Search Documents

By D. Yamada, T. Tanaka, N. Inouchi, J. Nakahigashi, H. Yoshimura, T. Nonishi

The use of cereal food materials as lubricants was investigated in an attempt to develop nonpolluting lubricants. Suspensions of wheat flour in water and other types of cereal food lubricants were prepared and their friction coefficients measured. The results indicate that a cereal food lubricant containing 30% lipids, 2% proteins, 60% carbohydrates and 0.6% calcium carbonates has the lowest friction coefficient for a sheet (cpTi-1). As example applications, the lubricant was tested with a forming press and a screw-fastening device. In both applications the cereal food lubricant performed relatively well in comparison to conventional lubricants and thereby has potential for practical applications.

Jan 1, 2006

By F. Y. Hsiao, H. C. Kao

Underground excavation in hard rock is normally stable at shallow depth except for wedge failure. However, the excavation depth is rapidly increasing recently. In high overburden stress condition, the integrity of rock would be destroyed with degrading rock strength. Therefore, understanding both the peak and the post-peak strengths of hard rock are necessary to assess the tunnel stability at depths. The characteristic of the post-peak strength is seldom studied in Taiwan in the past. Various estimation methods for the post-peak strength degradation were briefly reviewed in the paper. Based on the Geological Strength Index (GSI) system is widely used in the determination of the rock mass strength, the quantitative residual GSI system was adopted to estimate the possible strength degradation for a hydraulic tunnel in Taiwan. The Mohr-Coulomb model (no strength degradation) and the post-peak strength degradation model (strain softening model) were used to simulate the excavation of the case tunnel at different depths. The analyses demonstrate that the tunnel is in stable condition at 600m of depth. And the effect of the postpeak strength degradation on tunnel deformation is progressively significant with increasing tunnel depth. Approximate 3-5 times of increase in crown settlement and horizontal convergence would occur when post-peak strength degradation are considered at 2400m of depth. Severe tunnel deformation may endanger the tunnel stability. Modeling results reveal that the post-peak strength degradation has a great effect on tunnel stability under high overburden stress condition, which should not neglect in deep tunnel design.

Jan 1, 2015

By A. Bhowmik

Uranium Refining is the process in which undesirable neutron absorbing elements such as Boron (B), Gadolinium (Gd), Cadmium (Cd), Europium (Eu), Samarium (Sm) and other heavy metals (Fe, Ni, Co, Ca, Mg etc.) are removed to make it nuclear pure. At present, Uranium refining is carried out by solvent extraction process by using organic based solvent e, g. TBP diluted with Kerosene. The above process generates lot of nitrate bearing liquid waste and degraded organic. In order to eliminate use of hazardous organic and ammonia for Uranium refining altogether, a new process has been developed. In the new process, Yellow Cake is dissolved in nitric acid and uranium peroxide hydrate is precipitated selectively from the solution leaving all the impurities in the solution by using commercial grade hydrogen peroxide at a pre-defined pH, U conc., temperature and stoichiometric quantity of hydrogen peroxide under mild agitation. The precipitate is filtered and washed with DM water to obtain nuclear pure product meeting purity standard as per ASTM C ? 753-99.The product is spray dried and calcined to obtain uranium oxide. The process eliminates use of organic, flammable, toxic chemicals, consumes less quantity of nitric acid and uses environfriendly chemical hydrogen peroxide. The process is simple and can be integrated in the mill. A patent application is entering national phase in several countries including CANADA and abstract/full paper is available in WIPO publication no: WO/2009/013759.

