Search Documents

By J. Bednar, R. R. Rogers, W. Dingley

"Zinc is by far the most important metal used for protecting steel from the ravages of corrosion, and cadmium is also used extensively for this purpose. These metals are applied by electrodeposition in cyanide baths when a particularly good appearance and high throwing power are required. One great disadvantage in using these baths has been the decrease in cyanide concentration and the increase in carbonate concentration that takes place during the plating. Another disadvantage has been the development of serious embrittlement in high-strength steels. The present authors have developed new cyanide baths for electroplating both zinc and cadmium on steel. These baths are stable in composition during plating, they have not produced appreciable embrittlement in the high-strength steels that have been investigated up to the present time, and they permit the use of considerably higher plating current densities. In addition, they produce extremely fine grained coatings that are attractive and have excellent adherence and covering properties. Brighteners can be used in the plating baths if bright finishes are required."

Jan 1, 1967

By Muhammad Zaka Emad

Cemented rockfill (CRF) is a mixture of rock aggregate and binder slurry. It is a stiff backfill, it is fast curing, its operation is simple, placement rate is reasonably high and no drainage is required. The main demerit of CRF is failure of exposed faces causing ore dilution, which can be associated with the fill placement method. This paper discusses the effects of two placement methods being practiced by mines and numerical modelling is used as a tool to evaluate stability of the backfill column. In the first method, practiced in longitudinal retreat mining of a narrow vein deposit, the rockfill is hauled and dumped into the stope with a LHD scooptram. Once dumped, cement slurry is sprayed into the stope. In the second method, a raise situated centrally above the mined stope is used to convey already mixed CRF into the stope. Stopes are mined out transversely in primary and secondary blocks in a sublevel stoping system. Problems of poor mixing in combination with both placement methods are discussed. The two backfill placement methods are analyzed for blast induced vibration damage using the dynamic Flac3D modelling technique accounting for rock mass and fill damping characteristics, and a pressure wave is used to simulate the blast vibrations. Fill heterogeneity has also been considered for the two cases and results are compared.

Jun 1, 2012

By M. Kamyab

Transportation of fluid and slurry (fluid and solid particle mixtures) in a pipe and annulus space has been the focus of numerous studies. There are different parameters to be considered when studying slurry transportation. These include slurry velocity or flow rates; fluid properties such as density and rheology; and solid particle properties including concentration, density, shape and size. Also the angle of the flow conduit, rotation of the pipe and possible eccentricity of the annulus are other factors which influence slurry transport characteristics. Although a number of analytical, numerical and empirical equations as well as numerical simulations have been developed for studying the flow and slurry transport characteristics, the results need to be validated against either field or lab data. As performing field tests is costly and time consuming, conducting simulations at the laboratory scale appears as a good alternative. Different flow loops have been designed to study slurry transport behaviour in different science and engineering disciplines including oil and gas and mining. However, few of these consider, in particular, cuttings transportation in small size annulus space. The flow characteristics appear to be very different when slurry travels within a small size annulus, in particular when the fluid velocity is high. In this study, a review of some of the existing slurry flow loops will be conducted. Then the details of a slurry loop, which has been designed and commissioned for the purpose of studying cuttings transport in a small size annulus space for applications in drilling mineral exploration wells using coil tube technology, will be presented.

