Search Documents

In April, 1961, a large pillar was removed by blasthole mining methods at Inco's Murray mine. More than half a million pounds of explosives were used to break 2,120,000 tons of ore in a single underground blast. The 5, 10 2-inch boreholes, involving 435,815 feet of drilling, were loaded over a three-week period, using conventional explosives and short-period electric caps. From this blast, more than half a million tons of ore have been removed to date (April, 1962) through slusher trenches situated in the footwall of the ore body. T HE Ontario Division of The International Nickel Company of Canada, Limited, operates six underground mines and two open pits in the Sudbury district in the north-central part of the Province. This paper describes the removal of a large pillar at the Murray mine (Figure 1), where 2,120,000 tons of ore were broken in a single underground blast by the blasthole mining method. This is the largest underground blast achieved to date (April, 1962) at Inco mines.

Jan 1, 1963

By G. Velarde

Agglomeration has as main objective to form a uniform and highly permeable heap for leaching. An inaccurate dosage of moisture during agglomeration leads directly to poor agglomerate quality and segregation of particle sizes during stacking. This causes a heterogeneous distribution of the leach solution inside the heap which invisibly and practically permanently affects the recovery. Unfortunately, only when this becomes serious and the mineral contains an excess amount of fine particles and/or clays then the poor permeability of the pile becomes obvious. This paper is based on the experience of Minera Cerro Verde in the development and application of a quantitative method to control moisture during agglomeration. As the amount of fine particles/clays varies, the quantity of moisture has to be altered in real time. The measurement of agglomerate electrical conductivity is used for it. This concept is based on the sharp change seen in conductivity when the mineral passes its absorption limit. A liquid conductive film then begins to form over the surface of the particles, which leads to the formation of agglomerates through liquid bridges, which are also electrical bridges. Moisture is adjusted to reproduce a value of conductivity established previously and is the guiding parameter. Moreover, moisture amount added to reach this conductivity parameter provides information about the fines/clays relative content for best leaching management.

Jan 1, 2004

By P. H. Tolcher

Canada, as the Free World's largest mine producer of zinc and the third largest mine producer of lead, has a vital interest in the future growth in demand for these metals. This paper traces the development of lead and zinc consumption in the last two decades, both on a total-Free-World basis and by major market areas. How Canada, as a major mine producer, has shared in this growth is also indicated. In addition, future consumption for both metals in the current decade of the 1970's is fore-cast. The demand these projections will make on Free World mines, particularly on Canadian mines, is examined. Some of the opportunities and challenges the Canadian mining industry will likely face during this period are also dealt with.

Jan 1, 1971

By G. C. Lipsyy

ALL mineral production? of Can11.da is transported in a mine car at some stage during its extraction. There are as many types and varieties of mine cars as there are of mines. Many of the cars in use were developed in the blacksmith shop. Others were designed by engineers and improved by the mine foremen and the mechanics. Every mine car has the ideas of miner, blacksmith, mechanic, and engineer incorporated in it. Many of these ideas are not generally known. This paper was written to make at least some of this information available to the mining industry. In drawings, tables, and notes, it gives all the important details pertaining to the cars. It .does not recommend any particular type of car for any particular piece of work, nor does it present drawings from which a car can be built. It gives the engineer or master mechanic information on many cars which he can apply to his own particular problems. It is hoped that this information will be of use to mine operators. If a few new ideas are conceived as a result of the paper, the author will feel that the effort of compiling it has been worth while. In order to obtain the data for the preparation of the paper, a questionnaire, copy of which is here reproduced, was sent to all the operating mining companies in Canada. An accompanying letter briefly explained the purpose of the paper and asked for co-operation in furnishing as complete information as possible.

Jan 1, 1945

By E. W. O'Brien

Personnel protection involves effective grounding and positive clearance of faults. This paper deals, in a general sense, with various schemes to achieve fool-proof personnel protection and reduce, to a minimum, the effects of human error and equipment failure.

Jan 1, 1966

By C. A. Grandison

The economic evolution from an agrarian society to an industrial and service-oriented economy is apparent to most students of history. The long-term trend is almost taken for granted, it does not require explanation — it is accepted as the nature of man to improve his standard of living. However, there are fluctuations around this trend line which have provoked a great deal of thought. The ability to understand and control these fluctuations would yield many benefits, it would eliminate economic waste and public hardship, and would no doubt make a few fortunes. I f it is not possible to control or eliminate these fluctuations, then a reasonable forecast of the tinting, rate of change and magnitude of the fluctuations would be invaluable to industry and government.

