Search Documents

By E. Herrera, L. Mariscal

"Ilo Copper Smelter operates since 2007 with an ISASMELTTM furnace as a single smelting unit (1,200,000 tpy) associated with two Rotary Holding Furnaces for separation of matte and slag, and which directly produces a discard slag. Southern Peru continually has been improving the slag chemistry of its ISASMELTTM furnace in order to reduce copper losses, given its big economic impact due to large slag mass generation. The present paper describes the influence of the CaO, Al2O3 and magnetite content in the slag of the ISASMELTTM furnace correlated with the SiO2/Fe ratio and its liquidus slag. Also it defines the best slag chemistry and operating practice in order to reduce the copper losses without compromise the bricks life of the furnace.INTRODUCTIONIlo Copper Smelter of Southern Peru (Grupo Mexico) is located on the southern coast of Peru, and treats mainly copper concentrates produced in its own mines (Toquepala and Cuajone).The modernized smelter was commissioned in 2007 and operates with an ISASMELT™ furnace as a single smelting unit (1,200,000 tpy), which is associated with two Rotary Holding Furnaces (RHF) for separation of matte and slag. This slag is directly sent to the dump. Figure 1 shows the smelter flow diagram.The ISASMELT™ process is a bath-smelting process using a single lance. The lance tip is immersed into a molten slag bath contained within the stationary, vertical, refractory-lined ISASMELT™ furnace. The injection of oxygen-enriched air, through the lance into the slag results in a highly turbulent molten bath. Feed material falling into the turbulent bath from above reacts rapidly, resulting in extremely high productivity for a relatively small bath volume."

Jan 1, 2012

By Frank Ebbutt

Introduction The property of the Britannia Mining and Smelting Company, Limited, is situated on the east side of Howe sound, about six miles from its head. It is roughly thirty miles by water from Vancouver, one of the important ports of the Pacific and the industrial and financial centre of British Columbia. Howe sound is navigable for ocean-going vessels and Britannia Beach is a daily port of call for the commodious boats of the Union Steam-ship Company, sailing from Vancouver. Few mines are so ideally situated or have so many or varied natural advantages. Copper was first found on Britannia mountain in 1888, by Forbes, but it was not until 1898 that five claims were staked here by Oliver Furry, a trapper. It is from these claims that the major production during the past thirty years has come. In 1900 the Britannia Copper Syndicate was formed and development of the property was commenced. In 1903 the late Grant B. Schley obtained control, and through his efforts the Britannia Mining and Smelting Company was organized in 1908 as a subsidiary of the Howe Sound Company. Since that time, a persistent and progressive policy has been followed, which has resulted in a prolonged and profitable operation. The country in the immediate vicinity of the mine is marked by strong relief, with mountains rising abruptly from tide-water to elevations of 5,000 feet and more. Two broad transverse valleys deeply dissect the area. These are the valleys of Britannia creek and Furry creek. The region has under-gone prolonged and relatively recent glaciation. Over much of the surface there is deep overburden and dense vegetation. The geology of the mine and vicinity has been described in reports by S. J. Schofield (1), H. T. James (2), J. G. Barry, and others (3). The present writer is in accord with much of this literature on Britannia, but during recent years, extended observations made underground have shown that the 'quartz porphyry', or 'mine porphyry', of several of the earlier writers is not the host rock to the commercial mineralization; and he contends that the mineralization occurs in highly altered phases of a complex series of ruffs, flows, and pyroclastics and their autoclastic metamorphosed products.

Jan 1, 1935

By F. J. West

This paper deals with Jones & Laughlin Steel Corporation's new Adams mine, near Kirkland Lake, Ontario. After a brief discussion of ore structure, type, reserve tonnages, etc., the main body of the paper discusses the establishment of an open-pit limit based on economic considerations. The method used by J & L to arrive at an economically sound open-pit boundary its outlined fully. Physical limitations to open-pit boundaries are mentioned briefly. The paper concludes with a few remarks on the mining equipment in use and on its productivity