Aug 1, 2013

By E. A. Rychkun

"For the last 700years of recorded economic history, man has been subjected to alternating inflationary and deflationary patterns. Through this period of time, a severe deflationary pattern has developed approximately every 55 years, creating 12recordable occurrences. Through the last two centuries, this severe deflationary phenomenon has come to be known as a depression. As these depressions have repeated themselves regularly, they are cyclic. This in turn leads to the question of whether the 13th cycle will also repeat itself in the form of a depression. As this cycle is now 51 years old, we must consider the possibility at about 1984.In analyzing a 700-year record of consumer prices in Southern England, the 55-year cycle appears to vary in shape and intensity. This varying phenomenon is due to the effect of longer cycles upon which each one ""rides "". Because each cycle effectively rides on the next largest, which in turn rides on the next largest and so on, the combined measured effect of all cycles together at any point in time is always unique. This means that anyone cycle can never repeat itself in an exact identical manner. The combined effect therefore is what we observe in the form of prices and, as cycles interact, variations in deflation are produced . The ""science"" of economics attempts to quantify and develop theory on situations which are never identical and hence can be conservatively classified as a useless predictive tool.This means that more unconventional approaches may be required to predict our economic future. In looking at previous depression cycles, it is possible to recognize similarities in human behaviour patterns and hence the resulting economic movements. These behaviour patterns create major events or influencing factors which set the scene for a major deflationary condition. The way in which these factors occur, however, is not predictable. As more and more of these similar events are identified in each cycle, we can increase our confidence on the probability of the last event occurring (a depression). By also unravelling the set of larger cycles, we can determine the potential combined effect at any point in the future.This paper presents a system of cycles ranging from 800 years to 3 years which appear to operate in our economic system. By so doing, a long-term projection into the next century can be made. Finally, the paper deals with the main controlling similarities within the depression cycle, to show that a comparison with our current cycle implies that a major deflationary collapse in the mid 1980's is virtualy inevitable."

Jan 1, 1980

By W. Griffith

"While oxalic acid precipitation practices are commonly applied on purified rare earth elements (REEs) pregnant leaching solutions (PLS), few efforts have been reported using oxalic acid (OXA) to recover REEs directly from untreated PLS. High oxalic acid demand is the most significant issue in all these direct oxalic precipitation (DOP) practices. Preliminary research on DOP of REE from a dilute PLS originating from an acid bake followed by water leaching was conducted. At 75°C, the oxalic acid demand was between 12 and 18 times the stoichiometric requirement for complete REE precipitation. Conducting DOP at 25°C had superior REE recovery but the product purity and filterability declined. Between 75°C and 100°C, REE recovery increased with increasing temperature. When sodium hydroxide was used to adjust the pH during DOP, in the range of 0.5 to 1.5, higher pH benefited REE recovery. Using ammonium hydroxide in place of sodium hydroxide, the REE recovery was reduced by close to 5%. Sodium chloride addition to the PLS was also investigated and the results showed that at both 75°C and 25°C, the REE recovery was enhanced substantially. At 25°C, when the oxalic acid addition was controlled at 4.7 times the stoichiometric requirement, the overall REE recovery reached 95% with the addition of 240 g/L NaCl. Other reagents such as KCl, NH4Cl also showed significant enhanced REE recovery at the same oxalic acid addition. The addition of sodium sulphate appeared to largely enhance the precipitation of LREE but inhibited the formation of HREE oxalate. All results indicate the formation of rare earth double salts may play an important role in REE DOP sulphate media.INTRODUCTIONThe conventional routes for recovering rare earth elements (REEs) from a sulphuric acid pregnant leaching solution (PLS) involves an initial purification step for removal of iron, aluminium for example by precipitation through neutralization, followed by precipitation of REEs as hydroxide, oxalate or carbonate salts, or by bulk solvent extraction for REE recovery (Xia, 2013). Another route was used by Bayan Obo in their historical flowsheet, where the PLS was first subjected to double sulphate precipitation, then the remaining REEs, mostly heavy rare earth elements (HREE), were recovered by oxalate precipitation (Li, 2011)."