Jan 1, 1976

By M. W. Grabinsky, P. B. Tomory, J. Carvalho, J. H. Curran

Many underground mining operations use Split Set friction stabilizer bolts for rock support. Currently, however, little has been done to quantify the effects of various rock mechanics and operational parameters on the capacity of frictional support systems. The strength of Split Sets is usually measured by means of a pull test wherein a jacking force is applied to the bolt and a slip load is obtained. In order to evolve a rational design procedure for this type of support, an extensive database of over 900 pull test results from more than 50 mines through- out North America has been assembled and analyzed. Associated relevant rock mechanics parameters (rock type and quality) and operational details (drilling method, bit size, drive time, time to pull test) were also obtained, as completely as possible, for each test. Analysis of the information has yielded several charts that relate pull-out strength to relevant parameters and simple statistical analyses were conducted where necessary. Quantified distributions for pull-out strength were also produced for several operating conditions. The factors that most significantly affect bolt strength have been identified and specific applications to design are discussed. The information presented will assist mining engineers in designing safer and more economic support using Split Sets.

Jan 1, 1998

By C. Kim

The integration of three-dimensional (3D) data with infrared thermography has received much attention for its potential use as input data for building energy simulations. Therefore, researchers have proposed methods to integrate 3D data with infrared thermography obtained by different sensors. These studies show the potential of the integration of 3D data and infrared thermography using various systems. However, these studies have ignored property aspects of infrared thermography, such as the low resolution of infrared thermography and external environmental influences. Thus, their proposed methods to integrate 3D data and infrared thermography are inadequate because these problems can affect the resulting building energy simulation. This research proposes a framework that integrates infrared thermography and 3D data while accounting for the resolution and shadow effect of infrared thermography. The proposed framework consists of three steps. In the resolution enhancement step, bi-cubic interpolation is proposed. In thermal data correction from the shadow effect, the shadow area is detected from the visible image, and then the shadow effect is removed from the registered infrared thermography. Finally, enhanced infrared thermography is mapped to the 3D data obtained by a laser scanner. The performance of the proposed framework was evaluated using test images obtained from a building in operation. The experimental results show that the proposed framework provides a 3D thermal model that is useful and accurate in simulating building energy. It is expected that the 3D thermal model can be used for accurate energy simulation of existing buildings. In addition, the proposed framework can be applied in defect detection for buildings. Furthermore, this novel approach enhances infrared thermography using visible images.

Aug 1, 2013

By Mosquera. J.

Tailings Storage Facilities (TSFs) are vast structures that respond to site-specific characteristics, rate of production, placement techniques, and the physical and mechanical properties of tailings. As a common denominator, TSFs are in some degree vulnerable to failure due to liquefaction, poor management, slope instability and/or unusual climatic events. In practice, stability of TSFS is determined by calculating a minimum Factor of Safety (FOS) using the Limit Equilibrium Method (LEM). However, it has been proven that relying exclusively on the limit equilibrium approach is not accurate because it is basically a static method that does not take into account the stress-strain distribution and displacement experienced by the constitutive materials of a TSF. In order to overcome these limitations of the LEM, the finite element method - Shear Reduction Technique (SRT) has been used as a more reliable tool for TSFs stability assessment. This paper presents a comparative stability analysis between an upstream tailings storage facility (UTSF), and a water retention tailings dam (WRTD) under static and pseudo-static states using simplified and rigorous LEMs and the SRT. Additionally, and taking into consideration the intrinsic uncertainty of tailings properties, sensitivity and probabilistic analyses in the form of Monte Carlo Simulation (MCS) and the Point Estimate Method (PEM) are applied to determine the Probability of Failure (Pf) and Reliability Index (ß) of each TSF. It is shown that the friction angle of UTSF?s foundation and the core?s cohesion of the WRTD are the main variables that govern stability. Further analysis shows that the WRTD has a higher reliability index and a lower probability of failure than the UTSF.

