Search Documents

By M. F. Gallerneault, V. Fallah, A. Howells, W. M. T. Gallerneault

"The occurrence of recrystallization in cold-worked aluminum sheet during the brazing process leads to loss of strength, an inhomogeneous grain structure and reduced corrosion resistance. AlMgScZr alloys are known for their extraordinary recrystallization resistance due to the influence of Sc and Zr addition on their microstructure. Here, we investigate the effect of alloy composition (i.e. Mn, Mg, Sc, Zr content), cold-roll reduction and pre-aging treatment on the recrystallization behavior of cold-rolled sheets at brazing temperatures typically used during the manufacture of heat exchanger units. The analysis of recrystallization behavior is carried out through microstructural characterization and the results are compared with the behavior of a commercial, AA3xxx-based heat exchanger alloy.INTRODUCTION Control of recrystallization is of critical importance during brazing, which is a widely-used joining technique for aluminum alloys in aircraft structures (Heinz, 2000) and automotive heat exchangers (Miller, 2000; Marshall, 1993). Due to excessive local heat at brazing temperatures, the cold work texture of aluminum alloys in the cold-rolled sheets may undergo a local recrystallization process (Marshall, 1993). This leads to the formation of an inhomogeneous microstructure and thus anisotropic mechanical properties (Miller, 2000) and low corrosion resistance (Marshall, 1993) across the sheet. X800, a commonly-used Al-Mn alloy series for automotive heat exchangers applications, has been developed specifically for a higher strength as well as an enhanced corrosion resistance as opposed to the traditionally-used AA3003 alloy (Marshall, 1993). X800 alloys, however, exhibit a low recrystallization resistance at normal brazing temperatures, i.e. 590°C. In contrast, Al-Sc-Zr alloys have been shown to exhibit an extraordinary recrystallization resistance at such temperatures (Riddle, 2004) while also being corrosion resistant and possessing a high room-temperature strength (Fuller, 2002). This has been shown to be due to the formation of coherent, nanoscale Al3(ScZr) precipitates that effectively impede grain boundaries while also exhibiting very slow coarsening kinetics at high temperatures (Riddle, 2004; Jones, 2003; Ocenasek, 2001). In this study, we analyze the recrystallization behavior of X800 alloys under brazing conditions through introducing Sc and Zr into the system as well as varying the Mn and Mg content. The effect of processing route is also studied by introducing a pre-aging stabilization treatment as well as varying the cold-roll reduction prior to the final brazing anneal."

Jan 1, 2018

By Jennifer Abols

In July of 2013, Lundin Mining acquired the 2,000 tpd Eagle nickel and copper project from Rio Tinto. The project had been put on hold earlier in the year and construction was approximately 50% complete. Lundin immediately accelerated project activities and by September of 2014 the project was constructed, commissioned and ramping up. The newly commissioned facilities went on to reach design throughput, recovery and product quality targets by the end of the year. This was accomplished ahead of schedule and below budget despite numerous obstacles including the worst winter on record in the past 50 years for the area. What led to the success of the project, and in particular the commissioning phase of the project? This paper takes a high level look back and provides an overview of the methodology used, key issues encountered and lessons learned to answer this question.

