Search Documents

By A. Michalkow

DELN ITE Mines Limited is located in Deloro township, on the west end of the south break of the Porcupine Camp. Mining operations are currently being carried out on the downward extension of a system of quartz veins in an andesite zone. This zone has been followed from surface to the present bottom level of 5,250 feet. The changing mineralogy of the vein system has involved an increase in tourmaline content from the surface downwards, so that the veins at the lower levels are composed of dark brown quartz-tourmaline. The drilling problem presented by these extremely hard veins was partially alleviated by the development and adoption of a one-inch drill bit. All blast-hole drilling is now done with the one-inch bit, without any difference in hole spacing.

Jan 1, 1962

By E. Krause

The oxidation of Fe(II) with S(IV) and oxygen can be used advantageously in leaching systems requiring both Fe(III) and sulfuric acid; e.g., heap leaching of sulfide-containing ores or concentrates. The oxidation of Fe(II) with SO2/air is several orders of magnitude faster than with air alone; rates of up to ?20 g/L'h were observed at 25°C. The reaction proceeds via an intermediate orange-red mixed-valence Fe(II)/Fe(III) sulfite complex, which is present at an essentially constant concentration throughout most of the oxidation process. The oxidation rate of Fe(II) is approximated by the formula -d[Fe(II)]/dt = k [S(IV)] [02]0'3. The concentration of the mixed-valence complex, and thus the iron oxidation rate, decreases with increasing acidity. Certain impurities, such as SCN- and thiourea, negatively affect the rate. The oxidation reaction 2Fe2 + SO2 + 02 4 2Fe3+ + S042- is accompanied by the side reaction H20 + SO2 + 1/202 4 H2SO4. The side reaction becomes particularly important at low temperatures and whenever the oxygen mass transfer is insufficient with respect to the rate of addition of S(IV). Thus, effective oxygen mass transfer is essential for achieving high oxidation rates with minimal acid formation. The activation energy was estimated as 141 kJ/mol over the temperature range 10-35°C.

Jan 1, 2006

By A. Romero

"Most underground mines require heating or cooling systems to meet health and safety standards in the working areas. In regions where daily or seasonal fluctuations of environmental conditions exist, these systems tend to be over-sized and operate at low average load factors, which increase both investment and operating costs. One possible approach to reduce the temperature variations of the fresh air supplied to the mine, and so reducing the investment in large heating or cooling systems, is to use rock as a thermal regenerator or thermal storage system. Packed rock beds act as thermal inertial units, damping the atmospheric temperature oscillations to provide a more constant fresh air temperature. However, although regenerators exist in some mines, and packed bed rocks have been studied in detail in solar thermal power applications, there is a lack of tools to design new and sufficiently large storage systems of this kind. This work fills the existing gap by presenting a methodology to design and evaluate the impact on the ventilation systems of these regenerators. The method is validated using existing rock bed systems found in the literature and illustrates possible designs for small and large size regenerators in both hot and cold climates.1 INTRODUCTION “ It is quite amazing how often answers to extremely complicated problems can be obtained in this way, by using greatly simplified models of the real situation for the purpose of calculation.” Whiller, A. in private communication to J. S. Stachulak (1989). Motivation Most underground mines located in regions with extreme climatic conditions require the thermal pre-treatment of the fresh ventilation airflows, whether for heating or cooling. Heating commonly is needed in sites with sub-zero temperatures and is usually effected by direct or indirect burning of natural gas or propane. Alternatively, cooling is required in areas with hot temperatures, or in mines with high underground thermal loads where the fresh air at ambient temperature cannot provide enough refrigeration. Thus, when the ambient air conditions cannot provide by itself enough thermal power to ensure safe underground working conditions, a heating or cooling plant is required, which involves a considerable equipment and operation cost."

