Search Documents

By X. W. Yi, Z. J. Li, G. W. Ma

In this paper, the compressive strength and failure patterns of reinforced cemented paste backfill (CPB) were studied aiming to promote the stability of backfilled stopes. The concept of ductile backfill was proposed and a series of unconfined compression tests were carried out on both non-reinforced and reinforced cemented paste specimens. Portland cement (3% to 5% by weight of tailings) and five different types of ductile materials (0 to 0.5% by weight of solids) were employed in this experiment for the specimen preparation. The test results showed that inclusion of ductile materials enhanced the unconfined compressive strength (UCS), reduced the post peak stress loss and transformed the failure behaviour of specimens from classical brittleness to ductility. The strength of CPB reinforced with different proportions of polypropylene fibres was compared. The stress-strain curves illustrated that both cement and fibres contributed to the increase of UCS, but higher strain values at the peak stress were achieved by fibre reinforcement. CT sliced images acquired from X-ray computed tomography (CT-scan) demonstrated that the reinforced specimen developed irregular crevices at the edge of cross sections and gained the capacity of bearing large displacements owing to the mobilised tensile strength of fibres. It leads to the potential of avoiding unexpected falling blocks of CPB when adjacent mining occurs. This finding highlights a strategy to improve the self-supporting capacity of the fill mass with less cement usage and reduce the ore dilution rates when excavating to adjacent stopes.

Jan 1, 2015

By Brian C. Maynard

"Blast design is becoming more and more important as industrial limitations change in regard to economical and physical restraints. Certainly there are ways to alter the nature of the blast by using different explosives, various hole sizes and modifying the timing and charging details. However, it is not possible to alter the fabric of the rock mass. Therefore, it is necessary to learn more about the rock mass and its role in the blast design, and the resulting fragmentation. The major determinant in the degree of fragmentation, or lack of it, is proposed to be the inherent fragmentation of the in situ rock mass. A practical method of quantifying the discontinuities existing in the rock mass is presented and discussed. Likewise, the effects of inherent fragmentation on the resulting muckpile are reviewed. Finally, a fragmentation model combining the calculated inherent fragmentation and the Kuzram model is shown using a sample blast.IntroductionIn blasting, discontinuity characteristics (Fig. 1) control the method by which the rock mass will behave. Research carried out by Piteau (1970) showed a number of characteristics important in engineering design and, as proposed, in blasting processess. These included:• the nature of their occurrence (i.e. sets or isolated);• orientation and position in space;• continuity; and• intensity"

Jan 1, 1990

By J. F. Hazzard, R. J. Chalaturnyk, C. Khazaei

"Various measurement, monitoring and verification (MMV) techniques are used to ensure the safety of operations in petroleum projects. One of these techniques is microseismic (MS) monitoring of the caprock. A challenge in MS monitoring of caprock is that unlike projects such as tunnelling in hard rocks, the number of recorded events are much smaller and also wide spread through the rock mass which makes interpretation of the physical meaning behind the events very difficult.In this paper, a numerical technique is introduced and validated for coupling a finite difference code, FLAC3D (Fast Lagrangian Analysis of Continua), with a discrete element code, PFC3D (Particle Flow Code). Then, a similar approach is adopted for modeling microseismic events in the caprock. For this purpose, the underburden, reservoir and overburden layers are modeled by FLAC3D. A rather small section of caprock above the reservoir is nulled in the FLAC3D model and substituted by a PFC3D inclusion. The reservoir pressures are then applied to the reservoir section of FLAC3D. Once the FLAC3D cycles, there will be induced pressures in the caprock due to its undrained response to the change in pressures within the reservoir. These induced pressures are transferred to PFC3D as boundary velocities. Then the PFC3D cycles and sends back the boundary forces to FLAC3D. This back and forth process continues until equilibrium is reached. During this process, there will be bond breakages within the PFC3D inclusion that can be regarded as MS events. An algorithm for recording the microseismic energies based on a change in local strains is also implemented. The results are then compared with real data. The effect of injection fluid temperature is also studied. No significant appearance of microseismic events was observed due to injection of CO2 in both cases (i.e. with or without considering temperature). However, this continuum/discontinuum approach seems promising for understanding the microseismic response of caprock in more detail and also using the MS data for validation of geomechanical models."