Jan 1, 1966

By Kai Zhang, Aijun Huang, Jeremy H. Rao, Xinhua Wu, Paul Rometsch

"As one of the most typical additive manufacturing (AM) technologies, selective laser melting (SLM) removes many of the shape restrictions that limit materials design, thereby allowing computationally optimised and high performance structures to be directly produced and tested. Due to the high reflectivity and lower absorptivity of Al alloy A357 powder during high temperature laser melting, one of the issues SLM might bring is the surface roughness and defects present on the parts. In this regard, this study investigates the surface roughness – fatigue property relationship for a heat-treated aluminium alloy A357 after SLM. Via the adjustment of SLM parameters, an ultrafine microstructure can be obtained due to the fast solidification rate. Therefore, comparable or even better mechanical properties can be achieved with respect to traditional A357 casting counterparts. Meanwhile, the surface roughness conditions of the SLMed Al alloy are also influenced by various processing parameters, raw powder properties, and sample building methods. For selective laser melted Al alloy A357 specimens, a dense part with a smoother surface would be expected to correspond with a good fatigue performance.INTRODUCTION Additive Manufacturing (AM), also known as 3D printing, is a process in which a complex part is fabricated layer by layer from a digital design package (Martin et al., 2017). AM has the potential to conserve raw materials, reduce the energy consumption, part cost, and fabrication time. Furthermore, as a typical additive manufacturing (AM) process, selective laser melting (SLM) was originally developed from selective laser sintering (SLS) based on higher quality lasers (Rao, Zhang, Fang, Chen, Wu, & Davies, 2017b). Different from conventional casting consuming valuable time and energy, SLM is now used as a cost effective method for the manufacturing of metals, such as Al-Si alloys, to produce almost full density parts using fine metallic powder and high power laser beam (Tang & Pistorius, 2017)."

Jan 1, 2018

By A. C. Halferdahl

The Granby ores may be divided into three groups or classes. The No. I ore is a heavy pyrite, chalcopyrite, pyrrhotite, sulphide carrying some free silica, and calcite. No. 2 ore carries the same general group of sulphides as does No. 1, but in a lesser amount. The gangue is an altered greenstone. No. 3 ore has a smaller amount of sulphides than either of the others. Analyses of these ores is as follows: Cu. Si02 Fe. CaO S. Al 203 MgO No. I. Per Cent. 1.8 17.5 33.0 5.7 34.5 2.3 1.3 No. 2 Per cent. 2. 0 35. 6 23. 9 4. 3 I .5. 0 9. 2 6 .. 0 No. 3, Per cent. 1 . 5 40. 9 21 . 7 3. 0 I 1 . 3 11 . 0 5 . 4 The sulphide minerals in No. 2 and No. 3 ores occur largely in bands in the gangue, and for these portions comparatively coarse grinding serves to release the gangue. Drill cores show a certain dissemination of sulphides in portions of the rock, so that grinding to 5 per cent. + 65 mesh with 65 per cent.-200 mesh liberates the sulphide minerals very completely. The association of the sulphides is fundamental. The pyrite was probably deposited first and was followed by a portion of the chalcopyrite, or these two portions of the sulphide minerals were deposited together.

Jan 1, 1924

By Peter S. Jack

"IntroductionTHE ORES treated at the concentrator of the Britannia Mining and Smelting Company, Limited, Britannia Beach, B.C., have always contained some lead, but it was not until 1950 that the combination of lead headings and lead price was such that recovery of this metal at Britannia became worthwhile. In that year, with the mining of a new orebody, the lead in the mill feed was raised from 0.07 per cent to 0.15 per cent. Chalcopyrite, sphalerite, and pyrite concentrates are produced by flotation at Britannia, •and 95 per cent of the lead in the mill feed reports with the chalcopyrite concentrate, so that the rise in lead headings was reflected almost wholly in the lead content of the copper concentrate. In 1950, investigation was started to determine if some of this lead could be recovered economically."