Jan 1, 2019

By K. Ebrahimi-Nasrabadi

The dependence between the extent of conversion of cryptocrystalline magnesite to caustic magnesia was studied experimentally in the temperature range of 400?1200 °C and for calcination times up to 8 h. A TGA?DTA analysis showed that decomposition begins at temperatures as low as 340 °C and is completed at 600 °C. Measurements of specific surface area (SSA), iodine adsorption number (IN), crystallite size, and loss on ignition were carried out to characterize the product quality. It was found that while all the parameters are dependent on the extent of calcination, densification of the product caused by grain coarsening affects their final values. As a consequence, SSA and IN went through a maximum with time. The study showed that high quality caustic calcined magnesia can be produced in a narrow range of temperature (600?650 °C) and time (1?4 h). Medium quality caustic calcined magnesia can be made within a wider range of parameters.

Aug 1, 2013

By Edouard Asselin, Tasawar Javed

This study was conducted as a part of ongoing work to characterize sulphide concentrate leach residues generated under CESL (Cominco Engineering Services Limited) and Vale pilot and demonstration plant medium temperature (150 °C) process conditions. Three different samples were analyzed. Derivative samples were prepared by extracting gypsum, sulphur and amorphous/poorly crystalline iron oxyhydroxide phases from the leach residues. Thermal behavior of the samples was studied by thermal gravimetric analysis (TGA) and differential thermal analysis (DTA) in the temperature range 25 to 800 °C in both air and nitrogen atmospheres, with XRD analyses both before and after heating. Thermal transformation temperatures for different iron oxides/oxyhydroxides present in hydrometallurgical leach residues vary over a wide range which suggests the variable crystallinity of the phases. Raman spectroscopic analysis was carried out to help identify the type of iron phases in the residues. Furthermore, hydroxylamine hydrochloride (HaHC) and oxalate extractions were used to compare the fractionation of the amorphous/poorly crystalline iron phases in the residues. Given the compositions of the residues, any thermal events in the temperature range of 200 °C to 480 °C were attributed to amorphous/poorly crystalline iron phases.

Jan 1, 2014

By O. Lundhede

Today, systems and machinery usually are designed to meet only one specific customer?s requirements. One reason for this is that underground automation and smart functions are often developed tightly together with a customer. This is natural, since risk and cost can be shared between the customer and the supplier. Nevertheless, when the automation product develops and the market increase this will cause problems: The highly specialized products will not fulfill the next customer?s demands. In order to cope with this problem, Atlas Copco works towards a common platform. Instead of designing solutions for specific customers, we will lift the abstraction and focus on standardized modules. These modules, or function blocks, can then be combined in a large variety of configurations. The benefits of combining modules into products are, for example: increased flexibility when options are available for many machines; easier commissioning and maintenance since less different spare parts and tools are needed; and easier operation since the user interfaces have a similar look and feel. This paper will present the ongoing work towards standardized modules. We will discuss how our Rig Control System (RCS) allows for modular design at Atlas Copco. RCS has number of standardized modules that are used in different surface and underground mining and tunneling equipment. These modules are also used for optional products such as, drilling, radio-remote control, and telematics systems.

Aug 1, 2013

By G. Song

Magnesium has excellent bio-compatibility in terms of its density, strength, elastic modulus and toxicity. However, due to its poor corrosion performance, so far magnesium has not been successfully used in the human body as a permanent implant material. Nevertheless, there is a possibility to utilize the low corrosion resistance of magnesium to make magnesium into a temporary implant component that can gradually dissolve in the human body after surgical region heals. This will avoid the secondary operation to remove the temporarily implanted component and the chronic inflammatory discomfort caused by the implant. This paper is aimed at exploring the possibility of using magnesium as a degradable bio-material through investigating the corrosion behaviors of pure magnesium and surface treated magnesium in a simulated body fluid (SBF) solution. It was found that magnesium corroded rapidly in the SBF solution, resulting in vigorous hydrogen evolution and a strong alkalization effect. Hence, it is impractical to use magnesium as a permanent implanted material or even a degradable implant. However, a proper anodizing treatment can significantly improve the corrosion resistance of magnesium, and hence slower down the hydrogen evolution and alkalization processes, which will allow to control the corrosion or degradation of magnesium at a desired rate in the human body. With a controllable corrosion rate, it is believed that magnesium as a degradable implanted material will be eventually achievable.