Jan 1, 2015

By Robert B. Parsons

"With several hoots of the whistle, Canada's fiscal engineers are once again cranking up the income tax locomotive, in an effort to inject new stimulus into a stubborn economy. And once again, additional gears, wheels, levers, and other mysterious part s are being added to the already complex machinery in order to accommodate the new push.This time, a significant new mechanism involves a major overhaul and expansion of the investment tax credit system.Although the shiny new devices have considerable appeal to a certain group of potential passengers, one wonders if all of the renewed chugging and huffing is on the right track.IntroductionAs indicated in Tax Notes in the July 1983 issue of CIM Bulletin , the April 19, 1983 federal bud get introduced a number of new measures which would permit investment tax credits and research and development deductions to "" flow through "" from a corporation to another taxpayer."

Jan 1, 1984

By L. Dekker

"In 1979 Chevron Standard Limited and Irving Oil Limited intersected a thick, high-grade sylvinite zone in the Windsor Group in the Chevron Irving Malagawatch No. I well in central Cape Breton. This well was the third and final hole of a program designed to evaluate a non-commercial oil discovery made by Chevron Standard's Mineral Staff in 1978 while carrying out base metal exploration. Nine holes were subsequently drilled to evaluate the significance of the potash discovery. The delineation drilling proved the Malagawatch structure to be complex with the potash zone showing erratic grade and thickness distribution. Based on the drill information the potash accumulation at Malagawatch is uneconomic, however, other salt ""structures"" in the Bras d'Or Basin may in time prove to have better potential.History of DiscoveryIn 1972 Cuvier Mines discovered the Gays River lead-zinc deposit (MacEachern and Hannon, 1974) which prompted Chevron Standard's Minerals Staff to carry out a study of the Windsor basins in Nova Scotia (Figs. I and 2). As a result of this program several carbonate-hosted lead-zinc prospects were identified in the basal Windsor carbonate; one of these was at Malagawatch on Cape Breton Island . In 1978, after preliminary exploration surveys, a diamond drill program commenced consisting of 5 BQ holes (Fig. 3), three of which tested the basal carbonate. Instead of the reefoid bank facies of the Gays River Formation (Giles et al., 1979), the favoured host for economic base metal mineralization, this carbonate was developed as a laminated, pelletoidal, lime packstone more characteristic of the facies equivalent Macumber Formation (Schenk, 1967). While drilling one of these holes, No. 3-78, oil scum was intermittently detected on the drilling mud. The hole was abandoned at 191 m in anhydrite, without having reached the basal limestone."

Jan 1, 1985

"The Schist Lake mine, owned and operated by the Hudson Bay Mining and Smelting Co., Limited, is situated on the northwest arm of Schist Lake, 4 miles southeast of Flin Flon, Manitoba.The deposit was discovered early in 1947, during a diamond drilling program exploring small copper showings along the west shore of the lake. The orebodies came to surface between the mainland and the north end of Stitt Island.Production began in August, 1954, at an initial rate of 300 tons per day. Underground workings have been carried to the 1,700-foot level, where exploration work is now being done.General GeologyRocks of the area are Precambrian lava flows, with associated pyroclastic breccias and tuffs, and related minor intrusions. Their general strike is northwest and their dip is nearly vertical. Shearing is common and is related to the activity which caused intense folding and much faulting in the area. The larger faults and the fold axes trend a few degrees west of north. The lavas are mainly andesitic but a layer of sericite-carbonate schist, which is probably derived from a fine-grained, grey quartz porphyry, occupies most of Stitt Island and extends into the mine area. It is within this layer of schist that the ore deposit occurs (Figure 1).The OrebodiesThe ore occurs as tabular to lens-shaped bodies which strike northwest, dip nearly vertically, and plunge at 60 degrees to the southeast. The ore zone is 800 feet long and has been traced for a distance of 2,000 feet along the plunge (Figure 2). The maximum length of continuous ore within this zone is 200 feet. Widths of individual ore lenses vary from a maximum of 35 feet to a minimum of 2 feet.The ore consists of three distinct types: massive sphalerite-pyrite, massive chalcopyrite-sphalerite, and disseminated chalcopyrite-pyrite. The No. 1, or eastern, orebody is predominantly massive sphalerite-pyrite. The western part of the No. 2 orebody is massive chalcopyrite-sphalerite. The disseminated ore forms the eastern part and the lower end of the No. 2 orebody. All three types of ore, with patchy distribution, are found in the smaller lenses below the 1, 100-foot level.Metallic minerals, in order of deposition, are pyrite, arsenopyrite, chalcopyrite and sphalerite, galena, enargite, and gold. Both massive types of ore exhibit banding in many places, probably as a result of the selective replacement of schist. The disseminated ore was formed as a filling of the interstices in a brittle chert rock which appears to have been crushed by the same forces which produced the schist."

