Search Documents

By Karina Forster

Open stope design depends on the ore body geometry, loading conditions and rock mass properties to estimate stope dilution and ground support requirements. Rock mass conditions for design primarily rely upon estimates of well established rock classification systems. Many sources of data exist for obtaining estimates for these rock mass classification values which include core logging, geotechnical mapping, geological mapping as well as linking one classification system to another through the use of empirically derived equations. The extent of mapping coverage can also vary significantly based on the data collection technique. This paper proposes an approach where individual components of rock mass classification systems are collected by the different available data collection techniques. Data from different rock types are also considered separately based on their alteration characteristics and general observation products. Data from the Cameco Corporation Eagle Point Mine is presented and an approach is outlined for obtaining average representative classification values for stope hanging wall characterization. The effectiveness of this approach is demonstrated through the analysis of a data base of hanging wall dilution information.

Jun 1, 2012

By L. J. Cabri

A gold sample assaying 11.4 g Ault was selected for this study. Approximately 99% of the gold in this sample occurs as discrete gold minerals; the balance occurring as invisible gold in pyrite (determined by SIMS analysis). The sample was coarsely ground and sieved, yielding -38, 17, 22 and 22 wt.% in the -400+160 um, -160+80 um, -80+40 µm and -40 µm size fractions. Assays of the size fractions gave a gold distribution of -32, 20, 21, and 27% respectively. Processing with the hydroseparator (model HS-02) gave two tailings products and one concentrate from each size fraction. Assays of the concentrate from each size fraction gave gold recoveries of -7, 7, 24, 19%, respectively. Polished sections were prepared from each hydroseparation product and studied by image analysis to automatically search for gold minerals. Calculations were done using the surface area of the grains of gold minerals found on the polished sections.

Jan 1, 2005

By I. Spector

A SHORTAGE of cement in the Prairie Provinces, together with an aggressive policy on the part of the Saskatchewan Government in bringing new industries to the province, combined to create a favourable set of conditions for the establishment of Saskatchewan's first cement plant on the outskirts of Regina. Built by Saskatchewan Cement Corporation Limited, this single-kiln plant, tl1e latest addition to cement producers on the Prairies, began operations in the Fall of 1956. Location of the plant followed the trend of building cement manufacturing facilities in market areas rather than at raw material sources. In 1957, all assets of the Corporation were taken over by Inland Cement Company Limited and the plant and quarry now operate as Saskatchewan Cement Company, an Inland division. The Regina plant's production makes up approximately eleven per cent of the productive capacity of all plants in the Prairie Provinces. At present, two types of cement are manufactured -normal portland and sulphate resisting.

Jan 1, 1960

By Xiao min Zhou, Yan Xu, Hongzhen Liang, Xiaonan He

"With the increase of shaft excavation depth, the thickness of the shaft lining increases sharply. It is difficult to reduce thickness of lining effectively by improving high-strength concrete performance. The concept of the New Austrian Tunneling Method (NATM) is that surrounding rock plays a certain role in tunnel support. The solution should be to find the correct relationship between shaft lining thickness and rock strength, which is related with the interaction between the surrounding rock and concrete lining. The plane strain mechanics model is introduced to calculate lining thickness. Shaft lining design of Cixi Colliery in China is completed with the mechanics-based method proposed in this study. The lining design is verified through numerical simulation and field monitoring. The simulation results show that the maximum mises stress is located at the inner edge of the shaft lining. The increase of lining thickness cannot effectively reduce concrete grade. The monitoring results indicate that a lining design thickness of 900mm with C60 concrete, is safe and reliable in the shaft over 1000metres.This analytical design method can well be referenced in similar deep shaft projects.INTRODUCTION The New Austrian Tunneling Method (NATM), thought to have helped revolutionize the modern tunneling method, is the most extensive design philosophy and construction principle in today's tunnel engineering. It began to attract attention in the 1960s based on the work of Ladislaus von Rabcewicz, Leopold Müller, and Franz Pacher in Austria[1]. NATM was originally developed for tunneling in depth and in high situ-stress conditions in the Alps. The history of sequential excavation was reviewed, which highlights the progress of tunnel design and construction in Europe after NATM[2]. Structural conditions were introduced into the equilibrium of tunnels in NATM, and the additional force was estimated to stabilize the excavation of the tunnel[3].From the perspective of applied mechanics, there was no accuracy theory to explain the interaction between the tunnel structure and the surrounding ground. Numerical calculation is an effective means to study the basic mechanism of tunnel excavation[4].Based on two-dimensional modeling approaches in the past, such as NATM and other derivatives, a three-dimensional model was studied to"

