Search Documents

By James F. Allan

"The Kipawa yttrium-zirconium prospect is located about 150 km south of Noranda, Quebec. Yttrium-zirconium mineralization occurs in an elongate, regionally metamorphosed and deformed peralkaline complex in the Grenville terrain. The mineralized zone, as defined by =.0.10% Y2O3, is 1300 m long and 10 m to 30 m wide. Zirconium content typically ranges from 0.50 to 1.20% ZrO2, The mineralized zone strikes northwest and dips 20 degrees to 35 degrees to the southwest. It occurs at the structural base of the peralkaline complex in syenite gneiss and calc-silicate rocks and is conformable with both the footwall contact of the complex, and the layering and gneissosity in the enclosing rocks. Minerals of economic interest are eudialyte (sodium-zirconium silicate), mosandrite (sodium-titanium silicate), britholite (calcium-silica phosphate), and a few other uncommon zirconium and titanium silicate minerals.The highest and most continuous yttrium grades occur in the upper part of the syenite gneiss unit in areas containing eudialyte, mosandrite and minor britholite. Yttrium also occurs in britholite in calc-silicate rocks and in mosandrite in syenitic rocks in the lower part of the syenite gneiss unit. Both the yttrium-bearing minerals and yttrium grades are erratic in the lower part of the unit. Zirconium is generally more uniformly distributed than yttrium. A peralkaline granite gneiss phase of the complex intrudes the syenite gneiss and possibly truncates it, and the mineralization, near the southern boundary of the mineralized zone.The mineralized zone is coincident with a radiometric anomaly and discontinuous yttrium and zirconium soil anomalies.More drilling and metallurgical studies will be required to determine the economic viability of the yttrium and zirconium mineralization at Kipawa."

Jan 1, 1992

By Eiichiro Mizushima

Catalyst systems comprising (Ph3P)AuCH3 and acid co-catalysts were found to be highly efficient for hydration of alkynes to give ketones. Methanol was the best choice of solvents. Introduction Hydration of carbon-carbon unsaturated bonds is one of the environmentally benign routes to the carbon-oxygen bond formation. Hydration of alkynes forming carbonyl compounds, an important variation in this category, is a well known reaction which has been extensively studied. The reaction by acid-catalysis is the most conventional method, while it is applicable only to electron rich acetylenes to obtain satisfactory yields (1,2). The hydration of simple alkynes usually requires another catalyst (co-catalyst), typically a mercury(II) salt (3), which is inconsistent with the guiding principle of Green Chemistry (4).

Oct 1, 2003

By P. Patnaik, F. Cuneo, D. M. Wang

Microwave (MW) energy has been used widely for several decades for communications, food processing, wood drying, vulcanization of rubber and medical therapy. Recently, this technology was found to be capable of successfully sintering ceramic and metallic powder materials, with the advantages of reducing soaking times and sintering temperatures. Unlike conventional heating, MW radiation works through the absorption of the microwave energy by a material placed in an electromagnetic field within the microwave cavity. A far more efficient heating process is produced due to the unique ability of microwaves in selectively heating a pecific part of the material with desirable dielectrical properties. This exploratory research was initiated with the objective of locally sintering the thermal barrier coating of gas turbine components using MW radiation. This novel technique may allow repairing of the component without subjecting the entire piece to unnecessary elevated temperatures and reduction of process time and cost. Y ttria stabilized zirconia was used in this study and sintering was conducted using a multimodal 1.2 kW microwave facility. Three configurations of heating setup were experimented and the preliminary results will be discussed in this paper.