Jan 1, 2015

By H. Sakurai, M. Kato, F. Tanaka

The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace (CL- furnace) for settling the slag/matte mixture formed in the smelting furnace. The conditions in the CL- furnace change its settling efficiency, resulting in high variability of copper losses in slag. Modifications of the operation and maintenance procedures for the CL-furnace have significantly and sustainably reduced the copper losses in Gresik smelter to below 0.7%. A series of flow patterns evaluation in the CL-furnace demonstrated how the chemical reactions and settling conditions of the CL-furnace has been improved by the new operating procedures. Settling mechanisms for the matte droplets in the CL-furnace is also discussed using image analysis of solidified slag. INTRODUCTION The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace (CL- furnace) for settling the slag/matte mixture formed in the smelting furnace. Since the top-blowing in the S- furnace agitates the molten bath strongly, matte droplets are dispersed over the slag phase when melts flow out of the S-furnace. Thus, the CL-furnace has an important role to settle and recover matte droplets efficiently. Since many papers have ascribed major part of copper losses to matte droplets suspended in slag (Tanaka 2007; Genevski et al., 2008; Starodub et al., 2016), flow patterns of slag in the CL-furnace can affect greatly on the profitability of smelters which have adopted the Mitsubishi process. PROCESS DESCRIPTION Figure 1 illustrates the Mitsubishi process schematically. The Mitsubishi process is the only system for continuous production of blister copper from copper concentrates and consists of 3 furnaces connected by enclosed launders those ensure the minimum emission of fugitives. In a smelting furnace (S-furnace) copper concentrates are fed with flux, oxygen-enriched air to form a mixture of slag and matte which cascades down to a slag-cleaning furnace (CL-furnace). The CL-furnace settle matte droplets in the mixture on the crucible from which matte is siphoned to a converting furnace (C-furnace), while discharging the cleaned slag (CL-slag). The C-furnace converts matte to blister copper by the top-blowing of oxygen- enriched air.

Jan 1, 2019

By M. Feinendegen, Ph. Siebert, C. Clauser, K. Willbrand, M. Ziegler

"Three institutes of RWTH Aachen University collaborate on laboratory tests and numerical simulations of hydraulically driven fractures in igneous rocks. The project´s target is to enhance the understanding of hydraulic induced fractures for deep geothermal energy exploration. Based on the idea of creating new discrete fractures in hot dry rock (HDR) reservoirs, the current project stage deals with this process on a laboratory scale. Especially for this purpose, a new testing facility has been developed and laboratory tests are performed to verify a hydraulic fracture propagation code based on the extended finite element method (XFEM). The testing facility enables us to initiate and propagate fractures in large samples of dense rock under triaxial confining pressures and to monitor the fracture propagation by extensive measurements. This contribution gives a short introduction to the project‘s background and mainly focusses on the test facility, the experimental procedure and exemplary results.INTRODUCTIONThe most efficient technique to increase the permeability of subsurface rock is to initiate and open fractures by applying hydraulic pressure from a packed borehole-section and to inject fluid into these fractures to propagate them. Since its first use in petro industries to enhance the production of wells in natural gas and oil reservoirs, the interest in targeted creation of hydraulic fractures has increased exponentially. As the key technology to the extraction of unconventional gas from shale, hydraulic fracturing (HF) became a major topic in a heated public debate. Based on the fact that a fracture tends to propagate in a direction perpendicular to the minimal principal stress, hydraulic fracturing has become an established tool for estimating geological stress states in almost any depth. Enhanced geothermal systems (EGS) in HDR reservoirs use engineered fractures as a heat exchanging system for a cycling fluid driving a power plant."

Jan 1, 2015

By E. L. Martheleur

A general expression for the electric power generated or consumed in a direct-current circuit is obtained by multiplying the reading of a suitable voltmeter connected across the terminals by the reading of an ammeter connected in the circuit. by the reading of an ammeter connected in the circuit. When alternating currents are considered, the product of the volts and amperes as obtained for direct currents does not generally represent the true energy involved; it is greater than this true energy and should be multiplied by a certain factor which may have any value between zero and unity, according to the conditions of the circuit. This factor is called the power-factor of the system, and expresses the ratio of the true energy over the apparent energy. For a three-phase system the expression of the apparent energy is [\/ 3 x E x I; ] while the expression of the true energy, that is, energy suitable for mechanical work, is [v? 3 x E x I x cos A.] The total current of a circuit corresponds to the reading of an ammeter connected in the circuit; it is the resultant of two currents. The first of these is in phase with the voltage, and is that portion which really produces mechanical work; the second is always in quadrature with the voltage, that is it may lead or lag the voltage by 90° according to the condition of the circuit. This second current does not produce any sensible work, and for this reason is sometimes called wattless current or reactive current.