Jan 1, 2016

By Ann Lamontagne

Le parc à résidus de l?ancienne mine Dunraine contient des résidus générateurs de drainage minier acide. Le concept proposé pour la restauration du site est d?utiliser le fort potentiel alcalin des boues rouges, résidus d?aluminerie, afin de neutraliser les résidus miniers. En appliquant une certaine quantité de boues rouges à la surface du parc, on provoquera une neutralisation de l?acidité. De plus, les alcalis contenus dans les boues rouges vont provoquer la précipitation de minéraux stables (sulfates tel la jarosite). La précipitation de ces minéraux provoquera la formation d?une couche indurée qui rendra difficile la circulation de l?oxygène et de l?eau. Bien que ce concept ait été vérifié en laboratoire, ce sont là des hypothèses qui restent à vérifier dans des conditions réelles d?exposition. Les principales questions soulevées par l?utilisation des boues rouges, mis à part le contexte géochimique, est le contexte technico-économique. En effet, le transport de quantité importante d?un matériel argileux humide présente un défi économique important. Outre le défi économique, la manipulation et l?épandage de ce produit sur des parcs à résidus constituent également un défi important. Cet article présente les conclusions d?une étude technique sur le transport, la manutention et l?épandage de boues rouges sur un parc à résidus situés en Abitibi : le site de Dunraine.

Nov 1, 2002

By P. Archer

The Blondeau Formation has been examined in a stratigraphic drill section at Barlow Lake. The formation contains pyroclastic flows and volcanogenic sediments throughout, but epiclastic sedimentary rocks dominate the upper parts of the section. Five distinct types of pyroclas tic flows are known in the section, as well as minor mafic lava flows. Volcanogenic sediments are commonly intercalated with the true volcanic rocks. Sedimentary rocks include fine-grained intraclastic sandstones, heterolithic sandstones and green and black shales. Interpretation of the origin and relative disposition of the volcanic and sedimentary rocks favours a model of near-emergent vulcanism in an upward shoaling environment.

Jan 1, 1984

By S. Kashani-Nejad

The formation of oxides during the dehydration of MgC12,6H20, Bischofite, was studied by heating the bischofite over a range of time and temperatures in ambient atmosphere. Using a methanol-leaching technique developed by authors, the oxides that formed were isolated, identified and assayed. Three distinct regions of oxide stability were identified. The oxide produced at dehydration temperatures less than 300 °C was Mg2(OH)3C1,2H2O; at 300 °C, mixtures of MgOHC1 and Mg2(OH)3C1.2H2O were formed and at 400 °C, MgOHC1 was the only oxide produced. The presence of MgO observed in the products of the dehydration of bischofite at temperatures above 400 °C was due to the thermal decomposition of the MgOHC1 that was formed while the sample was heating to over 400 °C.

Jan 1, 2006

By F. Calizaya, S. Bhattacharyya

"This study presents the results of a set of sound level measurements carried out in three underground mines where auxiliary fans are used regularly. Sound levels as high as 100 dB(A) by the workings and 115 dB(A) by the fans were measured in these mines. These levels are quite high even for intermittent noise. Ventilation layouts and best practices used to overcome potential problems related to overexposure to fan noise in underground hard-rock mines are presented here. Factors such as fan type, rotational speed, and silencer-duct arrangements and their effects on noise attenuation are discussed. INTRODUCTION Auxiliary fans are used in hard-rock mines extensively. They are used to ventilate development headings, crusher rooms, conveyor transfer points, and underground shops. They are also used in developing long tunnels and ramps. Depending on the flow requirements and space restrictions, single or double stage axial fans with rigid or flexible ducts are used. Usually, they are high pressure (3.75 kPa) fans with flow rates ranging from 7.1 m3/s to 30 m3/s. The input power varies from 15 kW to 113 kW (Mutama, 2004; O’Connor, 2008). Typically, a 113 kW fan can produce sound levels as high a 113 dB(A) (Howes, 2005). Silencers are often omitted for cost reduction purposes or when used, they are not well maintained. Furthermore, silencers provide limited attenuation depending on their length and type. Typically, the sound attenuation ranges from 10 dB(A) for a 1 × D silencer to 14 dB(A) for a 2 × D silencer, where D is the fan diameter. In a mine, the silencer is subject to wear and tear, especially when the silencer is used in harsh environments. The interior lining can get clogged and the acoustic fill can get covered by dust and diesel soot, thus reducing the silencer performance. Periodic cleaning of the interior casing can increase the attenuation capacity of a silencer by 6 to 9 dB(A) (Dabson & Acuña, 2017). However, this requires a special silencer design in which the inner cartridge can be removed, the sound absorbing material replaced, the inner casing cleaned and the whole set retrofitted. A number of techniques can be used to reduce auxiliary fan noise in underground mines. These range from selecting the right fan for the job to installing adequate silencers. The choice depends on the air quantity requirement at the working place, cross-sectional area of the opening, duct diameter, fan type (axial or centrifugal) and local restrictions. Auxiliary ventilation layouts and best practices used to overcome potential problems related to overexposure to fan noise in underground hard rock mines are presented here. Factors such as fan type, rotational speed, duct diameter, and silencer-duct arrangements and their effects on noise attenuation are discussed."