Jan 1, 2006

By C. M. Trigg

"PEC uranium deposit, 100 km southwest of Coppermine, was discovered by diamond drilling in 1976 following ground and airborne geophysical surveys, geological mapping, geochemical surveys and boulder prospecting that were initiated as the result of the discovery of uraniferous sandstone outcrops in 1969 by geologists of Aquitaine Company of Canada Ltd.The deposit is within gently northeasterly dipping medium to coarse-grained Unit 11 quartzitic sandstone of Neohelikian Dismal Lakes Group. The deposit is from 10 m to 70 m above the base of the sandstone which, beneath the deposit, non-conformably overlies weathered and altered Aphebian granite of Great Bear Batholith or unconformably overlies rubble breccia, conglomerate and medium-grained Unit 8 sandstone of Paleohelikian Hornby Bay Group.A northeasterly trending, 500 m wide graben, bounded by the steeply dipping northeasterly striking Imperial and Aquitaine faults, contains the deposit which is 1.1 km long by up to 340 m wide. The deposit overlies a post-Hornby Bay Group, pre-Dismal Lakes Group topographic high. Uranium principally occurs as stratabound, often peneconcordant bands; a lesser amount of uranium is fracture controlled.Stratabound uranium exists in gently easterly dipping, subparallel bands ranging in thickness from 1.5 m to 6.0 m. Pitchblende, coffinite and sooty black uranium oxides occur as interstitial disseminations and grain coatings subparallel to bedding; they also replace pyrite and form narrow veinlets.Small amounts of torbernite, carnotite and cuprosklodowskite coat pitchblende and are disseminated within mineralized bands. Pyrite, marcasite, chalcopyrite, chalcocite, cove/lite, digenite, azurite, malachite, arsenopyrite, glaucodot, niccolite, bravoite (? ), goethite, hematite and magnetite as well as quartz, barite, calcite, biotite, chlorite and clay minerals exist within the mineralized bands. Uranium grades of 0.1 % to 0.3 % U3O8 over thicknesses of 1 m to 2 m are typical.A steeply dipping fracture zone near the Imperial fault contains sooty black uranium oxides, torbernite, carnotite and cuprosklowdowskite as well as sulphides, cobalt arsenides, quartz and carbonate. The zone may reach 70 m long; its true width is about 1.9 m. Uranium grades range up to 5.18% up, over0.9m.Pitchblende and coffinite from PEC deposit have been dated at 1.08 ± .10 Ga with possible remobilization at .45 Ga. The deposit contains an inferred 3,150 tonnes of U3O8."

Jan 1, 1986

By W. Beres, R. E. Miller, B. Shiari, L. R. Zhao

A dynamic multiscale simulation method has been developed to study the material scratching processes on nanoscale single crystals. The model simultaneously captures the atomistic mechanisms near the free surface and the long range mobility of dislocations and their interactions, without the computational cost of full atomistic simulations. The method also permits the simulation of system sizes that are approaching experimentally accessible systems, albeit in 2D. Simulations are performed on single crystal aluminum to study the atomistic details, surface evolution, and generation and propagation of dislocations for a variety of scratching depths at room temperature. Simulations demonstrate the power of the developed method in capturing both long-range dislocation plasticity and short-range atomistic phenomena during tool advance. Variations of scratching normal and tangential forces are investigated and related to plastic deformation and dislocations generation during the simulation process.

Jan 1, 2006

By D. Sammut, F. Houllis, J-L. Huens, J. Moyes

The Intec Gold Process has been developed as a halide-based alternative for the recovery of gold from refractory sulphide deposits. The halide medium allows sulphide oxidation and gold extraction to be performed concurrently at moderate temperature and atmospheric pressure sourcing oxygen from direct air injection. The dissolved gold is loaded onto activated carbon and stripped in a conventional Zadra circuit. High gold extractions have been achieved from a range of refractory gold concentrates at laboratory scale, which has led to a continuous locked-cycle pilot plant program. The pilot plant operated at >99% availability, with a maximum of 96.5% gold extraction from a concentrate containing 58.6 g/t gold. >99% of the dissolved gold was loaded onto carbon at up to 1% w/w, with no loss of carbon activity detected over five loading/washing/elution cycles. This paper describes the process and presents both laboratory and pilot plant results as well as economic data from two costing studies.

Jan 1, 2005

By O. S. Perry, G. H. Charlewood, K. Griffin, S Ogryzlo, H. Hopkins, G. MacIntosh

"The gold mines of Kirkland Lake are in Teck township, Timiskaming district, Ontario, latitude 48°9'N. and longitude 80°3'W., at an elevation of 1,038 feet above sea-level.There are seven contiguous producing mines in a length of 3;1/2 miles along the general east-west strike of the deposits. The seven mines are, in order from west to east, Macassa, Kirkland Lake, Teck-Hughes, Lake Shore, Wright-Hargreaves, Sylvanite, and Toburn.The first discovery of gold in the zone was made by W. H. Wright in 1911 on the east claim of the Wright-Hargreaves property, and the following year the Tough brothers and H. Oakes found gold in what is now the No. 1 vein_ at the Toburn. Production began at the Toburn in 1915, followed by Teck-Hughes in 1917, Lake Shore in 1918, Kirkland Lake Gold in 1919, Wright-Hargreaves in 1921, Sylvanite in 1927, and Macassa in 1933.To the end of 1946, 31,938,350 tons of ore had been milled at the Kirkland Lake mines, from which 16,132,700 oz. gold, having a value of $498,517,600, were recovered. The bullion varies from mine to mine between 800 and 900 fine, the average for all the mines being 853. The average fineness of the native gold is 941.The workings of some of the mines are more than 6,000 feet deep and sinking to depths below 7,000 feet is now in progress.GENERAL GEOLOGYThe regional structural geology of the area in which the mines of Kirkland Lake occur is described in a preceding paper in this volume by J. E. Thomson."