Jan 1, 1924

By L. D. Smith

"The economic evaluation of a mineral project requires a great deal of diverse information to be brought together in one place. The greatest concern is that there will be an error by omission, so it is useful to have a detailed list of what one needs to know in order to make a thorough evaluation. The list that is presented below is intended to act as a checklist for the person who develops and reviews an evaluation, and as a shopping list for the persons gathering data at the project site.There are varying degrees of detail required at the different stages of evaluation in a project, from the ""quick and dirty"" overview, to the pre-feasibility study, to a full detailed feasibility study, to a due diligence review. This list addresses most of the economic variables in a project and can be used for all levels of studies. Its purpose is to identify a variable or issue and to raise a question, which the reviewer can then pursue in more detail using increasingly more comprehensive checklists for each topic. While developed from the point of view of a new project, this list is equally valid for an ongoing operation."

Jan 1, 1994

By S. Kaushik

The control room in a mineral processing plant has become increasingly complicated with complex unit operations coupled with rapidly evolving systems of sensors and control. Even with significant automation, human intervention is required to counter various scenarios that play out every day. A typical control room operator must monitor over 300 individual points of data in order to ensure the safe and efficient operation of the plant. At the same time, the experience of the workforce is decreasing as operators retire and the new generation enters the concentrators. Global competition for skilled operators continues to be strong and the opportunity to apprentice has diminished. The challenge is to provide a skill foundation for the operators so that they can be effective in the concentrator in a timely and safe manner. Progressively, the industry is turning to dynamic simulation tied into the control system. The simulator environment operates behind the control system to emulate the plant operation, reacting as the plant would when a change is made. The operator drives the process, with realistic feedback, which enables learning in a safe environment. This paper will take the reader through a green-field case study and discuss the effectiveness of integrating an operator training simulator (OTS) on the operator’s learning curve.

Jan 1, 2014

By J. R. Perumareddi, V. S. Sastri, M. Elboujdaini

It is well known that high strength steels used in aerospace industry, are generally susceptible to hydrogen embrittlement during surface treatment such as electroplating with zinc on cadmium. Hydrogen embrittlement reduces ductility and results in brittle fracture rather than failure by plastic deformation. Hydrogen embrittlement of high strength steels is mitigated by surface treatment such as plating with other metals. Data on the hydrogen contents of steels before and after surface treatment by hot extraction-thermal conductivity, secondary ion mass spectrometry (SIMS) and UV-visible spectroscopy along with the mechanism are presented.

Jan 1, 2006

By H. Saeedi Ali, A. J. Monhemius

"Anglo Asian Mining’s Gedabek mine is situated in the Lesser Caucasus mountains in Western Azerbaijan. The ore body is a complex copper-gold porphyry deposit, comprising intermixed oxidized, transition and sulphidic gold and copper-bearing ores. Gold in the sulphide ores is generally not refractory and is recoverable by cyanide leaching, but the secondary copper minerals, which are also cyanide soluble, lead to high cyanide consumptions. Ore processing at Gedabek is by agitation leaching for high grade ore (>1g Au/t) and heap leaching for lower grade ore. In order to cope with the high copper concentrations in the cyanide leach liquors, a unique combination of resin-in-pulp for selective gold extraction and SART processing for copper removal and cyanide recovery is used. In 2015, a flotation plant was added to treat the tailings from the agitation leach plant before the tails are sent to the tailings dam. This plant produces a copper sulphide flotation concentrate and also recovers some of the residual gold and silver in the tailings. Since February 2017, due to lower grades of gold and higher copper in the feed ore, the decision was taken to alter the flow sheet and to carry out flotation ahead of agitation leaching, to reduce the cyanide consumption during leaching by removing soluble copper minerals. The paper compares and contrasts the performance of the plant in the two configurations, namely, (i) leaching followed by flotation and (ii) flotation followed by leaching.INTRODUCTION In May 2009, Anglo Asian Mining started open pit mining for gold on its Gedabek property in the Lesser Caucasus Mountains in western Azerbaijan. Gedabek is situated on the highly mineralized Tethyan Belt that runs from the Himalayas to the Balkans. The ore body at Gedabek is a complex copper-gold porphyry deposit, comprising intermixed oxidized, transition and sulphidic gold-bearing ores. The sulphidic ores contain mainly pyrite and chalcopyrite, with some secondary copper sulphide minerals, such as bornite and chalcocite, and minor amounts of sphalerite, galena and tetrahedrite. Gold in the sulphide ores is generally not refractory and is recoverable by cyanide leaching, but the secondary copper minerals, which are also cyanide soluble, lead to high cyanide consumptions and passivation of free gold."