Jan 1, 2019

By V. G. Papangelakis, G. A. Moldoveanu

"Rare earths adsorbed on clay minerals are easily recovered via ion exchange during leaching with inorganic monovalent salt solutions. The leaching efficiency of various salts at 0.5M and 25°C was investigated as a function of cation type and salt system (sulphates vs. chlorides). (NH4)2SO4 was identified as the lixiviant of choice and a procedure was established to investigate the influence of lixiviant concentration, temperature, pH and agitation on desorption kinetics and REE extraction levels. It was determined that the kinetics were fast and the optimum leaching conditions (for >80% total REE extraction) required pH below 5 and moderate temperatures (<50°C). INTRODUCTIONRare earth elements (REE) are at the core of numerous advanced applications due to their various uses in high strength permanent magnets, lasers, automotive catalytic converters, fiber optics/superconductors, and electronic devices (as phosphors in TVs and display screens for computers and cell phones). Because of the ongoing development of new technologies, there is an increased demand for REE in the international market, with emphasis on identifying new resources to insure an adequate supply for present and future use. World production of rare earths is dominated by China, the United States and Australia; however, in terms of resources, China dominates the world potential with reserves estimated to be over 90% of the total (Chen, 2011).The main commercially significant REE sources, as reviewed by O’Driscoll (1991) are bastnasite (carbonate) and monazite (phosphate) minerals, containing up to 70% wt. rare earth oxides (REO). In spite of being high grade, these ores are associated with elevated recovery costs due to difficulty in mining, separation and beneficiation. Moreover, aggressive conditions are required to solubilize the REE from the mineral, such as leaching with hot, concentrated acids or baking in 70% NaOH (Gupta & Krishnamurti, 2005)."

Jan 1, 2012

By C. H. Stockwell

THE Eastern Townships of Quebec have been the chief Canadian source of chromite. Production, however, has never been large and, except for a period of steady but small output between 1894 and 1909, mining has been active only in war time. The known deposits are too small or too low grade to compete with overseas sources in normal times. During the last war, shipping difficulties and a greatly increased demand in the United States resulted in high prices and a ready market for low-.grade material. The Quebec chromite industry flourished and played an important part in relieving the wartime shortage. Shipments in 1918 .amounted to 15,600 tons of crude ore and 6,400 tons of concentrates. At the outbreak of the present war it was natural to turn again to the Quebec field as a possible source of this strategic mineral. Some of the old properties have since been opened by private and government money and some new deposits have been found. Total mill capacity is 750 tons per day, as compared with 200 to 300 tons in 1918. During 1940, 1941, and 1942, about 85 chromite deposits were examined by the Geological Survey in a belt 100 miles long and up to 7 miles wide. A part of this belt, about 35 miles long, in which the geological features ?were not well known, was mapped on a scale of 1/2; mile to an inch.? Small ..areas around some of the deposits were mapped in detail, on scales of 20 to 200 feet to an inch. Some geophysical work was done but did not result in the discovery of ore. Prospecting by stripping and trenching was then undertaken and chromite ore was uncovered at several localities. The above work was done by the writer and by J. W. Ambrose, who has kindly contributed his results for incorporation in this paper. Y. O. Fortier actd as assistant in the geological work and, in 1942, was in charge of a sub-party engaged in geological mapping. The author is indebted to H. C. Cooke and J. W. Ambrose for reading the original manuscript and for offering many helpful suggestions for its improvement.