Jan 1, 1953

By Michael L. Wayman

Native copper is copper which exists in nature in elemental, metallic form, rather than being chemically combined as is the case with the more usual oxides, sulphides, carbonates, etc. Several other metals, including gold, silver and platinum also occur in native form as do, rarely, iron, lead and mercury; a few naturally occurring native metal alloys, notably electrum (gold-silver) and tumbaga {gold-copper or gold-silver-copper) are also known. An analysis of the relative availabilities of native metals as nuggets in a useful size range111 shows native copper to be by far the most abundant of the native metals, exceeding both gold and silver by at least two orders of magnitude. While such an estimate is crude, it serves to illustrate why copper was one of the first metals to have been used by ancient peoples. Native copper is known to occur on all inhabited continents, although its exact occurrence and abundance in ancient times cannot be unambiguously determined because many surface deposits may have been totally exploited and are therefore no longer identifiable. It is clear, however, that native copper does or did occur in all areas inhabited by the early metal-using cultures, for example in the Andes, in Central America and in the Near East. It is remarkable that most of the world's native copper occurs in the deposits of the Lake Superior region, primarily on the Keweenaw Peninsula of northern Michigan and on Isle Royale, an island in Lake Superior some 50 miles north of the Keweenaw deposits. Canadian deposits of native copper are found in Newfoundland and Labrador, Nova Scotia, Quebec, Ontario, British Columbia, the Yukon and the Northwest Territories (on Victoria Island, Bathurst Inlet and the Coppermine River area). It was to locate the latter deposits that the explorer Samuel Hearne was sent overland from Hudson's Bay in 1770; they were also surveyed by Sir John Franklin's expeditions in the 1820s.

Jan 1, 1999

By D. G. Cerigo, D. M. Bryce, P. H. Jennings

This paper summarizes the results of an experimental and economic study undertaken to evaluate the feasibility of treating an oxidized orebody of about 10 million tons, grading about 0.75 per cent copper, by agitation leaching and by percolation leaching.

Jan 1, 1968

By M. S. Hedley

"The Lucky Jim mine is at Zincton in Slocan mmmg division; on the Kaslo-Nakusp branch of the Canadian Pacific railway. It is owned and operated by Zincton Mines; Limited; a subsidiary of Sheep Creek Gold Mines; Limited. The mine is far in the lead in the production of zinc in the Slocan. Its recorded production from concentrates and shipping ore was 102; 260; 191 pounds of zinc to the end of 1945.GENERAL GEOLOGY With the exception of acidic dykes the rocks near the Lucky Jim mine belong to the Slocan series, which is Triassic in age and consists principally of argillaceous rocks. It disconformably overlies greenstones of the Triassic Kaslo series about 3 miles to the northeast, and is cut by granitic rocks of the Nelson batholith 5 miles to the southeast.The sedimentary rocks in this area are best referred to on the whole as slates. They lie within the more fissile basal part of the Slocan series. The term 'slate belt' conveniently distinguishes this area of rocks characterized by slaty cleavage from the more massive argillites that are more characteristic of the Slocan as a whole. The contact between the slaty and massive argillites lies ½ mile southwest of the mine."

Jan 1, 1954

By Victor F. Hollister

Elemental sulphur occurs as aformational sedimentary deposit in Upper Devonian Wabamun evaporites near Coronation, Alberta. The deposit developed in a stratigraphic jacies-change lrap; it is assumed that petroleum reacted with anhydrite to form sulphur, calcite, hydrogen sulphide and other reaction products. The deposit contains about 362,800 tonnes of sulphur and lies at a depth of 1200 m. The Coronation deposit is expected to be geologically typical of such other native sulphur deposits as may be found in Wabamun Group sediments. Widespread sour gas sulphur production f rom the Wabamun suggests the possibility that additional native sulphur deposits will ·be found.

Jan 1, 1984

By Andrew J. Freyman, Graham T. Armstrong

"In September, 1968, a survey of operating mines in the Yukon and the Northwest Territories was undertaken to determine the role of Indigenes (Indian, Metis, Eskimo) on the mines, and the attitude of mine management to these employees. The operating mines in the Territories had (at that date) a total employment of 2,002 men, of which 91 (4.5 per cent) were Indigenes. Indigenes make up 45 per cent of the Territorial population (18 per cent in the Yukon and 63 percent in the Northwest Territories). The paper documents some of the problems associated with indigenous employment in mines. A study was undertaken to determine the role of Indigenes (Indians, Metis, Eskimos) in operating mines in the Yukon and in the North-west Territories. In addition to the mines north of the 60th parallel, the experience of several other Canadian mines was examined. The general picture obtained is considered to be representative of the Canadian mining industry."

Jan 1, 1969

By M. Behrouz

Thermal power plants convert thermal energy due to nuclear reactions or the combustion of coal, gas, heavy oil, or some other hydrocarbon to electrical energy. They consist of a variety of equipment, such as boilers, turbines, generators, cooling towers, and auxiliary equipment. Any factor that affects the equipment efficiency affects the overall efficiency. Analysis of the cooling tower and raw water using the Langlier Saturation and Ryznar Stability Indices showed that the cooling water at Sarchesmeh was slightly scaling with respect to silica. Cold lime softening was found to be a cost-effective method to produce cooling water with adequate properties to reduce the cooling water make up from 85 to 70 m3/h and blow down rate from 35 to 20 m3/h.