Jan 1, 2019

By S. Glen

Cyanide management practices on modern gold plants are becoming more onerous, due to environmental pressures, particularly for signatories to the International Cyanide Management Code. Operations are therefore seeking to reduce levels of weak-acid dissociable (WAD) cyanide reporting to spigot discharge as well as to any eventual discharges from the tailings storage facility (TSF). Current gold industry standard processes primarily include the oxidation of cyanide by means of sodium meta-bisulfite (SMBS, or SO2) with air, Caro&apos;s acid (H2SO5) or hydrogen peroxide (H2O2). These processes require the transport and usage of expensive oxidizing reagents, along with the safety and environmental issues associated with these corrosive and toxic chemicals. Maelgwyn Mineral Services (MMS) has developed the MMS CN-DTM process, which utilizes the Aachen ReactorTM, a high-energy mass-transfer superoxygenation system, in conjunction with an activated carbon-based catalyst and no additional reagents, to increase the rate of cyanide oxidation to cyanate, the thermodynamically more stable form. Testwork conducted at the Maelgwyn Australia testwork facility in Perth Australia is described, at both pilot scale and continuous bench-scale, on a sample of tailings effluent obtained from an Australian gold plant. WAD cyanide is demonstrated to be lowered using the MMS CN-DTM process from an influent of 130 mg/L to the required levels for discharge to TSF (<50 mg/L). The continuous test results showed stable operation over three residence time turnovers. The pilot-scale results demonstrated the efficiency of the process at the reasonably large scales required for engineering cost estimation.

Jan 1, 2011

By P. R. La Pointe, J. Clark

"Studies have shown that the roof in coal mines is nearly twice as likely to fail at intersections as at entries due to enlarged roof spans, stress redistribution and other factors. However, the relative stability of intersections in a mine varies, and an improved understanding of what factors impact roof instability can lead to efficient, proactive mining practices that both enhance stability and mining efficiency.A study was undertaken at an underground longwall coal mine to develop a model to predict the stability at the intersections of entries and cross-cuts. The statistical analyses relied upon observational and measured data regarding the development of tension cracks, seepage, intersection geometry, mining practices, geological attributes and geomechanical factors at 783 intersections. Each intersection was given a NIOSH roof. Common data mining techniques, such as multivariate linear regression, multinomial logistic regression, decision trees and probabilistic neural nets, were considered and evaluated to establish correlations and associations between stability and the other variables. Two of the more successful techniques were Decision Trees and Multinomial Logistic Regression. The analyses showed that a number of factors impacted stability:• Overburden thickness (impact on stress concentration magnitudes)• Initial opening area (impact on stress concentration magnitudes)• Sulfur content (depositional environment & impact of mechanical properties, leaching effects)• Intersection type (impact on stress concentrations)• Gob distance (impact on stress concentrations)• Presence or proximity of a particular sandstone (impact on mechanical properties)• Roof bolt type and diameter (impact on reinforcement)Some factors showed no statistically significant relation to stability. These included:• Total area• Supported areaSeepage was a more problematic variable in assess. Seepage is associated with instability, but it is not clear whether seepage occurs as a consequence of instability, for example, through the creation of tension cracks, or whether the intersection has been excavated where water already exists and has degraded the rock prior to excavation, leading to greater instability.Seepage appears related to the geology of the roof rock mudstones, not the sandstones. Tension cracks in the intersections occur preferentially where the Sulfur content is below 0.9%. The Sulfur may relate to mechanical differences in the roof rock, and where the Sulfur is low, the roof is less stable, there are more tension cracks, and seepage is greater. This suggests that the weaker mudstones may be more prone the development of tension cracks, not because these rocks are more brittle, but possibly weaker.2-way and 3-way intersections appear to have less seepage than 4-way, although very few intersections overall have any seepage. This is similar to the roof stability, in which the 2-way and 3-way are more stable. 2-way and 3-way intersections have fewer-than-expected tension cracks, while 4-way have more than expected. These results suggest that four-way intersections are weaker and more prone to tension crack development, also suggesting that increased seepage results from weaker roof conditions, rather than the converse. Thus seepage appears to be mostly a consequence of instability rather than a cause and is higher where there are 4-way intersections, mudstone geology and external loading factors like depth of cover and proximity to gob that promotes crack development. The study also indicated that a better understanding of the mudrock facies could reduce uncertainty."