Jan 1, 1949

By J. W. Hendry

"This paper will discuss the application of tools and the evolution of computer-assisted procedures in the production planning process at Quintett e Coal Limited (QCL). In 1986, QCL produced 5.3 Mt of clean coal from their surface mining operation located in north eastern British Columbia. The structural complexity of the sedimentary deposit and high rate of mining necessitate the consideration of large amounts of geological information which continually updates the interpretation. There are multiple unit operations required during the process of mining through a given multi-seam sequence, which results in many interdependent faces, and multiple iterations of scheduling sequences in order to satisfy a given set of objectives. In order to facilitate these activities in a timely fashion, it was recognized that a computer systems' capability needed to be developed which could increase the efficiency of information input, manipulation and output. IntroductionQuintette Coal Limited (QCL) has been operating a large metallurgical open pit coal mine in northeastern British Columbia, since 1982. The mine produced 5.3 Mt of clean coal in 1986 for export to Japan. Throughout the start-up period and the subsequent build -up of production levels, it became evident that the primary producing area was comprised of extremely complex faulted structures. This has resulted in development and modification of specialized mining methods employed to effectively recover the resource. Similarly, the planning and engineering techniques employed have been evolved over the same period of time. The implementation of computerized methods has been one of the major developments in this process, including geology interpretation, modelling, reserve definition, quantification, production planning and scheduling, and graphical plan presentation. These capabilities have been employed, in various forms, for project scale feasibility work and long range planning for some time, however, the use of computer tools for short-term, detailed production planning of a complex mining environment presents a different set of problems. It is hoped that a presentation of the current state of evolution and future plan s for development will be of interest to organizations considering implementation of a similar system."

Jan 1, 1988

By L. J. Visentin, J. G. Rickaby

"Audiometric testing is a key element in hearing conservation in the mining environment. This paper gives the history of the audiometric testing program carried out by Inco Metals Company, including the program objectives the personnel and equipment involved, calibration and testing, the test procedure, and the classification and evaluation of the test results.IntroductionThe operations of the Ontario Division of Inco Metals Company are located primarily in the Sudbury District. They also include a refine ry at Port Colborne and a mine and concentrator at Shebandowan near Thunder Bay.The company operates nine underground mines, and one open pit, while maintaining six underground mines on a standby basis. Ore from these operations is processed in four concentrators. The metallurgical facilities include a smelter, a matte processing plant, a copper refinery, a nickel refinery and an iron ore recovery plant at Sudbury, and a nickel refinery at Port Colborne. Inco Metals currently mines roughly 9,000,000 tons annually and produces IS elements.Excessive noise in the work place has been a serious problem in the mining industry since the introduction of compressed-air-powered machinery in the last century. At the same time, growing levels of noise inherent in our social environment can threaten the hearing of employees and their families.Only in the last 20 years, however, has the extent of this problem and its implications for people working in the industry and their families been recognized. Since the industry has become aware of the situation it has taken steps to implement comprehensive noise reduction and hearing conservation programs."