Jan 1, 2006

Open pit production planning is a procedure consisting of multiple stages. Although all the planning stages rely on the geostatistical block models, long- to short-term plans each require their appropriate resolutions and levels of details. The main motives behind using different resolutions are the tractability of the models and the practicality of the generated schedules. The current approach in the mining industry is to use nested pits generated by Lerchs-Grossman as the basis for long-term planning and to use manually generated polygons, within those pushbacks, as the units of production control in mid- and short-term planning. However, the nested pits generated by Lerchs-Grossman algorithm and the polygons drawn by mining engineer do not provide control over the value and tonnage of ore and waste inside the planning units and therefore cannot lead to optimum solutions. In this paper, we first present a pushback determination approach which maximizes the profit of the mine with control over the tonnage of ore and waste within each pushback. We then propose a clustering approach with size and shape control that determines aggregates within those pushbacks; and finally, we introduce a mathematical programming model which uses the generated pushbacks and aggregates as the planning basis and generates production schedules that maximize the net present value of the operation and are practical from the operation?s point of view.

Aug 1, 2013

By K. E. Waters, E. R. L. Espiritu, G. R. da Silva

"Rare earth (RE) elements are essential components of emerging green technologies. The increase in demand for these applications have driven the search and development of new rare earth deposits such as the Niobec project in Quebec, Canada. This deposit consists primarily of dolomite with significant amount of RE minerals bastnäsite and monazite, the primary sources of RE elements. Due to the minerals’ fine liberation sizes, flotation is commonly used as a concentration method. To develop an efficient process, the electrokinetic properties of the minerals must be understood. In this study, the surface properties of bastnäsite, monazite (RE minerals) and dolomite (a common gangue mineral) were investigated by zeta potential measurements. These measurements are affected by various ions present in solution; for bastnäsite, monazite and dolomite, some of these ions are H+, OH-, PO43- and CO32-. Dolomite, being a sparingly soluble mineral and a primary component of the ore, may be the greatest contributor of these ions in solution in the form of CO32- ions. Thus, different sources of CO32- ions (from dolomite dissolution and from Na2CO3) were investigated. The research work aims at elucidating how these reagents may influence the minerals’ surfaces. The results have shown that dolomite supernatant and sodium carbonate greatly affect the electrokinetic properties of each minerals. The addition of dolomite supernatant have resulted to relatively similar zeta potential of the minerals; while, sodium carbonate have affected them differently. These observations could be useful in efficient flotation of bastnäsite and/or monazite from bastnäsite-monazite-dolomite system.INTRODUCTIONThe increase in the demand for rare earth (RE) elements has driven the search and development of new deposits. Out of 53 rare earth projects in the world, 19 can be found in Canada (Hatch, 2015). These include the Niobec project of Magris Resources Company in Quebec. This deposit contains a significant amount of rare earth minerals (such as bastnäsite and monazite), with carbonates (such as dolomite) as the primary gangue minerals."

Jan 1, 2016

By Holt. Grover J.

"IntroductionThe history of iron ore production in the United States has followed a pattern not far different from that set in the production of non-ferrous ores; the first interest of the prospector and miner being the discovery and development of high-grade ores. In the early stages of development of most mining districts, high-cost low-grade ores are usually of slight interest due to the additional capital investment required in concentrating plants, as well as the increased requirements of •power and other facilities. As the reserves of higher grade ores are depleted and the technical knowledge of ore beneficiation is broadened, production of concentrates from the lower grade ores is stimulated.The real stimulus necessary to arouse serious consideration of beneficiated iron ore in the Lake Superior district has been provided by the serious inroads made in the high-grade ore reserves by two World Wars.The first shipment of high-grade iron ore from the Mesabi range in Minnesota was recorded in 1892, and the first token shipment of concentrates was made 15 years later, in 1907. Not until 1910 did the production of concentrates assume any great importance. A steady increase in concentrate production over the years is shown by the fact that, in 1910, concentrates accounted for 8 per cent of the total shipments from the State, whereas by the time of World War II this percentage had increased to 22 per cent and by 1948 had risen to 26 per cent. It seems a safe assumption that the shipment of concentrated iron ore, from the Mesabi range in particular, will continue to increase even more rapidly from now on, with other iron ranges of the Lake Superior district following this lead."