Jan 1, 2015

By Carl Pelletier

The Sigma-Lamaque Complex is considered a lode-gold deposit characterized by narrow vein structures, which have been mined historically by underground methods. In addition to the narrow vertical structures, mining also took place on horizontal veins, ?North Dipper? veins and dykes mineralized with sub-horizontal veins and stringers. Over the 60 + years of production, mining took place to a depth of 1.8 km. The upper portion of the deposit was considered all but exhausted, when viewed from an underground mining perspective. The year 1998 is considered a turning point for the Complex when a small open pit was mined at Sigma. The resource evaluation methods used underground were applied to surface mining, which allowed small pits to be mined. The resource evaluation method considered only the narrow vertical structures and was not well adapted to open pit mining. As a consequence, resources were consistently under evaluated. It became clear that a new geological approach was necessary to more accurately define resources (i.e., what was being mined). In order to integrate all characteristics (geometry, mechanics and chronology) of this complex lode-gold deposit, a new geological model was proposed. Due to this new approach, dating to February 2000 and updated in December 2000, the reserves evaluated in the first 180 meters now stand at 15 million tonnes @ 2.61 g/t Au (1,265,350 oz). Those reserves cover an east-west corridor extending 1,500 m by 750 m.

May 1, 2001

By J. S. De Lury

The metalliferous areas of Manitoba have been described in more or less detail. Since the descriptions were written some new prospects have come to light and considerable mining development has taken place in two or three localities. No attempt will be made in this paper to give an account of recent activities or to describe the several areas in detail. In a general way, geological conditions are similar in all metalliferous areas of the province, a similarity that invites a discussion of the prospects as a whole, the features that are common to all deposits and the reasons for their uniformity. Modern theories of metallogenesis have a direct bearing on such a discussion and an effort will be made to show their application.

Jan 1, 1925

By Yoshimasa Funakawa, Kazuhiro Seto, Akio Kobayashi

A new hot rolled high strength steel consisting of ferrite matrix and nanometer¬sized precipitates was developed. The ultra fine precipitates were identified as TiMoC2, and the strengthening by the precipitates was evaluated more than 300MPa in case of TS/800MPa grade steel. Due to the strengthening effect of the ultra fine precipitates, alloy elements for solid solution hardening can be reduced. It is notable that the steel shows very high yield strength (730MPa in case of TS/800MPa) and very high local elongation leading to excellent stretch flange formability at the same time. The mechanical properties of the steel are attractive for chassis parts and structural parts of auto body. The steel has been produced commercially, and applied to the parts successfully.

Jan 1, 2004

By M. A. Rabah

This study aims to recover europium, yttrium metals, some valuable salts or oxides from the white powder (apatite) coating the inner surface of spent florescent lamps (SFLs). Pressure leaching using sulphuric/nitric acid successfully dissolved the metals of interest. Europium or yttrium metals were obtained by hydrogen reduction of their oxides. Addition of potassium thiocyanate converted the dissolved sulphates to thiocyanates. Selective separation of Eu and Y was then carried out by solvent extraction from the thiocyanate solution. The used solvent was trimethyl-benzylammonium chloride. N-trihutylphosphate in 1 M nitric acid was used to strip the metal loaded in the organic phase. Results showed that the quality of the cleaned glass tubes of the SFL met the standard requirement for the lamp manufacture. The white powder (WP) is composed of calcium sulphate 35.2%, phosphate 61.5% and oxides of europium and yttrium 1.65%wt. respectively. Autoclave digestion of the WP for 4 h at 120°C and 500 kPa in sulphuric acid/nitric acid mixture dissolved 96.4% of yttrium and 92.8% of europium. The conversion rate of sulphate to thiocyanate was favoured at low temperature. Stripping of Eu and Y from the loaded organic phase behaved in an opposite way. A metal separation factor of 9.4 was obtained. ate recovered europium and yttrium salts were selectively separated using ethyl alcohol or dilute nitric acid. Yttrium was very soluble while europium was not. Europium and yttrium metals were obtained by hydrogen gas reduction at 850°C and 1575°C respectively.