Jan 1, 1982

By N. E. Chaouai, M. Lavigne

"Indicator kriging is one of the non-parametric geostatistical techniques, ideal for estimating the reserves of irregular mineralizations (e.g. gold, uranium, platinum, diamonds, etc.). Such mineralizations are characterized by variograms which are very sensitive to extreme values (outliers) and very difficult to model.The classical approach to this problem in the industry is to trim off these high grades using arbitrary empirical upper limits established either from practice or subjectively. Contrary to this simplistic approach, indicator kriging discretizes the histogram of the grades (usually log normal) in several classes and carries out interpolation separately for each class. This paper gives an overview of the differences between ordinary and indicator kriging along with the steps required to carry out indicator kriging. The paper concludes with a case study involving a gold deposit estimation.IntroductionParametric geostatistics (ordinary kriging) has given us satisfactory results over the years in estimating the reserves of well behaved deposits with coefficients of variation close to 1 (e.g. sedimentary and porphyry type deposits). However, numerous problems have been encountered in estimating irregular mineralizations (e.g. small vein deposits of precious metals) with high coefficients of variation in the range of 2 to 5. Such deposits are characterized by a very small proportion of extreme values (outliers) which create distortions on the variograms (pure nugget effect) and render them useless(1,2).The solution often followed by the mining industry today is to trim off these values based on empirical limits. These limits are derived either by comparison with production results (or bulk samples) or by geological interpretations. Needless to say that such manipulations can lead to serious errors in estimating ore reserves (usually underestimation of total metal quantity), especially when production results or bulk samples are absent.On the other hand, the solution followed by the geostatisticians in the past was to smooth out the data using transforms (e.g. normal-score or natural logarithms). Such transforms are nonlinear and they required non-linear estimation techniques such as disjunctive kriging (DK) or multivariate gaussian kriging (MG) which require normal related hypotheses, not necessarily true in geology.Nonparametric geostatistics (indicator and probability kriging) have been -developed in order to handle these problems related to highly skewed distributions."

Jan 1, 1990

By Dallas W. Davis

"Since May 1980, New Brunswick has called separate tenders for the right to explore and develop several potash prospects, as well as areas underlain by Alberta oil shale. These tender calls had in common the provision for a basic ad-valorem royalty, combined with sharing of cash flow after exceeding a 15-20% discontinued cash flow rate-of-return threshold. In the case of potash, the bidding variable was a share of cash flow, but for oil shale it was exploration expenditures committed, with the cash flow sharing to be negotiated at the time of application for a production lease. The Millstream potash occurrence, previously discovered by government drilling, received five bids (21.1% highest), the Dorchester ""grassroots area"" with four surmised drill targets apparently received no bids, and in the case of oil shale there were only two bids on the one block previously subjected to the most exploration.It is concluded that New Brunswick will not be successful in awarding the potash or oil shale rights in return for a comparable level of basic royalty and cash flow share as in the case of Millstream, unless it spends money in discovering prospects or sharing the exploration risk with companies. The approach is likely to work for oil shales only if current exploration proves the existence of much high-quality material or a definite trend of real increases in the price of oil is again established. Undoubtedly, it continues to be desirable to assure an on-going stable investment climate through award of potash and oil shale rights under terms which provide for a return that the public and future governments will consider fair. This could mean that some form or risk sharing with companies would be advisable."

