risks are desirable."

Jan 1, 1981

By T. Patching

"MINING operations at the Star Key Mine provided an example of a small-scale prairie-type coal mine that employed several interesting procedures and achieved good productivity with low capital expenditures. The mine was located about 11 miles north of the city of Edmonton, on the north side of the Sturgeon River valley. It opened in 1945 and operated until 1979. Output in the winters reached about 500 tons a day in the late 1940s, but in the spring and summer periods activity was usually limited to only servicing and development work. In the later years of the mine's life sales fell to less than 100 tons per day. Most of its output was bought for domestic use in furnaces and stoves so production of large sizes was desired. A modest market for stoker coal did exist for a time. Screenings (-5 / 8 in.) were sold to the city's power plant until it converted to natural gas and were also used for thawing frozen ground for work on pipelines. These markets were comparatively small and the small sizes did not command as high a price as did the larger sizes. However the extension of natural gas services to rural markets cut into the domestic heating market and finally led to closure of the mine. The coal was strong when freshly mined, but because of its high inherent moisture content, about 25%, it did not store well on surface but tended to disintegrate. It was of subbituminous Crank with a heating value of about 8000 Btu per pound and burned with a clean flame. The seam mined was in the Edmonton Formation, of Upper Cretaceous age, at a depth of 60 to 80 ft below the surface. The seam in the mine area was about 11 feet in thickness but thinned gradually to the north and south and split to the west (1). It was approximately horizontal but gentle rolls in the floor of several feet in height necessitated brushing in places to produce suitable haulage grades. The floor material was of bone and clay, overlying a thin layer of coal. Above the seam there were only a few feet of mudstones and weak sandy shales while the remainder of the overburden was clay and unconsolidated glacial till and surface soil. Because of the soft floor and weak roof material the miners usually left about a foot of coal in the floor to provide a firm working surface and about a foot of coal above the rooms and two feet of coal above the entries to provide a competent roof."

Jan 1, 1985

By Doug Barnstable

"Quinsam Coal Ltd. is assessing the potential of developing a thermal coal deposit near Middle Quinsam Lake on Vancouver Island. The coal reserve outlined is classified as a high-volatile, bituminous ""A” steam coal and is composed off our separate seams of varying quality within the Late Cretaceous Comox Formation.Open-pit mining methods will utilize a walking dragline and a truck / shovel module as the primary stripping tools. Following washing and mechanical drying in a Baum jig preparation plant, the coal will be transported to the proposed dock at Campbell River for shipment via 55, OOO-DWT vessels to world markets. The paper will outline the development and status of the project to date. IntroductionQuinsam Coal Ltd. is a joint venture of Weld wood of Canada Ltd. and Luscar Ltd . The participants propose to develop a thermal coal mine in the Middle Quinsam Lake area, 17 miles inland from Campbell River on Vancouver Island (Fig. I). By acquiring all the assets of Canadian Collieries in 1962, Weldwood also came to own the coal rights of the area proposed for development. Luscar Ltd . ha s been designated as project manager until completion of construction and thereafter will act as operator of the mine.Surface mining methods will be used to produce approximately 1.0 million short tons of coal annually from the Quinsam property. Seven separate mining pit s will be developed along with the supporting minesite facilities, including a proper paration plant. Transportation routing to Campbell River and the establishment of docking facilities will be required. The initial economic life of the mine is 12 years, with the provision to extend this in the future by developing higher-ratio, auger or underground reserves."

Jan 1, 1980

By Mark W. Masson, David B. Stevenson, David W. Broughton, Douglas R. Cruji, Steven E. Parry

"The Amalgamated Kirkland gold deposit is located at Kirkland Lake, Ontario, within the Archean Abitibi Greenstone belt of the Canadian Shield. It lies on a fault or “break”, termed the Cyprus Break, which is a splay off a regional structure termed the Cyprus-Battle Mountain Break. The Cyprus Break merges with the Cyprus – Battle Mountain Break above the -250 m level, as it was not encountered in shallow drilling or surface exploration. These structures lie 1.5 km south of the 727 000 kg (23 million ounce) Kirkland Lake Main Break and 0.5 km north of the 872 000 kg(30 million ounce) Larder Lake Break.The deposit is hosted by alkalic Timiskaming Group volcanic and sedimentary rocks which are overthrust by older Larder Lake Group tholeiitic and komatiitic fows along the Larder Lake Break. Timiskaming syenitic intrusives, similar to the host rocks for the Kirkland Lake Main Break gold deposit, intrude both suites.The Amalgamated Kirkland deposit consists of lode-style gold mineralization which is mainly hosted by altered and pyritized Timiskaming trachytic volcanics which wedge out or thin at depth, between two sedimentary units. The intersection of the Cyprus – Battle Mountain and Cyprus Breaks, in conjunction with the westward plunge of the volcanic wedge, appears to control the westerly plunge of the Amalgamated Kirkland deposit at approximately 50º.Mineralization is characterized by blue-gray brecciated and “wormy” quartz-ankerite veinswhich contain up to 10% fne-grained pyrite and, in decreasing order of abundance, minor galena,chalcopyrite, sphalerite, molybdenite and visible gold. The sulfdes and gold commonly occur alongfractures and wallrock inclusions within the veins. Native gold occurs as fne pinpoints distributed in 1-mm to 5-mm size clusters of up to ten or more grains.The auriferous veins occur within a quartz-ankerite-sericite-pyrite alteration assemblage which is enveloped by a broader zone of ankerite-sericite±hematite±quartz-pyrite alteration up to 60 m wide. This latter assemblage overprints the regional greenschist-facies chlorite-calcite assemblage.The Amalgamated Kirkland property has had a long history of exploration activity beginning with the first discovery of mineralization in 1911 on the Hunton Shaft claim located in the northeast corner of the property. Since that time various prospecting, mapping, trenching, geophysical surveys and diamond drilling programs have concentrated on either carbonate zones along the Larder Lake Break or quartz veins along the northern side of the property in association with complex trachyte flows and syenite dikes.Battle Mountain Canada Inc. located the Cyprus – Battle Mountain Break through a prospecting, trenching and geophysical program in 1989. Drilling by Battle Mountain and Cyprus Canada under the surface showing, coupled with several revisions to the structural interpretation of the Cyprus –Battle Mountain and Cyprus Breaks, resulted in delineation of the Amalgamated Kirkland deposit. Location of an auriferous structure through basic surface exploration within 1 km of a world-class orebody demonstrates both the subtle nature of Archean gold deposits and the potential for finding new mineralization in heavily prospected camps."