Jan 1, 1944

By L. L. Sirois

Because segments of the Canadian mineral-based economy are dependent totally or in part on foreign sources of certain minerals, their well-being may well be affected by inability to obtain these minerals. Where such dependency exists, it is therefore important that contingency plans be available to counteract possible price increases or lack of supplies by means of technology, developed well in advance of any pending crisis . Canada is vulnerable to possible future real or artificial shortages of certain foreign-produced mineral commodities, and science and technology can provide information for the development of policies for counteracting efforts by foreign exporters to control prices or limit supplies.

Jan 1, 1977

By P. D. P. Hamilton

IT is perhaps obvious to most individuals who are interested in the mining industry that a producing mine has been subjected to several phases of engineering attention. In this paper it is the author&apos;s hope that a thoughtful survey of these various engineering phases will emphasize certain points of value and interest which may sometimes be overlooked. The points which we will bring out are being made in an analytical sense and are not in any way a reflection on any individuals or organizations which might see in these illustrations a similarity co chair particular conditions. In other words, we are drawing on our general experience to illustrate the points which we chink are worthy of mention, and which we believe are of a type sufficiently frequent co be emphasized. It is well co point out chat, in this paper, we are not concerned with the relative importance of such theoretical questions as to whether or not a geologisc is more important than a prospector, or the office manager than the surface foreman. We are, however, interested in analyzing the various types of engineering experience required in the bringing of a mining enter-prise from the early prospect stage in co-production, and their importance to the project as a whole. In order to simplify our analysis of the subject, it has seemed best to outline a simple mining organization. In using the terms &apos;industry&apos; and &apos;business&apos;, we feel chat frequently those engaged in mining do not always appreciate that mining is actually an endeavour, or a business, which has the same economic fundamentals as any other business. In the mining industry, the field and producing engineering are counter-parts of the research and production phases of any other type of business. Once this is realized, it is fairly obvious that mining, like any other industry, is a matter of economically acquiring raw materials, processing them, and finally marketing the resultant commodities as favourably as possible. The points may be discussed in a little more detail as follows.

Jan 1, 1938

By Alfred C. Lane

WE recently received from Professor A. C. Lane, Emeritus Professor of Geology and Mineralogy, Tufts College, Mass., and a Corresponding Member of this Institute, a very interesting account of some recent developments in radioactive methods of determining the age of minerals and, therefore, of the rocks in which they occur. It deals in particular with studies of the minerals of certain pegmatite dykes on the Huron claims and Bear claims in southeastern Manitoba, which, the results indicate, are among the oldest rocks of the earth&apos;s crust. The following article presents a non-mathematical summary of Professor Lane&apos;s paper . . It will be noted that he is anxious to obtain suitable samples of certain minerals and rocks for further age studies. We hope some o our members may be able to supply him with the material he needs. It may be well to explain briefly how the age determinations are made. Uranium is continually breaking down, or disintegrating in successive steps through radium, etc., to a final product which is lead (uranium-lead), and the rate at which this change takes place is known. Minerals containing uranium will therefore contain lead also, and the lead-uranium ratio mul-tiplied by a certain factor (approximately 7 ,600) will give the age of the mineral in millions of years. Thorium also disintegrates at a known rate to give lead (thorium-lead) as a final product, and the age of a mineral containing thorium can thus be calculated from the lead-thorium ratio. Thorium breaks down more slowly than uranium. In unit time, one gram of thorium produces about as much lead as 0.36 grams of uranium.-ED.