Jan 1, 1983

By John A. Meech, Irene E. Cristoveanu

"The separation of hematite fines (100% - 38 um) from quartz fines (100% -75 um) was investigated using coarse hematite (-212 + 150 um) as a carrier in an oleic acid collector system. Oleic acid additions, per cent coarse additions, combined conditioning time and ferric chloride additions were examined.It was found that carrier flotation is a dominant mechanism for fine hematite recovery at oleic acid levels greater than 200 g/t and coarse additions of 10 per cent. Hetero-aggregation is favoured under conditions of lower levels of oleic acid in the presence of ferric chloride and at conditioning times greater than ten minutes.Ferric chloride acts as a depressant for pre-reagentized coarse hematite at oleic acid levels below 150 g/t. At concentration levels above 500 g/t, ferric chloride interferes significantly with the success of carrier flotation of fine hematite.The sensitivity of carrier flotation to changes in oleic acid addition, ratios of fine and coarse material, conditioning time and the presence of an inorganic electrolyte emphasizes that its application is only suitable when flotation conditions can be stabilized.IntroductionThe production of fine material is unavoidable during the comminution of iron ore . Due to the difficulty of recovering iron from this fine material by various gravity separation methods, flotation can often be a more attractive process producing high-grade material at high recovery. One variation of the flotation process, that can be useful for recovering ultra fine minerals (<10 um) , is known as carrier flotation. This process involves the utilizat ion of coarse particles ( > 150 p.m) which act as flocculation centres to which the fine hematite particles (10 - 40 u.m) become attached and are carried or "" piggy-backed"" into the froth phase."

Jan 1, 1985

By Jorgen Elbrond, Yve Lizotte

"A mathematical procedure for determining the underground mining level layout which minimizes the total costs of excavation and haulage is described. This procedure has the advantage over previous graphical procedures of being easily amenable to microcomputers. The paper demonstrates through examples how the procedure can be applied to minimizing discounted costs of level layout as well as providing the optimal location of a production shaft.IntroductionIn recent years there have been numerous publications in mining journals concerning the minimization of mine haulage costs. With the rapid escalation of energy costs during the last decade it is not surprising that several studies applying queuing theory, simulation and mathematical programming to mining related transportation problems have been successfully undertaken. Because of the increasing availability of various sizes of computers these techniques have gained considerable popularity as evidenced by the numerous commercial packages presently being marketed.The publications concerned with haulage cost minimization are generally concluded along the lines of &apos; ... haulage costs at production rate x will be minimized by assigning y units to location z...&apos;. Details about the route followed and whether it guarantees a minimization of costs are seldom considered. Route data has to date been manually resolved and used for input to developed programs. It would appear that no program has been developed to date which simultaneously minimizes costs by both fleet assignment and routing network resolution.Another important factor in transportation problems is the investment cost associated with the routes; road construction costs or, in the case of underground levels, drift excavation costs. Except for special cases the transport network which minimizes haulage costs only will not provide a minimum excavation cost solution.Zarnbo(1) illustrates by graphical and mathematical procedures how central &apos;facilities&apos; can be located to simultaneously minimize investment in the transport network and haulage costs. Unfortunately these procedures and others recently applied to mine haulage problems do not provide solutions to the generalized problem. Also because these procedures are geared to graphical solutions and hand computations whereby certain possibilities can be &apos;visually&apos; eliminated, they can be tedious to program and present storage capacity constraints with current microcomputers."

Jan 1, 1985

By Lastram Rolando, Larry J. Hulbert, Louis J. Cabri, J. H. Gille Laflamme, John L. Campbell, Soey H. Sib, Chris G. Ryan