Aug 1, 2010

By M. Côté, H. Pépin, Y. Richer, C. Gingras

Rolls-Royce Canada has been nominated as a Rolls-Royce Center of Excellence for repair of fan blades in 2003. One of the challenges of the Rolls-Royce Canada Component Repair Center of Excellence team is to reduce cost and time of inspection while ensuring trace ability and quality of the inspection performed on the fan blades. In the context of the dimensional control process optimization, and following the positive conclusions of initial trials carried out in 2003, the technical authorities at RRC have selected the SPG data 3D(TM) technology as a development base for dimensional control programs. The main goal of this development initiative is to develop and support an inspection system to perform the dimensional control and inspection of different components at the Montreal Fan Blade Repair Center of Excellence. The final objective of the program is to build a server platform capable to support different inspection sites within the Montreal facility for the future. This paper presents the certification process of the technology according to the VDI-VDE 2633 certification standards and some results of the fan blade inspection program of the BR 710, BR 715 and TAY according to the JES 195 engineering standards specification.

Jan 1, 2006

By R. H. Keyes Duval

"The one point left off the table was pumping costs, i.e. the cost of pumping to the cyclones.At East Malartic 5 x 5 S R L pumps that had been used to pump the classifier overflow were used to pump the rod and ball mill discharges to the cyclones. Maintenance costs on the pumps rose from $105 in 6 months to $1000 per month. The pumps had to be operated at 1150 rpm and impellers lasted only 5 to 6 days. These pumps were replaced by 6 x 6 S R. L. pumps operating at 825 rpm, but at this speed the coarser sands settled and plugged the pipe lines and the speed was increased to 925 rpm. The maintenance cost is now $100 per m::rnth which is 0 003 cents per ton milled. The impellers now last 1 month and the casing linings 6 months.Density meters are often used on cyclone overflows and sometimes on the cyclone feed. Haliburton weighted tube density meters are used in some plants. They are cheaper than the radioactive density controller, $2500 as compared to $ 6000The angle of the discharge spray from the apex can be used to judge the quality of perform1nce of a cyclone.For ordinary metallurgical applications the inside slope of the cyclone is not too important but for fine separation steeper slopes are used.The cyclone is a versatile tool and will handle considerable variations in feed tonnage - probably up to 15%. Above this variation the number of cyclones used has to be increased or decreased or the tonnage fed to them has to be adjusted"

Jan 1, 1965

By S. Rash Ahmadi

Welding is highly reliable and efficient metal joining process. In welding the metal adjacent to the weld joint is subjected to severe thermal conditions. As a result, complex changes in metallurgical structure occur in this region. These changes in structure depend on the material and the temperature history experienced. Friction stir welding (FSW) is relatively a new welding process in which, heat is generated by friction between the tool and the workpiece. The amount of heat conducted into the workpiece determines the quality of weld, residual stress and distortion of the workpiece. The objective of the current work is to study the transient temperature in a friction stir welding. So, a three dimensional transient analytical model is used to study the thermal distribution during the welding. Heat input from the tool shoulder alone is considered in the model. The process parameters like axial load, welding speed and tool rotational speed, used in actual FSW process are taken to build the model. This analytical model is very useful for select the optimized affected parameters in friction stir welding. The model illustrates the comprehensive equation including actual affected parameters in FSW and it can be used for different materials. In addition to the above the thermal history finds application in design of welding tools.

Oct 1, 2011

By Donald S. Macdonald

"I AM thankful for this opportunity to address the Toronto Branch of The Canadian Institute of Mining and Metallurgy. The Members of your Institute can have a great influence on the direction in which the mineral policies of Canada will evolve, and to assure that optimum benefits from our country's vast mineral resources will accrue to the nation as a whole and to all its citizens. Today, I want to: (1) offer an outlook on the mineral industry for 1973; (2) talk briefly about the role of minerals in the total economy; and (3) outline some of our thinking with respect to a national minerals policy for Canada."

