Search Documents

By Gillyeard J. Leathley

The Cassiar Asbestos mine is situated on McDame Mountain in northern B.C. at a mean elevation of 6000 ft (1830 m), some 6 miles (9.6 km) from the townsite /mill complex. Asbestos ore production averages 1,200,000 tons at 9% R.M.G. (Recoverable Mine Grade) and waste production is 6,000,000 cu. yd annually. Waste is loaded by P&H 1900 AL 11-cu.-yd shovels and transported by 75-ton and 85-ton end-dump trucks to the waste dumps. The ore is loaded by a 992 Caterpillar 10-cu-yd front-end loader into 50-ton and 75-ton trucks, which transport it to the crushing plant located at the mine. The ore is transported by a 15,370-ft (4685-m) tramline to the mill complex.

Jan 1, 1978

By J. S. Fox

"Besshi-type Cu-Zn (-Ag-A u ± Co) deposits are tabular, stratiform volcanogenic sulphide bodies which are usually associated with mafic volcanic rocks of oceanic or intra-plate geochemistry, but which can also be found locally with ultramafic volcanics or subvolcanic mafic intrusions. A thick sequence of continentally-derived clastic sediment usually encloses both the mafic volcanics and the ore. Besshi-type deposits form subaqueously, in epicratonic rifting environments, more-or-less proximally, and as a result of hydrothermal convection in their subjacent mafic volcanic - clastic sedimentary piles. They belong to a rift -related metallogenic spectrum that includes sediment-hosted and Cyprus-type base metal deposits, and may diller genetically from these mainly with respect to rate and degree of crustal extension. Modern analogues to these deposits are f ound in the submarine volcanogenic sinters of the Gulf of California rift system.The associated lithologies and tectonic selling of Besshi-type deposits clearly distinguish them from Kuroko-type ores. This difference also seems to be reflected in their lead isotopic character. For example, leads from Besshi-type deposits in the Sanbagawa belt of Japan and from the Blue Ridge belt of southeastern U.S.A. lie on extended anomalous lead lines and have lowslopes in 207Pb/204 Pb - 206Pb/ 204 Pbspace (Sato and Sasaki, 1980; Leriuray, 1982), wheras those from most Kurokotype mining districts exhibit only narrow isotopic ranges and lie near or on the orogene growth curve (e.g. , Franklin et a I., 1981). More over, where Besshi- and Kuroko-type deposits are found in the same orogene, the former often occur earlier in the tectonic cycle than the tatter (e.g., Japan, the Norwegian Caledonides, the southern Appalachians and south-central Finland).Besshi-type deposits are not confined to any particular part of the world, or to any geological epoch. Moreover, in many mineralized belts, Besshi-type deposits are the predominant volcanogenic ore type. On a world-wide scale, deposits of this type therefore constitute an important base metal resource."