Jan 1, 2004

By C. F. Starr

This paper deals with the various types of cable in use in mines, with special attention paid to their construction. There will be a few comments regarding the different insulants, jacketing materials and armouring used, depending on their application. Governing standards and the differences therein will also be discussed.

Jan 1, 1969

By Howard W. Tipper, Richard B. Campbell

"The Quesnel Trough is underlain by a thick sequence of mainly Upper Triassic and Lower Jurassic volcanic-clastic and sedimentary rocks that lie between the highly deformed Proterozoic and Paleozoic rocks in the Omineca Geanticline to the east and the Upper Paleozoic Cache Creek Group in the Pinchi Geanticline to the west. Broad areas of the Trough between Kamloops and Williams Lake are covered by Eocene volcanics and sediments and by Miocene-Pliocene plateau lava. Granitic intrusions were apparently mainly confined to two major episodes; one about 200 m.y. ago (coeval with the Guichon batholith) and one about 100 m.y. ago. In addition, the region includes small granitic and syenitic intrusions, some porphyritic, that may be all or partly still younger. Exposures in the region are generally small and scattered, obscured by widespread, not necessarily thick glacial deposits. This, together with the extensive Tertiary cover, makes prospecting difficult. The part of the Quesnel Trough discussed here is the direct northwest-ward extension of the copper-rich Kamloops-Merritt-Princeton region. It contains the Boss Mountain molybdenum mine, related to a breccia zone induced in a batholith of the oldest group by a younger intrusion, and the Cariboo Bell copper deposit in Lower Jurassic volcanic-elastic rocks and syenitic intrusions. The Gibraltar deposit, in a 200-m.y. intrusion, is within the Pinchi Geanticline close to the margin of the Trough. Molybdenum prospects are mainly restricted within or near the 100-m.y. granitic rocks. Copper prospects, on the other hand, are most prominent in the volcanic-elastic rocks and in the 200-m.y.-old granitic rocks, although they can also be spatially related to younger intrusions. Copper thus has a wide potential distribution.The writers believe that the region is deserving of careful and comprehensive exploration by directly applying the knowledge and techniques developed in the important producing areas to the south. All of the major pre-Tertiary geological elements seem to have potential for mineral deposits; none should be ignored. A thorough knowledge of the thickness and distribution of the Tertiary rocks and the development of geophysical methods to ""see through"" them is of particular importance."

Jan 1, 1970

By L. S. Beck

"IntroductionThe Beaverlodge District is an important mineralogenic province of pitchblende and occupies about 1300 square kilometres centred on Beaverlodge Lake near the north shore of Lake Athabasca in northwest Saskatchewan (Fig. 1). Uranium City is the main settlement of the area and is serviced by scheduled aircraft from Edmonton, some 700 km to the southwest, and from Prince Albert which lies a similar distance to the south.During the summer, boats and barges supply the area from the railhead to Fort McMurray via the Athabasca River and Lake Athabasca, a distance of about 550 km. For the past few years a winter road has been maintained across Lake Athabasca to Cluff Lake to connect with Highway 155.The topography of the area is typical of the Precambrian Shield with generally low relief and a disorganized drainage of numerous lakes separated by hummocky rock ridges, muskeg and drift-covered areas. Local topography in the area is, however, extremely rugged, particularly south and east of Beaverlodge Lake, where resistant rocks form prominent hills and ridges extending as much as 180 m above lake level. Rock exposures are abundant and form over 50 per cent of the land area.History of Exploration and DevelopmentEconomic interest was first aroused by Tyrrell (1896) who described an occurrence of iron formation at Fish Hook Bay; however, subsequent evaluation of the deposit indicated it to be uneconomic."