Jan 1, 1973

By S. A. Sadough vanini

In this paper, Stress-Strain-Temperature relations for Shape Memory Alloys are studied. Temperature effects on Shape Memory Alloys are different from those related to ordinary materials. In ordinary materials, elastic characteristics can be assumed to be constant in low temperature ranges, and only the deflection arising from temperature changes could be added to the elastic defection. As long as two phases of austenite and martensite could be present in Shape Memory Alloys simultaneously, elastic modulus follows temperature and temperature gradient. In continue a smart actuator is investigated considering a homogeneous cantilever beam. Beam bending is established by using shape memory wires. An initial strain is imposed to shape memory wires in a low temperature, and then, they are installed in the outer surface of the beam. Therefore, since the temperature is imposed in these wires and they cannot have free recovery strain, the compressive recovery stress will be produced in the outer surface. This will result in a deflection in axial direction of the beam. At first, beam deflection is calculated on the basis of theoretical relations and solving the relevant differential equations. Afterwards, experimental tests are performed on an elastomeric beam equipped with shape memory wires. When a voltage is applied, a temperature rise will occur in the wires; then, this temperature rise causes a deflection in the beam. Finally, the theoretical and experimental results? comparison indicates a good conformity. One capability of this actuator is its high flexibility, and by controlling the inlet current, the end-beam deflection can be controlled.

Oct 1, 2011

By Sadough vanini Ali

Charpy impact energy of functionally graded steels produced by electroslag remelting in crack divider configuration has been modeled in various strain rates. It has been well known that majority of materials indicate different behaviors under different strain rates and temperatures. Therefore, modifying the elastic-plastic model considering the effects of strain rates and temperature gives us an acceptable prediction of these composites behaviors in impact test. In this investigation, graded steel was divided in to several layers in which the layers have the same strains under the impact. Constitutive equation describing the flow stress variations as a function of strain rates and temperatures, have been used to express the stressstrain behavior of layers. The parameter values of constitutive equation determined for all the layers via using the boundary conditions based on composite graded behaviors which were the characterized ferrite, austenite, bainite and martensitte phases. Consequently by applying the rule of phase mixtures and ascribing the impact energy of each layer to the area of stress-strain curve of the same layer, the whole impact energy of composite is the sum of layers impact energy with considering the layers volume fraction.

Oct 1, 2011

By Barton G. Stone

The mining and exploration industries have been using Geostatistics (Matheron, 1963) for the past forty years. It has been extensively incorporated into three dimensional block modeling software whose usage has reflected the growth in the use of personal computers since 1980. Because of the utility of geostatistical models in mining and production planning, much of the modern reserve and resource modeling is done by mining engineers, geostatisticians and geological engineers. Explorationists are initially less concerned with three dimensional models until such time as a deposit has been roughly delineated. However, the concept of regionalized variables in ore deposits deals with the effect of spatial correlations between data points in a three dimensional sample space and should be useful for optimizing the spacing of drill holes to allow maximum bang-for-the-buck in drilling programs. This paper examines three common deposit types (porphyry copper, VMS and intrusive gold) to examine whether geostatistical methods have been used to minimize drilling costs because of better understanding of spatial correlations. The three model types were chosen from publicly available corporate websites of Canadian based Junior Mining Companies. They include the Wolverine polymetallic zinc deposit of Yukon Zinc in Yukon, Canada; the El Morro Deposit in Chile (30 percent ownership by New Gold Mining Company, and the Fort Knox Gold deposit in Alaska and 50 percent ownership by Nova Gold Resources). Typically, individual mining corporations post their technical reports as CNI 43-101 reports on their corporate website as indications of the favorability or progress on their more exciting properties. Data considered for this paper was not collected or generated by the author, but the information was extracted from these publicly available sites and had a variety of authorship.