Jan 1, 1950

By V. I. Ryaboy, V. P. Kretov, I. V. Ryaboy, E. D. Shepeta

This paper studies the features of known and newly synthesized dialkyldithiophosphates and reagents with thioamide groups when separating copper-containing and arsenic-containing minerals in the flotation of skarn-scheelite-sulphide ore at the Primorskaya concentration plant. The optimization of dialkyldithiophosphate collectors was based on the study of their surface activity at the liquid-gas interface and estimated hydrophobic abilities. The flotation experiments show that the selectivity of action of the reagent increases with an increase of its surface activity and a reduction of hydrophobic ability when separating chalcopyrite and arsenopyrite. IMA-225-5 was proposed as a more efficient dialkyldithiophosphate collector, which increases the recovery of copper by 2.8% compared to the industrially used collector IMA-I413. Selection of the optimal structure for reagents with thioamide groups (derivatives of thionocarbamate and thiourea) was carried out according to their acidity and the presence of hydrophilic particles in their structure. Calculations were performed depending on the pH of the solution of chalcopyrite to determine the optimum reagent sorption and to further optimize the structures of these reagents. The tests with reagents with thioamide groups show an increase in copper recovery by 3-4% together with a significant increase of arsenic content compared to IMA-225-5. As a stronger collector with thioamide groups, it was recommended to use sample 234, which belongs to the thiourea derivatives. IMA-225-5 was recommended for industrial tests at the Primorskaya concentration plant. Thus, this study has shown that using dialkyldithiophosphate is more appropriate if it is necessary to increase the selectivity of separation of copper-containing and arsenic-containing minerals, and using reagents with thioamide groups, or their combinations with dialkyldithiophosphates, is more appropriate if it is necessary to increase the recovery of copper or the quality of copper concentrate with less selectivity of the process.

Jan 1, 2016

By R. Roufail

"Energy consumption in stirred mills has been studied, in the last couple of decades, on a macro scale. Effective operation and meeting particle size required for downstream operations used to be the main objectives behind energy utilization of stirred mills. In this paper, three energy terms are defined to assist in understanding the breakage mechanism for various types of minerals versus mill operation. The types of minerals studied had diverse physical and mechanical properties that are summarized as specific gravity, hardness and crystal structure. The minerals utilized in this study were quartz and galena. The effect of quartz and galena mix has been addressed as well as Lead-Zinc ore sample from SAG mill discharge. The energy input to the mill is function of the agitator speed, therefore three agitator speeds were evaluated, 1000, 1500 and 2000 RPM, respectively. The energy terms studied are specific energy (kWhr/ton). Effective energy is the ratio between net energy and total energy consumed by the mill. Last type of energy is the specific breakage energy, which is the net energy consumed by the mill per one-micron breakage. Results showed that specific energy and specific breakage rate are functions of mineral type, while effective energy is only function of mill input power (agitator speed).INTRODUCTIONGrinding is the largest energy consuming component of a mineral processing operation and typically consumes about 50% of the total energy used at a mining operation (Botin, 2009). Over the last two decades, stirred mills have been extensively utilized in mineral processing operations due to increased mineralogical complexity of ore bodies. Stirred mills grind particles to less than 10 µm by applying a high power intensity. The technology has been the focus of several research studies to investigate mill energy and grinding mechanisms. Becker, et. al. (2001) studied the relationship between different types of energy including input energy, specific energy, volume/mass specific energies, to stress intensity and final product particle size. Other studies such as by Kwade (1999), Kwade and Schwedes (2002), Blecher et al (1996), Partyka and Yan (2007), Stender et al (2004), focused on mill design and/or stress intensity distribution. Peukert (2004) studied the effect of mechanical properties of the grinding media and ground material on the comminution process."

Jan 1, 2016

By D. Raicevic

Interest has recently been revived in the recovery of tantalum from the Bernie Lake pegmatite deposit. A gravity concentration process was developed to give satisfactory recovery and concentrate grade. The application of high-intensity magnetic separation was also stud1ed. A pilot-plant investigation that confirmed the laboratory testing and provided a commercial-grade concentrate 1s described.