Jan 1, 1984

By Vishal Shukla, Prateek Singh, D. P. Chakraborty

"Continuous thickening by an operation called sedimentation is the separation of suspended solid particles from a liquid stream by gravity settling. The primary purpose of thickening is to increase the solids concentration of the feed stream. High rate thickeners are designed specifically to maximise the flocculation efficiency. A detailed investigation has been carried out to understand the influence of ore type and operating parameters such as bed level, bed mass, rake arm torque and flocculent concentration on thickening operation. Tata steel’s Noamundi plant data shows that variation in ore type, and operating parameters are major contributors to fluctuation in thickener performance. A lot of research has been done earlier on thickening operation but effect of ore type and operating variables by using plant data was never touched before.In this context, the performance of thickener was evaluated by daily data to study the influence of ore type and operating variables on thickener operation. Investigation shows that friable ore % in feed mix is proportional to slime density because friable ore is porous & brittle in nature. As a result, friable ore generates more fines/ultrafine during communition process in wash plant. Increase in flocculant concentration and bed mass is showing a positive change on high rate thickener performance Investigation shows that optimum bed mass and flocculant concentration is required to achieve desired pulp density in thickener underflow at different feed pulp density (g/cc).INTRODUCTIONOver the years, Iron Ore Beneficiation at Tata Steel, Noamundi has seen varied changes. Depletion of high grade iron and with increasing iron ore throughputs coupled with lowering of the hard ore a subsequent increase in slime generation, slime management and clear water requirement for wet Plant has thrown up myriad challenges. To overcome these challenges, many improvements initiatives were taken by Tata Steel in last decade. One of the major changes is the recent High Rate Thickener commissioning at Tata Steel Noamundi to cater the high iron ore throughput requirement. Slime reporting to Thickener has increased from 1.4 MTPA 2.5 MTPA over the last few decades. The above changes further aggravate the poor settling and dewatering characteristics of the slurry which is being feed to HRT. Considering the above mentioned constraints and stringent environmental implication proper water management has become a major challenge to reckon with. The thickener is used to increase the concentration of the suspension by sedimentation, accompanied by the formation of a clear liquid. In most cases the concentration of the suspension is high and hindered settling takes place."

Jan 1, 2016

By Dennis Hoffmann

"Abstract - Banded iron formation rocks associated with massive sulfide lenses in the Broken Hill Pb-Zn-Cu-Ag deposit in the Namaqualand Metamorphic Complex, South Africa , were investigated with respect to the geochemistry of manganiferous silicate-rich bands. Two common varieties of these are: amphibole- and garnet-rich iron formation bands. The results reveal that the former are enriched in Fe, Mg, Cu, Co and S. The garnet-rich bands are enriched in Mn, Ca, P, Pb and Ba with significant detrital contamination of Ti, Al, Zr, Cr, Y, V, Ni and Nd.The silicate-rich bands have compositions, in terms of, Si/Al, Si/Fe, Fe/Mn, La/Ce and Co/Zn, comparable to submarine chemical sediments which precipitated from hydrothermal fluids. The garnet­ and amphibole-rich bands are interpreted as ""evolved"" and ""immature"" hydrothermal sediments, respectively. The latter resulted from rapid precipitation after exhalation, whereas the former had a longer residence within sea water. The silicate-rich bands both exhibit increasing Mn/(Mn+ Fe) fractions, which are consistent with a variation expected from proximal to distal depositional settings. The prevalence of garnet-rich bands over amphibole-rich bands is interpreted as the result of injection of hydrothermal fluids from a single vent situated along the northwest margin of the Broken Hill deposit."

Jan 1, 1994

By Raj Rajamani

In general, many past works examine mill load, mill power, shell lifter design etc with a view to improving the mill capacity. On the contrary, only a handful of papers have addressed the transport of fine slurry through the pulp lifters. We present the flow dynamics of pulp lifters via laboratory scale experiments, high speed photography and modeling with computational fluid dynamics. Next, the flow behaviour in ArcelorMittal?s Mont-Wright autogenous mill discharge flow is examined. In an effort to improve mill throughput, a comprehensive simulation and plant scale study of the mill was taken up with a focus on the shell and pulp lifter design. The shell lifter was found to be at its optimum limit for breakage of ore particles given the constraints of wear life and occupied volume. Next, the pulp lifter study was taken up with computational fluid flow code and discrete element code. The simulations directly showed that there was considerable carry-over of slurry. This effect was traced to the area restriction in the pulp lifter channels. Further, crash-stop studies confirmed slurry pooling within the mill. Thus it was readily apparent that mill throughput can be increased if the pulp-lifter could be redesigned. Consequently, the discharger section of the pulp-lifter was redesigned. First, this paper outlines the modeling in laboratory scale studies and plant scale studies leading up to the discharger design. Next, the discharge flow in seven different published mill surveys is predicted with computational fluid dynamics (CFD) methodology shown here. Finally, Mont-Wright mill circuit performance before and after the discharger redesign is described. The usefulness of fluid flow simulations in the design of pulp-lifters is emphasized.