Oct 1, 2009

By M. T. Shehata, R. W. Revie, M. Elboujdaini

Environmentally assisted cracks in linepipe steels are initiated either as a result of stresses in combination with environmental effects, as in stress corrosion cracking (SCC), or as a result of trapped hydrogen in the steel, as in hydrogen-induced cracking (HIC). To understand better the mechanism of the crack initiation process, key metallurgical and environmental elements that can affect the cracking phenomena were investigated and are reviewed in this paper. The complexity of both cracking phenomena results from the dependence of SCC and HIC on multiple metallurgical, mechanical, and environmental parameters that may all influence both crack initiation and propagation; e.g., composition, microstructure and non-metallic inclusions in the steel, applied stress, water chemistry in the field, and ionic concentrations in the groundwater near the pipe surface to name a few for SCC. In addition, for HIC phenomena, one can add the concentration of H2S in the fluids transported in the pipe as well as concentration of CO2, pH, etc. In this paper, cracking of linepipe steels is analyzed critically, with particular attention to the crack initiation process. The paper is divided into two parts: The first part covers SCC and the second covers HIC.

Jan 1, 2005

By A Sadough Vanini

In this paper large deformation of smart functionally graded beams with initial imperfection and under thermal loadings is considered. Smart beam consist of two types of layers. One layer is made from functionally graded materials and a layer or a set of layers from active materials that usually is made from piezoelectric materials that are bounded on the surfaces of beam. An active controller is used for controlling the deformation and stress in functionally graded layer of beam. A simple Euler- Bernoulli beam theory is used for analyzing of beam. In functionally graded layer the material property vary continuously through the thickness direction and power law model is used for the variation of elastic modulus, heat expansion and heat conduction coefficients. Poisson ratio is assumed to be constant in functionally graded layer. The effects of varying the power law constants and the Gain of controller is considered here. The results are reduced and compared with smart functionally graded beam without initial imperfections.

Oct 1, 2011

By Elizabeth Edwards, Radhakrishnan Mahadevan, Vladimiros G. Papangelakis, Srinath Garg, Kurtis Judd

Mineralogical characterization of the tailings showed the deportment of Ni to be similar in the Vale and Glencore tailings, with 60% of the total Ni locked in pyrrhotite, and the balance 40% associated with pentlandite. The overall Ni dissolution was correlated with the individual dissolution extents of pyrrhotite and pentlandite as functions of four leaching regimes: ‘anoxic acid’ (with and without pH control), ‘oxic acid’ (oxygen sparging), ‘oxic acid’ (air sparging), and ‘oxic ferric’ (air sparging). The results showed that the maximum Ni dissolution was obtained during the pH controlled oxic acid leach with oxygen sparging at pH 1.5, while the anoxic acid leach at pH 1.5 resulted in minimum Ni dissolution (10–15%) from pyrrhotite. An overall Ni mass balance showed that pyrrhotite and pentlandite dissolve simultaneously in the presence of Fe(III) and oxygen, in contrast to the preferential dissolution of pyrrhotite in the absence of Fe(III). Sulphur mass balances revealed that the yield of elemental sulphur is maximized (65%) during the oxic Fe(III) leach at pH 0.6. Furthermore, the kinetics of Ni leaching and elemental sulphur formation from pyrrhotite tailings leached with ferric sulphate between 55–80°C was investigated at constant oxidation-reduction potential. Elemental sulphur yield increased with increasing temperature, but no observable trend could be linked to ferric or ferrous ion concentration.

Jan 1, 2017

By R. Gutray, J. E. Grainger

This paper deals with the use of a cement-deslimed mill tailings mixture for a scraping floor in cut-and-fill stopes at Madsen Red Lake Gold Mines Limited. It describes the mixing and placing procedures and the precautions used with respect to the floor while mining in the stopes. Details of the mix are presented, and advantages and disadvantages discussed. The paper concludes with a brief outline of the costs.