Jan 1, 1968

By K. Musgrave

"The ISO 9000 Quality Management System Standards have become internationally accepted as the way to manage quality assurance. The author has developed a Maintenance Management System Standard using ISO 9001as a model and is working with a major basemetal mining company to implement this. This paper describes the structure of the standard and the steps required for its implementation.Using a management standard ensures that a system is maintained, reviewed by internal audit, and when instances of failing to follow the procedures (nonconformances) occur, that corrective action is taken. It also ensures that regular reviews are made and that the sys-tem is continuously improved.The Standard is designed so that if an organization decides to register to an ISO 9000standard, the Maintenance Management System will be in a format that is compatible and can be incorporated with little effort into the Quality System.IntroductionIn reviewing maintenance operations at many mining companies, and often seeing those same organizations some years later, two recurring issues have been noticed..The first issue is how dependent effective maintenance is upon individual supervisors and crews. In one situation, a mine that had an excellent maintenance system in the 1980s. Now, with new supervisors and crews, it is starting to develop a system that will bring it back to where it once was. No written procedures remain from the earlier excellent system.The second issue is that most operations feel that maintenance is the sole responsibility of the maintenance supervisors and crews. Nothing could be further from the truth. Maintenance, like safety, is everyone’s responsibility. If the operator does not report problems and perform daily checks, and if the production supervisor runs equipment until it fails, then nothing the maintenance crew does will prevent emergency breakdowns and lost production. More importantly, equipment will be operated in unsafe conditions, putting employees at risk and, with today’s regulations, leaving supervisors open to prosecution.The Maintenance Management System outlined in this paper is designed to establish the present best practices as standard procedures, to provide a continual review so that these practices are improved in the future, and to identify instances where the system fails so that corrective action is taken. The mine referred to above is using this approach to make sure that, this time, the system it implements will survive."

Jan 1, 1997

By Meifeng Zhi, Yuqing Niu, Xixin Chang, Fengqi Zhao, Weimin Qiu, Hao Wang, Zhenqian Wen, Zujun Shu

An applicable Eluex process was developed for acid in-situ leaching (ISL) uranium mine in Bayanwula. In this process, uranium was adsorbed with strong base anion resin from the pregnant solution, then the loaded resin was eluted by sulfuric acid. After D2EHPA extraction, the concentrated eluate was enriched, and the loaded organic phase was stripped by sodium carbonate. The yellow cake was obtained by sodium hydroxide precipitation at last. The uranium concentration in the loaded strip solution was 52.8 g/L. Parameters of the process were determined, and the impact of the Eluex process in underground leaching was also investigated. In industrial design, 95% of raffinate went back to elution and 5% back to in-situ leaching. No significant effect on uranium leaching or resin adsorption was found.

Jan 1, 2020

By Jun Deng

The aim of this paper is to study the scientificity and reliability of three coal gas indices used to predict coal fire disasters, namely Graham?s ratio, CO/CO2 ratio, Litton ratio and their different characteristics and service conditions. Data from a programmed temperature experiment were applied to check their veracity and accuracy. Each index performed well in detecting the level of a fire. We conclude that it is better to redefine the definition through experimentation before applying a given index. Integrated analysis of the results can provide reliable reference data for predicting spontaneous combustion of coal.

Aug 1, 2013

By J. P. Messervey

THE story of the efforts made by the Department of Mines of Nova Scotia in the search for and investigation of mineral resources for the Canadian war effort began in the spring of 1937. During the past five years, however, heavy enlistments in the Active Service Forces by employees of the mining industry of the Province caused a recession in the production of coal, salt, and other essential minerals required to keep industry rolling on a wartime basis. A marked increase was shown during the period in prospecting for 'strategic' minerals, not only by individuals but also by some of the foremost mining companies. The Provincial Government offered encouragement in this field of endeavour by the enactment of legislation whereby the prospector was enabled to secure the maximum area of ground in a prospecting license at a minimum of cost. The labour requirements on the ground staked, however, remained unchanged. The Nova Scotia Department of Mines continued active investigation of minerals vital to the war effort. These included fluorspar, barytes, diatomite, limestone, and coal. Fundamental knowledge concerning the geology and mode of occurrence of these minerals was accumulated and extensive diamond drilling was carried out on the promising occurrences. Work in these fields is being continued.