"The mineralogy of samples from the Wellgreen Cu-Ni-Pt-Pd deposit, Yukon Territory, is complex and the metals of interest are contained within fine-grained minerals which vary in size and mineral associations from sample to sample.The major Ni carriers are pentlandite and violarite; the major Cu carrier is chalcopyrite. About 700/0 of the major Ni carriers and 78% of the major Cu qurier will be liberated at a grind of 80% -U,.7 ,an (-500 mesh) for typical low-grade gabbro (West zone, sample No.1). For typical ""clinopyroxenite"" (West zone, sample No.2) and typical ""clinopyroxene-rich peridotite"" (East zone, sample No.3) the liberation would be 71% and 65% for Ni, 74% and 60% for Cu, respectively. Fine grinding, however, cannot liberate the Ni contained in silicates and pyrrhotite, estimated to total 24.5% for typical low-grade gabbro (West zone, sample No. I), 15% for typical ""clinopyroxenite"" (West zone, sample No.2), and 12% for typical ""clinopyroxene-rich peridotite"" (East zone, sample No.3).The principal Pt carrier (sperrylite) varies considerably in grain-size between samples and fine grinding, required to liberate the major Ni and Cu carriers, may be counterproductive in samples where sperrylite is relatively coarse-grained, as some would then be unrecovered (e.g. sample No. 1). In addition, sperrylite in samples No.2 and No.3 is closely associated with magnetite. Palladium occurs in diverse ways. It occurs in the form of several Pd minerals (e.g. sudburyite, testibiopalladite, merenskyite), as a replacement for Ni in several tellurides, antimonides and tellurantimonides (e.g. melonite), or as very low concentrations in pentlandite (up to 34 ppm), chalcopyrite (up to 9 ppm), and pyrrhotite (up to 5.6 ppm). Palladium minerals and Pd-bearing minerals are strongly associated with chalcopyrite in sample No. 1 and will thus report to a Cu concentrate.However, 22% of the total Pd is in solid solution in pentlandite in this sample and will thus report to the Ni concentrate. In samples No.2 and No.3, less Pd occurs in solid solution in pentlandite, and the PGM are distributed mainly among pentlandite, chalcopyrite, and magnetite in sample No. 2, and among pentlandite, pyrrhotite, chalcopyrite, and magnetite in sample No.3. Therefore, the feasibility of magnetic concentration should be investigated for samples like No. 2 and No.3, in order to improve Pt and Pd recoveries. Rhodium was found to occur as rare hollingworthite, in sparse cobaltite (up to 2.7%) and, as low concentrations in chalcopyrite (to 10 ppm) and pentlandite (to 12 ppm) by proton microprobe. Iridium occurs in hollingworthite (up to 7.8%) and very rarely as the native metal or in an undefined Re-Ir-Qs..Ru alloy. Ruthenium was determined by proton microprobe analyses to occur in pentlandite (up to 13 ppm) and chalcopyrite (up to 10 ppm), in addition to rare laurite and Re alloy."

Jan 1, 1993

By W. W. Muir

"The Baker Mine used a 100-ton per day conventional cyanide leach mill located in northern British Columbia. A production decision was made in early 1980 and the mill was on fine in April 1981.Ore reserves had been estimated at 100,000 Ions averaging 0.9 oz gold per ton and 18 oz silver per ton . Mineralization consists of electrum (Au/Ag) and acanthite (Ag2S).This paper will review plant design and focus on some problems associated with start-up and early operation with the intention of assisting other mine operators by indicating potential problem areas.IntroductionThis paper will discuss operating strategies employed at Baker which improved over-all mill performance. Also included are some ideas which could be steps toward a more efficient operation in a similar setting.Actual dore production by mine life was 37,606 oz gold and 742,117 oz silver.Figure 1 illustrates the relative stability attained over the mine life. Metal recoveries for gold and silver were 92% and 85% respectively.Safety at Baker was of prime importance because of its remote location. Baker received the Mine Safety Association ""Small Mines Award "" in two of its three operating years. At shutdown in late 1983 the mill had operated for over 850 days without a lost-time accident."

Jan 1, 1985

By W. H. White, A. J. Sinclair

"Unaltered biotites from three samples of monzonite and gabbro from the Copper Mountain stock and a single sample from a pegmatic biotite-chalcopyrite vein cutting the Triassic Wolf Creek formation have a mean K-A age of 193±7 m.y. These data support a suggestion based on geological evidence that Copper Mountain ore deposits are related genetically to the Copper Mountain stock.A cogenetic mineral pair (biotite and clinopyroxene) from a sample of sericitized and chloritized monzonite of the Copper Mountain stock have identical K-A ages of 150 m.y., which probably represents a time of wide-spread, post-ore, hydrothermal alteration. This alteration is believed to be related genetically to a group of post-ore intrusions known as the ""mine dykes,"" suggesting that they also have an age of 150 m.y."