Jan 1, 1995

By T. Boiselle, C. Gielen, P. Henry, J. M. Bier

"Hydrometal is specialized in the production of zinc sulphate from complex secondary raw materials. Electric Arc Furnace (EAF) dust is one of the more interesting potential sources to produce zinc sulphate. In order to minimize waste quantities generated from EAF dust treatment, our R&D team has developed and patented a new process to recover the Fe contained in the dust as iron oxide product to be used and sold into the pigment market. The process is based on a specific reductive leaching step of the zinc ferrite contained in EAF dust, followed by a purification step to remove impurities (Ni, Cr, Cu...) and finally the controlled precipitation of the iron oxide. The aim of the iron precipitation step is to obtain the right shape and length of crystals in order to guarantee the right color and tinting strength of the pigment. The innovative aspects of the process results in the controlled oxidation of the iron to get the right crystal size and good purity material. The iron product can be valorized as red or yellow pigment often produced by the Penniman-Zoph process.INTRODUCTION A Few Words about HYDROMETAL Hydrometal SA (Engis, Belgium) is a subsidiary of Jean Goldschmidt International SA (JGI) in Brussels. JGI is mainly involved in metal trading activities (Goldschmidt, 1995). In 1985, JGI acquired the leaching circuit of a Belgian electrolytic zinc producer located in Engis, a few kilometers south of Liège, near the river Meuse and it was decided to name this plant: SA HYDROMETAL. Hydrometal is well connected by water, rail and road from its central location in the industrial region of Liege, in the heart of Europe. The company received in 1997 an additional license to process and recycle toxic and hazardous waste. Figure 1 shows a picture of the plant."

Jan 1, 2016

A line of nine self-aspirating W emco cells, part of the Rougher circuit at Division Salvador, Codelco Chile, was retrofitted to allow operation with forced air. Each cell could be operated self-aspirated or with compressed air supplied through a 4-inch line equipped with a mass flow meter. Gas dispersion was characterized for the two modes of operation. Metallurgical performance was compared under self-aspirated conditions and with different gas profiles under forced air conditions. Cell characterization demonstrated that with forced-air the cells could not evenly distribute air across the cell volume. Bubble size increased with gas velocity, as expected, with no difference between self-aspirated and forced-air operation. A systematic increase in bubble size down the bank was found. Cumulative bubble surface area flux down the bank showed no major differences between surveys. However, grade-recovery curves revealed that the highest recoveries were invariably obtained with forced air operation. Plotting concentrate mass recovery vs. enrichment ratio showed that the line performance could be controlled over a wider range when forced air was used.

Jan 1, 2007

By Robert B. Parsons

"The pendulum in Ottawa has swung dramatically from fiscal policy to monetary policy over the last several years. International trends indicate that the pendulum has to start its swing the other way, if Canada's mining industry is to maintain its preeminent position in the global mining arena. This article, which is based on a paper presented by the author at the 37th Annual Meeting of the Newfoundland Branch of CIM, identifies these trends and how they could interact with Canadian policy.IntroductionThe title of this paper is not a very imaginative or catchy one, but it states the topic quite succinctly, if not tersely. This paper looks into a crystal ball to see what might be in store for mine financing over the balance of the current decade.In the event that the reader feels some trepidation about the prospect that such a paper could seek to be the definitive work on the subject, it should be made clear at the outset that this is not the case. The author is, after all, not an economist, a scholar, a financial analyst, or a soothsayer, but is rather a simple accountant who has been closely involved with the mining industry, and the financing thereof, for some twenty years.The paper recognizes that, while a mine may be born when production begins, the mine is conceived when exploration starts. As this act of conception is obviously an essential part of mining, the financing of exploration is also covered in this paper. To attain a focus, this paper approaches the topic of mine financing in the nineties as follows: first, the major emerging forces in the industry are identified: and, second, the implications of each of these forces on financing are considered."

Jan 1, 1991

By C. A. Godden, T. N. Atkinson

Metallographic techniques developed from studies of corrosion films and electroplated coatings on aluminum alloys, are discussed. These methods, the result of work at the Naval Research Establishment, give extremely flat fields at the interface despite the large difference in hardness, in cases where electrolytic polishing could not be used. Techniques to overcome the similarity in refractive index of immersion oil, aluminum ox1d~, and mounting plastic are also considered, as are methods for improving visual and photographic contrast in areas of interest. A device for marking specimens is also de-scribed. ELE•CTROLYTIC polishing is inapplicable in the study of surface films on aluminum, whether corrosion films or electrodeposits. Mechanical procedures must there-fore be followed. Sample flatness and edge retention are of paramount importance. Special measures are required in the study of oxide films, because of the close proximity of the refractive indices of aluminum oxide, mounting plastic, and immersion oil.

Jan 1, 1962