Jan 1, 1966

By J. Starkey

A comminution circuit in recent history, is one of the most difficult parts of a mineral processing plant to design with confidence. It is usually the most costly part of a plant to build, and it can consume up to half or more of the energy used on a mine site. To suggest that comminution energy usage is sustainable in the long term is not possible at this time. What we have to choose from today, based on more than 50 years of experience, does include the best available technology, and the best way to design it. There is controversy in the industry as to how to properly approach the subject of comminution design, with many of the optional solutions requiring a level of training and expertise beyond the ability of a non-specialist engineer. Semi-autogenous grinding technology in particular, has not been properly appreciated because of many recent mistakes in its application and design, which have blurred the positive perception about what SAG technology is, how it can be used, and how it needs to be designed and built. In order to change this, mine owners and senior managers need to take responsibility for, and learn to understand the fundamental challenges that a comminution circuit poses to the project, to the design process, to the operators who use the equipment, and to the resulting metallurgy. This address is intended to summarize these challenges and offer fundamental engineering solutions, which are clear, specific and in a format which is directly applicable to the mining and mineral engineering community.

Jan 1, 2018

By J. E. Dutrizac

Mercury balances have been obtained for the flotation circuits at Pamour Porcupine Mines, Timmins, Ontario, and at Brunswick Mining and Smelting Corporation, Bathurst, New Brunswick. The mineral form of mercury in both deposits has been ascertained. At Pamour Porcupine, the mercury is approximately evenly divided among sphalerite, native silverelectrum and tetrahedrite-tennantite; at Brunswick Mining, this element is contained mostly in the sphalerite, although tetrahedrite (and possibly pyrite) also contains minor quantities.

Jan 1, 1979

By M. Maeda, H. Sasaki

"Precious metals such as platinum, palladium, and rhodium are commonly used for automotive catalyst converters. To recover these metals with lower environmental load and cost, exposure to zinc vapor was proposed as a pretreatment prior to acid leaching. Alloying with zinc is expected to enhance dissolution of precious metals and reduce the amount of toxic chemical agents required for the leaching. This study examined the effect of the alloying pretreatment using model catalysts. Catalysts were immersed in leaching solutions for a predefined time with or without zinc vapor pretreatment, and the amount of dissolved metals was then evaluated. INTRODUCTIONAutomotive catalysts account for large portions of the world consumption of platinum (Pt), palladium (Pd), and rhodium (Rh) (Butler, J., 2011). Because of their limited production and high prices, recovery of the precious metals from spent catalysts is obviously an important issue. A representative structure of an automotive catalytic converter can be described as a monolithic ceramic support with a honeycomb structure which is coated with porous oxides such as those of aluminum (Al2O3), cerium (CeO2), and zirconium (ZrO2) (Heck & Farrauto, 2001; Matsumoto & Shinjoh, 2007). Small particles of precious metals, originally several nanometers or less, adhere to the oxides.Typical recovery processes for precious metals from scraps are shown in Figure 1 (a)-(c) (Habashi, 1997; Yoo, 1998; Shibata & Okuda, 2002). Precious metals can be recovered by using non-ferrous smelters as Figure 1 (a) shows. Smelted along with metals such as copper (Cu), precious metals and ceramics in the scraps are absorbed into the metal phase and slag phase, respectively. Because the metals separate from Cu as anode slime in successive electro-refining, such a process can recover precious metals as co-products of Cu. However, in order to prevent negative effects on the principal process, a specialized procedure is needed. Figure 1 (b) is a specialized approach in which scraps are melted at elevated temperature with Cu called the Rose process. Here Cu works as a collector metal, and the absorbed precious metals are then concentrated by oxidation of Cu. Such a process can separate precious metals from ceramics constituting catalyst converters. Smelting at high temperature, however, requires extensive equipment as well as a high amount of energy. On the other hand, hydrometallurgical processes may be effective to separate precious metals from ceramics into an aqueous solution, because chemical agents can act on these metals selectively (Figure 1 (c)). Leaching of precious metals, however, requires strong acid and oxidizing agents because of their corrosion resistance; this makes liquid waste disposal and the large environmental load controversial. To solve the problem, a metal vapor pretreatment was proposed (Okabe, Yamamoto, Kayanuma, & Maeda, 2003a, 2003b; Kayanuma, Okabe, Mitsuda, & Maeda., 2004; Kayanuma, Okabe, & Maeda, 2004; Itoh, Kayanuma, Miyake, Kimura, & Maeda, 2005). A flow diagram of the process using zinc (Zn) vapor is shown by Fig. 1(d). Exposed to Zn vapor, precious metals are expected to form alloys which dissolve more easily than pure precious metals, thus reducing the use of chemical agents and environmental load involved with successive leaching. In previous research (Sasaki, Miyaki, & Maeda, 2010; Sasaki & Maeda, 2010, 2012), dissolutions of precious metal alloys formed by Zn vapor treatment were examined in hydrochloric acid (HCl) using an electrochemical method, and it was confirmed that these metals dissolved at higher rates from the alloys than from their pure states (Figure 2). In this study, the availability of the alloying pretreatment was demonstrated by testing on model catalysts in leaching solutions."