Jan 1, 2012

By R. J. A. Fricker

IT is the purpose of this essay to give a reasonably complete description of shaft sinking under a rock pentice in a small Northern Ontario gold property. Hallnor is in many ways an exceptional mine, but the sinking operations here described are but typical examples of the excellent practice for which Canadian mines and mining engineers are justly famous the world over. The worth of the subject lies, therefore, nor in its originality, but in its soundness; not in the spectacular, but in the economical and safe. Attention is particularly drawn to the excellent safety record and to the exceptionally low overall sinking cost. INTRODUCTION Prior to April, 1939, the Hallnor No. 1 shaft had been sunk vertically to a depth of 997 feet below the surface. It is a three-compartment shaft, 19 ft. 10 in. by 7ft. 7 in. outside the timbers (see Figure 1).

Jan 1, 1941

By Walter Greaves

THIS paper describes a series of tests performed at the Hollinger mill during the past four years, in which both metal and rubber-lined pumps were used for pumping sand and slime. While conditions will not be the same at other mills, it is felt that the information gained from the tests should be of value to other operators and of assistance to them in selecting the most efficient size of pump and kind of lining for economical operation. For the successful operation of pumps with rubber linings there are certain conditions, which, if recognized at the outset, will save the operator a good deal of work and trouble. First is the necessity of keeping sharp pieces of steel, or anything that might cut the lining, out of the pumps. This can be effected by placing screens in the proper locations. Second is to recognize the fact that the rubber lining of the shell, and the rubber cover of the impeller, are subjected to very different conditions. The shell lining, :being at rest and well supported by the metal case, has a relatively easy job compared ? with the impeller covering, which is subjected to centrifugal force and has a tendency to tear itself away from the metal core. Also, the pulp travels through and past the impeller at a high velocity. These two factors, centrifugal force and velocity of the pulp, would appear to set a limit to the speed at which, for a given set of conditions, it is economical to run a rubber-covered impeller. Therefore, a pump should be large enough for the work to be done. To get the best mechanical efficiency, it must be operated somewhere near the limit of its capacity, but this may not give the best overall cost, because the saving in power, due to the high efficiency, may easily be lost through excessive wear on the lining. It would appear that this condition is more critical in a rubber-lined pump than in one lined with metal.

Jan 1, 1939

By W. A. Roliff

The renewed interest of the past few years in the Appalachian and Michigan oil provinces has not, as yet, created any marked increase in activity in Southwestern Ontario. During 1960 development drilling in-creased somewhat over 1959, but exploratory drilling decreased slightly. More attention was devoted to the deeper horizons, but lake drilling de-creased considerably. Oil production reached a new peak and gas production increased slightly. During 1960 an interesting oil and gas discovery was made in the Cambrian and gas discoveries six miles off-shore in the eastern part of Lake Erie were made in the Clinton-Cataract zone of the Silurian. This paper reviews activities during 1960, summarizes the discoveries made to-date and the pertinent exploration data relating to the prospects of the region and discusses some of the economic aspects of exploration and development. D URING the last few years there has •been a marked renewal of interest in the old petroleum

Jan 1, 1961

By G. V. Sirianni, G. E. Viens, R. A. Campbell, G. N. Banks

A combination shaft-electric furnace for the smelting of ores and the melting of metallized feed is being developed at the Mines Branch. When iron oxide pellets are smelted in this unit, they are preheated and partially reduced in the shaft before being transferred to the electric furnace where smelting is completed. Also, limestone flux added with the pellets is-preheated and calcined in the shaft. It has been demonstrated that, in smelting iron oxide in this unit, the throughput of the 250-kva electric furnace can be approximately doubled and the amount of electrical energy required can be very significantly reduced when the shaft furnace is operated in conjunction with the electric furnace. These benefits are achieved mainly by utilizing the sensible heat and latent energy contained in the arc furnace off-gases.