Jan 1, 1954

By Qing-Xun Low

Ni current collector has excellent electronic conductivity and mechanica, properties. However, nicke, cannot be used in H2S-containing syngas SOFCs due to sulfur poisoning and coking. Copper coated nicke, is prepared by electrochemica, deposition. XRD, SEM, and EDX techniques are used to characterize the samples. After high temperature treatment in syngas containing, the coated samples exhibit high resistance of coke formation and sulfur corrosion compared to pure nickel. Therefore, copper coated nicke, is a promising anode current collector for H2S-containing syngas SOFCs.

Jan 1, 2010

By E. Demedde

Carbon anodes in aluminium reduction cells are continuously consumed during electrolysis. In prebake cells the anodes are replaced at regular intervals. The spent anodes, called butts, are often allowed to cool in air while emitting fluorides into the building from the hot alumina cover and the adhering bath. In modem smelters spent anodes are placed inside enclosures and fluoride emissions during cooling are effectively reduced. Fluoride emissions from spent anodes were estimated by considering the kinetics of fluoride formation, a heat transfer analysis of the cooling anode butt and the ventilation flow from a cavity. Fluoride emissions from large anode butts cooling inside enclosures were compared with those cooling in air. Good agreement with published experimental values was obtained for enclosures having different leakage opemngs, when a hydrofluorination reaction of the spent anodes was included.

Jan 1, 2006

By P. K. Kaiser, S. Maloney, S. Yazici

"This paper focusses on the strength or capacity of cable bolts and introduces a new perspective for cable bolt design by demonstrating that mining-induced stress changes may affect cables in a detrimental manner. The concept underlying a novel cable bolt pull-out resistanceor bond capacity model is described and its practical significance is demonstrated by application to a simple two dimensional scenario of a fall-of-ground.A number of practical implications emerging from the application of this model are discussed to provide guidance to ground control personnel jar improving cable bolt support systems in mining applications. These include cable layout optimization, use of cable pre-reinforcements, assessment of embedment length requirements, need for plated cables (or straps), use of bird-caged cables (or buttons), and grout quality issues.IntroductionDuring the last decade, cable bolting has become a standard support technique in mining for handling wide spans, reinforcing are passes, preventing or reducing dilution of ore in marginally stable stopes, and for many other rock support need s.In its infancy, many deficiencies in cable bolt supports resulted from improper installation techniques and, in particular, grout quality control problems and the use of empty breather tubes (Goris, 1990). The development of special grout pumps and fail proof placement procedures (Oliver, 1992; Bourchier and O'Flaherty, 1992) have eliminated many of these early problems. Nevertheless, there are still situations where cables seem to lose their capacity during mining, and in these cases the cables do not provide the expected and needed ground support. In some instances, cables perform extremely well, whereas in others the same support layout and quality of support installation seem to be insufficient, allowing falls-of-ground or progressive cavings to occur."

Jan 1, 1992

By James F. Allan

"The Kipawa yttrium-zirconium prospect is located about 150 km south of Noranda, Quebec. Yttrium-zirconium mineralization occurs in an elongate, regionally metamorphosed and deformed peralkaline complex in the Grenville terrain. The mineralized zone, as defined by =.0.10% Y2O3, is 1300 m long and 10 m to 30 m wide. Zirconium content typically ranges from 0.50 to 1.20% ZrO2, The mineralized zone strikes northwest and dips 20 degrees to 35 degrees to the southwest. It occurs at the structural base of the peralkaline complex in syenite gneiss and calc-silicate rocks and is conformable with both the footwall contact of the complex, and the layering and gneissosity in the enclosing rocks. Minerals of economic interest are eudialyte (sodium-zirconium silicate), mosandrite (sodium-titanium silicate), britholite (calcium-silica phosphate), and a few other uncommon zirconium and titanium silicate minerals.The highest and most continuous yttrium grades occur in the upper part of the syenite gneiss unit in areas containing eudialyte, mosandrite and minor britholite. Yttrium also occurs in britholite in calc-silicate rocks and in mosandrite in syenitic rocks in the lower part of the syenite gneiss unit. Both the yttrium-bearing minerals and yttrium grades are erratic in the lower part of the unit. Zirconium is generally more uniformly distributed than yttrium. A peralkaline granite gneiss phase of the complex intrudes the syenite gneiss and possibly truncates it, and the mineralization, near the southern boundary of the mineralized zone.The mineralized zone is coincident with a radiometric anomaly and discontinuous yttrium and zirconium soil anomalies.More drilling and metallurgical studies will be required to determine the economic viability of the yttrium and zirconium mineralization at Kipawa."