Jan 1, 1938

By Jack Craft

Local Environment Atmospheric conditions (or lack thereof) Drilling fluids are impractical Cuttings removal is a major concern Heat dissipation is a major concern Some tried-and-true mechanisms need air to function properly Gravity Low gravity means low downforce Microgravity means even less downforce Regolith Local dust may be highly abrasive Packaging for Spaceflight System mass is highly constrained The drill must fit within the spacecraft?s launch envelope Power is constrained

May 1, 2013

By George J. Cymerman

Since 1978, Syncrude Canada Ltd. has been expanding steadily its oil sand mining and processing capacity while reducing unit energy requirements. At the current rate of ~180 M tonne/year oil sand, the originally adopted Karl Clark?s 80°C version of the Hot Water process would require some 53 PJ (53 x 1015 Joule) heat. If this amount of heat were to be derived from burning natural gas it would cost $369 M/y (at $7/GJ). Fortunately, effective recovery of waste heat from the upgrading operations at the Mildred Lake site obviated the need for water heating with natural gas. The oil sand hydrotransport technology, first utilized commercially in the mid-nineties at Syncrude?s North Mine, reduced slurry temperature from ~80°C to ~50°C, cutting the unit heat requirement from 293 MJ/tonne to 183 MJ/t. However, in the new 100 Mt/year Aurora Mine even a 50°C process temperature would still require 18 PJ of heat energy per year. Only limited quantity of 65°C water could be imported from Mildred Lake site and some waste heat would be available from Gas Turbine Generators. A new, Low Energy Extraction (LEE) process was developed to minimize heat requirements by further reducing process temperatures to 25°C in the slurry pipeline and 35°C in the Primary Separation Vessels (PSV). Unfortunately, when applied to certain ore facies in Aurora, the LEE process yielded disappointing bitumen recoveries, necessitating an increase in slurry temperatures from 25°C to 35°C in the pipeline and from 35°C to 42°C in Primary Separation. In 2004, an Optimized Low Energy process (OLE) was developed and piloted at Syncrude Research using a 2000 kg/hour pilot plant. In the OLE process, most available heat is applied up-front to produce 45°C pipeline slurry at a density of 1.58 kg/l. Once the pipeline conditioning process is completed, the slurry is flooded with cold (10°C) water, resulting in PSV temperature of 34°C. The overall heat and water requirements are the same, or slightly lower, compared to those of the LEE process ? but without the penalty in bitumen recovery. Processing 100 Mt oil sand at 34°C (96 MJ/t), rather than at 50°C (183 MJ/t), will save $61 M/y (@ $7/GJ) and reduce green house gas emissions by ~47 %. The OLE process is currently being implemented at the Syncrude Aurora Mine.

May 1, 2006

By Fr. -W. Bach

In the past years the enormous weight saving potential of magnesium sheet has been demonstrated by various research projects all over the world. It has been shown magnesium flat products can benefit automotive, aviation, machine tool and consumer electronics industries. Major material problems such as poor formability, corrosion resistance and high production cost still inhibit the application of magnesium sheets in large scale production. The present contribution outlines achievements in casting and rolling technology. The authors developed an adapted strip casting process in which near-net-shape rolling feedstock of several wrought alloys has been produced. During the rolling process, various parameters were varied in order to modify the microstructure and surface quality of sheet. Several temperature cycles, strains, lubricants, roll surface structures and roll coatings have been analyzed. The sheets were examined and tested in deep-drawing experiments. Suitable rolling schedules have been developed for standard and modified wrought alloys. The study concludes with an overview of current industrial solutions and an estimation of the potential cost savings that might result from the adaptation of the process that has been developed.