Jan 1, 2012

By J. K. Gowans

The Research and Design group of the Project Development Division (PDD) of Placer Dome Inc. includes metallurgical, electrical, civil and mechanical engineers. They provide metallurgical research and conceptual flowsheet development, feasibility concepts for the processing and ancillary facilities, and manage the detailed design of the facilities once approval has been given to a mining project. This paper describes how this group works, within the Project Development Division, to help develop feasibility studies with the Evaluations Group, manage detailed design, and provide support for the Construction Group. The paper briefly reviews the history and growth of the group and describes how it is evolving. The role of outside engineering firms and how they are incorporated into the division’s objectives are also discussed. The paper highlights the differences between Placer Dome’s Project Development Division and other mining groups, and why this approach fits the way Placer Dome does business.

Jan 1, 1998

By John S. Stevenson

THE Twin "J" Mine, operated by Twin "J" Mines, Limited, represents an amalgamation of the old Lenora, Tyee, and Richard III mines (see Figure 1) on mount Sicker, eight miles by road, northwesterly, from the city of Duncan, on Vancouver island. These mines produced 253,000 tons of copper-gold ore between 1898 and 1909 (see Table I). During the more recent period of production from these properties, July, 1943, to May, 1944, Twin ?J? Mines, Limited, mined and milled ore with values mainly in copper and zinc, and minor values in gold, silver, and lead. Figures are not available for this later production. Field work at the property was started by the writer in 1941 and continued in 1943 and 1944.

Jan 1, 1945

By A. I. A. Salama, M. W. Mikhail, R. J. Mikula

"The Coal Research Laboratory (CRL) of CANMET along with other research organizations in coal-producing countries envisage major benefits from computer applications in coal preparation, Some of these benefits are greater system flexibility, improved coal preparation plant performance efficiency and efficient utilization of manpower, all of which result in economic benefits. Computers can be applied for both on-line and off-line purposes; this paper focuses on the on-line applications from the process control point of view.A critical discussion of the different analog and digital process control systems is presented. Recent developments in Great Britain, West Germany, Poland and Australia on automation and instrumentation using on-line measurements of coal ash and moisture contents are identified.The CRL research and development strategy aimed at achieving on-line computer control of an automated coal preparation plant is presented.IntroductionIn the past twenty years an enormous progress in the area of computer technology has been noticed. Computer applications in industrial processes offer greater system flexibility, improved plant performance efficiency and efficient utilization of manpower. Significant computer control development in mineral processing has already been achieved. Although progress has been made in the area of computer applications in coal preparation, more effort is needed to utilize the full potential.The computer applications in coal preparation can be viewed as off-line and on-line. Considerable progress has been reported in the area of off-line computer applications, especially in the areas of modelling, performance evaluation/prediction and statistical analysis. However, only modest progress in on-line applications has been reported(1-7). This paper will focus on: online instrumentation and process control applications, different analog and/or digital control systems, on-line automation and instrumentation in other countries and CRL strategy toward pilot plant automation."

Jan 1, 1985