Jan 1, 2017

By L. I. Kiss, S. Perron, D. Toulouse, S. Poncsák, A. Perron

Bubbles play an important role in many industrial processes. In a Hall-Heroult cell, used for aluminum production, bubbles contribute to induce flow in the cell. The induced flow is important for the thermal balance of the cell as well as for the distribution and dissolution of the alumina. The existence of the bubble layer does not have advantages only. It increases the voltage of the cell and causes deformation along the cryolite-molten aluminum interface. The role of the anode inclination in the behaviour of the bubble layer as well as in the hydrodynamics of the bath is not clearly understood. In this work, the effect of the anode inclination angle on the bubble driven flow is studied in an industrial scale air-water model. The inclination angle is varied up to 5° from the horizontal. The instantaneous flow field is captured by Particle Image Velocimetry (PIV) system. The mean velocity fields were calculated by ensembleaveraging the instantaneous velocity fields measured at different time. The existence of the counter-flow in the interpolar space and the vortex in the side channel has been confirmed. Furthermore it has been observed that the effect of anode slope on the velocity field is weak.

Jan 1, 2006

By Radford B. Langston

Mining Methods Majority of Production Ramp and Fill at Stillwater, Sub-level Becoming More Important Production at East Boulder from Sub-level l Majority JM REEF ROCK TYPES NORITE - plagioclase and bronzite cumulate GABBRONORITE - plagioclase, augite, and bronzite cumulate TROCTOLITE - plagioclase and olivine cumulate ANORTHOSITE - plagioclase cumulate PERIDOTITE - olivine cumulate

May 1, 2002

By Yosuke Ota, Makoto Tawara, Tetsuya Kojima

"Dry-lube has been used in Europe to enhance formability of aluminum sheet for automotive applications, but it is difficult to ensure degreasing performance with lower degreasing bath temperature. However, newly developed, highly lubricating pre-coats utilizing a urethane resin, which is soluble in water, have been found to show excellent degreasing performance. Furthermore, a richer pre-coat weight coincides with a lower friction coefficient and better formability. Combined use of anti-rust liquid oil showed different friction coefficient depending on applied surface pressure.INTRODUCTION The global demand for aluminum alloy products, especially for automotive application, has been increasing because aluminum alloys can offer excellent corrosion resistance with good strength and low density compared with steel. Aluminum alloys can contribute to saving much more energy and greenhouse gas emissions over the lifetime of the product. On the other hand, the amount of aluminum alloys in vehicle architectures is still somewhat limited due to relatively low formability. As a consequence of this low formability, it is necessary to set a certain limit to the shape of an aluminum alloy panel for automotive applications. So far hot melt wax dry lubricants have been in use especially in Europe as they have been recognized to provide better lubrication than conventional rust protection oils (Meiler & Jaschke, 2005). The benefit of hot-melt wax for automotive manufacturing is associated with a more stable forming process and the possibility to avoid extra lubrication in the press shop. But because of the low poorer solubility of hot-melt wax in degreasing aqueous bath solution, a higher degreasing temperature is required so that no remnant of hot melt wax can be carried over to the next manufacturing process. This temperature control is difficult to impress upon a manufacturing degreasing bath originally designed for liquid oil, especially in Japan. The typical temperature of degreasing bath in Europe is around 60°C, while it is only around 40°C. in Japan. Various types of pre-coats other than hot-melt with high lubricity have been reported (Tawara, 1993; Ueda, Hatsuno & Totani, 2013), but a balance between sufficient degreasing performance and high lubricity has not yet been achieved for an actual production process line."