Jan 1, 1971

By K. J. G Hedges

"Once a health based guidance limits for exposure to diesel exhaust have been established, and as part of a multi-disciplinary team, the program for exposure reduction should incorporate the plan-do-check-adjust cycle. Setting a suitably protective (health based) occupational exposure limit (OEL) for diesel particulate matter (DPM) and nitrogen dioxide is a key driver to reduce exposure. It is important to go beyond regulations and reduce exposure to diesel exhaust, DPM, as low as reasonably achievable (ALARA) such as that prescribed under the Australia, Queensland Mining and Quarrying Safety and Health Regulation 2017 where under section 135 Limiting workers exposure, the workers exposure must not exceed the exposure limit applying to the worker for the hazard; and is ALARA. It appears that previously acceptable OELs are no longer safe. Therefore it is important that the internal responsibility system be implemented and the precautionary principle approach be followed, especially as it may be some time before a suitably protective OEL specifically for DPM is in place. One leading multi-national mining company BHP Billiton has acknowledged a significant lag that exists between regulatory action and the level of science that informs health risk. This company is managing exposure to diesel exhaust to as low as technically feasible. This same company that has set an interim target for managing diesel exhaust to 0.03 mg/m3 is achieving these levels which paves the way for other mining companies and general industry including construction. The Occupational Cancer Research Centre 2017 recommends reducing personal exposure to within 0.02 mg/m3 (EC) for underground mining and 0.005 mg/m3 for other workplaces. Controlling DPM is important to prevent cancer however it is also important that that nitrogen dioxide (NO2) be reduced (ALARA) and that careful selection of control technology be considered such as the proper selection of a diesel oxidation catalyst so that the level of NO2 does not in fact increase. The example from BHP Billiton provides a leading practice including using a multi-disciplinary approach and the importance of controlling emission at source and having an auditable diesel emissions based monitoring program in place."

Jan 1, 2019

By N. R. Andrade-Gonzalez

In this paper, the effect of magnesium and strontium additions on the heat treatment behaviour of cast A319,2 alloy was investigated, Permanent mold samples were heat treated at 495 °C for 4 and 24 h, then quenched in hot water and aged at 180 °C and 220 °C for different temperatures, It is found that multiple aging peaks are present in the age-hardening curves of Al-Si-Cu alloys, mainly when Mg and Mg-Sr are added, The results of electron probe microanalysis (EPMA) observations reveal that the age-hardening behaviour is related to the precipitation sequence of alloys, For the Al-Si-Cu alloy, the first aging peak is the result of the high-density GP zones, while the subsequent peaks arise from metastable phases, Obvious intervals during the transition from GP zones to metastable phases may be the main reason of the formation of multiple aging peaks, It is seen that addition of Mg (-0,40 wt %) leads to the precipitation of coarse Al5Mg8SioCu2 particles. When modifying the high Mg alloys, Cu-intermetallics segregate in areas away from the growing Al-Si eutectic regions, Modification with strontium retards the precipitation of the silicon out of the matrix.

Jan 1, 2005

By David Runnels

The Mount Wright iron are mine and upgrading plant were brought on line in the fall of 1975. The mine is located near the Quebec - Labrador border some six hundred miles northeast of Montreal. This paper describes the crushing, grinding and concentrating facilities at Mount Wright, and some design: criteria used in equipment selection and flow sheet design. Also mentioned are some "asbuilt" modifications. A brief description of the over-all flowsheet is also included. Introduction IN SEPTEMBER 1970, the Quebec Cartier Mining Company started development of the Mount Wright iron ore mine. The estimated are reserve is in excess of 1,000,000 ,000 long tons of concentrates, with an average crude are grade of 31.5% Fe. The run-of-mine ore is crushed, ground and concentrated to a product having 66% Fe and 5% silica at an annual concentrate production r ate of 18.4 million long tons. The daily production rate of over 50,000 long tons of concentrate necessitates a daily mine output of approximately 250,000 long tons of material, of which 50% is waste.