Jan 1, 1992

By X. Cao, M. Xiao, M. Jahazi

Magnesium alloys have low hardness, wear, erosion and corrosion resistance. The repair of service-damaged aerospace components made of magnesium alloys is an attractive solution in terms of time and cost saving. The feasibility of applying laser beam technology to repair ZE41A-T5 magnesium alloy sand castings in the machined surface conditions was studied using a continuous wave 4 kW Nd:YAG laser system. The influence of process parameters such as laser power, cladding speed, wire feed rate and defocusing distance on the shape, size and area of single cladding beads is discussed using a process optimization software. Sound single clad beads with good geometric characteristics were obtained using strictly controlled laser process parameters. The overall results indicate that laser surface cladding using filler wire has the potential for repairing aerospace components made of cast magnesium alloys.

Jan 1, 2006

By R. C. Carne, R. J. Cathro

"Most of the recent large discoveries of zinc, lead and silver in Western Canada are Paleozoic-aged stratiform deposits that occur within the limits of the tectonic sub-province of the Canadian Cordillera known as Selwyn Basin. Bounded on either side by coeval carbonate platforms. Selwyn Basin trends northwest for 1300 km from northeast British Columbia to Alaska. Paleozoic rocks of Selwyn Basin consist primarily of chert, shale and coarser-grained clastic sedimentary rocks with minor volcanic rocks.The Selwyn Basin deposits have few counterparts elsewhere in Canada, but have a close similarity in geological setting, mineralogy and morphology to well-known deposits such as McArthur (HYC) in Australia, Meggen and Rammelsberg in West Germany, and Sullivan in British Columbia. Recent studies of these deposits have led to an emerging, but now generally accepted, model of ore deposition in which stratabound zinc-lead-silver shale-hosted or ""sedimentary-exhalative"" (sedex) deposits are precipitated in active tectonic environments from metalliferous geothermal brines that rise to the sea floor along deep-seated fault zones. Although their mineralogy and ore metal zoning can be similar to that of volcanogenic massive sulphide deposits, most sedex deposits have only a weak genetic link with volcanism.Sedex mineralization in Selwyn Basin has been identified within three separate ages of shale or its metamorphosed equivalent. The lower Cambrian-age Anvil Camp in central Yukon Territory contains the only producing mine (Faro). Important lower Silurian-age zinc-lead mineralization is at Howards Pass along the Yukon - Northwest Territories border. Barite and zinc-lead-barite mineralization of upper Devonian age occurs across Selwyn Basin. Potentially economic deposits have been found at Macmillan Pass, along the Yukon - Northwest Territories border and in the Gataga District of northeastern British Columbia."

Jan 1, 1982

By T. Rahimzadeh, C. W. Trueman, S. Farzaneh, S. V. Hoa, I. Abdalla

This paper presents the shielding effectiveness (SE) of woven continuous carbon/epoxy composite materials. The theoretical and physical concepts behind the experimental results are demonstrated in details. The influence of frequency, the overlapping angle between overlapped layers and the number of overlapped layers upon the EMI shielding of composite sheets are discussed. In this work, in particular, the epoxy layers are considered as dielectric apertures of the conducting carbon fiber slab for the interpretation of the experimental results. The experimental results, using ASTM standard D4935-89, indicate that the SE can reach values greater than 90 dB above 500 MHz.