Jan 1, 2018

To determine the optimal circuit configuration for gravity gold recovery consideration should be given to a range of factors in addition to the efficiency of the gravity circuit, including capital costs, ease of operation and impact on comminution. The most common gravity gold circuits utilise a centrifugal concentrator treating a portion of the hydrocyclone underflow. This paper will examine this option and alternative circuit configurations to illustrate the effect of various gravity circuit feed and tailings configurations on the equipment sizing, capital costs, operating costs, water balance, comminution efficiency and gravity gold recovery. The optimum circuit configuration can provide reduced capital and operating costs, maximise gravity gold recovery and improve comminution efficiency.

Jan 1, 2011

By S. D. A. Hannot, H. Knapp

"High pressure grinding rolls (HPGR’s) are an energy efficient solution for comminution of industrial minerals and metal ores. The technology is successfully applied in an expanding field of applications throughout the minerals industry. HPGR’s compress and grind the particle bed in the operating gap between two counter-rotating rolls. The equipment provides a high capacity, low energy alternative for applications with conventional tertiary and quaternary crushing and grinding, with size reduction reaching from 100mm down to 25 microns product. In this process, maintaining a controlled and evenly distributed operating pressure between the rolls is very important. Due to feed segregation, the pressure distribution along the roll’s length can become uneven, resulting in a coarser product. This paper will show that the best approach to compensate and adapt for the uneven pressure is to allow the rolls to skew relative to each other. Coarser products are also caused by an inadequate pressure distribution: the much-discussed edge effect. To minimise the consequence of the edge effect, an optimised ratio for the roll length to diameter will be calculated. Furthermore, the design philosophy behind a cheek plate will be detailed. This cheek plate is used to retain the material between the rolls, reducing the edge effect while still allowing roll skew. Together these design considerations help optimise HPGR’s performance.INTRODUCTION Initially developed for the cement industry during the energy crisis in the 1980’s , high pressure grinding has been an accepted technology for many years. It has been successfully implemented throughout the minerals industry, with applications in base and precious metals, as well as industrial minerals processing. The comminution process relies mainly on size reduction through to compression and inter-particle crushing in a particle bed in the operating gap between two counter-rotating rolls. The equipment typically has a high unit capacity and low energy consumption, and is increasingly used as an alternative to conventional tertiary and quaternary crushing and grinding, in particle size ranges reaching from 100mm down to 25 microns. It can be applied to moist ores and dry material, in open circuit arrangement or in a closed circuit with dry or wet classification (screening, air classification)."

Jan 1, 2019

By R. E. Phelan

Introduction The Flin Flon deposit was discovered by Tom Creighton, an experienced prospector and trapper, who in 1914 made his headquarters at The Pas, Manitoba, and still lives there. The discovery was made in the fall of 1914, and Creighton and his associates spent the next summer in investigating the find. In August of 1915 the first claims were located. The property was optioned to Hayden Stone & Company, and in the spring of 1916 they started a diamond-drill campaign. Hayden Stone spent $50,000 on the property and, among other things, completed over 7,500 feet of diamond drilling. The ore not being as high grade as expected, and also being complex in character, Hayden Stone then abandoned their option. In the spring of 1917, Messrs. Earle, Faskin and associates took an option on the property and started an extensive drilling campaign. This campaign accomplished approximately 18,000 feet of drilling and secured for the Faskin interests a 32 per cent interest in the property. In 1920, W. B. Thompson and The Mining Corporation of Canada secured an option, and, while this option was in force, sunk two shafts in the ore-zone and did a considerable amount of drifting and cross-cutting in the ore to study the manner in which it occurred in place, and, by actual channel sampling, to check the grade indicated by the previously accomplished diamond drilling. All of this work had indicated that an ore-body existed on the property containing at least 18,000,000 tons of ore, assaying as follows: gold, 0.074 oz./ton; silver, 1.06 oz./ton; copper, 1.71 per cent; and zinc, ). 45 per cent (1). Complete analyses of composites from the drill holes showed that the ore was very complex in character. It contained the above values in gold, silver, copper, and zinc, as well as large amounts of sulphur and iron, and traces of lead, arsenic, antimony, cobalt, and various other metals. Although the ore was obviously pyritic in character, pyritic smelting, the usual method of treating this class of ore, could not be used to beneficiate the ore with any reasonable expectation of making such a venture a financial success, since coke and coal landed at Flin Flon would be expensive, and siliceous flux was known to be scarce locally and low in grade. The property therefore lay idle until 1925.