Jan 1, 1986

By Rodgers Peale

The Waite mine, as it is locally termed, is situated in the Rouyn district, in the townships of Duprat and Dufresnoy, Quebec, and lies about 340 miles north of Toronto. Due to the impetus given prospecting in the Rouyn district by the discovery, some years ago, of copper-gold ore on the Horne claims, many exploration parties were put into the field. Early in 1925, J. H. C. Waite, C. H. Ackerman, and T. Montgomery staked the claims which now comprise the mine beating their names. Trenching and diamond drilling soon disclosed an ore-body of commercial size and grade, and by the end of 1928 a shaft had been sunk 300 feet and the mine was producing 150 tons of direct-smelting copper ore a day. In the summer of 1925, Dr. H. C. Cooke, of the Geological Survey, made a reconnaissance survey of the property (1), and since that time work of the same nature has been done by several others. MacGregor has published some interesting data on the Amulet mine (2). Using as a background a summer&apos;s work on the Horne claims at Noranda, the writer spent the summer of 1929 at the Waite.

Jan 1, 1931

By M. Lebeuf, A. Dumais, C. Farsangi, N. Singh

The Nunavik Nickel project began ramp-up of a new ore body (Expo) in November 2014. This new deposit is significantly more competent than the previous ore type milled (i.e., the plant moved from a feed with a BWI of 12.2 kWh/t to predominantly material with a BWI of 19.6 kWh/t). Despite circuit changes made in advance of the Expo ore ramp-up (grinding media size, mill loading/power draw, and cyclone configuration) the throughput of the plant was bottlenecked at 90% of targeted throughput with multiple stoppages to grind-out the primary mill due to excessive circulating loads. During this time, the secondary milling circuit was under-utilised: therefore the focus for debottlenecking plant production became increasing the product size of primary milling. Given the scope of changes already made to the circuit, it was decided to test the mill in open circuit. The milling changes were modelled using the Molycop Tools package to identify potential problems. In the modelling and plant trial it was apparent that the ball size in the secondary grinding circuit was inadequate, resulting in pebbling. The power draw of the secondary mill was brought up to minimize pebbling and the average ball size was increased. The switch to open circuit primary milling permitted a significant augmentation in plant tonnage. While the overall grinding efficiency decreased using the open circuit configuration, the ability to increase throughput made it the clear operating choice.

Jan 1, 2016

By Ifeanyichukwu Nweke

"Aluminium rolling processing from ingots to cold rolled coils comes with a lot of challenges especially in controlling defective products in casting, hot mill and cold mill operations. Hence this study focused on reducing defects at mills and cast-house using six sigma approaches. The use of six sigma approach will help the production experts to determine the gap between its operation and world class process. Practical data from First Aluminium Rolling mills were presented and analysed and mini improvement projects were proposed based on organisation need to achieve excellence. This study encourages aluminium alloy industries to pursue process improvement projects on the basis of analysis on data obtained from their shop floor, hence ensuring that through this, recovery is improved and cost of poor quality is reduced.INTRODUCTION Engineer Bill Smith while working at Motorola in 1986 introduced a new concept in which a set of techniques and tools are used for process improvement by controlling variations (defects). These tools and techniques are explained by an acronym DMAIC. D DEFINE the problem M MEASURE the variables in the problem A ANALYSE the variables of the problem I IMPLEMENT and verify the solution to the problem C CONTROL the solution to sustain it Most times in six-sigma approach, variations in the process that results in defects and customers’ dissatisfaction are targeted at 3.4 defects per million opportunities. There are numerous methods six sigma application use to achieve quality results and innovative strategies. Improving the quality of process through these methods helps identify and reduce variations which paves way for organisational excellence. In this study, it is encouraged to use six sigma techniques to improve aluminium rolling operations and other aluminium processing activities, the benefits of such improvement concept include: • Satisfy the voice of the customer (VOC) • Minimise costs • Maximise Profits • Build Good Team • Implement Profitable Project"