Jan 1, 1945

By A. R. Farkoosh, J-P. Fortin, M. Pekguleryuz, S. Bagherpour

"Titanium aluminides are structural intermetallics which offer an attractive combination of high temperature strength and light weight. For such properties, these intermetallic alloys have become front-runners in replacing nickel-based superalloys used for several high temperature applications. These alloys are produced from metallic titanium, aluminum and master alloys involving an expensive and difficult process. A low cost alternative to current industrial production method is the new modified aluminothermic process which directly reduces titanium oxide (TiO2) to titanium aluminides. Nevertheless, this process has itself significant challenges in achieving alloys free of oxide inclusions; the close densities of the slag and the titanium aluminides makes slag/molten metal separation a challenging task. Usually, the alloy produced requires a second refining step. In this study, thermodynamic calculations based on CALPHAD method were performed to determine the solidification path and an attempt has been made to develop a criterion to increase the density deference between the slag and the alloy by alloying with appropriate elements. Furthermore, scanning electron microscopy (SEM) and x-ray diffraction (XRD) techniques were utilized to examine the microstructure and phase selection of three Ti-Al alloys produced by the aluminothermic reaction, including the as-cast, refined in a controlled atmosphere and inert-gas-refined alloys. The composition range of the alloys studied was restricted to the a2-Ti3Al + ?-TiAl phase field (Ti-30Al) in the binary Ti-Al phase diagram leading to a lamellar structure with different complex intermetallics as shown in Figure 1.INTRODUCTIONTiAl based alloys are promising structural materials for high temperature aerospace and automotive applications. This is due to some attractive properties such as low density, high specific strength, high specific stiffness and high temperature strength retention (Wen-bin, Xue-wen, Hong-fei, & Yong-feng, 2011). These alloys have become leading candidates to replace Ni-based super alloys in gas turbine engines. Replacement of Ni-based super alloy parts with titanium aluminides is expected to reduce the structural weight of high performance gas turbine engines by as much as 20–30% (Kothari, Radhakrishnan, Sudarshan, & Wereley, 2012)."

Jan 1, 2016

By Yan-Jun Shen

The rock mass classification system, BQ (basic quality), is the only national system that is suitable to most kinds of rock engineering in China. It uses two main aspects of the rock mass, the intact uniaxial compressive strength (UCS) and the rock intactness index (KV), to obtain the rock mass BQ. The index KV could be measured by the acoustic wave method. However, because this method is an indirect approach to characterize the rock mass structure, misfits often occur between the test results and the actual rock mass characteristics. Therefore, a new parameter KGSI expressed by the geological strength index is proposed to replace the original KV, and a new method is presented to express the value of BQ as a function of the UCS and the KGSI. Then, the underground excavations at five hydropower stations were chosen as examples to study the relationship between the revised BQ and the each of the international systems (RMR, Q or RMi). In addition, the applicability of the RMR, Q, or RMi system is discussed for China?s rock characteristics and geological conditions, and suggestions are given for improving the revised BQ system.

Aug 1, 2013

By M. C. Bétournay, J. E. Udd

"The legacy of abandoned mines in Canada creates issues that impact on both the health and safety of Canadians and the environment. Solutions to the problems of abandoned minesites require a detailed understanding of site conditions, the engineering solutions which may be relevant, and planning for effective use of the land. In this paper, the authors outline the basic thrusts that have been developed at CANMET to address this problem. These include: multiprovincial agreements to develop a national database; methods of site rendering; a ten-year research program to develop engineering approaches; the review of a large number of case studies; and outlining the associated risks. Examples of the applications of this research are provided in the areas of: municipal, provincial, and federal co-operative projects; site-specific applications; and international linkages."

Jan 1, 1997