Jan 1, 1968

By P. R. A. Andrews, I. Jackman

"A mineral processing investigation to recover chromite was performed at Lakefield Research, under the guidance of CANMET personnel, on a 70 tonne ore sample from the Bird River deposit in Manitoba. In the laboratory phase a flowsheet was developed which involved grinding, gravity separation and flotation. The gravity concentrates were upgraded by magnetic separation and the flotation concentrates by gravity concentration . Pre-concentration by electronic ore sorting, magnetic separation and heavy media separation also was examined.The developed flowsheet was applied on a pilot-plant scale in the second phase of the testwork to the ore as received, and to ore pre-concentrated by electronic ore sorting and magnetic separation. Ore pre-concentrated by heavy-media separation was treated on a laboratory scale based on the pilot-plant flowsheet ,Processing the are as received resulted I n 77% recovery of chromite in a concentrate analyzing 30% Cr20 J; processing are pre-concentrated by electronic are sorting resulted in 64% recovery of chromite in a concentrate analyzing 30.5% Cr20J."

Jan 1, 1988

By Sabine Noelte, Mikko Petteri Rantamäki, Christopher Robben, Anssi Takala, Karl-Erik Rånman

"Sensor-based ore sorting is on its way to establish as a standard option for physical separation. The increasing number of installations in coal, iron ore, industrial minerals and hard-rock metal mining segments underlines the technological and financial potential that is beginning to be untapped. The Ma’aden Phosphate installation with 1.650 t/h sensor-based ore sorter feed sets a new benchmark for the possible capacity of stationary installations. Besides stationary installations, including multiple sorters parallel in different size ranges and multiple stages, containerised semi-mobile plants are applied. These offer two advantages, first being the reduction of transport costs when applied close to the mining face. The second is that semi-mobile systems enable processing of tens of thousands of tonnes of ore in a piloting phase with an approximate duration of 0.5 to six months, verifying the results laboratory mini-bulk tests on 5–10 tonnes of sample. This is especially important for low-grade metal ores because of the inherent Fundamental Sampling Error, as well as the Grouping and Segregation Error. The paper elaborates the results achieved within the I2MINE project, treating polymetallic ore at the Boliden Concentrator in Sweden.INTRODUCTIONSensor-based ore sorting (SBS) is becoming a standard option for physical separation, applied in all segments of mineral production. The Umm Wu’al project sets the bar for stationary SBS installations with 1,650 t/h feed (TOMRA, 2015). TOMRA Sorting Solutions has finalised an agreement in cooperation with Outotec to supply Outotec-branded sorting solutions for the mining and metallurgical industry (TOMRA, 2014). Especially for low-grade hard rock metal ores, an interdisciplinary approach is necessary applying experts for all aspects of mineral production. Due to the impact on the whole process stream, it is important on the end user side to have high level managerial support and involve all disciplines to ensure that all stake holders are involved in the analysis."

Jan 1, 2016

By André Bérubé

"IntroductionSince the disappearance of Les Forges du Saint-Maurice at the end of the last century, many historians have taken an interest in the lengthy past of this enterprise. They considered the political, socio-economic, administrative and anecdotal aspects of the industry, but barely dealt with the elements of technology. The purpose of this article is to try to fill this gapru.Les Forges du Saint-Maurice was an integrated industrial concern, specializing in the production of semi-finished wrought iron and finished cast iron, that operated almost without interruption between 1734 and 1883. Les Forges first came into being in 1729, when Montreal merchant Francois Poulin de Francheville submitted to the king of France a request for the right to exploit the bog iron ore deposits on his seigneury of Saint-Maurice. This request, agreed to in 1730, was one of a long series of attempts, previously unsuccessful, to establish a local iron industry in the colony. Several such proposals were held up by a lack of capital from promoters or a too rigid application of the mercantilist policy by the metropolis. In 1730, however, the French minister Maurepas favoured a more liberal policy which would encourage private enterprise. The benefits of an iron industry to the naval construction industry was a factor that caught the attention of administrators. The choice of the site for Les Forges was based on the following factors:• the abundance of surface deposits of bog iron ore in the Saint-Maurice region;• the presence of a vast supply of hardwood and conifers needed in large quantities by this industry;• the proximity of sandstone and limestone deposits, indispensable materials for the construction and operation of the blast furnace;• the presence of a water stream, with sufficient flow to provide the hydraulic power needed for the operation of the machinery."