Jan 1, 2018

By D. G. E. Kerfoot

In September 1945, when the Lynn Lake nickel orebody was discovered Sherritt Gordon Mines was a small copper mining company with rapidly depleting ore reserves at its single producing mine at Sherridon in the Cold Lake area of Manitoba, 100 miles north of The Pas. The company has been formed in 1927, largely through the efforts of Eldon L. Brown, a 27-year old mining engineer, with the financial backing of Thayer and Halstead Lindsley and the Gordon family. The Lindsleys were American mine promoters who had been successful in the Sudbury area, and the Gordons had extensive interests in the lumber industry in northern Ontario. Carl Sherritt, who gave his name to the company, was an American trapper and prospector who had staked the copper property and sold his interest to the new company. Carl Sherritt died in a flying accident at The Pas in 1928. The Sherritt Gordon Mine started production in 1931, shipping copper concentrate to the new Hudson Bay copper smelter at Flin Flon, Manitoba. In 1931 the price of copper was 18¢/lb. Within a year the price had fallen to 5¢ /lb and the mine was forced to close. It remained closed through the Depression years.

Jan 1, 1999

By Phillip Mackey, Elmira Moosavi-Khoonsari

L'industrie du cuivre traverse une période passionnante, marquée par une forte demande, de bons prix et l'ouverture de nouvelles grandes installations. L'année 2022 a battu des records de production de cuivre, ce qui laisse entrevoir un potentiel de croissance supplémentaire. De grands projets sont en cours, comme la technologie Double Flash à Manyar, en Indonésie, qui peut produire plus de 500 000 tonnes de cuivre par an. À Munda, en Inde, on a construit la plus grande usine de cuivre du monde, qui produit plus de 1 000 000 tonnes de cuivre par an en combinant deux phases. De plus, l’installation de cellules de flottation de dernière génération au Mexique, au Chili et dans d'autres pays témoignent de la volonté de l'entreprise d'utiliser les technologies les plus récentes [1]. L'importance du cuivre dans la transition énergétique est évidente, l'accent étant mis à la fois sur la croissance et sur la protection de l'environnement. Cela se traduit par le développement d'usines de premier ordre dédiées aux pratiques durables.

May 2, 2024

By C. Holmes, T. Holmes

Engineered-in material handling problems are responsible for significant unrealized value in mineral processing plants. At the root, is a lack of awareness and understanding of bulk material handling science and how important it is, especially in early design stages. Mineral processes add value to mined raw feedstock through physical and chemical transformations in unit operations, but only if the material can flow through them. Essentially, each unit operation receives a unique feedstock and produces a unique product to be collected, transported, and fed into the next unit operation. Such material-handling systems can only be expected to achieve design throughput if the system equipment is designed to the materials’ characteristics, over their full range of conditions. This requires quantification of flow properties to support the necessary customized equipment designs. Too often, assumptions or “library values” of a material’s properties are used as the basis for flow modelling and conceptual, and sometimes even detailed, design. This is especially true for hazardous materials like uranium ore, for which the additional precautions, costs, and time necessary for safe handling are often used to rationalize postponing or even bypassing testing. The surprises that often transpire in the wake of insufficient material handling consideration can have acute and costly effects. Fortunately, there is a better way.

Jan 1, 2020

By F. Roemer, D. Goldmann, T. Elwert

Tantalum is an important minor metal for the production of high performance capacitors. Approximately 60% of the annual tantalum production is used in this application. Despite its high price of 298 US$/kg (average price 2010–2014), at the moment, no recycling from end-of-life products takes place. In the established recycling processes of waste electrical and electronic equipment (WEEE), tantalum is lost in the slags of copper smelting, where it is highly diluted. An economic recovery is not possible at that point. Although tantalum must therefore be extracted from the WEEE stream before it enters smelting, no industrial recycling processes exist. The main reasons are its low concentration in the WEEE stream, lack of information about tantalum bearing devices, technical difficulties of extraction, and conflicts of interests regarding the recycling of other valuable metals in WEEE. In this paper, the results of a cooperation research project are presented. The aforementioned challenges are addressed and a novel tantalum recycling process is developed. Small pilot scale experiments show that a mechanical processing route can produce marketable tantalum-concentrates of 30% tantalum with yields between 60 and 70%. This is reached through a manual pre-sorting of potentially tantalum bearing products followed by a combination of an optimized comminution, sieving, air classifying, eddy-current (EC), and two stage magnetic separation. Key to the implementation of this process was a detailed survey of the tantalum concentrations in different products carried out by the industrial partner.

Jan 1, 2016