Jan 1, 2007

By B. Burke

Magnesium and its alloys are attractive materials for use in automotive and aerospace applications because of the low density and good mechanical properties. However, difficulty in forming magnesium and the limited number of available commercial alloys limit their use. The present paper reviews the efforts to improve the attractiveness of magnesium through non-traditional processing, and presents preliminary results of current work on producing magnesium alloys via powder metallurgy P/M. P/M can be used to alleviate the formability problem through near-net-shape processing, and also allows unique chemical compositions that can lead to new alloys with novel properties. The feasibility of producing magnesium powder metallurgy products utilizing the industrially dominant process of mixed powder blending, uniaxial die compaction and controlled atmosphere sintering was investigated. An alloy composition based on the commercial Mg alloy AZ31 (3% Al, 1% Zn) was used to facilitate comparison to similar wrought products. The optimal processing conditions (compaction pressure, sintering time and temperature, and quenching temperature) were found to maximize sintered density and mechanical properties.

Jan 1, 2007

By I. M. M. W. R. Jones

"THE OBJECT of these notes is to initiate a discussion among the members of our Institution on the connotation of the term 'ore', and to arrive, if possible, at an acceptable definition of the term in the light of its current use by our leading mining engineers, metallurgists, •and geologists.The majority of •authors of well-known modern text-books on subjects dealing with mineral deposits define 'ore' in words which convey the meaning that it is an aggregate of minerals from which one or more metals can, under favourable conditions, be extracted profitably.Many eminent members of the Institution, and of mining and metallurgical institutions in other countries, consider that the term should not be restricted to metalliferous mineral •deposits but can also be applied correctly to certain non-metallic deposits. They believe that the growth, during the twentieth century, in the industrial importance of non-metallic minerals, and the progress made in the mining and the milling of deposits containing such minerals by methods similar to those used for metalliferous mineral deposits, no longer justify the academic restriction of the term to deposits worked for their metal content only."

Jan 1, 1954

By A F. Kravic

Carbonyl nickel powders of irregular particle shape and low a11parent density are used extensively in the production of porous nickel electrodes for nickel-cadmium storage batteries and hydrogen-oxygen fuel cells employing alkaline electrolytes. Such porous nickel matrices are at-tractive for these intended applications as they are relatively inexpensive, are corrosion resistant, have good electrical conductivity, can be welded to form electrical contacts, have a long life (as demonstrated in alkaline storage batteries), and are rugged and vibration and shock resistant. This paper describes a feasibility study concerning the production of porous multi-layer nickel electrodes by the pressing and sintering of stacked layers of green-powder rolled nickel sheet. Background H AUSNER (1) conveniently listed nine different powder compaction processes used for forming metal powders into useful shapes. These are shown in Table I. There are additional powder metallurgy processes; however, most of these are combinations of two or more processes listed in the Table. A study of the literature revealed that every powder compacting process, with the exception of isostatic pressing and explosive forming, has been evaluated or is being used for the manufacture of porous metal electrodes.

Jan 1, 1965

By Jeonghwan Kim

Intelligent Excavation System (IES) has been considered to be one of the desirable solutions to improve the productivity, quality and safety of the current earthwork processes. IES is composed of various hardware and software modules including task planner (work command generator), local and global work environment sensors, GPS and other sensors to acquire the excavator?s status, robotic controller and electronic valves, and the manipulator (excavator). A data communication manager was required to coordinate the signal or data-flow in between these modules considering the operational status of IES such as; excavation start/completion, truck detection, terrain model update, emergency stop, local sensing, GPS/motion sensor data handling, and so on. This paper presents the role and functions of this data communication manager. After every possible operational status of IES operation was identified, a protocol of each communication process in the form of string-type was made. The components of IES are connected with either wired or wireless network. Therefore, they can communicate with the manager using socket (TCP/IP) communication. The data communication manager is also capable of accessing a web-based project management information system, which constantly updates the performance of excavation robot to online database.