Jan 1, 1983

By Scott K. Palm, Neil D. Pearson, Jr. Read

"Uncertainty is an important feature of many investments, but it is especially important for mineral properties. Mine properties often entail large investments and fixed commitments. Managers in the mining industry often view price uncertainty as undesirable, due to the possibility that the price of the mined commodity will fall to a level that prevents the firm from recovering its investment and fixed costs. This paper identifies pitfalls in conventional valuation methods and outlines a new approach to valuation based on option pricing theory and dynamic programming. In the process, it identifies generic strategies for organizing mine production in ways that allow the owner to benefit from the uncertainty in mineral prices. IntroductionRisk is pervasive in the mining industry. The operation and maintenance of a mine may involve high, and unavoidable, fixed costs. A mine owner can only begin to recover these fixed costs if the price of the mined commodity is greater than the incremental cost of production. But the prices of many minerals are extremely volatile. The price volatility of copper has been significantly higher than the price volatility of a typical stock, for example. A mine owner cannot be sure that the price of the mineral product will remain high long enough for the firm to recover its capital and fixed costs.Mine owners are able to minimize their losses during periods when the output price is below the incremental cost of production by temporarily closing operations. During these periods they incur only fixed costs. While shut-downs help minimize losses, the y do not help the firm recover its initial investment. If output prices remain low long enough, the fixed costs and original investment may never be recovered. High fixed costs, therefore, lead to substantial downside risk."

Jan 1, 1986

By F. J. Macias, A. Bruland, F. E. Dahl

"Tunnelling by use of Tunnel Boring Machine (TBM) is gaining a greater presence as a suitable excavation method. Disc cutter consumption has a strong influence on performance and cost when using TBMs and the influence becomes even more relevant in hard rock. Furthermore, good predictions of TBM performance and cost facilitate the control of risk as well as avoiding delays and budget overruns. Since abrasive wear is the most common process affecting cutter consumption, good laboratory assessments are needed. A new abrasivity test method called Rolling Indentation Abrasion Test was developed. The goal of the new test design and procedure is to reproduce wear behaviour on hard rock tunnel boring in a more realistic way than traditionally used methods by introducing wear by rolling contact on intact rock samples. INTRODUCTIONHigh investments are involved in the tunnelling industry, especially in Tunnel Boring Machines (TBMs) projects. Performance predictions and cost estimations are crucial for planning and risk management of TBM projects. Cutter consumption has a large influence in terms of time and cost, and an even greater effect in case of hard rock projects. Many factors are influencing the amount of cutters consumed in hard rock TBMs. Normal TBM operation results mainly in abrasive wear on the cutters and appropriate methods for abrasivity assessment are needed. Rock abrasiveness cannot be considered as an intrinsic property and the complete tribological system should be considered in addition to the geological properties of the rock.In the present paper, a new test method for abrasivity assessment in tunnel boring called Rolling Indentation Abrasion Test (RIAT) is presented. The traditionally used test methods for determination of rock abrasiveness uses sliding or impact contact in order to cause wear while the RIAT introduces rolling contact on intact rock samples. The ambition of the new test device is to have a reliable method to evaluate the cutter wear in hard rock tunnel boring by reproducing wear behaviour on rolling disc cutters in a more realistic way. It has been established by many authors that the abrasion of a cutter ring is proportional to its rolling distance (Rostami, 1997; Bruland, 1998). In the present work, the weight loss of a mini-cutter ring is measured subsequent to testing in order to evaluate wear in the rolling process and could hence be related to cutter ring wear. Indentation of the tools in the intact rock sample is considered as an indication of the surface hardness of the rock or the resistance to indentation by rolling."

Jan 1, 2015