Aug 1, 2013

By Maciej Wrobel, Joerg Hammerschmidt, Dana Nurgaliyeva, Alexandros Charitos, Jochen Guentner

"Smelting of copper concentrates in the flash smelter generates a flue dust stream that contains a substantial amount of copper and accumulates more than half of the arsenic input to the smelter. In view of its high copper content flue dust recirculation to the flash smelter is common practice. Globally traded copper concentrates are affected by ever increasing arsenic contents and cause an increasing circulating arsenic load in flash smelter operation. Control of the arsenic level in the smelter slag becomes a challenge. This interaction of arsenic loaded copper feedstock, need for flue dust recirculation and slag quality control call for possibilities to reduce the arsenic load of the recirculated flue dust stream.The technology of partial roasting is known from pre-treatment of copper concentrates before smelting, and gold concentrates before cyanide leaching, to remove the harmful element arsenic. The partial roasting technology can be adapted for use in the purification of the flue dust. A major challenge for flue dust treatment is its extremely fine particle size compared to usual concentrates. For this reason Outotec developed a new process, which allows handling of such fine flue dust. This process solution provides an efficient possibility to reduce the arsenic burden in copper smelter operations.The suggested process aims at reducing the arsenic load to the smelter by treating the flue dust prior to recirculation to the smelter. The presented results are based on test work in the Outotec R&D-centre in Frankfurt. It is possible to remove 80-85% of the contained arsenic and to collect it in an arsenic trioxide residue with a concentration above 90%. The final off gas contains SO2 from decomposition of sulphates that are contained in the flue dust. The off gas stream is relatively small. We assume that it is possible to combine the off gas stream with other smelter process gas streams and to treat it in an existing sulphuric acid plant. Coal is used as fuel and as reductant to reduce pentavalent arsenate to trivalent arsenite. Arsenite can be kept in gas form at temperatures above 450°C. This permits separation of a calcine stream with arsenic levels of 0.2 – 0.3%, which is recirculated to the furnace.Outotec has a wide range of roasting testing facilities from lab-scale to pilot-scale. Outotec has both capability to modify and adapt technology to specific ore or concentrate requirements, but also the necessary infrastructure in its research centers in Frankfurt and Pori to do appropriate validation tests in lab and pilot scale size plants."

Jan 1, 2016

By M. A. Cawley, J. W. Jordan

"IntroductionTHE ORE PILLARS in the lower ""A"" ore body of Waite Amulet Mines, Limited, can be divided into two groups, those mined in the open by sub-level blast-hole methods, and those to be mined .against coarse rock fill. Of the three pillars in the last group one has been mined and is dealt with in this paper. The method of mining pillars against coarse rock fill was suggested by the late Dr. Oliver Hall, who was Consulting Engineer for the Company when recovery of No. 2 East pillar was being planned.HistoryThe Waite Amulet mine is in northwestern Quebec, nine miles north of the town of Noranda. The property is approximately three miles long by one mile wide. The present Company, which was formed by the amalgamation of Amulet Mines, Limited, and Waite Ackerman-Montgomery Mines, Limited, commenced operations in the summer of 1937. In the fall of 1939 a new .flotation mill was erected with a capacity of 1,200 tons per day, which was increased to 1,800 tons per day in 1943. The mill is presently operated at 1,400 tons per day.To date, seven orebodies have been found, the major ones being Lower A, East Waite, and Waite. Three separate concentrates are produced, copper, zinc, and pyrite. Total tonnage mined to the end of 1954 from all orebodies has been 7,340,000 tons, which averaged 4.6 per cent copper, 5.3 per cent zinc, and 0.037 oz. gold and 1.27 oz. silver per ton."

Jan 1, 1955

By PAULL. BROUGHTON

Commercial deposits of sodium sulphate are harvested from alkaline lakes that are widespread throughout semi-arid southern Saskatchewan and adjacent southeastern A lberta. Concentration of sodium sulphate occurs in undrained basins under semi-arid conditions. Precipitation runoff from land adjacen1 to 1hese basins leaches 1he mineral from the soils and carries it in solu1ion 10 the basins. The process may be largely subsurface, wherein spring seeps feed basins associated with buried (preg/acial) river valleys. Evapora1ion during summer concentrates salts in the brines, and chilling of water below sa/Uration poin1 during win1er resu//s in deposi1ion of sodium sulpha1e (mirabili1e) crystals on lake bo//oms. Sodium su/pha1e, commercially known as sa/1 cake, ranks second only 10 po1ash in cen1ral-wes1ern Canada's nonme1allic mineral production. // is recovered from su,face brines, directly from intermittenl salt beds, and, until recently, by solution mining of shallow subswface deposits. Sodium sulphate is extrac1ed from seven alkaline lakes and sail f/a1s in Saska1chewan and one in Alberta. Annual produc1ion is approxima1e/y a halfmillion tonnes. Manufacture of kraft paper is the mos1 significanl marke1 for salt cake, but addi1ional quantifies are used in the glass and detergent manufac1uring indus1ries.