Jan 1, 2006

By L. A. Clark, G. H. R. Burrill

"Most unconformity-type uranium deposits in Saskatchewan occur within a few tens of metres above and/or below the basal unconformity of the 1,45-b.y. Athabasca Sandstone. Graphitic basement rocks coincident with post-Athabasca faulting or brecciation at or near the unconformity are important in localizing uranium deposits which form as tabular, ribbon-like bodies with grades averaging over 2 per cent uranium and containing up to 50,000 tonnes UJOs. Some of these deposits have similar contents of nickel and arsenic.In the genetic model proposed to explain these deposits, traces of uranium were leached from the sandstone and weathered basement rocks by oxidized formation waters sweeping through the sandstone and along brecciated faults. Over basement meta-petites, a thick clay regolith adsorbed uranium from the solution. Thus fixed, the uranium was reduced through an indirect reaction with graphite, possibly involving methane. The clay mineral surfaces were thus continuously cleared to allow further adsorption. Basement faults localized along weak graphitic units were re-activated, offsetting the sandstone formation, probably at the time of an early uranium deposition about 1.2 b.y. ago, and served as vents for spent ore solutions. Fluid convection was induced by topographic relief and/or crustal heating from radioactive decay in basement plutons or mantled Archean domes with uranium and/or thorium contents a few ppm above those of adjacent rocks. Heat from radioactive decay within the incipient uranium deposit would develop in about a million years. The self-generating convection cell would continue uranium deposition until all permeability was plugged by minerals. In some instances, convection was re-initiated after subsequent faulting and brecciation. While some deposits were further enriched, heavy flows of oxidized fluids re-dissolved and partially depleted other uranium deposits.The East Alligator Rivers uranium deposits in Northern Territory, Australia, occur within Middle Proterozoic quartzchlorite and quartz-muscovite schists overlain by sandstone. Highest grades occur in silicified breccias where carbonate beds were leached out. Mineralization ages are both pre- and post-Kombolgie Sandstone, but, to date, no significant uranium mineralization has been encountered in the sandstone. There are many general similarities with Saskatchewan deposits, but important differences in detail."

Jan 1, 1981

By John De La Vergne, Morri Medd

"This paper describes the sinking of a circular concrete ventilation shaft through 110feet of water-bearing overburden. The brine circulation freezing method was used to stabilize the walls during excavation. In order to take advantage of the cold winter weather, a custom-built heat exchanger (natural radiator) was installed in place of the standard mechanical refrigeration plant.IntroductionIn the late fall of 1979, Les Mines Selbaie awarded a contract to the firm of 1.S. Redpath Limited to sink a ventilation shaft on its property in northwestern Quebec. The shaft was to be sunk through 110 feet of water-bearing overburden and approximately 90 feet of rock to a final depth of 200 feet below surface. The water table was measured at 16 feet below the surface elevation.After examining the soils report and diamond drill core from the shaft area, Redpath came to the conclusion that freezing was the best way to stabilize the overburden for sinking. LocationThe mine site is 420 statute miles due north of Toronto, just east of the Ontario/Quebec border (Fig. 1). Access to the site is provided by a development road built by the Quebec government from the Matagami/lames Bay Highway. History of Ground Freezing In the Mining IndustryIn 1862, shortly after the development of mechanical refrigeration, a mine shaft was sunk through an artificially frozen water-bearing formation in the United Kingdom. The first application of ground freezing in North America was for a Michigan iron ore shaft in 1888. Since that time, the freezing method has been used to sink hundreds of shafts throughout the world. Its best known application was to sink sixteen shafts through the Blairmore Formation in Saskatchewan.The same method has been used in every case. It involves chilling a calcium chloride brine solution and circulating the brine in concentric pipes, spaced between 3 and 6 feet around the shaft perimeter and usually 4 to 5 feet from the limits of the proposed shaft excavation."

Jan 1, 1982

By M. Fafard, D. Picard, J. -F. Bilodeau, G. Soucy

To simulate adequately the behaviour of a Hall-Heroult electrolysis cell, a finite element model must take into account the properties of each material. However, it has some lacking knowledge on the mechanical behaviour of materials, like the long-term visco-elastic (creep/relaxation) behaviour of cathode. A three-dimensional model is then proposed in this paper and will be ready to be implemented in the finite element code FESh++. The model was developed using the three-dimensional model based on thermodynamic of irreversible processes where the choice of the internal variables is based on a phenomenological approach. All parameters of the model are represented by constant constitutive tensors and the temperature and chemical dependencies are taking into account through scalar functions multiplying the constant constitutive tensor. The goal of the first part of this project was to determine the parameters of the threedimensional visco-elastic model at the reference state (virgin material at ambient temperature) of three different cathode materials. This paper presents the theoretical model and the results of creep tests at ambient temperature for the semi-graphitic carbon cathode.