Jan 1, 1977

By Cale J. Dubois

At Cameco Corporations' Cigar Lake Project, large excavations are developed on the 480 Level and 500 Level must remain stable for at least 15 years to host underground processing infrastructure. Following the successful dewatering of the mine in October 2009, subsequent internal rockmechanics investigations augmented by third party technical investigations; determined that to keep the back of the Water Flush Crusher/Run-of-Mine (WFC/ROMs) excavation stable; required a rehabilitation strategy to mitigate deterioration/deformation of the WFC walls and intersection pillars. The mechanism of failure propagating the movement of the excavation walls is understood to be controlled by the presence of a dominant E-W striking and steeply dipping foliation within a relatively weak and mildly altered rockmass sub-parallel in strike with 14 meters high walls and an intersection span approaching 15 meters. The application of open and resourceful communications between site mining engineers, geologists, contract mining staff, construction management experts, corporate mining and civil engineers, and third party technical experts resulted in a multi-faceted short-term ground support strategy consisting of standard bolting and screening, deep-seated modified-strand cable bolts coupled with heavy gauge mesh straps, rockmass reconditioning using low-pressure grout injection, and horizontal cable-lacing for the intersection pillars applied in lifts using a top-down methodology. The intention of the short-term strategy was to stabilize the excavation so that a long-term structural steel support installation - consisting of composite concrete walls, and arch support applied to the side walls and crown of the back - could be constructed safely. This paper summarizes the evolution of the short and long-term ground support strategy and criteria for the WFC/ROMs excavation developed using elements of civil, mining and hydrogeologic design.

Nov 1, 2011

By Dave Thomas

?Uranium is a common trace metal at the earth?s surface, but these are amazing super-high grade (up to 25%) pods, veins and disseminated uraninite (UO2) near unconformities between Proterozoic siliciclastic red beds and metamorphic basement with graphitic metapelite and radiogenic granite. ?Pitchblende fills extensional features in reactivated fault zones and replaces matrix in sandstone ?One mining district in Canada ?the Athabasca Basin ->30 deposits /prospects -most in eastern ¼of basin -produces 1/3 of world?s U -employs northerners -VERY high tech -VERY high safety standards Unconformity-associated uranium depositsUnconformity-deposits

May 1, 2006

By J. A. Brusset

Introduction The West Canadian Collieries, Limited, operate three bituminous coal mines in the Crowsnest Pass district of Alberta. Two seams are worked; their thickness varies from 10 to 20 feet and their pitch from 10 to 45 degrees. The Bellevue mine was opened in 1903, the Greenhill in 1914; both are gassy and dusty, and at both the haulage is a problem, as the workings are spread over distances of several miles. Compressed-air locomotives are used at Bellevue, rope-haulage at Greenhill, both of which solutions of the haulage problem are costly in installation an operation, and lack flexibility. In 1943, the Adanac mine was opened; and the question soon arose as to which system of haulage should be selected. Compressed-air locomotives and ropes were rejected on the ground of high cost. Since, under the Alberta Mines Act, the use of trolley locomotives underground in coal-seams is not permitted, the choice lay between storage battery locomotives and Diesel locomotives. The preference of the author, who had had experience with both in French gassy coal mines prior to 1930, was for Diesel locomotives, due to lower cost of installation and greater flexibility and reliability. However, Regulation No. 13 of the Mines Act of Alberta reads: 'No gasoline-driven engines shall be used underground in any mine, and no internal combustion engine shall be used underground in any coal mine, except only when authorized by the Chief Inspector in writing, and on such terms as he may prescribe"