Aug 1, 2013

By Thomas Hauquin, Olivier Deck, Yann Gunzburger

"In this study, 2D numerical modeling of a room-and-pillar mine is conducted along with the calculation of all terms of the mechanical energy balance. Simulations of different geometrical and geomechanical configurations are performed in order to investigate the conditions that favor a high seismic energy release (instability) during the excavation (removal) of one single pillar. At first, classical stressstrain simulations enable us to estimate the elastic and quasi-static response of the mine. Then, owing to the implementation of new functions in the modeling code, the seismic energy released when the pillar is removed is calculated. The obtained values are found to be in agreement with those calculated analytically using a modified energy balance based on the works by Cook (1967) and Salamon (1984).It is shown that the mine’s proneness to release large amounts of seismic energy, after sudden removal of one single pillar, mainly depends on three parameters: the initial extraction ratio of the mine, the depth of the exploited seam and the Young’s modulus of the surrounding rock mass compared to that of the ore. Moreover, it is pointed out that the magnitude of the seismic energy can be greater than that of the stored elastic energy, meaning that the dynamic (seismic) transient stresses should not be neglected when compared to the quasi-static stresses, particularly when trying to prevent the risk of rockburst and collapse in underground mines."

Jan 1, 2015

By A. M. Martinez, L. Melis, R. C. Peláez, L. G. Garcia

Orovalle Minerals S. L. operates a copper/gold mine in the Asturias region of northern Spain, with the operation dating back to December 1997. The feed to the El Valle mill, consisting of oxide/sulphide (skarn) mineralization, is highly variable, even on a shift by shift basis and presents challenges to the mill operating staff on a daily basis. The mineralogical characteristics of the ore are quite complex with copper present as native copper and sulphides as well as copper minerals with deleterious elements. Gold is present as native gold and electrum. The mill circuit includes SAG/ball mill grinding, gravity recovery of native copper and gold, flotation of copper concentrate, carbon-in-leach gold recovery and SO2/air cyanide destruction. The paper will provide a description of the different unit operations and present operating data of the mill operation.

Jan 1, 2019

By J. P. Weiler

The increasing use of high-pressure die-cast magnesium alloys in the automobile industry requires a better understanding of the mechanical properties, the microstructure, and particularly, the relationship between these two. The goal of this study is to first understand the microstructural features which control the mechanical properties observed from an AM6OB magnesium alloy, and second, to be able to predict the local mechanical properties based on microstructural features encountered in different areas of the die-cast component. The two main tools used in this study are spherical indentation testing, used on local areas of the die-cast magnesium alloy AM6OB to detect changes in microstructure and mechanical properties, and X-ray tomography, used to non-destructively investigate the internal porosity in a sample. The results from these tests are then used to predict the local mechanical properties such as the yield stress, the strain-hardening characteristics, and the fracture properties of the AM6OB component.

Jan 1, 2006

By W. W. Heywood

"IntroductionCIRCULAR structures on the Arctic islands were first noticed early after World War II. During the indexing of the 1950 Royal Canadian Air Force photographs their occurrence was brought to the attention of the Geological Survey of Canada by Mr. W. B. Waugh, Surveyor General. As a result, I. C. Brown ( 195l) of the Geological Survey of Canada studied the air photographs of these structures and discussed theories that might explain their origin. The author, as a member of the Geological Survey of Canada, spent several months in 1952 and 1953 in reconnaissance study of the geology of Ellef Ringnes island, using the Isachsen meteorological station as a base. Twelve days in the summer of 1953 were spent mapping the Isachsen dome and adjacent areas. The Isachsen dome, one of several similar structures occurring on Ellef Ringnes island, is situated 35 miles southeast of the meteorological station.PhysiographyEllef Ringnes island is a mature, stream dissected plain having an average elevation of about 400 feet. The surface of the plain is undulating with a relief of about 150 feet; only a few of the numerous streams that form a dendritic drainage pattern have eroded valleys this deep. Long, low, cuesta escarpments cross' the plain, which is underlain by sedimentary rocks of Lower Cretaceous and possibly younger age. The sedimentary strata have a low regional dip to the southeast; exceptions are found in the vicinity of the domes, where the strata are up-turned, and in the plateau region, northeast of Deer bay, where they are flat lying. The plateau, which is underlain in large part by basalt, is deeply dissected and has an average elevation of 1,000 feet."

Jan 1, 1955