Jan 1, 2006

By W. D. Fogwill, P. J. Clarke

"The Dawn Lake uranium deposits are located 340 km north of La Ronge, Saskatchewan, in the Athabasca Basin between the Midwest Lake and Rabbit Lake deposits. Four zones of uranium mineralization, called the ""11, 14, 11A and 11B Zones,"" lie within the Athabasca Sandstone, at the sub-Athabasca unconformity and in the basement.At Dawn Lake, approximately 100 metres of Helikian Athabasca Group clastic sediments overlie Aphebian Wollaston Group pelitic and calcareous metasediments and pegmatites. Uranium with some nickel, cobalt and copper, occurs near the sheared stratigraphic contact between calc-silicate gneiss and graphitic, pyritic pelite. The mineralization lies in an area of low magnetic susceptibility which is thought to represent a rock sequence lying stratigraphically high within the Wollaston Group. There is no obvious vertical displacement of the unconformity by faulting, despite considerable brecciation, shearing and slickensides seen in the basement rocks. This suggests horizontal displacement on steeply dipping wrench faults as the main tectonic control along the 11, 11A and 11B trend.Below the Athabasca unconformity, the Wollaston Group rocks are altered to fine-grained mixtures of clays, chlorite and silica commonly called regolith. Along the mineralized trend post-Athabasca fracturing and (or) compaction have occurred through this clay-rich alteration zone, causing the steeply-dipping primary foliation to become contorted. This ""crenulated"" horizon can reach depths of 35 metres below the unconformity and is thickest along fault zones in the calc-silicate rocks. The ""crenulite"" is a distinctive unit which at Dawn Lake is commonly found above pods of ore located deep below the unconformity.Much of the mineralization in the 11A and 11B Zones occurs above, beside and below the thickest part of the crenulated zone, although the crenulated rock itself contains negligible amounts of carbonate, pyrite and uranium. Intense vuggy alteration and collapse breccias are found in calc-silicate rocks deeper and to the west of the 11A and 11B mineralization. There are at least two ages of uranium deposition in the basement zones, shown by small bright cubes of ""pitchblende /"" overgrown and replaced by duller botryoidal ""pitchblende II. ""Sooty pitchblende and yellow secondary minerals are the result of still younger reworking.The geological setting of mineralization, along the contact between carbonate-rich calc-silicate rock and pyritic pelite, suggests that the uranium was concentrated at a pH/Eh boundary located between deeply weathered, carbonate-rich and sulphide-rich basement rocks."

Jan 1, 1986

By J. Dufour

Although the recovery of nitric and hydrofluoric acids from stainless steel pickle liquors has been solved by several methods, such as solvent extraction, acid retardation, evaporation or pyrohydrolysis, metals (mainly iron, chromium and nickel) are usually obtained as a waste or by-product that has to be disposed. Alternatively, the treatment requires a high liquor flow to be economical, as is the case for pyrohydrolysis. A new process has been developed for metals recovery, that produces metal oxides with a low fluoride content. This new technique is based on a selective precipitation mechanism, which produces nickel hydroxide with a purity of 90%, separate from a mixture of iron and chromium oxides and hydroxides suitable for recycling. The reaction mechanism is based on the precipitation of fluoride compounds of iron and chromium, K2FeF5 and CrF3. For this purpose, free fluoride must be added as potassium fluoride. Also, solid fluoride compounds are hydrolysed, releasing free fluoride. A part of the fluoride is recycled to the selective precipitation operation and the remainder is fed to the acid recovery stage. Nickel does not react in this operation; it remains in solution giving a high separation yield.

Jan 1, 2006

By C. Juers

Laboratory chromate coating was applied on AM50 and AZ91D alloys and compared to phosphate-permanganate one. Evaluation of the corrosion behaviour was performed using electrochemical DC and AC methods in ASTM water D1384-87. This electrolyte was chosen because it was moderately aggressive and found to give generally good correlations with long period exposure results in atmospheric conditions. Electrochemical impedance spectroscopy was used to determine more accurately the corrosion rates from the analyses of the high frequency capacitive loop. Anodic polarization was applied in order to evaluate the pitting resistance of the different coatings. These results were correlated with weight loss data evaluated from experiments performed by immersion tests in ASTM water D1384-87 and climatic cyclic chamber tests.

Jan 1, 2006