Jan 1, 1948

By J. M. Mwase

The platinum group metal (PGM) industry is currently reliant on the crush-mill-float-smelt-refine route to process PGM ores. However, there are many instances where this route would not be feasible. An alternative process route has been developed which involves heap bioleaching to extract base metals followed by heap reclamation and a water wash step, leading into heap cyanide leaching to extract precious metals. This process was evaluated through test work on samples of Platreef ore using laboratory scale columns. After 304 days 75% Ni and 93% Cu were extracted in the bioleach experiment at 65°C, and after 60 days 58% Pt, 99% Pd and 90% Au in the follow-up cyanide leach experiment at 50°C. A preliminary process flow sheet has been developed around this. Analysis via a mineral liberation analyser showed that the remaining Pt was in the form of the mineral sperrylite, which appeared to be slow leaching in cyanide in comparison to the other mineral types. Analysis of cyanide effluent solution showed high levels of thiocyanate, which present an environmental risk for disposal and high consumption of cyanide. Further studies to develop the process for commercial application in the South African PGM industry are outlined.

Jan 1, 2014

By M. E. Holuszko

Although there is no widely accepted rigorous definition of handleability, the handling coal characteristics often referred to as handleability define whether a coal has the ability to flow unhindered through the processing and transportation systems. The handleability may be severely affected if fine coal particles tend to aggregate. In the pelletization process, the rolling action of the drum is applied to bring the individual particles into proximity with each other so that they can aggregate and form pellets. Because of apparent similarities between these two processes, the pelletization tests are carried out in parallel to the handleability tests in this project, and the pelletization results are used to explain coal handleability properties.

Jan 1, 2004

By T. G. Joseph, E. Lampard

ABSTRACT: Surface mining operations must manage variability from within their operations as well as variability imposed upon them by external forces. A framework to manage both internal and external variability through the continuous review and adjustment of a mine plan during active mining lifetime operation is introduced, to minimize lost production and maintain operational safety. The observational approach of “observe, evaluate, interpret, predict, and adapt” is employed as the backbone of this approach. Although written with a surface mining operation in mind, the framework outlined in this paper would be equally applicable to any mining or processing operation.

Jan 1, 2011

By D. E. Parson, W. A. Morgan

This paper offers a brief review of current literature pertaining to vacuum degassing or vacuum casting of steel as practiced in the U.S.A., Germany and the U.S.S.R. The advantages of vacuum degassing of large forging ingots, heavy section casting, for the conversion of rimming bessemer steels to killed steel and for the production of transformer steels are discussed. Operating pressures, reduction in gas contents and improvements in hydrogen segregation, steel cleanliness and mechanical properties, obtained with the various techniques, are described. The paper includes a description of an experimental vacuum stream-droplet degassing unit and some preliminary results obtained at the Physical Metallurgy Division Research Laboratories Department of Mines and Technical Surveys, Ottawa on laboratory steel melts. Experimental 500 lb direct arc, basic melts have been spray cast into either ingot moulds or dry sand moulds, held inside a vacuum tank. Also 500 lb melts have been

Jan 1, 1961

By Frank Mucciardi, Zhongsen Yuan

A new heat transfer technology --- termed Thermopump technology has been developed. This technology originates from conventional heat pipe configurations but has now evolved into its own class of heat transfer units, which we refer to as `Thermopumps (TP)'. A key feature is that Thermopump technology can be applied to high temperature / high heat flux environments where conventional heat pipe technology fails. Moreover, when implemented in less demanding applications where heat pipes appear to operate, Thermopump units have been found to function more smoothly and reliably. This paper will introduce Thermopump technology and several applications of this technology in steelmaking and refining will also be discussed. In addition, this paper will focus on three classes of applications: 1) waterless, non-consumable, high efficiency Thermopump oxygen lance and/or burner for EAF's, 2) Thermopump ladle lance for the desulfurization process, and 3) Thermopump cooling panels for furnace walls and roofs. Facilities equipped with Thermopump technology are expected to he better than the current corresponding ones in terms of increasing productivity and energy efficiency while at the same time lowering operating costs.

Jan 1, 2004