Jan 1, 1984

By S. Surapunt, C. M. Nyamai, K. Itagaki

"The use of liquid copper as a medium for zinc extraction has been used in the Warner Process as a method of processing zinc-lead sulphide ore. The recovery of zinc metal is based on the reaction:ZnS(s) + 2Cu(l) = Zn(g) + Cu2S(l)In this method, thermodynamic and phase equilibria investigations of the Cu2S-FeS-ZnS and Cu2S-PbS-ZnS systems are of importance and form the basis for the liquid sulphide phase which appears as a product and is used as a solvent in the Warner Process. Phase relations in the Cu2S-FeS-ZnS and Cu2S-PbS-ZnS ternary systems were determined experimentally at 1473°K to provide a fundamental basis for the new zinc smelting process. The results show that the solid solubility of ZnS in the two systems is very small (2 wt% to 3 wt% ZnS in FeS, 4 wt% ZnS in Cu2S for the Cu2S-FeS-ZnS system; less than 0.5 wt% ZnS in both PbS and Cu2S for the Cu2S-PbS-ZnS system). The Raoultian Activity Coefficient of ZnS in the liquid mixtures and the vapour pressure of zinc over the matte in both systems is relatively large (?° = 7.7 – 15.8, Pzn(atm) = 0.088 – 1.026 for the Cu2S-FeS-ZnS system; ?° = 8.9 – 12.9, PZn(atm) = 0.075 – 0.214 for the Cu2S-PbS-ZnS system). On the FeS-ZnS join, the only phases detected are FeS and iron-rich sphalerite (Zn, Fe)S. The binary join mixture occurs at about 92 wt% FeS-8 wt% ZnS at 1473°K. Electron microprobe examination of the quenched samples indicate about 47 wt% to 48 wt% FeS in sphalerite and about 2 wt% to 3 wt% ZnS in the iron sulphide phase. On the Cu2S-ZnS join, microprobe analysis reveals that the maximum solubility is 4 wt% Zn in liquid Cu2S and 3.6 wt% Cu in solid ZnS. In the Cu2S-PbS-ZnS ternary system, microprobe analysis of the quenched samples indicate on average, 5 wt% ZnS in the liquid phase region. The only phases detected on the PbS- ZnS join are ZnS and PbS. The eutectic phase contains, on average, 13 wt% ZnS. The phase relationships, very low solid solubilities of zinc sulphide in the liquid mixtures of both Cu2S-FeS-ZnS and Cu2S-PbS-ZnS systems, coupled with the high Raoultian Activity Coefficient of ZnS as well as the high vapour pressure of zinc over matte all favour the partitioning of zinc metal into the vapour phase. This new process is cost effective and bypassesthe expensive and tedious conventionaltechnique of zinc production involving oxidationof the sulphide ore by roasting followed bya reduction process to extract the zinc. Theresults indicate that a new zinc smelting technologyusing the Warner Process would bemore efficient and preferable over the traditionalmethods of zinc extraction."

Jan 1, 2002

By R J. Tremblay, R. R. Hoffman

This paper deals with materials of construction and problems encountered and overcome in leaching and filtration of oxidized sulphuric acid slurry in the Port Radium mill after eight years of operation. The slurry is characterized by a high calcium sulphate content as well as a high chloride level under oxidized conditions, both of which affected initial design and subsequent changes. Leach agitation tanks are of wood with a mild steel superstructure and stainless steel agitator and moving parts below solution level. Electro-polished 316 stainless steel cooling coils are used for temperature control of the slurry. The string filters are of the Oliver type with wood decking. Extensive use is made of wood, Linatex lined mild steel and stainless steel for the slurry handling. A typical analysis of the slurry solution follows:(pH-1.30) ClOa Fe+++ Free Acid UaOs c1-so.--0.10 gms/litre 10.2 gms/litre 6. 7 gms/litre 3.5 gms/litre 2.0 gms/litre 155 gms/litre