Jan 1, 1935

By T. M. Ahmed

Sherritt International Corporation experienced corrosion failures with the 316L stainless steel tubing in a high-pressure still condenser employed for ammonia recovery. A detailed failure analysis was conducted on the condenser tubing to determine the mode and the root cause of the failure. The analysis included both optical and scanning electron microscopy (SEM) of the inner and outer surfaces of the tube as well as characterization of the corrosion products using energy-dispersive X-ray spectroscopy (EDX). Results revealed that the corrosion attack was confined to the first ?100 mm of the tubing at the inlet where the tube was connected to the top tubesheet. The tube suffered both external stress-corrosion cracking (SCC) and crevice corrosion from the shell side (water side), and wall thinning of the inner surface (the tube side) due to erosion corrosion. It was evident that failure of one of the tubes occurred due to SCC that penetrated the whole wall thickness and resulted in a leak failure. Some prevention measures are proposed to avoid this type of corrosion attack in the future.

Jan 1, 2005

By J. J. McDougall

Until quite recently, the coal in the Cape Breton field was won from comparatively thick seams with light cover, and from submarine areas, and the system of mining naturally followed was pillar-and-stall. This sytem permitted of cheap extraction, and enabled production from localities where other methods could not be employed to good advantage. Thus the pillar-and-stall system, applied to conditions as stated, justified its adoption. Our working seams today, however, are practically all under heavy cover, or are moving in that direction, and with this gradual increase in cover came the increased cost of roadway maintenance. At Princess colliery, the system of pillar-and-stall was followed until roof and bottom conditions became such that further operations were unprofitable, and the longwall method was then adopted as an economic necessity. This fact should be borne in mind when operating costs of both systems are being compared. The longwall method is not held as a cure for all difficulties of heavy cover, but through it these difficulties can be overcome with less expense than by pillar-and-stall. The longwall system of mining, strictly speaking, is one by which a seam of coal is totally extracted in one operation. There are, however, many modifications of longwall, and in some cases it is difficult to determine whether certain practices should be classed as longwall or pillar-and-stall, or a combination of both.

Jan 1, 1928

By Yi Yang, Mark Zoback

"We report laboratory studies of the time-dependent deformation of core samples from four different formations in the Williston Basin - the Lodgepole formation, the Middle and Lower Bakken formations and Three Forks formation. The laboratory tests reveal varying amounts of viscoplastic deformation in response to applied differential stress. The time-dependent deformation is generally greater in rocks with higher clay and organic content, and can be described by a power-law function. Because the magnitude of the creep strain is linearly proportional to the applied differential stress, we can utilize viscoelastic theory and geophysical logs to estimate the degree to which tectonic stress is affected by viscoplastic stress relaxation. We suggest that viscoplastic stress relaxation results in the Upper and Lower Bakken Formations act as frac barriers during hydraulic fracture stimulation in the Middle Bakken, but the Lodgepole and the Three Forks Formations are not frac barriers.INTRODUCTIONHorizontal drilling and multi-stage hydraulic fracturing in shale reservoirs are critical for successful exploitation of ultra-low permeability shale gas, tight gas and shale oil reservoirs. Characterization of the mechanical properties of the reservoir rocks is essential to understanding the behavior of rocks during drilling and completion. Previous laboratory studies have shown that the timedependent deformation in clay-rich shales can be characterized as linear/viscoelastic deformation (Chang et al., 1997; Hagin and Zoback, 2004a, b; Sone and Zoback, 2013b, 2013c). Sone and Zoback (2013c) showed that laboratory measurements of time-dependent deformation in various gas shale reservoir rocks, and demonstrated that the viscoplastic deformation of these rocks can be characterized by a power-law function. They interpreted the results in the framework of linear viscoelastic theory to quantitatively assess the geomechanical effect of viscous time-dependent deformation over engineering and geological time scales. (Sone and Zoback, 2014) further extended the theory and proposed a viscous relaxation model that can be applied to predict the continuous differential stress magnitude using the geophysical logs. They tested the validity of their model by comparing the stress prediction with the occurrence of drilling induced tensile fractures (DITFs) and the vertical hydraulic fracture penetration observed from microseismicity."