Jan 1, 2006

By I. Masters, K. Buban, M. Faris, M. Antonio, M. Collins

"AngloGold Ashanti Brasil, with assistance from Sherritt International Corporation, has recently commissioned a new autoclave for the pressure oxidation of refractory gold feeds at their Corrego do Sítio operation in Brazil. Design of the new plant, including feed acidulation, pressure oxidation, oxidized solids washing and solution neutralization circuits, was based on the results of test work conducted by Sherritt at their pilot plant in Fort Saskatchewan, Alberta. This paper describes the results of the pilot plant study as well as highlights of the design exercise.INTRODUCTIONAngloGold Ashanti Brasil (AGA Brasil) has recently commissioned a refractory gold pressure oxidation plant at the site of the original São Bento operation in Brazil. The design of the São Bento pressure oxidation facility was based on Sherritt technology; Sherritt carried out the original process development test work in the mid-1980s, provided a process design package and detailed specifications for critical pressure oxidation equipment and participated in the training of operators and commissioning of the plant. The São Bento plant was operated between 1986 and 2007, when the original ore body was exhausted (Silva et al., 2004). AGA Brasil purchased the facility from Eldorado Gold in 2008, with the intent of refurbishing the plant to process refractory gold concentrates produced from the nearby Córrego do Sítio mining area.Sherritt International Corporation has a long history in the development and application of commercial pressure oxidation and pressure leaching processes. Sherritt’s development of technology for the pressure oxidation of refractory gold ores and concentrates commenced in the 1980s in collaboration with Homestake for application at the McLaughlin project in California. This was followed by several commercial applications in Canada, Papua New Guinea and Brazil (Berezowsky et al., 1991). More than thirty pilot plant campaigns investigating the pressure oxidation of refractory gold ores or concentrates have been conducted by Sherritt since the 1980s, and projects with Sherritt contributions to the process development studies and/or engineering design account for about half of the commercial plants that have operated to date with this type of process (Collins et al., 2011a; 2011b)."

Jan 1, 2012

By B. McKevitt, P. Abbasi

The ion exchange process (IX) is applied in the mining industry for the removal of impurities from process streams, treatment of waste solutions prior to disposal and the recovery of valuable metals. Extensive studies have been performed with the goal of modeling of IX for the case of a single metal loading onto iminodiacetic resin in the hydrogen form. However, in a real system, a resin may be saturated by impurities (iron, calcium, magnesium, manganese), which are then displaced by the metal of interest. The present study provides an insight into the Fe2+ loading process onto iminodiacetic ion exchange resin under the infinite solution volume condition. The study involves the measurement of iron loading under a variety of experimental conditions as well as an attempt to model the loading process using the hybrid correlation advanced by McKevitt (2012). The importance of the experimental and modeling work are discussed in the context of resin in pulp recovery of nickel.

Jan 1, 2014

By A. Manouchehrian, M. Cai

"Rockburst, which often occurs around underground openings in highly stressed hard rocks, is a sudden and violent unstable rock failure and is associated with energy release. Rockburst is very dangerous to workers and mining equipment, and it has been a major concern for deep underground construction and mining. Before excavation, rocks are loaded under a true-triaxial condition. Upon excavation, the rocks at the excavation boundaries are loaded in the maximum principal stress direction and unloaded in the minimum principal stress direction and this provides a necessary condition for unstable rock failure to occur. Understanding rock behavior under true-triaxial unloading condition is critical for developing measures to control unstable rock failure in underground construction.In this article, an explicit FEM tool is used to simulate rock behavior under true-triaxial unloading condition, with a focus on analyzing stable and unstable failure and the released energy during failure. Firstly, a uniaxial compression test was simulated. The results indicated that the adopted numerical tool was able to simulate stable and unstable failure by varying the Loading System Stiffness (LSS). In this research, Loading System Reaction Intensity (LSRI) was proposed as an indicator to identify stable and unstable failure. Secondly, unstable rock failure under true-triaxial unloading condition was simulated. A rock specimen was loaded in three directions; the lateral pressures (s3 and s2) were kept constant and the vertical stress (s1) was increased to a pre-defined stress. The specimen was suddenly unloaded in the minimum principal stress direction (s3) and loading in the s1 direction was continued until failure occurred. Different LSS values were considered and the results showed that the LSS influenced the failure mode; a soft loading system resulted in more violent failure and released more energy than that in a stiff loading system. The influence of specimen height to width ratio on rock failure was also investigated. It was found that failure in taller specimens was more violent than that in shorter specimens. Insights gained from the simulation are useful for better understanding of the influencing factors on the released kinetic energy during unstable rock failure and to find means to control rockburst damage in engineering practice."

Jan 1, 2015