Jan 1, 1961

By R. A. Campbell

Pig iron and silicospiegeleisen were produced experimentally from a very low-grade manganiferous iron ore from Steep Rock, Ontario, by a two-stage electric smelting process. The most favourruble operating conditions were determined for each stage. Cement clinker then was made by calcining the slag from the second stage of smelting, with additional limestone and alumina. (This slag would normally be a waste material). The cement clinker produced had the composition of commercial Portland cement, and met the physical test requirements of the Canadian Standards Association Specification A5-1951 for normal Portland cement as well as could be expected for a material produced on .such a small scale.

Jan 1, 1958

By A. L. Mular

Some specific cases of the collection of data from industrial grinding and classifying operations, and the development of models from the data so obtained, will be described. The problems encountered, the effort involved, and the value of the derived models in improving the plant efficiencies will be discussed and documented where possible.

Jan 1, 1971

By V. L. Gravitis

Radioisotope X -ray techniques of analysis for nickel have been tested in laboratory and plant trials. In the laboratory tests. a comparison was made of radioisotope and conventional analyses for nickel in solid s samples taken from streams of a nickel concentrator. Coefficients of variation of 1.7% for feed and concentrate samples , and equal to 10% for final tailing samples, were obtained. Continuous determination of nickel in final tailing slurries was demonstrated in a trial lasting 20 days at a nickel concentrator (Western Mining Corporation), nickel being determined with a standard error of 0.036% Ni in the slurry solids within the range of 0.24 to 0.68% Ni. This error, obtained by comparison of on-stream probe analyses with assays of samples taken from the stream, includes errors in sampling and assay by conventional techniques.

Jan 1, 1977

By B. Currie

Maintenance of quality electrowon copper requires an electrolyte which has suitable chemical and physical characteristics. The proper design and operation of the solvent extraction plant is essential to the quality of the electrolyte sent to electrowinning. An aspect that is not well appreciated is that the return electrolyte can have negative effects on the operation of the solvent extraction plant. Poor SX plant operation creates below optimum electrolyte conditions. High Eh in the return spent electrolyte can degrade the SX reagent with large decreases in copper transfer capacity and increases in internal entrainment. The synergistic interaction of the SX and EW plants needs a single-source design approach to address the interactions. The design elements in the SX and EW plants required to manage the electrolyte conditions are discussed.

Jan 1, 2014

By B. R. Richards, B. G. W. Robinson

"This paper shows how metal values can be profitably won from a comparatively small and remotely located but high-grade orebody. To do so is not uractical for a large mining company, with its necessarily high overhead of services and organization essential to a large producer.To evaluate, develop and profitably exploit a limited but defined ore deposit becomes only a problem of determining the dollars required to win the dollars available. This paper will record how this was carried out during 1965 and at the same time describe the history, development and production plant of this property."

Jan 1, 1966

By George B. Saunders

It is the purpose of this paper to point out conditions as they exist in the merchandizing of coal, to compare these conditions with methods in use by competitive producers of coal substitutes, and to present briefly some suggestions which may help the individual operator to market more coal in the immediate future, while we are waiting for the scientist and research worker, who are now busy on coal betterment , to produce in a practical way the results which they now write about in such glowing terms. While it may be unnecessary to call the attention of coal operators to the present deplorable condition of the industry, it might be well to impress upon our members in other branches of mining, as well as upon the public at large, the seriousness of the situation. Emerging from the war and the period of reconstruction that followed, the coal industry found itself with too many mines and too many men for normal conditions. To make matters worse, the interruptions in deliveries caused by strikes, the unfavourable publicity caused by socialistic propaganda, and the repeated governmental investigations, made the market a fertile field for coal substitutes which were not so handicapped. These substitutes were well advertised, and were marketed in an up-to-date manner, furnishing an example from which the coal operator could well profit. Now, whether or not there is agreement as to the cause or causes of this condition, there can be no doubt that we are today face to face with the fact that the sale of coal has not kept pace with the sale and use of other commodities. Had it done so, we would ere this have been able to take care of the surplus labour and work our mines at least approximately full time.

Jan 1, 1929