Jan 1, 2015

By R. Pot

"IntroductionTHE PURPOSE of this paper is to discuss briefly the main logging and testing devices presently at our disposal, to point out some of their limitations, and to suggest possible improvements of the techniques.Some of the more important devices .are those that are used in:(1) Coring(2) Formation testing(3) Electric well logging(4) Radioactive well logging(5) Measuring of bottom hole pressures(6) Sampling of reservoir fluidsThe first four of these procedures are concerned with the well while it is in the process of drilling. The last two are carried out as soon as possible after a well has been brought into production and .at intervals during its life. My remarks will be concerned mostly with certain aspects of formation testing. The reservoir engineer is dependent on the information derived from these operations in order to obtain a clear picture of the conditions in a reservoir and to enable him to assess and forecast its future behaviour.Since any calculation is no better than the data on which it is based, not enough emphasis can be placed on the necessity for the testing and logging equipment to be of the highest quality and for the analysis of the results obtained to be thorough."

Jan 1, 1952

By Gilles Carrière

"The Huntingdon mine of Quebec Copper Corporation is situated 3 miles south of the village of Eastman, in the Eastern Townships of Quebec. The copper deposit consists of several pyrrhotite-chalcopyrite replacement bodies or bands.The first mining operations on the conspicuous surface gossan of the Huntingdon deposit started in 1865. They were suspended in 1883. The .mine was again active from 1890 to 1893 and from 1912 to 1924. These operations were carried to a depth of 500 feet, and it is estimated that some 150,000 tons of ore were extracted, of a grade reported as varying between 3 Yi and 7 per cent copper.In 1950 a program of exploration was initiated in the area of the old mine, and resulted in the finding of 500,000 tons of ore with a grade of 2 per cent copper. A new shaft was sunk to a depth of 1,160 feet, and by February 1954 the mine was extracting 800 tons of ore daily.General Geology and StructureThe mineralized zones are on the west side of a band of altered volcanic rock, locally called andesite, adjacent to a sill-like body of serpentinized peridotite which lies west of the andesite. The bands of andesite and serpentine extend several miles north and south of the mine. Their strike is generally north 15 degrees east, and they dip steeply east. Their widths vary very considerably along the strike, but in the mine area each is about 450 feet wide on surface. They are enclosed in sediments of the Caldwell series, consisting of greywackes, quartzites, slates, and shales. The andesite belongs to the same series, which is thought to be of Cambrian age (1). The ultrabasic intrusive is post-Ordovician.At p\aces along the serpentine contact the andesite shows a pronounced schistosity; it is parallel to the contact and rarely extends farther than a hundred feet from it. No evidence of strong folding or faulting has been found so far in the mine workings. Some apparent distortions and irregularities in the strike of the contact may all be due to the intrusive nature of the serpentine. In the mine area, transgressive tongues of serpentine point southward in the andesite.A few vertical lamprophyre dykes, not more than five feet thick, cut the other formations at right angles."

Jan 1, 1949